8566/E8

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed.

Demolition of precast cement concrete block walling built in cement mortar all as specifed and as directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.5 metre in depth for foundation and getting out in soft loose soil all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5mtr in depth for foundation. (Laying of under ground cables) in hard/dense soil and getting out all as directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.5 metre in depth for foundation and getting out in hard rock using chisel/ pneumatic hammer all as specified and directed.

Returning, filling in including spreading leveling, watering and wall ramming in layers not exceeding 25cm in soil all as specified and directed.

Removal of surplus soil to a distance not exc 100 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point all as specified and directed.

M&L PCC 1:4:8 type D2 (using 40mm graded crushed stone aggreagte) in foundation filling and mass concrete all as specified and directed.

M&L PCC 1:3:6 type C2 (using 40mm graded crushed stone aggreagte) in surface channel and drain all as specified and directed

M&L PCC (1:2:4) type B-1, using 20 mm graded crushed stone aggregate as in benching etc or similar items all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, finished even and smooth using extra cement including forms, moulds, mitred/stopped ends all as specified and directed.

M&L pre-cast PCC 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) in cover slabs to man holes set in cement mortar 1:4 all as specified and directed

M&L PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in coping including necessary form work, including weathering, slightly rounded or chamfered angles and throating all as specified and directed

Use and waste form work to sides of concrete foundations, plinth beams for rough finished surfaces of concrete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, all as specified and directed.

Use and waste form work to sides of column for fair finished surfaces of concrete square retangular all as specified and directed.

Use and waste formwork to chajjas including edges for fair finished surfaces of concrete all as specified and directed.

M&L RCC M-25 grade design mix as in foundation, plinth beams and mass concrete all as specified and directed.

M&L RCC M-25 grade design mix as in Columns or fair finished surfaces of concrete all as specified and directed.

M&L RCC M-25 grade design mix as in beams, cantilevers, lintels over 1.5m span or fair finished surfaces of concrete all as specified and directed.

M&L RCC M-25 grade design mix as in slabs supported on walls, beams and columns in floors, roofs and shelves and the like work or fair finished surfaces of concrete all as specified and directed.

M&L for reinforced cement concrete M-25 design mix as in chajja or fair finished surfaces of concrete all as specified and directed.

M&L TMT bars 10 mm dia and over cut to length, bent to shape, required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clip all as specified and directed.

M&L TMT bars 8 mm dia cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hoooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to all as specified and directed

All as item No 24 above but 8mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified and directed.

S&F Fe 410-W Gde-E-250 (quality A) plates (plain or chequered) channels. square cut or notched (ordinary and counter sunk) forming holes, without any attachment all as specified and directed.

S&F roof trusses (framed), trussed, purlins Fe 410-W (Gde E-250) quality B and fastenings beam, tee, angle channels or flat sections including distance pieces cleat etc all as specified and directed.

S&F Fe 410-W Gde-E-250 (quality A) rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for fixed with angle cleats or other connecting plates all as specified and directed.

S&F pre-painted galvanlume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge of roof covering, fixed vwith self tapping screws all as specifierd and directed.

S&F pre-painted galvanlume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering,fixed with self tapping screws all as specified and directed.

S&F mild steel screw bolts (machine made ) with hexagonal or square head at one end and screwed the other ends, each screwed end fitted with washers and one hexagonal or square nut exc 16 to 20 mm dia and exc 22.5 cm long but nexc 30 cm long all as specified and directed.

S&F for pressed steel frames 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay with glazing bars, dovetailed or welded all as specified and directed

S&F Mild steel framed work of E-165 (Fe-290) as in grills/guard bars shouldered with steel windows/ventilators frames all as specified and directed.

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

S&F MS barrel tower bolts stove enamelled black with bright bolts 200mm long all as specified and directed.

S&F mild steel pressed handles, oval type, stove enamelled black 125mm long all as specified and directed.

S&F butt hinges medium weight cold rolled mild steel 100 mm long all as specified and directed.

S&F mild steel sliding door bolts, 300 mm long plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified and directed.

M&L pre cast cement concrete solid block masonry 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) exc 10 cm in width set in CM 1:6 all as specified and directed.

M&L precast PCC 1:3:6,type C-1,using 20mm graded crushed stone aggregate cement concrete block masonary with solid blocks exc 10cm in width set in cement mortar 1:4 all as specified and directed.

M&L rendering 15mm thick on other than fair faces of concrete surfaces in CM 1:6, finished surfaces even and smooth without using extra cement all as specified and directed

M&L rendering 15mm thick on fair faces of concrete surfaces in CM 1:4 finished surfaces even and smooth without using extra cement all as specified and directed.

