SPECIAL REPAIR TO CERTAIN SMQs AND PROVN OF MISC B/R AND E/M WORKS OF 308 TRU AT AF STATION BHUJ

Taking down cement plaster of any description on brick walls , cement surfaces including raking out joints hacking for key secrubing down with water remove dust, debries/rubbish etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces including finished even and smooth without using extra cement. complete all as specified and directed by Engineer-in-Charge

Material & labour for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:6 and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge

Material & labour for rendering 15mm thick in Cement Mortar 1:4 (External) on brick walls or on concrete surfaces in two coats, 1st coat of 10mm thick and 2nd coat of 5mm thick including mixing with WPC to 2nd coat as per manufacturer's instructions, plastered surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE : Integral water proofing compound shall be Measured and paid separately as ‘Supply only’ under relevant Items.

Supply only integral water proofing compound ISI marked complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion, white or tinted including one coat of wall primer by finishing the surfaces even and smooth complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new or previously untreated concrete or PCC block masonry external surfaces and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old treated surfaces of wall including brooming down, scrapping down smoke soots etc. and appying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old treated surfaces of ceiling including brooming down, scrapping down smoke soots etc. and appying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old treated surfaces of wall surfaces and applying one coat of distemper with distemper oil emulsion white or tinted complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparation of old treated wall surfaces including brooming down and applying one coat of exterior emulsion paint complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old wooden painted surfaces of any description exc 10 cm width or girth and appying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25mm thick cement concrete type BO 1:2:4 using 12.5mm graded stone aggregate in sub base floors complete all as specified and directed by Engineer-in-Charge.

Material & labour for mat finish coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per item No 16.00 but on vertical surfaces such as in skirting and dados laid over plaster ijn CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & labour for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material & labour for glazed ceramic coloured tiles in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over plaster in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs 25 mm bore stainless steel heavy duty drapery rod (curtain rod) including all fittings and fixers , cut to length and fix in position including decorative type finals (bracket) colored finish, of approved pattern by GE complete all as specified and directed by Engineer-in-Charge.

Taking up on down steel tubing and connection incl cleaning for refining of the following bore of pipe complete all as specified and directed by Engineer-in-Charge of following size :-

15mm bore

20mm bore

Supply & fix CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls and ceilings or laid in floors of complete all as specified and directed by Engineer-in-Charge of following size :-(SDR-13.5 )

15mm nominal dia of pipe

20mm nominal dia of pipe

Dismantling of cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer-in-Charge following bore of pipe

100/110mm dia

75 mm dia

Supply & fix PVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors complete all as specified and directed by Engineer-in-Charge of following size :-

110mm dia

75 mm dia

Supply & fix PVC junction single 'Tee' equal with door opening, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following size :-

110mm dia

75 mm dia

Supply & fix PVC sockets equal, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following size :-

110mm dia

75 mm dia

Supply & fix PVC bend equal of any radius with door, ISI marked, IS-14735, jointed with solvent cement for 75mm size pipes complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC bend equal of any radius without door, ISI marked, IS-14735, jointed with solvent cement for 110mm size pipes complete all as specified and directed by Engineer-in-Charge.

Supply & fix stainless steel sink with drainage board, made out of 1 mm thick sheet for kitchen or laboratory with plug washer waste pipe cast iron cantilever brckets connecting union overall size 915mm x 460 mm with bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs stainless steel plate rack made out of 1mm thick stainless steel sheet, overall minimum size 60cm x 90cm and for 6 plates as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 500 ltrs including taking down existing tank also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for grating square 150mmx150mm size of stainless steel complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs vitreous china wash basin, angle back, size 550x400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for pillar taps of 15 mm bore, fancy type with capstan head, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix waste pipe of 32mm dia PVC pipe for WHB with long screwed shanks and fly nut flange end beddedd in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for vitrious china squattin pan ,Orissa Paattern Size 580x440 mm white with integral foot rests ( Excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs PVC low level valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 Ltr capacity complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for size 15mm bore complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs stop valve 15 mm dia cast chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed for size 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for shower rose for 15 mm dia, 125mm long, cast chromium plated screwed down high pressure with long shank screwed end for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC connection 450mm long with check nut for wash hand basin etc complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n exc 1.5 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm complete all as specified and directed by Engineer-in-Charge.

Supply & fix pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock stricke plate etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock stricke plate etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs, mud stops, filling in frames and the like rounded or or chamfered on edges complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/ Gauge etc. Size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete all as specified and directed by Engineer-in-Charge.

Supply & fix stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih SS wire staples complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick 2nd class hard wood factory made plain framed, paneled shutters (any number of panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veveered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

Supply & fix Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed by Engineer-in-Charge.

