Loading…
Loading…
| # | Company | Amount |
|---|---|---|
| 1 | ₹37.6 Cr 515 MANGLAM PARADISE MALL MANGLAM PLACE SECTOR 03 ROHINI DELHI 110085 | ₹37.6 Cr |
Tender Value
₹49.9 Cr
EMD Value
₹49.9 L
Closing Date
29 May 2025, 11:00 amClosed
Construction of Multi-storied Building to accommodate Six Courts including XI Additional District court at Gudivada, Krishna District, A.P.
NBCC/CPG/Gudivada/AP/2025/485
NBCC/CPG/Gudivada/AP/2025/485
Open Tender-Domestic
Civil Works General
Krishna, Andhra Pradesh
₹59,000
₹49.9 L
6 May 2025
6 May 2025
29 May 2025
29 May 2025
16 Jun 2025
TOTAL AMOUNT Rs. 49,93,72,451.56
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the
cost of chemical emulsion) :
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including
15.1 2.35.3 drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the
existing floor:
15.1.1 2.35.3.1 With Chlorpyriphos E.C. 20% with 1% concentration Sqm 2,656.00 310.05 8,23,492.80
TOTAL EARTH WORK CARRIED TO SUMMARY 69,59,599.37 -
C SH-4.0 CONCRETE WORKS
Providing and laying in position cement concrete of specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm
nominal size derived from natural sources).
1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm
nominal size derived from natural sources).
Sign of Contractor Page 2 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm
nominal size derived from natural sources)
1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm
nominal size derived from natural sources)
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand
21.0 4.11 (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural Sqm 91.52 402.50 36,836.80
Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement Per 1
as per manufacturer’s specification. Cement Bag
Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7
23.0 4.13 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of Sqm 91.52 146.15 13,375.65
cloth lightly soaked in kerosene oil.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived
from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over
75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine
sand, including necessary excavation leveling & dressing & finishing the top smooth.
TOTAL CONCRETE WORKS CARRIED TO SUMMARY 65,19,723.35 -
D SH-5.0 REINFORCED CEMENT CONCRETE WORK
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and
25 5.20 string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor
five level, excluding cost of centering, shuttering, finishing and reinforcement :
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm
nominal size derived from natural sources)
Providing and laying in position ready mixed or site batched design mix cement concrete for
reinforced cement concrete work; using coarse aggregate and fine aggregate derived from
natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in
recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and
workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all
26 5.33 leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the
engineer-in-charge; for the following grades of concrete.
Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable
separately. In case the cement content in design mix is more than 110% of the specified minimum
cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra
26.1 5.33.1 All works upto plinth level
26.1.1 5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum Cum 913.20 9,504.75 86,79,737.70
27 5.33.2 All works above plinth level upto floor V level
27.1 5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum Cum 3,770.29 9,860.40 3,71,76,518.21
28 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :
28.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 1,449.54 392.15 5,68,437.11
29 5.92 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc Sqm 1,151.00 842.50 9,69,717.50
30 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 3,444.32 736.40 25,36,394.23
31 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 4,610.83 961.30 44,32,387.03
32 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 611.20 764.95 4,67,537.44
33 5.9.15 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string Sqm 1,320.00 392.15 5,17,638.00
34 5.9.19 Weather shed, chajjas, corbels etc., including edges Sqm 137.95 951.10 1,31,204.25
35 5.9.20 Suspended floors, roofs, landings, balconies and access platform. Sqm 10,394.07 1,028.40 1,06,89,262.62
Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all
complete upto plinth & above plinth level.
36.1 5.22.6 Thermo-Mechanically Treated bars. Kg 7,95,737.88 107.85 8,58,20,330.52
37 5.3 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections Rmt 166.71 78.40 13,070.06
Providing and fixing of expansion joint system related with floor location as per drawings and direction of
Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning /
self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that
it provides floor to floor /floor to wall expansion control system for various vertical localtion in
load application areas that accommodates multi directional seismic movement without stress to it’s
components. System shall consist of metal profiles with an universal aluminum base member
designed to accommodate various project conditions and finish floor treatments. The cover plate shall
be designed of width and thickness required to satisfy projects movement and loading requirements
and secured to base members by utilizing manufacturer’s pre- engineered self- centering arrangement
that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular
sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of
movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier
Membrane in the Joint System to have watertight joint is mandatory requirement all as per the
manufactures design and as approved by Engineer -in-Charge. (Material shall conform to ASTM 6063).
