SPECIAL REPAIR TO SITE 22 23 24 DPP AND T 166 AT 2208 SQN AT AF STN NALIYA

Amount

Excavation in trenches n exc 1.50M wide and n exc 1.50M deep and getting out any type of soil complete all as specified & directed.

Demolition of cement concrete(unreinforced) in ground floors and paving n exc 15 cm thickness complete all as specified & directed.

Demolition of reineforced cement concrete of any description and any position not otherwise specifically provide for complete all as specified & directed.

Demolition of RCC, roofs (other than ), beams staircases, landing, chajjas and similar complete all as specified & directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Complete removal of existing water proofing treatment from top of roof and canopies/ chajjas of buildings including removal of plaster/ loose concrete and removing the debris outside of MD land and earthing strip, electric cable. (Refixing earthing strip and cable at the same place after execution of APP) complete all as specified and directed.

Taking down chowkhats or frames with shutters n.exc.1.5 sqm (Without taking off shutters from the frame) and removing to or from store complete all as specified & directed.

Taking down chowkhats or frames with shutters exc.1.5 sqm but N.exc 4 Sqm (without taking off shutters from the frame) and removing to or from store complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding; removing serviceable tiles to store and rubbish off the premises complete all as specified & directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M & L providing and injecting chemical imulsion for post constructional anti termite treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12mm dia holes up to 300mm deep and 300 centre to centre including pluging holes complete all as specified and as directed.

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment alongwith external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified & directed.

M & L for providing and injecting chemical emulsion for post Constructional Anti-termite Treatment at point of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litres per hole by drilling 6mm dia hole at a down word angle of 45 degrees at 150mm center to center and sealing the same complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 by using 40mm graded crushed broken stone aggregate as in foundations filling & mass concrete complete all as specified & directed.

S&F Formwork to sides of concrete foundations, footings, bases of columns, sides and soffits of foundations and plinth beams and similar work vertical or batter complete all as specified & directed.

S&F Formwork to sides and soffits of floor or roof beams, lintels, cantilevers etc complete all as specified & directed.

S&F Formwork to sides of pillars , posts, struts, piers, columns etc complete all as specified & directed.

S&F Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) complete all as specified & directed.

M&L for RCC M-30 Gde design mix concrete using 20mm graded aggregate to col footings and plinth beams, bases of columns etc complete all as specified & directed.

M&L RCC M-30 Gde design mix concrete using 20mm graded aggregate to columns, pillars, posts etc complete all as specified & directed.

M&L RCC M-30 Gde design mix concrete using 20mm graded aggregate to slabs supported on walls,beams and column in floor, roofs, landing, balcony, deck slab complete all as specified and as directed.

M&L RCC M-30 Gde design mix concrete using 20mm graded aggregate to Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for Rendering 10mm thick cement plaster in CM 1:3 on roof slab/canopies/ chajjas with water proofing compound @ 3 % of weight of cement and making plastered surfaces to receive water proofing treatment (finished fair and even) complete all as specified and as directed. (Note:- water proofing compound will be measured and paid for seperately as supply only)

M & L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

M&L for Providing, cement concrete (1:2:4) Type B-0 (using 12.50mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edge complete all as specified and as directed.

M&L for preparing, clean and dry plastered roof surfaces and applying APP modified water proofing membrane with non woven polyster reinforcement/mat not less than 3mm thick having weight not less than 3kg/Sqm over a coat of bitumenous filler/ primer conforming to IS 3384-1986 and applying @ 250gm/ Sqm through approved applicator and applying all as per manufacturers instructions complete all as specified and as directed.

M&L for repairs to structural members like columns, beams, slab by removing the corrosion from reinfrocement and applying one coat of nito zinc primer or equivalent to renforcement and applying one coat of NITOBOND SBR or equivalent to old concerete and applying cement concrete 1:1.5:3 using 6mm aggregate and approved Fosroc or equivalent chemical for additional strength including necessary formwork as required the thickness of concrete is 15mm to 50mm complete all as specified & directed. (Nitobond EP & Nitobond SBR)

S&F second class hard wood plain, solid straight factory made chowkats or frames wrought framed, rebated on solid rounded or chamfered put together with glue pinned incl tarring back of chowkhat/frame complete all as specified & directed.