Supply & fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed by Engineer-in-Charge.

Supply & fix preparing new or previously untreatedsteel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer on steel surfaces complete all as specified and directed by Engineer-in-Charge.

Dismantling old unserviceable kitchen cupbord shutter with frame complete all as specified and directed by Engineer-in-Charge.

Material & labour for prelaminated particle board 18mm thick interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work fixed for cuboards/shelfs/partitons etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix SS plate rack (size- 45 Cm x50 Cm x 20 Cm /4mm dia SS rod)with necessary fitting like slider etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix SS crockery rack (size- 45 Cm x50 Cmx 20 Cm /4 mm dia SS rod with necessary fitting like slider etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix SS bottle rack (size-25 Cm x 50 Cm x 45 Cm/ 4 mm dia SS rod) with necessary fitting like slider etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix self clossing hinges 75 mm long complete all as specified and directed by Engineer-in-Charge.

Supply & fix magnet lock 30 mmm long complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100 long SS fancy type handle complete all as specified and directed by Engineer-in-Charge.

Supply & fix butt hinges 75mm size, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

Supply & fix butt hinges 100mm size, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

Supply & fix 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply & fix aluminium, anodised barrel tower bolt of extruded section and fixed 150mm of size complete all as specified and directed by Engineer-in-Charge.

Supply & fix aluminium, anodised 100mm size of hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer-in-Charge.

Supply & fix floor door stopper of brass body and tongue with hard drawn steel spring, overall length of cover plate 150mm and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

Material & labour for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) complete all as specified and directed by Engineer-in-Charge.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately.

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm complete all as specified and directed by Engineer-in-Charge.

Removing of old water proofing treatment including screed bed and cleaning the surface of slab with wire brushes removing dust, foreign materials including flushing at junction of wall and removing the rubbish off the premises to a distance exc. 500m, complete all as specified and as directed Engr-in-Charge.

Material & labour for 15mm thick rendering in cement mortar 1: 4 on faces of brick work or concrete surfaces with WPC, finished even and smooth W/O using extra cement as in roof complete all as specified and directed by Engineer-in-Charge. (WPC shall be measured & paid seperately) .

Material & labour for water proofing treatment on roof and preparing the surfaces to receive WPT treatment , applying cold bituminous primer @ 0.30 ltr / Sqm conforming to IS 3384 applied on plastered surfaces including side walls , followed by a layers of APP based polymeric membrane reinforced with polyster non woven fabric (weighing 3.5 Kg/Sqm(minimum) and 3 mm thick) with mineral finish laid on primed surface by torch application with side overlap 100 mm and ends over laps 150 mm , joints sealed properly as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.

Material & labour for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed by Engineer-in-Charge.

Removal of damaged concrete along with loose damaged and cracked concrete/cover concrete at ceiling up to beyond the corroded steel reinforcements to a depth of10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer,pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement and removal and disposal of debris within owners premises including all plant and machineries. Note : Rates quoted for all items should include working upto 6m height including all necessary scaffolding , staging etc complete all as specified and directed by Engineer-in-Charge. HSE Guidelines : Recommended to wear tightfitting,dust-resistant goggles and mask during breaking and surface grinding works etc

Material & labour for cleaning as directed & specified all rust/ scales/corrosion from reinforcement bars using rust remover Reebaklens RR- Rust remover, cleaning and etching agent supplied in 1/2, 1 and 5 Litre containers, having Specific Gravity 1.16 - 1.22 @ 25°C. Reebaklens RR cleaning agent is a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear green solution.Application of Reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours followed by cleaning the surface with wire brush and washing surface with fresh water as required to exposed reinforcement bars complete as specified.Note : Rates quoted for all items should include working upto 6m height including all necessary scaffolding , staging etc complete all as specified and directed by Engineer-in-Charge. HSE Guidelines : Recommended to wear tight-fitting, dust-resistant, chemical splash goggles if airborne dust is generated, Wear protective gloves. Wear appropriate clothing to prevent any possibility of skin contact. .

Material & labour for TMT steel bars , Cutting, fabricating new reinforcement Fe500 and fixing with old existing reinforcement which was reduced to 20 % or more of its original diameter as provided in original structure and additional steels as directed by EIC to be fixed with chemical anchor grout Lokfix E55- Styrene free vinyl-ester resin based cartridge system for anchoring reinforcement supplied in 300 ml cartidge with a single mixer nozzle, application inclueds drilling hole close to old reinforcement bar with suitable drill as per dia of bar, cleaning the hole with wire brush and compressed air, putting Lokfix E55 with gun followed by placing rebar with slide rotational motion to avoid air void formation etc complete as directed by EIC.(i) for 8mm dia (min embedment depth 80mm) (ii) for 10mm dia (min embedment depth 90mm) (iii) for 12 mm dia ( min embedment depth 110 mm) (iv) for 16 mm dia ( min embedment depth 125 mm) Note : Rates quoted for all items including all necessary scaffolding , staging etc complete all as specified and as directed. HSE Guidelines : Recommended to wear tight-fitting, dust-resistant, chemical splash goggles if airborne dust is generated, Wear protective gloves. Wear appropriate clothing to prevent any possibility of skin contact.