Providing and fixing of expansion joint system related with wall joint (internal/external) location as
per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base
members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material
shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to
corner application, both new and existing construction in office Buildings & complexes with no slipping
down tendency amongst the components of the Joint System. The Joint System shall utilize light
weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking
the multicellular to facilitate movement. (Material shall conform to ASTM 6063).
Sign of Contractor Page 3 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing of expansion joint system of approved make and manufactures for various roof locations
as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum
base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The
system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control
system that is capable of accommodating multidirectional seismic movement without stress to its
components. System shall consist of metal profile that incorporates an universal aluminum base member
designed to accommodate various project conditions and roof treatments. The cover plate shall be designed
of width and thickness required to satisfy movement and loading requirements and secured to base
members by utilizing manufacturer's pre-engineered self-centering arrangement that freely rotates / moves in
all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including
vertical displacement.
The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV,
airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier
Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall conform to
Providing and fixing in position 12 mm thick bitumen impregnated fiber board conforming to IS: 1838,
including cost of primer, sealing compound Grade-A in expansion joints.
42 5.29 Providing and fixing sheet covering over expansion joints with iron screws as per design.
42.1 5.29.2 Aluminium, fluted strips 2.15 mm thick.
TOTAL REINFORCED CEMENT CONCRETE WORK CARRIED TO SUMMARY 16,20,20,138.04 -
E SH-6.0 BRICK WORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation
43.1 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 507.00 7,370.65 37,36,919.55
Extra for providing and placing in position 2 Nos 6 mm dia. M.S bars at every third course of half brick
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in all shapes and sizes in :
45.1 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 78.58 9,344.35 7,34,279.02
Brick work with non modular fly ash bricks conforming to IS: 12894, class designation 10 average
compressive strength I super structure above plinth level up to floor V level in :
46.1 6.34.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 3,444.00 8,962.35 3,08,66,333.40
Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S ( non modular) bricks
of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS : 12894, in supe
structure above plinth upto floor V level.
48.1 6.45.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 847.00 1,105.80 9,36,612.60
Honey-comb brick work 10 / 11.4 cm thick with common burnt clay bricks of class designation 7.5 in super
structure above plinth level upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand).
TOTAL BRICK WORK CARRIED TO SUMMARY 3,66,44,265.55 -
F SH-8.0 CLADDING WORK
Providing and fixing 18 mm thick Granite gang saw cut, mirror polished,premoulded and prepolished,
machine cut for kitchen platforms, vanitycounters, window sills, facias and similar locations of required
50 8.2 size,approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse
sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing,
curing,moulding and polishing to edges to give high gloss finish etc. completeat all levels.
51.1 8.2.2 Granite stone slab colour black, Cherry/Ruby red
Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine
cut edges) of uniform colour andsize upto 1mx1m, fixed to structural steel frame work and/ or with the help of
51 8.20 cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and
direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for
51.1 8.20.1 Red sand stone - 30mm thick gang saw cut stone Sqm 1,300.00 2,902.65 37,73,445.00
Providing and fixing structural steel frame (for dry caldding with 30 mm thick gang saw cut with machine cut
edges sand stone) on walls at all heights using MS square/rectangular tube in the required pattern as per
architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed ot the.
wall with the help of MS brackets/lugs of angle iron/flats etc. which shall be welded to the frame and
embedded in brick wall with cement concrete block 1:2:4 of size 300x230x300mm including cost of
52 8.21 necessary centering and shuttering drilling necessary holes. Approved cramps/pins etc shall be welded to Kg 3,500.00 269.95 9,44,825.00
the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as
approved by Engineer-in-charge and painted with two or more coats of epoxy paint (Shop drawings shall be
submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall
be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the
purpose of payment, stainless steel cramps shall be paid for seperately and nothing extra shall be paid).
Extra for fixing marble / granite stone, over and above corresponding basic item, in facia and drops of width
upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.
Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity
54 8.50 counter and similar location in marble / Granite / stone work, including necessary holes for pillar taps etc. Each 25.00 978.70 24,467.50
including moulding, rubbing and polishing of cut edges etc. complete.
Sign of Contractor Page 4 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by
the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size
55 8.31 as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement Sqm 6,042.00 1,267.95 76,60,953.90
mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade complete.
Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel
Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all
levels etc. including:
(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen
principle as required, proper drainage of water to make it watertight including checking of all the structural
and functional design
(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan
55 a 8.32 shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material Sqm 330.00 5,015.05 16,54,966.50
consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm
thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /
Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service)
coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone
sealant, backer rods etc.
(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and
serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved
make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per
Providing and fixing Glass fiber reinforced concrete screen/jali thickness 30-35 mm of approved pattern,
design, thickness and colour. Jali made with 53 grade white cement, quartz silica sand, alkali resistant glass
fiber, super plasticizer and polymer and UV resistant synthetic inorganic pigments etc. The screen/Jali shall
be fixed by dry fixing with stainless steel 304 grade "L" shaped cramps, dash fasteners etc. complete. Rate
shall included the structural Steel frame (Horizontal and Vertical member) support to hold the GRC Jalli at
required building height to withstand wind pressure. The Technical specification of screen/jali shall be as
under: Dry Density: > 1800 kg/cum Water Absorption: Less than 6% of dry weight by immersion over a
period of 24 hours. Compressive Strength: > 400 Kg./CM2 (M-40 Grade) Wet Transverse Strength: > 7N
/mm Abrasion Resistance: Less than 2.0 for E.H.D. Thermal Conductivity : 1.63 W/MK at 3% moisture
content 1.80 W/MK at 5% moisture content 1200mm x 600mm GRC Circular Band
TOTAL CLADDING WORK CARRIED TO SUMMARY 1,71,89,410.60 17,81,250.00
G SH-9.0 WOOD AND PVC WORK
Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary
56 9.12 float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window Sqm 500.00 176.40 88,200.00
shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core
57 9.21 of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering
with vertical grains or cross bands and face veneers on both faces of shutters:
57.1 9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm 411.54 2,392.65 9,84,671.18
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door
shutters (over all area of door shutter to be measured).
59 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). Sqm 411.54 106.70 43,911.32
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede
59.1 9.127 finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to
IS : 2046 Type S, including cost of adhesive of approved quality.
Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws
etc. complete :
Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever
handles of approved quality with necessary screws etc. complete.
Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade
AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :
Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10
as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :
Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as
per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less
65 9.101 than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws
65.1 9.101.2 Twin rubber stopper Each 146.00 72.35 10,563.10
Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing
with necessary screws etc. complete.
66.1 9.114.1 Triple strip vertical type Each 146.00 52.50 7,665.00
Sign of Contractor Page 5 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free
uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles
having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series
R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized
mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing
beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM
gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising
of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14,
plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if
required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including
drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and
adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved
size and quality, all complete as per approved drawing conforming to CPWD specification & direction
of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as
per design approved by Engineer-in- Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double
glass unit with / without high performance coatings as per design requirements and conforming to IS:
3548 & IS: 16231 shall be paid separately.
Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the
manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure
height more than 20m for all wind speeds
Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel
67.1 9.147.A4 for roller track, wool pile, nylon rollers with
Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen
every glazed panel along with multi-point locking system. (Height upto 1.8m).
68 9.147.C2 Fixed window / ventilator without mullion / transom.
Using R3 series with frame (55mm & above ) x (45mm & above) & mullion (55mm & above) x (65mm &
above). (Height upto 2.5 meter)
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid
door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-
60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non
toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC
solvent cement and screwed with full body threaded star headed SS screws having minimum frame density
of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive
strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A
category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in
position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of
Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type
flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade),
calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives
(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal
strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity
70 26.88 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,
water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of
approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt
hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per
direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round
bars etc. including priming coat with approved steel primer all complete.
71.1 9.48.1 Fixed to steel windows by welding Kg 27,050.00 219.10 59,26,655.00
TOTAL WOOD AND PVC WORK CARRIED TO SUMMARY 1,95,62,036.77 -
H SH-10.0 STEEL WORK
Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing
in position and applying a priming coat of approved steel primer all complete
Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with
flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel
pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat
of approved steel primer.
Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset
74 10.5 plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of
approved steel primer.
74.1 10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces Sqm 89.70 5,804.35 5,20,650.20
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together
through their entire length and jointed together at the end by end locks, mounted on specially designed pipe
shaft with brackets, side guides and arrangements for inside and outside locking with push and pull
operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs
manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top
cover of required thickness for rolling shutters.
