construction work of hightech toilet at nagar palika parishad gauchar

Amount

civil work

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering,lead up to 50 m and lift upto 1.5 m.

Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Reinforced cement concrete work in M-20 Design MIX (or shall be as per structural drg) grade including mixing as specifications (weigh batched machine mixing or otherwise), mechanical vibration, curing, etc complete at all levels, heights and inclinations but excluding cost of reinforcement and centering & shuttering at all heights and levels achieving perfect smooth surface FREE FROM any honeycombing, bulging, any loss of cement slurry with perfect line including making provisions for reinforcement dowels by partial cast and /or leaving some portions of slabs, beams, rafters, columns, etc partially cast to join with other structural members and then complete the casting as per design drawings and directions, all completely finished:

Reinforced cement concrete work in M-20 Design MIX (or shall be as per structural drg) grade including mixing as specifications (weigh batched machine mixing or otherwise), mechanical vibration, curing, etc complete at all levels, heights and inclinations but excluding cost of reinforcement and centering & shuttering at all heights and levels achieving perfect smooth surface FREE FROM any honeycombing, bulging, any loss of cement slurry with perfect line including making provisions for reinforcement dowels by partial cast and /or leaving some portions of slabs, beams, rafters, columns, etc partially cast to join with other structural members and then complete the casting as per design drawings and directions, all completely finished:

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Up to Plinth

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Above Plinth

Centering shuttering including struttings, propping etc. and removal of form work

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centring and Shuttering for Suspended floors, roofs, landings, balconies and access platform

Brick work with modular bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure 1:4 (1 cement : 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix 1: 6 (1 cement: 6 fine sand)

6 mm cement plaster of mix 1:3 (1 cement: 3 fine sand)

Providing and laying Ceramic glazed floor tiles 300x300 mm to be specified by the manufacturer) of 1st qualityconforming to IS : 15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of CementMortar 1:4 (1 Cement : 4 Coarse sand) including pointing the jointswith white cement and matching pigments etc., complete. (Floor )

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (Wall)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 60x60 cm

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angleof section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded orrigidly fixed together by mechanical means, including M.S. pressed butt hinges2.5 mm thick with mortar guards, lock strike-plate and shock absorbers asspecified and applying a coat of approved steel primer after pre-treatment ofthe surface as directed by Engineer-in-charge:

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B,K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred andflash butt welded and sash bars tenoned and riveted, including providing and fixingof hinges, pivots, including priming coat of approved steel primer, but excludingthe cost of other fittings, complete all as per approved design, (sectional weight oF only steel members shall be measured for payment).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)decorative type, core of block board construction with frame of 1st class hard woodand well matched teak 3 ply veneering with vertical grains or cross bands and faceveneers on both faces of shutters.

Providing and fixing 1.5mm thick laminate greenlam ( supertuf or approved equivalent) or approved colour on flush door shutter with adhesive etc. (basic rate of Rs. 1200- per sheet) 250x10 mm

Providing and fixing 1.5mm thick laminate greenlam ( supertuf or approved equivalent) or approved colour on flush door shutter with adhesive etc. (basic rate of Rs. 1200- per sheet) 150x10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality Golden lock or approved equivalent ) with a basic rate of Rs. 800/- for each

Door handle Stainless steel

Door Stopper

Hydraulic door closer (painted MS metal)

Providing and fixing 5mm float glass ( Modi float or equivalent) to aluminum window shutters including fixing aluminium beading, EPDM gasket etc. complete as per the drawings and direction of the engineer-in-charge.

Providing and fixing 20 mm thick mirror polished Granite stone on countertops and facia, laid over 12 mm thick cement mortar of 1:2 (1 cement 2 coarse sand) and finished on top as per Item [52] above, including cutting holes etc. for sinks and making curved semicircular nosing on all exposed edges in front of counter, over sinks etc. Granite stone of any colour thickness 19 mm (Basic rate 175 sqft)

Supplying and fixing rolling shutters of approved make, made of required size M.Slaths, interlocked together through their entire length and jointed together at the.end by end locks, mounted on specially designed pipe shaft with brackets, sideguides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wiresprings manufactured from high tensile steel wire of adequate strength conformingto IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes andhaving NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powdercoated of thickness 60 microns (minimum), including factory painted after bendingand perforation, and backed with a black Glass fiber acoustical fleece

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.