Material & labour for Epoxy Bond Coat Providing and applying bond coat on the prepared surface to receive polymer modified mortar/polymer modified micro concrete, with two component epoxy based bonding coat Nitobond EP- Epoxy resin concrete bonding agent supplied in 1/2, 1 and 4 Litre packs, having specific gravity 1.15 to 1.2 gm/cc, Compressive strength(BS 6319 Pt.2)- 50 Mpa at 7 days, Flexural strength strength(BS 6319 Pt.3)- 35 Mpa at 7 days, Tensile strength (BS 6319 Pt.7)- 20 Mpa at 7 days, Shear Strength (BS 6319 Pt.4)- 10 Mpa at 7 days, having an over lay time of 6 hrs and 30 ̊C, High bond strenght High bond strength : Bond strength is more than the tensile strength of good quality concrete, Barrier coat : Acts as a ‘barrier coat’ to the migration of chloride ions from host concrete. Laying of reinstatement polymer modified mortar or micro concrete shall be completed within the overlay time of bonding coat. The bond coat act as a bonding coat between old and new concrete. Typical application includes cleaning all loose dust, dirt, grease from host concrete surface by suitable means, mixing both components of bond coat by heavy duty slow speed mixer until a uniform consistency, apply unbroken coat of Nitobond EP with stiff brush covering complete area of patch repair before placing mortar or micro concrete. Item rate is inclusive of materials all labour, tools and tackles,

Material & labour for Polymer modified Mortar-Patch repair (Up to Grade M45) Providing and laying Renderoc SP 40- shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortar supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt.116) -> 20 Mpa at 1 day & > 45 Mpa at 28 days, Tensile Strength(BS 6319 Pt.7) > 2.5 Mpa at 28 Days, Flexural Strength(BS 6319 Pt.3)>7 Mpa at 28 days, Drying shrinkage to ASTM C 157-93, 28 days < 1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25L to 4.5 L, mixed in suitable container with heavy duty slow speed mixer machine to achieve uniform lump free mortar consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slabs, piles etc., where the thickness of application is less than 50 mm in patches as per specification after applying bonding coat. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by Engg.-in-charge.

Pulling down the existing U/S wires of any type from concealed wiring carefully of aluminium point wiring (light, fan, bell, socket, power point etc.) with or without conduit, along with all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator etc complete all as specified and directed by Engineer-in-Charge.

Pulling out sub main wiring only any size of aluminium conductor cable PVC insulated with or without condiut complete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with PVC surface box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

One 3 pin 5 Amp socket outlet on the same board.

One 3 pin 5 Amps socket out let on independent board.

One bell point controlled by one bell push on independent board.

All as per item No.85.00 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps socket out let on independent board complete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through existing conduit including provn of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with new plastic laminated white coloured top sheet cover 3.0 mm thick on existing sunken box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

One 3 pin 5 Amp socket outlet on the same board.

One 3 pin 5 Amps socket out let on independent board.

One bell point controlled by one bell push

All as per item No.87 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps socket out let on independent board complete all as specified and directed by Engineer-in-Charge. .

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor drawn through and including PVC casing caping ISI marked with accessories and 4 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge. Note: Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit)

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 6 Sqmm single core, copper conductor drawn through and including PVC casing caping ISI marked with accessories and 6 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge. Note: Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit)

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor in existing conduit drawn marked with accessories and 4 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge.(Note: Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit)

Supply & fix in replacement energy saving, evironment friendly, long life, corrosion resistent, impact proof, Mini LED building security light made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LEDs with secondary optics and IP 65 protection with LED 20 W light source including material and labour for suitable bracket made of 20 mm dia light grade GI pipe & MS clamps complete with nuts and bolts and washers complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 10 W 2 ft indoor decorative (white) with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 18/20 W 4 ft indoor decorative (white) with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engr-in-Charge

Supply & fixing in replacement of LED Lamp, 7 W ,Type of cap B22, wide operating range 140V -280V, Input current 08mA- 30mA, lumen 180-300, UV and IR free light, color temperature 6500K, cool day light, up to 80 % energy saving over GLS complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 triple pole and neutral 4 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 single pole and neutral 08 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of isolators/MCBs, etc. In distribution board of the following rating and capacities complete all as specified and directed by Engineer-in-Charge of following :-

MCB TPN 415 volts 63 Amps Capacity, 10 KA

MCB SPN of 240 volts 20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Supply & fix in replacement capacitor of capacity 2.5 mfd (PVC Body) suitable for ceiling/exhaust fans/wall mounted fans of any description,any sweep complete all as specified and directed by Engineer-in-charge.