75.1 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover. Sqm 17.00 3,653.20 62,104.40
76 10.7 Providing and fixing ball bearing for rolling shutters. Each 8.00 492.35 3,938.80
77 10.8 Extra for providing mechanical device chain and crank operation for operating rolling shutters.
77.1 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in the area. Sqm 17.00 1,181.80 20,090.60
Sign of Contractor Page 6 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting,
78 10.16 hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted
with special shaped washers etc. complete.
78.1 10.16.1 Hot finished welded type tubes. Kgs 2,000.00 194.40 3,88,800.00
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying
a priming coat of approved steel primer using structural steel etc. as required.
79.1 10.25.1 Hot finished welded type tubes. Kgs 1,000.00 123.60 1,23,600.00
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with
80 10.28 necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & Kgs 820.00 772.40 6,33,368.00
stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of
waist slab with suitable arrangement as per approval of Engineer-in-charge.
TOTAL STEEL WORK CARRIED TO SUMMARY 28,93,934.40 -
I SH-11.0 FLOORING WORK
Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement
81 11.20 slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm
thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
81.1 11.20.1 Light shade pigment using white cement. Sqm 964.32 1,402.00 13,51,976.64
Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform
thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper
grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of
coarse aggregate, watering and compacting to the required density.
Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade
made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in
required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints
with fine sand etc. all complete as per the direction of Engineer-in-charge.
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed
84 11.26 with pigment to match the shade of the slab including rubbing and polishing complete with base of cement
mortar 1 : 4 (1 cement : 4 coarse sand) :
Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified
by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any
85 11.37A size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of Sqm 594.00 1,112.70 6,60,943.80
cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including
pointing in white cement mixed with pigment of matching shade complete.
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)
with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer,
in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing
86 11.41A with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments
etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with
the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing
the tiles gently and easily
86.1 11.41A.1 Double Charged Vitrified tile Polished Finish of Size
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with
water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all
87 11.47.2 colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile Sqm 499.70 1,893.90 9,46,381.83
adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints
(Payment for grouting of joints to be made separately). Size of Tile 600x600 mm
TOTAL FLOORING WORK CARRIED TO SUMMARY 1,65,56,169.40 -
Sign of Contractor Page 7 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
J SH-12.0 ROOFING WORK
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,
suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm,
both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of
size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross
"T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at
600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size
24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to
form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved
texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings,
fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using Gl slotted cleats of size
27 x 37 × 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm Gl adjustable
rods with galvanized butterfly level clips of size 85 × 30 x 0.8 mm spaced at 1200 mm center to center along
main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all
complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.
88.1 26.27.1 With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.66) Sqm 2,051.00 2,333.60 47,86,213.60
Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special
sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side
inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27
mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia ×
50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of
required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5
mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm
centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips
89 12.45 made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5
mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition
with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including
fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 ×
25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the
board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers
covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per
manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers,
cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and
direction of the Engineer in Charge but excluding the cost of painting with : above Girth upto 610 mm
12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS
certification marks)
TOTAL ROOFING WORK CARRIED TO SUMMARY 1,12,77,784.00 -
K SH-13.0 FINISHING WORK
90 13.1 12 mm cement plaster of mix :
91 13.3 20 mm cement plaster of mix :
92 13.16 6 mm cement plaster of mix :
Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade
Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare
the surface even and smooth complete.
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic
96 13.83 Compound ) content less than 50 grams/ litre of approved brand and manufacture, including
applying additional coats wherever required to achieve even shade and colour.
Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less
97 13.48A than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior
paint of required shade with silicon additives.
New work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer
applied @ 0.90 litre/10 sqm.
98 13.45 Finishing walls with textured exterior paint of required shade
New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer
applied @ 2.20kg/10 sqm
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even
Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand
and manufacture
TOTAL FINISHING WORK CARRIED TO SUMMARY 4,00,68,909.71 -
L SH-22.0 WATER PROOFING
Preparing the inside surface of core and PVC by roughening using suitable file to get
better adhesion prior to packing works. Cleaning the surface by wire brushing
followed water jet to remove any laitance or loose flaky particles. Providing
necessary formwork for packing the bore using suitable arrangement (depending
upon site conditions). Applying a coat of styrene- butadiene based polymer coating
using SBR Polymer to enhance adhesion between the packing material and other Nos 350.00 450.00 1,57,500.00
surfaces. Packing the gap using non-shrink cement polymer based grout using Non-
shrink cementitious grout upto the surface of the bore whilst the SBR Polymer is in
tacky state. The above analysis is based on assumption for 150mm diameter core
with 110mm diameter PVC for 5” thick slab only. Typical Properties Compressive
strength at 28day as per BS 1881 45N/mm2, completely as per the manufacturer’s
Sign of Contractor Page 8 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
Coving treatment including Providing gola 75x75 mm in cement concrete 1:2:4 (1
100.1 NS cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge) admixed with Rmt 540.00 265.00 1,43,100.00
water proofing liquid
Waterproofing of roof slab
Primer: Supply & application of diluting Single Component PU and Solvent at 1:1
proportion on the prepared surface.
