PROVN OF FENCING WITH BARBED WIRE IN MH BHUJ AND CERTAIN MINOR WORKS AT MIL STN BHUJ UNDER GE(ARMY) BHUJ

Amount

M&L for 30mm thick mastic asphaltic flooring as per IS 1195 and IS 1196 as directed by Engr In charge all as specified

M&L rendering 10 mm thick in CM 1:6 on PCC block masonry brick work or concrete surfaces to be finished even and smooth without using extra cement in internal walls.

M&L rendering 15 mm thic in CM 1:4 on PCC block masonry brick work or concrete surfaces to be finished even and smooth.

M&L preparing new plastered surfaces of wall & apply three coat of white wash over a coat of lime putty cpmplete all as specified and directed.

M&L preparing new plastered surfaces of wall & apply two coat of coloured cement base paint over one coat primer using white cement on all external wall.

Pre-cast cement concrete block Type C1 1:3:6 (20 mm graded aggregate) masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete

m&L two coat of synthetic enamel paint over 10 cm width or girth,not otherwise described over a coat of redoxide on new surface incl preparation

S&F Roof trusses (framed) trusses purlins and fastening (etc.,angle, channel,tubular section,round pipe) or flat section including distance pieces, MS plates/ gusset plates, cleats, hold fast etc. conforming to Gde of steel Fe 410-0 or Fe 310-0 complete all as specified and directed.

S &F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering / cladding to wall, fixed with L or J hooks all as specified and directed.

M&L for PCC (1:4:8) type D-2, (using 40 mm graded stone aggregate),75 mm thick, as in sub base for floor, finished even and rough complete all as specified and directed.

M&L PCC 1:2:4 type b1 using 20mm graded stone aggregate as 25mm thick finished fair all as speificed

Excavation in trenches not exc 1.5 mtr depth for foundation etc n.exe 10sqm on plan in and getting out in hard dense soil.

M/L for providing PCC 1:4:8 type D2 using (40mm graded stone aggregate) in foundation, filling and mass concrete, levelling course etc.

Returning filling in including spreading, levelling, watering and well ramming in layer nexc 25 cm in soil

Removing excavated material soil n.exc. 500m and depositing where as directed

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings aldrops ,ttower bolts etc (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L Plain, galvanised, mild steel sheeting 0.80 mm thick in stepped flashings (measured as the minimum rectangle from which the piecescan be cut) for door covering including all welding as direcetd

S & F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; ailings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 75 mm thick, watered and rammed to a true surface

PCC for 50 mm thick (1:3:6) type D-2 using 20 mm graded stone aggegate

M&L TMT bars 10 mm dia and over cut to length bent to shape required including cranking,bending,spirally for hooping and binding with and including mild steel wire anealed not less than 0.9 mm dia

Ditto but 5 mm dia and over up to and including 10 mm dia in stirrups spacers and binders

Reinforced cement concrete (Design Mix, M-25) in beams, cantilevers, bressummers, lintels over 1.50 meter span

Reinforced cement concrete (Design Mix, M-25) in Chhajha

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels cantilevers, shelves including supports, overhungs etc. also splays between floors and beams etc. as in rough finished surfaces.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Hard/Dense soil.

M & L PCC (1:4:8) type b2 for Footing all as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm inHard/Dense soil.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point inHard/Dense soil.

S & F TMT bars 10mm dia & over of Grade Fe 500d incl cutting, bending, binding & placing in position with binding wire.

Ditto but 5 to 10mm dia in stirrups, spacers & binders.

M & L Pre-cast cement concrete block masonry type C1 1:3:6 with solid blocks, exc. 10 cm in idth and setting in mortar, ompletebuilt in CM (1:6)

M & L 8mm dia TMT reinforcement Fe 500d for partition wall

M & L RCC- M-30(Design Mix) using 20mm graded aggregate for G.Floor Lintel Band

Use & Waste Form work for rough finished surfaces of concrete measured flat for G.Floor Lintel Band

M & L RCC- M-30(Design Mix) using 20mm graded aggregate for G.F Chajja

Use & Waste Form work for rough finished surfaces of concrete measured flat for G.F Chajja

M & L 10mm thick cement plaster in CM (1:6) internal finished even & smooth

M & L 5mm th. Setting / finishing coat in CM 1:3 over soffit of RCC slabs landing, waist slabs, beams, roof/chajja projection roof Ceiling etc.