Taking down and refixing ceiling fans/exhaust fan of any sweep any size from site for repair complete all as specified and directed by Engineer-in-charge.

Material & labour for taking out & removing old burnt-out windings of Ceiling fans of any description and rewinding of fan motor with appropriate size super enameled copper wire as approved by Eng-in-charge including insulating material such as illuminous paper,Letherized paper,cotton tape,glass sleeving,insulating varnish ,Bearing ,Bushes,capacitor etc.and transportation to site after testing at workshop,connecting and testing on full load to the entire satisfaction of Eng-in-charge,including painting of fans of any description(ceiling fan/exhaust fan/wall mounte fan/pedestal fan) with applying one coat of synthetic enamel paint(white/Grey) by spray machine including preparation of exisiting decorated surfaces of fans complete all as specified and directed by Engineer-in-charge. .

Material & labour for servicing of 1200/1400MM ceiling fan by dismantling carefully and taking out unserviceable parts, dust & grease, cleaning of internal parts with kerosene oil, washing, checking of alignment of shaft, oiling and re-greasing of bearing/bushes including replacing of unserviceable part like bearing ,gun metal bush, capacitor,Rubber reel of suitable capacity and re-assembling the same and complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of PVC body exhaust fan, AC single phase 230/240V of size 250 mm sweep with louvers including making hole of suitable size/ alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-charge. (Note: Old unserviceable Exhaust Fan will be deposited in MES store yard).

Supply & fix in replacement bell, AC, 230 V, SP, ding dong type complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement stepped type electronic fan Regulator flush type on the existing phenolic laminated etc as reqd single pole 240 volts grade 350 watts heavy duty ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of Ceiling rose 3 phase, PVC/ Polycarbonate body complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 1/2 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 4 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 1 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 2 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 4 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 6 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 8 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular blank plate module 1 complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement, modular switch flush type, 6 Amp. SP, one way ,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6 Amp, flush type 2 module complete all as specified and directed by Engr-in-Charge

Supply & fix in replacement modular swicth, 16 Amp flush type 1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6/16 Amp flush type 2 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular bell push, flush type, 6 Amp,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of ceiling fan regulator modular type electronic step type 5 step 360 deg 120 watt 2 module complete all as specified and directed by Engr-in-Charge.

Material & labour for disconneting electrically and mechanically the existing geyser of any description,any capacity and make/type and in any position for repair/replacement/painting/cleaning etc including disconneting existing cold and hot water pipe connections, strip opening of geyser for descaling of tank element, thermostate,inlet/outlet water pipe connection etc using suitable chemical/wire brush,replacement of unserviceabe parts, re-assembling the same after, repair/descaling, fixing in position including, connecting inlet/outlet water pipe connection, electrical connections any testing of geyser complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement metal plug top 20Amps 3 pin complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement 2.0 KW Electric heating element at site including rubber ring washers ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement for PVC connection with brass nipple 15 mm x 450 mm long for geyser 25/50 ltrs capacity as per sample complete all as specified and directed by Engineer-in-charge.

Surfaces excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out of hard / dense soil.

Removal of excavated soil from site n exc 50 m and depositing wheredirected at a level n exc. 1.5 m above the starting point.

Rolling and consolidating formation surfaces in cutting using power roller exc 8 tonne but n exc 12 tonne

M & L hardcore of gauge n exc 63mm, deposited spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface broken stone or boulders.

M & L PCC 1:3:6 type C2 using 40mm graded aggregates as in sub-base 100 mm thick

M&L for providing 400 micron thick HDPE sheet white/light colour complete all as specified and as directed.

M&L for pavement quality concrete (PQC) of flexural strength 45 Kg/Sqcm in field using minimum 400 Kg of cement/cum of concrete in bays as specified in drgs and adding 0.25% by weight of cement with recron triangular synthetic fibre complete all as specified.

Supply only triangular recron fibre complete all as specified.

Finishing the concrete surface/pavement with wire brush while concrete is green complete all as specified.

M&L for forming Contraction (Dummy) joints 65mm deep x 10mm wide,filled with sealing compound Grade B.

M&L Moorum spread, watered rolled and consolidated to gradient and camber required, spread thickness 100mm as in road side berms as light wearing surfaces all as specified and as directed.

M&L for 75 mm thick cement concrete type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base under interlocking tiles.

Material and labour for 25 mm thick sand filling under floor including consolidation complete all as specified all as specified

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade.

Please Enable Macros to View BoQ information