Waterproofing membrane
Supply and application of single-component, Pitch free seamless roller/spray
applied Single Component PU applied at average minimum DFT of 1.5 mm using a
Graco King type pump with 60:1 ratio at pressure 5.5 bar (80 psi), hose diameter
13mm with a 10mm wip end. Tip size: 0.58mm - 0.84 (23-33 thou). It shall possess
100.2 NS the following properties: Solids by Volume : 85%, Tensile Strength ASTM D412 : >1.9 Sqm 3,651.00 1,950.00 71,19,450.00
MPa, Tear resistance ASTM D624C : 15(N/mm), Elongation ASTM D-412 :
>400%,Adhesion in-peel test ASTM C836 (N) : > 50N
Screed Concrete Protection on WPT
Providing a non-woven Geotextile fabric of 200GSM over the cured waterproofing
membrane before going for a protective layer.
Horizontal Protection
Providing and laying min 50/75mm (as per the design thickness to provide proper
slope at 1:100 or 150) thick polymer modified screed concrete of M20 grade and
admixed with Integral waterproofing compound confirming to IS 2645 of Water
Waterproofing of TOILET
Providing and applying 2mm acrylic polymer modified elastomeric cementitious
101 NS waterproofing membrane The applied waterproofing system shall have tensile Sqm 1,210.00 850.00 10,28,500.00
strength >1N/mm2, Bond strength >1MPa. With minimum 12 mm thick 1:4 cement
plaster to laid with water proofing liquid
TOTAL WATER PROOFING CARRIED TO SUMMARY - 84,48,550.00
M SH-25 ALLUMINIUM & GLASS WORKS
Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural
drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,
including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and
shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves,
screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this
account). The weight of aluminium extruded section shall be taken for purpose of payment.
Designing, fabricating, testing, protection, installin and fixing in position semi (grid) unitized system of
103 25.2 structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and Sqm 1,443.40 3,501.00 50,53,343.40
Supplying of Ocean blue 5mm thick tougned glass having U value 5.71 W/M2 degree K, transmission 28%,
light refelection internal 29% and external 20%and shading coeffiecent 0.45 as per direction of EIC
Extra for openalbe side/top hung vision glass panels including providing and supplying at site all accessories
and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless
105 25.4 steel friction hinges, min 4-point cremone locking sets with ss plates, handles etc. including necessary ss Sqm 45.00 3,671.50 1,65,217.50
screws, nuts etc all complete as per the Architectural Drawing as per the approved shop drawings as
specified and as directed by the engineer-in-charge
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up
standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733
and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at
junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections
shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be
paid for separately) :
106.1 21.1.1 For fixed portion
Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
106.1.2 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kg 400.00 530.90 2,12,360.00
Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle
board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and
partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and
directions of engineer-in-charge.
107.1 21.2.2 Pre-laminated particle board with decorative lamination on both sides. Sqm 200.00 1,115.40 2,23,080.00
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM
108 21.3 rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-
charge . (Cost of aluminium snap beading shall be paid in basic item):
108.1 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sqm 200.00 1,505.25 3,01,050.00
Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to
IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight
109 21.4 upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the
same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet
outer box with slide plate etc. complete as per the direction of Engineer-in-charge.
109.1 21.4.1 With stainless steel cover plate minimum 1.25 mm thickness. Each 25.00 2,823.85 70,596.25
Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon
110 21.8 sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-
charge complete.