M& L for 15mm Thick External Plaster in CM ( 1:6 ) all as drirected and specified.

Supply only Integral waterproofing compound

S & F 125 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S & F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S & F Anodised aluminium frame with powder coating for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F 4.0 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S & F 100mm long Butt hinges, heavy weight, cold rolled mild steel, and fixed

S & F 200 mm long 10 mm dia Al tower bolt

S & F 150 mm long Mild steel pressed handles, oval type, stove enamelled black

S & F 150mm Long, 16mm Dia Alu. Aldropbolt

M & L Three Coats of White Wash on Wall

M & L Three Coats of White Wash on Ceiling

M & L Two Coats of Exterior Emulsion paint(weatherproof paint) over one coat of primer

Two coats of synthetic enamle paint over a coat of Zinc Cromate primer over prepared surface steel

Two coats of synthetic enamle paint over a coat of white/ pink primer over prepared surface of wood

M & L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L For Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M & L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M& L for Screed bed or bedding layer of mortar CM (1:4) 15 mm thick for laying floor finishes

M & L 25mm thick Cement concrete type B-0, 1:2:4 (20mm graded aggregate)

M & L 75mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate)

M & L For Glazed ceramic Coloured tiles in vertical surface 350x 250x 7mm / 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 10mm Backing Coat In CM (1:3)

M & L 75mm thick Plinth Protection PCC (1:3:6) type C1 using 20mm graded aggregate (0.6 m wide).

M&L for Hardcore of guage n exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface

S & F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets 10 ltr

S & F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

S & F 110mm PVC (SWR) WC connector bent type

S & F Stop valves, cast copper alloy, Screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long shank and cup (concealed type) 15mm

S & F PVC connections 15mm size with PTMT nuts of length 600mm

S & F Fancy Type C.P. Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

S & F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Health faucet fixing in pipe etc. complete

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)

S & F Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms)

S & F Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms)

S & F Unplasticised PVC pipes of pressure rating 10 kgf/cSqm fixed complete to walls, ceilings or in Floors etc., any type of pipe 32mm dia

S & F Vitreous Cliina wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and orcelain stopper but including brackets

S & F Fancy Type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed

S & F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden /plastic cleats(Minimum weight 190gms)

S & F Soap dish, vitreous China white, approximate size 160x 160x90mm

M&L for 1000 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified

S & F 25 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S & F PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls 110mm

S & F PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors 110mm

S & F PVC (SWR) vent cowl 110mm

S & F PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls 75mm

M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S & F PVC (SWR) pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm

S & F PVC (SWR) branch piece 110mm single (single Y) equal or unequal

S & F PVC (SWR) bends any radius 75mm with access door

M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm

S&F Roof trusses (framed) trusses purlins and fastening (etc.,angle, channel,tubular section,round pipe) or flat section including distance pieces, MS plates/ gusset plates, cleats, hold fast etc. conforming to Gde of steel Fe 410-0 or Fe 310-0 complete all as specified and directed.

S &F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering / cladding to wall, fixed with L or J hooks all as specified and directed.

S & F CPVC pipe SDR 11 and plain cpvc SDR 11 fittings (Concealed /open as directed), and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. Note :- The pipe line shall be concealed from inside and shall be exposed on walls on external faces

M & L for RCC NP3, 150 mm dia pipes laid on 150 mm thick bed with excavation in any type of soil including manholes drop manhole of standard size made of Brick masonry/RCC/ Precast RCC with SFRC Ventilating coverand frame includes all items and aactivities to execute and make sewer line functional fordepth 0.70 m to 1.65 m.

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts, wells,cesspits, man holes, pier holes etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/ loose soil.

M & L for cement concrete in foundations filling and mass concrete type D2 1:4:8 complete all as specified

M&L for Pre-cast cement concrete block masonry (Type C1, 1:3:6, 20mm aggregate) with solid blocks, exc. 10cm in width and setting in mortar, complete all as specified and directed.

