PROVN OF FOUR LOW COST OPEN IRON SHED AT 46 AD REGT AND ADDITION /ALTRATION TO BLDG NO-429/321 AT MIL STN BHUJ

Amount

Surface Excavation in Hard/dense soil n.exc.(not exceeding) 30 cm deep and averaging 15 cm deep and getting out complete as all spfd and directed by Engr-in-charge

Earthwork in excavation in trenches as in foundation n exc. 1.5 M. wide and n exc. 1.5 M in depth as in Hard/Dense soil and getting out complete as all spfd and directed by EIC

Returning, filling in soft/loose soil including spreading, levelling, watering and well ramming in layers not exc 25 cm thick as all spfd complete and directed by EIC.

Removing excavated material (Soil) n.exc. 50 m and deposting where directed at a level n.exc. 1.5 m above the starting point complete as all spfd and directed by Engr-in-charge

M/L Cement concrete PCC 1:3:6 type C- 2 as (40 mm graded aggregate) in foundation filling and in mass concrete

M&L Reinforced cement concrete B1 1:2:4 (20 mm graded aggregates) foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed.

M&L reinforced cement concrete B1 1:2:4 (20 mm graded aggregates) Columns, pillars, piers,posts and struts etc complete all as spd and directed.

M&L reinforced cement concreteM-20 (20 mm graded aggregates) as in beams, cantileavers, bressummers, lintels over 1.5 clear span etc complete all as spd and directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to lengths, bent to shape as required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed) not less than 0.9 mm dia or securing with clips. Complete as all spfd and directed by EIC

Ditto as above item but 5 mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete as all spfd and directed by EIC

Use and waste of formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffit(if any) of foundation and plinth beams and similar work vertical or to batter to rough finished flat surfaces of concrete complete as all spfd and directed.

Use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions of rough finished square,rectangular or polygonal surfaces of concrete complete as all spfd and directed.

Use and waste of Formwork to sides of beam of rough finished square,rectangular or polygonal surfaces of concrete complete as all spfd and directed.

S&F for mild Steel Screw bolts(machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 22.5 cm but n.excc. 30 cm long and diameter of neck 16 to 20 mm complete as all spfd and directed by EIC.

S&F mild steel roof trusses (framed) trusses, purlins,angle iron, square pipe and fastening (etc.,angle, channel) or flat section including distance pieces, MS plates/ gusset plates, cleats, hold fast,purpose for water tanks staging etc. conforming to Gde of steel Fe 410-0 (Grade-Fe 250) quality A with and including complete all as specified and directed.

M & L for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering / cladding to wall, fixed with L or J hooks all as specified and directed.

M & L for pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering / cladding to wall, fixed with L or J hooks all as specified and directed.

M&L for preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete as all spfd and directed by EIC

M&L Hardcore of broken stone or boulders of gauge nexc.63mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete as all spfd directed by EIC

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate 150 mm thick as in sub base

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate 55 mm thick as in finishing surface even and smooth without using extra cement complete all as specifed and directed.

M&L forming construction joints 30mm deep x 10mm wide filled with ceiling compd Grd 'B'

M&L for precast cement concrete block masonry with solid blocks of PCC (13:6) (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on fair surface brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement incl three coats of white wash complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L non skid ceramic tiles(Coloured) 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Demolition of precast concrete block walling and similar items i.e.. ashlar facing dressed stone work, precast concrete articles etc., of any description and in any position, built in cement mortar, including all quoins, arches and pillars etc. complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers i.e.. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) aas per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces/stone masonry and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls & applying 2 coat of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls & applying three coats of white wash on wall surfaces complete all as specified and directed.

Dismantling water tanks of any description and in any position , of capacity exceeding 500 litres but not exceeding 1000 litres complete all as specified and directed.

S & F Rotational moulded poly-ethylene multilayer water storage tanks (cylindrical vertical with closed top) 1000 litres capacity, white in colour hoisted and fixed in position with and including all fittings and fixtures in repairs complete all as specified and directed.

S&F Ball brass valves , high pressure , with polythene float and fly nut complete & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed.

Taking down chowkat or frames exc 1.5 sqm & n exc 4 sqm with shutters without taking off shutters from the frame and removing to store

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & prelam both side colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of prelam colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required & directed by the Engr-in-Charge.

S&F solid PVC door frame of size 50mmX47mm made out of 5mm one side prelam colour PVC sheet reinforced with MS square tube all as per specifications and as per drawing shown on sl page No 150 of SSR part II (for item-884)

S&F aluminium handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed.