S&F to chowkats or frames 2nd class hard wood glazed and skeleton shutters 35mm thick factory made open rebated and prepare to receive glass gauges etc edges of framing plain or chamfered or rounded fitted with cut beads for securing glass or gauges etc complete all as specified & directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified & directed.

S&F, factory made solid panel PVC door shutters, 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' chanel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either sides & as gap insert for top & bottom rails. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed stiles & rails with suitable PVC sheet beading and jointed together with solvent cement. Supply and fixing in the frame at site as per specification and drawing complete all as specified & directed.

S&F powder coated aluminium, three track sliding window frame of section size 92.00x 31.75x1.3mm comprising of one No of fly proof shutter and two nos of glazed shutter frames of section size 40x18x1.3mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement all as specified and directed. (Notes. (i) Glass filling in panels of window and aluminium wire mesh/wire cloth shall be demed to be included in the quoted rate for the time, ii) aluminium alloy wire cloth in panels of white gauzed shutter shall be 0.45mm nominal dia of wire and avg width of aperture 1.40mm, fixed with aluminium wire staples. iii) Glass filling in panels of glazed shutter shall be 4mm thick tinet sheet glass (shade/tint) complete all as specified & directed.

S&F anodised aluminium grill made out of 7mm x 4.5mm wide flat, square ractangular or similar section, fixed with channel of size 38mm x 12mm x 13mm (section 8778 complete all as specified (make: DECO GRILL No. DG 102 with aperture- 80mm or equipment as approved by GE).

S&F powder coated aluminium doors of section and partition with frame shutters.incl necessary joining cleats, glazing cleats, rubber paking gasket and lining, anodised aluminium snap beading, screws, handles and locking arrangement.

S&F 19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified & directed.

M & L for Cutting/opening out cracks to in existing wall surfaces, cleaning loose material, filling with crack fillers and finishing the surface to match the existing surface complete all as specified and as directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple complete all as specified & directed.

S & F venetian blinds of size according to window and confirming to IS 1826:1961 of approved colour and make complete all as specified and as directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, dark shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry incl screed bed 15mm thick in CM 1:6 and pointed in white or coloured cement to match complete all as specified & directed.

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles complete all as specified and directed.

S & F Aluminium handles cast type, annodised 150 mm size complete all as specified & directed.

S&F 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sectiopns and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & directed.

S & F 150 mm long alluminium, anodised barrel tower bolts extruded section and fixed complete all as specified & directed.

S& F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified & directed.

Sheet glass, 5.0 mm thick ordinary quality and glazing with oil putty in squares n exc 0.50 sq.m in each pane complete all as specified and as directed.

Dismantling structural steel work including doors, gates, rolling shutters, etc. but excluding framed truss etc.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and gaides) and hanging, also fastening and fixing complet of FE - 410W complete all as specified & directed.

M & L for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified & directed.

M& L Mild steel, corrugated, black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L for plain cement concrete 75mm thick type C-1 1:3:6 (using 20mm graded stone aggregae as in path,plinth protection or hardstanding complete all as specified.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Description all as srl Item No. 52 here-in-before but 6mm to 8mm dia

Description all as srl Item No. 52 here-in-before 5mm dia and over upto and including 10mm dia in stirrups spacers and binders complete all as specified and directed.

Welding in repairs n. exc 2.5cm in length for exc 09 mm not exceeding 20 mm bars

M&L Precast cement concrete solid block masonry exc.10 cm in width and setting in mortar complete type C-1 1:3:6 (by using 20mm graded aggregate) in 1:6 CM complete all as specified and directed.

Supply only integral water proofing compound

M&L for rendering 15mm thick cement plaster in CM 1:4 on fair faces of brick work or concrete surfaces with water proofing compound @ 3 % of weight of cement and finished fair and smooth without using extra cement complete all as specified and as directed. (Note:- water proofing compound will be measured and paid for seperately as supply only)

M&L for rendering 15mm thick cement plaster in CM 1:6 on other than fair faces of brick work or concrete surfaces finished fair and smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 10mm thick cement plaster in CM 1:3 on ceiling surface finished fair and smooth without using extra cement complete all as specified and as directed.