M&L, RCC in M25 (20 mm graded aggregate) for Beams, cantilevers, bresummers, lintels over 1.5 m span etc all as specified and as directed

M&L for Formwork to sides and soffits of floor, beam lintels, cantilevers, shelves including supports, etc. also splays between floors and beams, etc. all as specified & all as directed by Engr-in-Charge

M&L TMT bars 5 mm dia & over upto & including 10 mm dia in stirrups, spacers & binders etc all as specified & as directed

M&L TMT bars 10 mm dia & over cut to length, bent to shape required including cranking bending spirally for hooping for column, hooking ends & binding with & including mild steel wire (not less than 0.9 mm dia) or securing with clips quality conforming all as specified & as directed

M&L for 10 mm thick rendering on surfaces other than fair faces of brick/concrete surfaces in CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for prepartion of new plastered surfaces on walls and applying two coats cement based paint on over one coat of primer with alkali resistant priming paint on walls all as specified and directed by the Engr-in-Charge

M & L for cement concrete in foundations filling and mass concrete type C2 1:3:6 complete all as specified and directed.

S&F mild steel for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) ., and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S&F in repairs galvanized, 2 strand, mild steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

S&F of GI base Concertina Razor wire coil of 800 mm dia and fixed to MS Angles all as directed by Engr-In-Charge.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide all as specified and directed.

M&L for PCC 1:2:4 type B0-(using 12.50mm graded stone aggregate) as in coping including necessary form work complete all as specified and directed.

Site Clearance and cutting to shurbs, vegetation etc and disposal of rubbish up to a distance of 50m outside the periphery of area.

Returning ,filling in ,including ,spreading , levelling , watering and well ramming in layers n, exc, 15 cm complete all as specified

Removing excavated material exc1.5 km and n.exc 5.0 KM depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified.

Excavating in post holes in soft/loose soil each not exc. 0.50 cum getting out.

Supply only chain link mild steel galvanized fencing of any size and type.

Fixing only chain link fencing including line wire, any mesh size and type to any type of standard rails, straining bolt etc.

S/F mild steel (5 to 10mm dia of neck) screw bolt (machine made) exc 5cm but not exc 10 cm in length with hexagonal or square head at one end and screwed the other each screw end to be fitted with washer 3 mm thick mild steel.

M/L round bars 10mm dia and over cut to length, bent to shape including cranking, binding spirally for hooping for columns hooking ends and binding with end including mild steel wire (annealed) not less than 0.9mm dia.

M&L for point wiring with 1.5 Sqmm PVC insulated sheathed fire retardant (FR) cable with multithreaded copper conductor cable in and including heavy duty 20 mm dia ISI marked concealed PVC conduit with all accessories for one light/fan point controlled by one switch with 1.25mm thick Metal boxes concealed in wall duly painted with one coat of primer and two coat of black bituminous paint ,sleek mounting plates for fixing switches regulator and including 1.5 Sqmm stranded copper conductor earth wire connected to common earth and dully complete all as specified. NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes/PVC conduit to required depth & making good the disturbed surface in CM 1:4 including finishing the surface to match with the existing surface.

(a) One light point controlled by one way one switch SP 5 Amps ,240 V.

(b) One exhaust fan point controlled by one way one switch SP 5 Amps, 240 V.

(c) One switch socket outlet 3 Pin, 5 Amps, SP on independent board.

(d) One switch socket outlet 3 Pin, 5 Amps, SP on same board.

All as per the above item No 1 herein before but with 2.5 Sqmm cable for 3 Pin 5/15 Amps switch socket outlet.

S&F switch piano flush type single pole one way 6 Amps 240V grade ISI marked.

S&F switch piano flush type single pole two way 240V grade ISI marked .

S&F socket outlet 2 in 1, 3 Pin , 6 Amps flush type ISI marked.

S&F socket outlet non inter locking type 3 pin ,16 Amps flush type ISI marked.

S&F switch piano flush type single pole one way 16 Amps 240V grade ISI marked.

S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked complete

Supply and fixing LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting upto PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit including as per site requirement and 2 Nos of round or square PVC bolck for fixing of FTL fitting complete all as per directed by Engr-in-charge.

