RequiredExperience with Government
RequiredAnnual Turnover
RequiredCertificate (Requested in ATC)
RequiredOEM Authorization Certificate
RequiredOEM Annual Turnover Bid to RA enabled Yes Track Suits - Sports ( 11 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * MATERIAL Fabric ( Composition ) Polyester Polyester 1/8 Percentage of Blending ( in case of Blended Fabric ) Not Applicable Not Applicable Mass ( gram per square mtrs ) 300 300.0 Fabric Construction Knitted Knitted Weave ( In case of Woven Fabric ) Not Applicable Not Applicable Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Plain ( Single Jersey ) Knitted
RequiredPlain ( Single Jersey ) Knitted
RequiredEnds per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric Yes Yes Upper Lining Yes Yes Lower Lining Yes Yes Lining Material 100% Polyester Mesh 100% Polyester Mesh Mass of Lining (Gram per Square Meter) 65 * Netting mesh No of holes on base & bias within 625 Square millimeter 155 * Technical Requirements of Slide Fastener for Upper Closing No No Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) No No Slide Fastners are BIS Marked Not Applicable Not Applicable Width of Tape Elastic at Waist of Trouser 3.5 cm * Width of Tape Elastic at 3.5 cm * 2/8 Bottom of Upper Technical Requirements of Waist Band Waist band as per IS 9686- 1980 latest Waist band as per IS 9686- 1980 latest Waist Draw Cord Polypropylene Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping Yes Yes Lower provided with Piping Yes Yes Piping Fabric- Composition 100 percent Polyester * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) 130 130 Embroidery Thread Rayon Rayon SIZE Size Medium (M) Medium (M) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 52.5 cm ( Medium ) * Width Across Bottom Opening (relaxed) 46 cm ( Medium ) * Length at front from top of collar to bottom 66 cm ( Medium ) * Sleeve length (from center of back to bottom of sleeve 84.5 cm ( Medium ) * Sleeve opening relaxed ( Cuff ) Width 10 * Front Neck Drop 9 * Back Neck Drop 1.2 * Length of Slide Fastener 64 cm( Medium ) * DIMENSIONS OF LOWER Side Seam Length 104.5 cm ( Medium ) * Waist relaxed ( Width Across ) 43 cm ( Medium ) * Waist stretched (Width 52.5 cm ( Medium ) * 3/8 Across ) Seat/Hip ( 15 cm below waist band) 52.5 cm ( Medium ) * Thigh (at Crotch) ( Width Across ) 36 cm ( Medium ) * Bottom Opening ( Width Across ) 22 * Front rise including waist band 28 cm ( Medium ) * Back rise including waist band 38 cm ( Medium ) * Length of Waist Tying Cord 160 * Bottom Fold (Hem) with full turn in(cm) 1.5 * POCKETS Number of Pockets (Upper) 2 Side Pockets and one Inside Pocket at Chest 2 Side Pockets and one Inside Pocket at Chest Size of Side Pockets- Upper ( Length X Width ) ( cm ) 17 cm X 18 cm * Size of Inside Pocket at Chest- Upper 11 cm X 15 cm * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper Yes Yes Number of Pockets (Lower) 2 Side Pockets and 1 Back Pocket 2 Side Pockets and 1 Back Pocket Size of Side Pockets - Lower ( Length X Width ) ( cm ) 17 cm X 18 cm * Side Pocket Opening- Lower 15 * Pocket Closure with Slide Fastener - Lower Side Pockets with Slide Fastener Side Pockets with Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement With Canvas Reinforcement * SLEEVE Sleeve Type Reglan Sleeve * PIPING Position and Dimensions of Piping - * 4/8 on Upper Position and Dimensions of Piping on Lower - * STITCHING Sewing Thread 145 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in single rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in single rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in single rows with chain stitch on the elastic * Lining seams Inverted * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas Pocket opening
RequiredCentre of Waist Band Seam and bottom hem and other stress bearing areas * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Multicolour Contrasting Pannels Any other colour as per buyer's requirements * Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * 5/8 Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Any other colour as per buyer's requirements Any other colour as per buyer's requirements Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to perspiration ( IS 971 )- Mesh Lining 4 * Colour of Piping Material Any other colour as per buyer's requirements * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 3 3 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements Type of Logo Printed Printed Number of Logos on Upper 2 2 Number of Logos on Lower Not Applicable Not Applicable Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Government Lab to prove conformity of products to the No No 6/8 specification Test Report No - * Test Report Date - * Name of the Lab - * Address of the Lab - * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Not applicable * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes * Bold specifications are the golden parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