M&L rendering 10 mm thick on fair faces of ceiling/soffits & sides of concrete surfaces in CM 1:3, finished even and smooth without using extra cement all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white washing all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white washing all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick laid over 15mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as specified and directed

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

M&L for hardcore of broken stone of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L 75mm thick PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregate ) as in plinth protection, finishing the concrete surface even and smooth without using extra cement all as specified and directed.

S&F 0.56 mm nominal dia of wire galvanised mild steel wire cloth and average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staple all as specified and directed.

S&F 3mm thick sheet glass ordinary qualiy and glazing with oil putty in square not exc 0.5 sqm in each pane all as specified and directed

M&L for point wiring with 1.5 sq mm PVC insulated unsheathed single core multi-stranded copper conductor FRLS cable 1100 Volts grade drawn through and including 20mm dia (medium grade) PVC conduit along with 1.5 sq mm continuous PVC insulated multi stranded copper conductor cable for earth continuity wire and, connected to earth dolly and to be terminated in and including pressed steel sunken boxes readily available (having wall thickness not less than 1.22 mm for boxes up to size of 200 mmx300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed in permanent building and fixed on surface in temporary building, covered with 3.0 mm thick bakelite sheet for mounting switches, sockets, fan regulators including testing on completion all as specified and as directed by the Engineer-in-charge for one light point controlled by one one way switch

All as per item No 57 above but for one three/five pin switch-socket outlet, 5 Amps on the same board.

All as per item No 57 here-in-before but for one three/five pin switch-socket outlet, 5 Amps on independent board.

All as per item No 57 here-in-before but for one 16 Amp 3 pin/5 pin switch socket outlet, on independent board, with 4 sq mm single core stranded copper conductor along with 2.5 sq mm continuous PVC insulated unsheathed stranded copper conductor cable as earth continuity wire, all as specified and as directed.

S&F switch piano flush type, single pole one way 6 Amps 230 volts all as specified and as directed.

S&F lamp holder insulated body with back plate and AC 230 V all as specified and as directed.

S&F ceiling rose, surface bakelite 65 mmx50 mm size with three terminals all as specified and as directed

S&F Socket outlet 2 in 1, 3/5 pin, 5/6 Amps flush type all as specified and directed.

S&F switch socket combination 3 in 1, 6 pin, 16 Amp flush type all as specified and directed.

S&F LED tube light fitting bright line 18 watt bright light out put of 1800 Lumens affordable batten with100Lm/W efficiency slim elegant design 35000 hrs long life LED all as specified and directed. Make:- Baja/Hevells/Philips india limited

S&F sheet metal enclosure for double door MCB DBs, phosphatised, powder coated, single pole & neutral (SPN), suitable for 8 way, 240 volts, fixed on wall with dia rail neutral and earth bar in proper position all as specified and directed.

S&F MCB single pole with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding suitable for single phase circuit of 6 to 32A all as specified and directed.

All as per item No 68 above but MCB DP 32/40 Amps.

S&F new security light fitting complete with 25 watt LED type LSTO-25-CDL pressure die cast aluminium housing and heat resistant toughned glass with frame IP-66 protection and better optics for uniform distribution, fixed bracket made out of GI pipe (light grade) of suitable size and MS clamp and nut bolts washers etc complete and connected with twin core cable 1.5 sqmm from ceiling rose to fitting connector all as specified and directed.

S&F 12 watt LED bulb. cool day light, 230/240V AC supply all as specified and as directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 600 mmx 600 mmx 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized steel earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work in any type of strata, PCC (1:3:6) type C-I with 50 mm thick pre-cast RCC (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm c/c both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or earthing test point as directed, and necessary testing on completion all as specified and as directed.

M&L sand cushioning for protection of PVC cable with approved sand of uniform thickness, laid dry, by filling in trenches and punning to proper required cover all as specified and as directed. Note:- For the purpose of payment only punned thickness will be measured.

Supply and laying old size sub-class ’B’ bricks laid flat length equal to width of bricks, perpendicular to UG cable over dry sand cushioning, for cable protection all as specified and as directed.

M&L for 25mm dia steel tubes (light grade) galvanised with all fittings, laid in trenches/wall/pole for protection of underground cable when crossing the road/fixing

Supply and fix 1100 volt grade heavy duty cable PVC insulated multi stranded aluminium conductor size 10 sqmm 2 core flat served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4 mm dia suspension wire all as specified and directed.

JHURI PRASAD AND SONS

M/S Swarn Constructions