Construction of PHC building at Budhal Block Budhal New, District Rajouri

Rendering of service for Architectural drawings, structural Design drawings, other drawings needed at site for the construction of PHC at Budhal Block budhal district Rajouri as per latest Indian standard codes and vetting of structural drawings from govt. approved institutes IIT/NIT/DIQC. (as per the directions of PWD(R&B) deptt.) (The contractor shall supply 5(five) sets of hard copy and 1 (one) set of soft copy of each drawings. 3 (three) sets of drawings shall be supplied in A1 size and 2(two) sets in A3 size. All Drawing shall be prepared on CAD.

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) Crushed .

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with.1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Stone filling hand packed in horizontal level including cost of stones

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement-All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size)

Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V level

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.All works upto plinth level in 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) crushed. Using 20% boulder.

Reinforcement for RCC work including straightening cutting, bending, placing in position & binding all complete with TMT bars.

Centring and Shuttering including strutting, propping etc and removal of form work for

Foundations: footings, bases of columns etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and centilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Suspended floors, roofs, landings, balconies and access platform.

Edges of slabs and breaks in floors and walls

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1 :6 ( 1 cement : 6 coarse sand) .

Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1 :6 ( 1 cement : 6 coarse sand) & Extra for brick work in superstructure above plinth level upto floor V level. (By manual means)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) Sal wood

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete fixed to steel windows by welding.

6 mm Cement plaster to ceiling of mix 1 : 3 ( 1 cement : 3 fine sand)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.21.1 With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws:30mm

Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg/sqm (4mm thick) float glass panes including lSI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 30mm thick second class Kail wood

Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average width for aperture 1.4 mm in both directoin with wire of dia. 0.63 mm for doors, windows and clerestory windows with hinges and necessary screws lSI marked M.S. pressed bright finished butt hinges with necessary screws of required size. 30 mm thick Second class kail wood.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 5.0 mm thick glass pane (weighing not less than 12.50 kg/sqm)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angles 40x40x6mm for diagonal braces

Providing and fixing lSI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete 250x16 mm

Providing and fixing lSI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete.

Providing and fixing lSI marked oxidised M.S. handles conforming to IS : 4992 with necessary screws etc.complete:

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20 mm nominal size stone aggregate.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 60x60cm

Providing and fixing 1st quality ceramic glazed floor tiles conformingtoIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in Charge. 16.90.1 18 mm thick

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic washable distemper (ready made) of approved manufacturer and of required shade/ colour complete as per manufacturer's specifications Two or more coats on new work

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. Crushed

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete (welded) with all fixture

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.5 mm thick with zinc coating not less than 350 gram/m2

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.0.50 mm thick with zinc coating not less than 275 gram/m2.

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) :

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position :Budloo / Fir wood

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendic

ular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing 4mm ACP SHEET

Carriage of material from source to site by Mechanical transport

Sand for an average distance of 175 kms by MT

Stone Aggregate below 40mm for an average distance of 20 kms by MT

Stone Aggregate below 20mm for an average distance of 20 kms by MT

Bricks for an average distance of 175 kmsby MT

Stone for an average distance of 5 kms by MT

Providing and fixing water closet squatting pan ( Indiantype W.C. pan) with 100 mm sand cast Iron P or Strap,10 litre low level P.V. C. flushing cistern including flushpipe (of approved make) "manually contro(led device(handle lever) conforming to IS:7231, with all fittings andfixtures complete, including cutting and making goodthe walls and floors wherever required Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: 18.4.1 One urinal basin with 5 literwhite P.V.C automatic flushing cistern.

Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. centre hole mixture, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China wash basin size 630x450 mm of make Hindware/Cera/Jaquar or as approved by site incharge

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of make Hindware/Cera/Jaquar or as approved by site incharge

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink including waste coupling as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fitting sand brackets, cutting and making good the walls wherever required 510x1040mm bowl depth 250mm

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 32 mm dia

Providing and fixing 100 mm CP grating for gully, floor or Nahani trap.

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic . moulded frame of approved make and shade with 6 mm thick hard Rectangular shape 453x357 mm

Providing and fixing PVC pipes with necessary stays / clamps with fasteners of following dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent

160 mm dia (NSI)

110 mm dia (NSI)

75 mm dia (NSI)

Providing and fixing PVC door bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete:

160 mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

110 mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

75 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

Providing and fixing PVC plain bend of required degree:

160 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (

110 mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

100 mm dia. working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

Providing and fixing PVC door Tee with PVC acess door, insertion rubber washer 3 mm thick, bolts and nuts complete.

110x110x110mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

75x75x75mm dia working pressure 4kg/cm2. (NSI)

Providing and fixing PVC Plain reducer tee insertion rubber washer 3 mm thick, bolts and nuts complete.

110x110x75mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

Providing and fixing PVC offsets working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

75 mm PVC off sets (NSI)

110 mm PVC off sets. (NSI)

160 mm PVC off sets. (NSI)

Providing and fixing PVC collar:

110mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

75mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

160mm dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent. (NSI)

Providing and fixing PVC P/S/F trap of different dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent complete, including cost of cutting and making good the walls and floors: (NSI)

Cutting chases in brick masonry walls for following diameter PVC pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 12.5mm nominal size) 1:4 ( 1 cement: 4 coarse sand)

100mm dia.

75mm dia.

Providing & fixing PVC Cowl of make Supreme, finolex or equivalent

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc. (Internal work) of make Jindal/Surya Prakash of medium class or as approved by site incharge

15 mm dia. nominal bore (medium)

20 mm dia. nominal bore (medium)

25 mm dia. nominal bore (medium)

32 mm dia. nominal bore (medium)

Providing and fixing G.l. pipes complete with G.l. fittings including trenching and refilling etc. (external work) of make Jindal/Surya Prakash of medium class or as approved by site incharge

25 mm dia. nominal bore

Providing & fixing Brass ball valve of approved quality conforming to IS : 8931 of 15mm nominal bore of make DRP or as approved by site incharge

Providing & fixing Brass ball valve of approved quality conforming to IS : 8931 of 25mm nominal bore of make DRP or as approved by site incharge

Providing & fixing Brass ball valve of approved quality conforming to IS : 8931 of 20mm nominal bore of make DRP or as approved by site incharge

Providing and fixing C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design

Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With F.P.S. bricks with class designation 75 & with Crushed stone aggregate

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G. I. pipe etc.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement: 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

Cutting holes up to 30x30 em in walls including making good the same With common burnt clay F.P.S. (non modular) bricks

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround pvc pipes including bed concrete as per standard design

100 mm diameter S.W. pipe (a) Crushed

150 mm diameter S.W. pipe (a) Crushed

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing installation and testing of geysor of approved quality and manufacture venus/Bajaj or equivalent all complete ,(35 ltr capacity). (NSI)

Providing and installation of two nos 2HP three phase pump of make crompton with electrical connection. (NSI)

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 18.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge.

Solar Photo Voltaic Power Generation system

Supply, installation,testing and commissioning of grid interactive roof top solar photo voltaic power generation system including space frame.