Construction of New Pumping stations and Upgradation existing Drainage Pumping stations at Kailashahar Dharmanagar Udaipur under the Scheme for Special Assistance to States for Capital Investment 2024 25

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. -All kinds of soil

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level: 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of RMC from transit mixer to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level Reinforced cement concrete grade M-25 using 418 kg of cement per cum

Extra for providing richer mixes at all floor levels. Providing M-30 grade of concrete instead of M-25 grade of concrete B.M.C/R.M.C

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering shuttering including struttings, propping etc. and removal of form work for: Foundations, footings, bases for columns etc. for mass concrete with timber plank

Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply

Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply

Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply

First class brick work in foundation and plinth including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required:- G.I.pipes.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:-

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:

Providing and fixing Precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc. all complete as per direction of Engineer-in-charge.

12 mm cement plaster of mix Cement mortar 1:4 (1 cement : 4 fine sand)

Neat cement punning

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge :

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : Coupler 110 mm

Single pushfit Coupler 110 mm

Single equal tee without door 110X110X110 mm

Single equal tee without door 110X110X110 mm

Bend 87.50 110 mm

Plain shoe 110 mm

Providing and fixing un-plasticised - PVC pipe clips of approved design to un-plasticised - PVC rain water pipes by means of 50 mm × 50 mm × 50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing with cement mortar 1:4 (1cement : 4 fine sand), making good the wall etc, complete 110 mm

Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8 mm and weighing not less than 100 g, complete 110 mm

Supply of Submersible Non Clog pump, Discharge: 500 lps, Head: 10M

Installation of Submersible Non Clog pump, Discharge: 500 lps, Head: 10M

Supply of Submersible Non Clog pump, Discharge: 600 lps, Head: 12M

Installation of Submersible Non Clog pump, Discharge: 600 lps, Head: 12M

Supply of Submersible Non Clog pump Discharge: 500 lps, Head: 15M

Installation of Submersible Non Clog pump Discharge: 500 lps, Head: 15M

Providing and fixing CIDF Butterfly valve with bolts, nuts,rubber insertions etc. complete as per CPWD specification and direction of the Engineer - in - charge. ( The tail pieces, tappers etc if required will be paid separately ) 400mm dia

Supply & Installation of Dismantling Joint 400mm dia

Providing and fixing C.I. non-return valve of approved quality as per CPWD specification and direction of the Engineer - in - charge. 400mm dia

Providing and fixing C.I. double action air valve of approved quality with bolts, nuts, rubber insertions etc. complete as per CPWD specification and direction of the Engineer - in - charge. ( The tail pieces, tapers etc if required will be paid separately ). 50mm

Providing and laying Doubled flanged ( Screwed / Welded ) Centrifugally cast ( Spun ) Ductile Iron Pipes of Class K 9 conforming to IS : 8329 as per CPWD specification and direction of the Engineer - in - charge. 400 mm dia Ductile Iron Doubled flanged

Providing and laying S & S Centrifugally Cast ( Spun ) Ductile Iron Class K-7 Pipes conforming to IS : 8329 as per CPWD specification and direction of the Engineer - in - charge. 1000 mm dia Ductile Iron Class K-7 pipes.

Providing and laying S & S Centrifugally Cast ( Spun ) Ductile Iron Class K-7 Pipes conforming to IS : 8329 as per CPWD specification and direction of the Engineer - in - charge. 900 mm dia Ductile Iron Class K-7 pipes.

Providing and fixing DI specials as per CPWD specification and direction of the Engineer - in - charge. A) D.I. all socketted Bend 90 degree 400mm dia

Supply & Installation of Manual Coarse Screen (2000mm X 2000mm)

Supply & Installation HOT Crane (3 Ton)

Supply and Installation of Chain Pulley Block (1 Ton)

DTR 1000 KVA 11/0.433 KV Aluminium Wound- BIS Level-2

Main LT Panel Incomer: 1000A FP ACB, Outgoing: 6 nos. 320A TPN MCCB with MPR, 1 no. 25A SP MCB & 1 Nos. 10A SP MCB

Incomer: 1250A FP ACB, Outgoing: 6 nos. 400A TPN MCCB with MPR, 1 no. 25A SP MCB & 1 Nos. 10A SP MCB

Incomer: 2000A FP ACB, Outgoing: 7 nos. 400A TPN MCCB with MPR, 1 no. 25A SP MCB & 1 Nos. 10A SP MCB

Power and Control Junction Box

Supply & Laying of aluminium conductor armoured cable with necessary connection etc as required 3.5 core 400 Sq mm

3.5 core 120 Sq mm

3.5 core 50 Sq mm

3.5 core 25 Sq mm

4 core 16 Sq mm

4 core 10 Sq mm

Earthing with Copper earth plate 600 mm x 600 mm x 3 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12"x 12" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:-

Earthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12"x 12" having locking arrangement including CC work, holes on earth pipe etc. as required.

Channel 100x50x6mm (Galvanised)

Channel 75x40x6mm (Galvanised)

Angel 65x65x6mm (Galvanised)

Angel 50x50x6mm (Galvanised)

Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required.

Supplying and installation of industrial plug & socket complete with metal enclosure including necessary connection etc. as required of the following ratings (without MCB):- 20 amps 230/240 volts single phase suitable for SP/SPN/DP MCB:-

Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:- 6 to 32 amps DP MCB:-

Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):- Surface mounted integrated 20 watt LED batten with polycarbonate diffuser:-

Supplying & installation of 450 mm sweep 1400 rpm metalic body exhaust fan including connection etc as required (ISI marked) :-

Supplying & installation of shutter for 380/450 mm sweep metalic body exhaust fan in the existing hole as required:-

Please Enable Macros to View BoQ information