Supply and fixing of mirror light of capacity 1x10 Watt epoxy white powder coated CRCA sheet steel housing with acrylic diffuser gaskat with all fixing acessories complete all as specified and directed.

S&F sheet metal enclosures for distribution board when MCB to be used SPN ( Single pole and neutral ) 12 way, 240 Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed.

Supply & fix RCBOs double pole 40A for earth leakage, overload & short- circuit protection 30 mA complete

S&F MCB SP, 5 to 32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series complete.

supply and fix AC surge protection device, one pole & neutral, Voltage 240V DIN rail mounted,electrical conncetion with suitable rating copper wire complete all as specified and directed by Engr-in-charge.

supply and fixing under voltage & over voltage protection ,DIN rail mounted,single phase electrical conncetion with suitable rating copper wirecomplete all as specified and directed by Engr-in-charge.

M&L , earthing complete for machinary / Equipment installed at power house / sub station with galavanised steel earth plate electrode of size 60 cmx 60 cmx 6 mm thick buried directly in ground ( earth pit not less then 2.25 m deep below the normal ground level ) with top edge of the earth plate not less then 1.5m below normal Ground level connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washerws and check nuts all shown in electrical plate No.5 of SSR Part- I connected to main board / disribution board complete .Earthing GI lead and GI protection pipe 15 mm dia light grade upto 7.5 m from earth pit connecting to machinary/ equipment, testing point, all as specified and testing on completion all as per directed.

Note :- (i) The unit rate shall also included for earth work in hard /dense soil , PCC type C-I (1:3:6) chamber , PCC 1:2:4 type B-I cover 50 mm thick reinforced with 8 mm dia TMT bars,150 mm c/c both ways, funnel with watering pipe 20 mm dia medium graded , GI protection pipe light grade 15 mm dia and wire mesh complete in addition to items No. 1(a) to (e) of preamble (notes) under sub heading earthing specified on SI page No. 389 of SSR Part - II.

(ii) Earthing lead and GI protection pipe beyond 7.5 mtrs will be measured and paid separatelly if required under appropriate Schedule.

Note :- (i) Earthing shall be tested as specified in casul 19.137 of SSP PART - I 2009 , to the entire satisfication of Engr-in-Charge. (ii) On teting after complataion of earthing , if the desired earth resistance is not obatined the earthing wiil be re done by the contractor at his on risk and cost to the entire satisfaction of the Engr - in - charge.

S&f angle holder backlite with 1x11 Watt LED Bulb with fixed on hylum sheet including all fixing acessories and making of connection with twin core flexible copper conductor from ceiling rose to fitting complete all as specified and directed.

Supply and fix exhaust fan, Plastic body AC single Phase. 230V of size 300 m sweep with, blades, and frame and louvers complete.

Supply and fix in replacement XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of cross sectional area 16 sqmm 2 core complete all as specified and directed

Excavation in trenches in soft/loose soil , not.exc 1.5 mtr wide and not.exc 1.5 mtr deep and getting out in soft/loose soil for laying of cable/foundation of pole and stay etc in complete as sepecified.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm.

Removing excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above ground level from starting point.

M&L for sand cushioning in trenches for protection of LT under ground cable including watering and consolidation.

Supplying and laying un-reinforced precast concrete cable cover class LV Type 1, flat, size 250mm x 150mm x 40mm complete.

Supply and laying GI tube light grade 40 mm bore complete.

Supply and lay pipe uPVC pipe including fittings of size 50 mm (2.0") dia complete all as specified and directed

Supply and lay pipe uPVC pipe including fittings of size 25 mm (1.0") dia complete all as specified and directed

M&L for cutting of existing DI/CI pipe line in position for rectifying leakage and reducing to required length, in position, for insertion of collars or other fittings including necessory exvation and earthwork, dewatering etc,if any involed, complete all as specified and directed for 50 / 100 mm bore of pipes

supply and fix ball valve 25 mm dia including all fittings all as specfied and directed

Supply and fixing LED flood light 45 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed

NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.

M/s Bombay Novelty Stores

machine vision plus

zotabrothers