Sanitary work

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 100 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I, rain water pipes embedded in and including cement concrete blocks 10x10x 10cm of 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc.100 mm diameter.

Providing and fixing urinal with sensor type plate SNR-CHR-51097 AND URINAL-URSWHT-13255

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushingcistern, including flush pipe, with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required:

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. internal work - Exposed on wall 15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work) 15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work) 20 mm dia. nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete. 25 to 40 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore, 86 mm long, weighing not less than 88 gms

Providing and fixing wash basinJDS WHT 25907 with C.I. brackets, 15 mm dia CP Brass single hole basin mixer with sensorSNR-CHR-51033 of approved quality and make, including painting of fittings and brackets, cutting and making good the walls

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse Inside size 60x45x50 cm. inside including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg): With F.P.S. bricks with class designation 75

Electrical work

WGPVCPT Point wiring in PVC conduit, with piano type switch: wiring for light point / fan point /Ex Fan Point/Call Bell Point recessed PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc. as required. Group C

LPACCPT S / F light plug point piano type accessories: Supplying and fixing metal box of 150 mm x 75 mm x 60 mm deep(nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 anos socket outlet and 5/6 amps piano type switch, connection, painting etc. as required.( For light plugs to be used in non residential buildings).

WGSTLPTTC Twin control Point wiring in PVC conduit, with piano type switch: wiring for twin control light point recessed PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc. as required.

PPACCPT S/F power plug point piano type accessories: Supplying and fixing matel box of 180 mm x 100 mm x 60 mm deep on surface or in recess with 15 Amp piano type switch and socket. Complete with all work

MCBDPSOC20 S/F 20A SPN MCB industrial socket outlet: Supplying and fixing 20amps, 240 volts, SPN industrial type, socket outlet, with 2 pole

WGPVCSB Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring along with earth wire with the following size of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 2 x 1.5 sq. mm + 1 x 1.5 sq mm earth wire.

WGPVCSB Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring along with earth wire with the following size of PVC insulated copper conductor, single core cable in surfac

WGPVCSB Circuit/sub-man wiring in PVC conduit: Wiring for circuit/ submain wiring along with earth wire with the following size of PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required. 4 x 2.5 sq. mm + 2 x 2.5 sq mm earth wire.

CREB S / F Ceiling rose : Supplying and fixing 3 pin 5amp ceiling rose including connection etc. as required

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

EARGIPL GI earth plate electrode:Earthing with GI earth plate 600x600x6 mm thick i/c accessories and providing masonary encloser with cover plate having locking arrengement and watering pipe etc complete work

EARGIWRPIP P/F of 6 SWG GI earth wire in pipe Providing and laying earth connection from earth electrode with 6 SWG GI wire in 15 mm dia GI pipe complete work

TPMCBDB S/F TP MCB DB:4 way (4 +12), Double door, hotizontal type

MCBC S/F C series SP MCB S/F 5 amo 32 amp rating,240V C series MCB on existing DB complete with connections.

MCBTPIS S/F TP MCB isolator : S/F 100 amp rating ,415V isolator on existing DB complete with connections.

S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16S.W.G. M.S. sheet incorporating 10mm dia. M.S. bar round and duly painted with red oxide along with all work

Supply and Eraction testing of Exhaust fan complete with all work

Supply Eraction testing of ceiling fan etc excluding supply of down rod complete in all respect

Supply and fixing 2x2 ceiling light bajaj/wipro

coupper pipeing for hvac work spilit type (1/2+1/4) with insulation

Supply and laying 2.5 sqmm 4 core cable

Supply and laying pvc 25mm dia drain pipe

Supply and fixing 1.5 ton AC UNIT INDOOR AND OUT DOOR UNIT

Construction of Septic Tank

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Honey-comb brick work 10 / 11.4 cm thick with common burnt clay bricks of class designation 7.5 in super structure above plinth level upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

SAPTIRISHI ENVIRO SOLUTIONS PVT LTD