S&F butt hinges 100mm long medium weight, cold rolled mild steel.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F in repair sinks with drainage board made out of stainless steel 1 mm thick kitchen or laboratory with ;plugs, washers, and waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, and connecting union to pipe overall size 915 mm x 460 mm with bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed .

S&F (concealed / open) 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 15mm bore..

S&F (concealed / open) 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 20mm bore.

S&F (concealed / open) 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 25mm bore.

Dismantling plain or corrugated A/C or steel sheeting, any gauge of any description and in any position as in roof coverings

S &F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering / cladding to wall, fixed with L or J hooks all as specified and directed.

M&L Excavating in post holes (or similar holes)soft/loose soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

M&L for cement concrete 1:4:8 type D2 (using 40mm graded aggregate) in foundation filling & mass concrete

Dismantling structural steel work of any description and in any position including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.Fe 410 -W (Gde- E- 250) quality-A

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including GI bracket made to shape and size complete all as specified and directed by Accepting officer.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with starnded aluminium conductor of size 4 core 16 sqmm complete all as specified and directed by Accepting officer.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc for laying of cables, erection of poles, struts/ stays etc not exceeding 10 sqm on plan and getting out in soft loose soil.

Returning, filling in, including spreading leveling watering and well ramming in layers not exceeding 25 cm in any type of soil.

M & L for sand filling in trenches for cushioning of LT cables punning after filling complete as specified and as directed. Note: Punned thickness shall only be measured and paid

Supply and lay un-reinforced precast concrete cable cover , class , LV , Type I flat size 250 x 150 x 40 mm laid dry in treches over under ground cables.

M&L for point wiring with using 1.5 Sqmm (nominal area) multi standard copper conductor, single core, FRLS PVC insulated & unsheathed cable, 1100 volts grade with and including PVC conduit of adequate size fixed on surface with PVC rawl plugs with sunken type pressed steel terminal box and junction boxes 1.6mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings and wiring to be terminated in pressed steel sunken boxes with and including all accessories and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, FRLS PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed for following:- (a) one light point controlled by one,one way switch NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes to required depth & making good the disturbed surface in CM 1:4 including finishing the surface to match with the existing surface. (ii) Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iii) The quoted rates shall be deemed to be inclusive for provision of covering sunken boards/terminal boxes / junction boxes of any shape and size with 3mm thick laminated sheet fixed with suitable brass screws and cup washers

All1ser item No.61 8 here-in-before but with 4 sq mm size FRLS pvc insulated and unsheathed 1100 volts grade single core stranded (multistrand) copper conductor cable for 3 pin socket outlet 15 amp on independent board.

S&F ceiling rose surface bakelite 63.5 x 20 mm, three terminals, complete all as specified and directed.

S&F switch flush type, 5/6 Amps, single pole, one way, 230 volts AC circuit complete all as specified and directed.

S&F switch socket outlet combination, multipurpose, three pin, 15 Amps & three pin 5 Amps controlled by one switch , flush type, 230 volts AC circuit complete all as specified and directed.

S & F in replacement elegantly industrial general purpose box type luminaire, 1x20 Watt, designed box type LED luminaries, CRCA sheet steel housing with white reflector cover fitted to the body with decorative end covers complete with electronic ballast, spring loaded rotor type lamp holders, connected block with and including 01 No LED lamp 20 Watt and all accessories, pre-wired and connecting the same to ceiling rose with & including twin core PVC insulated and sheathed copper conductor 23/0.0076 cable including all accessories and fixing arrangement for fixing the light fitting to walls / roof surface over and including 2 Nos PVC square box complete all as specified and directed.

S & F sheet metal enclosure powder painted for vertical type MCB DB TPN 04 way double door with IP-42 protection with Din rail and busbar complete all as specified and directed by accepting officer

Supply and fixing MCB TPN, 63 Amps in `C’ series having current rating 10 KA complete all as specified and directed. Make :-Havells or equivalent others make as specified.

S&F MCB single pole, 6 to 32 Amps in `C’ series having current rating 10 KA complete all as specified and directed :- Make :-Havells or equivalent others make as specified.

M&L for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level (with top edge of earth plate not less than 1.5 metre below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe medium grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia medium grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick precast RCC cover in 1 : 2 : 4 type B-1 with 3 Nos 8 mm dia TMT bars both ways with 12mm dia round bar handle complete all as specified & directed. NOTE: Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item and additional earth GI earth wire/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item of Schedule `A’

Ram J. Laljani

M/S S. SINGH TRADERS

M/s Bombay Novelty Stores