M&L for Preparing surfaces plastered or unplastered and applying three coats of white wash on ceilings complete all as specified and as directed.

M&L for Preparing surfaces plastered or unplastered and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance, dirt resistance exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new/ old surfaces complete all as specified and as directed.

M & L preparation of old surfaces of wall incl complete removal of existing treatment and applying two coats of oil bound distember complete all as specified and directed.

M & L preparation of old surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M & L preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Rendering 10mm thick cement plaster (1:6) on fair faces of brick or concrete surfaces complete all as specified and directed.

M&L for two coat of synthetic enamel paint over a coat of primer red oxide including preparation of new surface of any description over 10 cm in width and girth not otherwise described complete all as specified and directed.

S&F tube 15mm bore medium grade, galvanised with all fittings and fixed complete to walls and ceilling or laid in floors including taking down or up steel tubing complete all as specified and directed.

S&F in repair bib taps 15 mm dia cromium plated fancy type with crutch or butterfly handle screwed down and fixed in repairs complete all as specified and directed.

S & F in repairs stop valve cast copper alloy chromium platted screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes 15 mm dia complete all as specified and directed.

S& F in repairs 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly- nuts, screwed for iron pipe complete all as specified and directed.

S & F in repairs PVC Connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Returning filling including spreading levelling watering and well ramming in layers n exc 25 cm in hard dense soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Removal of demolished materials to distance exc 1.50 km and not exc 5.00km complete all as specified and directed.

Taking down carefully point wiring complete of any type (batten / surface conduit for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces complete all as specified and directed.

Taking down carefully by unscrewing from boards/outlet boxes, DBs with MCBs complete all as specified & directed.

M&L for point wiring for one light/Fan/socket 5Amps point on indep board controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn through and including heavy duty ERW conduit not less than 20 mm dia concealed type , including all accessories like bend, tees, junction boxes etc. including 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly complete all as specified and directed. Note : Point wiring will be done from Main DB. Length of point wiring may be beyond 5 mtrs and no extra amount for long point wiring will be paid to contractor.

S&F in repair/replacement of flame proof, weather proof type, distribution board, Aluminum die cast alloy in LM6 material sheet metal enclosure including MCB 63 Amp TPN (incomer) and 07 Nos SP 6-32 Amps (out going), terminal, wiring and all fitting accessories etc complete all as specified and as directed.

S& F in repair/replacement of LED flame proof well glass in die cast aluminum housing with heat resistant toughened glass, 70watt , IP65 protected and including all accessories, connecting up with flexible copper conductor 1.5 Sqmm 3core covered with flexible metal conduit of suitable size complete all as specified and directed.

S&F in replacement of switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed.

S&F in replacement of Flame proof switch socket & plug combined in LM6 cable termination box in LM6,16A, 250V, 2P+earth complete all as specified and directed

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground earth pit with adequate quantity of charcoal and dust and common salt, not less than 2.25 mtr deep below ground level connected to & using galvanised iron strip 25×4mm as earthing lead drawn through GI protection pipe of size ordered specified for protection of earthing lead from earth electrode to test point/main DB from mechanical injury or tempering by means of nuts and bolt check nuts and washers of galvanised iron sheet all as shown in electrical plate No 5 of SSR Part - I and connected to earthing test point complete including testing filling of adequate quantity of charcoal dust and common salt including refilling earth and removal of surplus soil upto 50 mtrs PCC 1:3:6 type CI chamber precast RCC cover 40 mm thick reinforced with 6 mm dia MS bar 3 Nos both way with handle made out of 6 mm dia MS bar water pipe with wire mesh and connecting with earth point testing etc complete all as specified and directed.

Venus Engineering

NILESH SUBHASH KARALE

NEELKANTHA ASSOCIATE

Laxmi Enterprise

GEE CEE ENTERPRISES

S and G Construction

NAVIN K LAKHANI

baghela construction