110.1 21.8.1 With stainless steel cover plate minimum 1.25 mm thickness. Rmt 96.75 2,823.85 2,73,207.49
Sign of Contractor Page 9 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR NON DSR
S.NO Description Unit Total Qty Rate in Rs
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles
of height 259/ 309/ 409mm and lengthof 1190 mm of approved texture,design and pattern having Flexural
Strength/ Modulus of Rupture of ? 14 N/m² and maximum
water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level
fixed to a supporting aluminium framework (Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L'
(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm
respectively, spaced at maximum spacing of 1200mm c/c matching to the tile vertical grid, and horizontal
111.0 NS aluminium 'C'-clamps of size 56x34x2
mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of
the vertical sections at spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two numbers
of self-drilling / self-tapping SS screws of size
5.5x25 mm with EPDM washers.The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-
dip-galvanized) steel Lbrackets (galvanizing thickness of minimum 80 microns) of size 110x80x6 mm at
intermediate vertical aluminium profiles and of size 220x110x12 mmat outer corners and stainless steel
grade 304,M10 full threaded anchor fasteners with nylon sleeve 100mm long (for brick work) and M8
expansion anchor fasteners 75mm long for concrete surface, spacing of brackets to be based on a
111.1 NS With 24mm thickness (+/- 10%) terracotta tiles of other than grey colors Sqm 350.00 5,842.50 20,44,875.00
TOTAL ALLUMINIUM & GLASS WORKS CARRIED TO SUMMARY 66,05,014.64 53,86,346.00
Sign of Contractor Page 10 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING
S.NO Description Unit Qty Amount in Amount in
EXTERNAL DEVELOPMENT
A 1 BOUNDARY WALL
Earth work in Excavation by mechanical means (Hydraulic
excavator)/manualmeans over areas (exceeding 30 cm in depth, 1.5 m in width as
well as 10sqm on plan) including getting out and disposal of excavated earth lead
upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of
2 2.25 foundations etc. in layers not exceeding 20cm in depth, consolidating each Cum 142.00 196.00 27,832.00
deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
Providing and laying in position cement concrete of specified grade excluding the
3 4.1 cost of
centering and shuttering - All work up to plinth level :
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded
stone aggregate 40 mm nominal size derived from natural sources)
1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10
graded stone aggregate 40 mm nominal size derived from natural sources)
Reinforcement for R.C.C. work including straightening, cutting, bending, placing in
position and binding all complete upto plinth & above plinth level.
4 5.22.6 Thermo-Mechanically Treated bars. Kg 1,600.00 107.85 1,72,560.00
Providing and laying in position machine batched and machine mixed design mix M-
25 grade cement concrete for reinforced cement concrete work, using cement
content as per approved design mix, including pumping of concrete to site of laying
5 5.33 but excluding the cost of centering, shuttering, finishing and reinforcement,
including admixtures in recommended proportions as per IS: 9103 to accelerate,
retard setting of concrete, improve workability without impairing strength and
durability as per direction of Engineer-in- charge.
All works above plinth level upto floor V level. Concrete of M25 grade with
minimum cement content of 330 kg /cum
Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth
level up to floor V level in all shapes and sizes in :
6.1 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 22.00 9,105.95 2,00,330.90
7 13.3 20 mm cement plaster of mix :
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives
of required shade:
New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including
priming coat of exterior primer applied @ 2.20 kg/10 sqm)
Steel work welded in built up sections/ framed work, including cutting, hoisting,
9 10.25 fixing in position and applying a priming coat of approved steel primer using
structural steel etc. as required.
9.1 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Kg 1,035.00 172.60 1,78,641.00
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne
capacity after excavating earth to an average of 22.5 cm depth, dressing to camber
and consolidating with road roller including making good the undulations etc. and
re- olling the sub grade and disposal of surplus earthwith lead upto 50 metres.
11 16.3 Supplying and stacking at site.
Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC
pavements after making the joints dust free with high pressure air jet cleaners, all
complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall
be made of bitumen hot sealing compound impregnated fibre board having
impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834
for hot sealing bitumen compound grade A.)
Providing and filling in position rubberized bitumen hot sealing compound for
13 16.46 sealing of expansion joints in roads / pavements all complete as per direction of the
Engineer-in-Charge.
13.1 16.46.1 Using grade 'A' sealing compound conforming to IS: 1834. per cm width 8.67 120.00 1,040.40
Providing, laying, spreading and compacting graded stone aggregate (size range
53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including
14 16.79 premixing the material with water at OMC in for all leads & lifts, laying in uniform Cum 150.00 2,914.30 4,37,145.00
layers with mechanical paverfinisher in sub- base / base course on well prepared
surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe
desired density, complete as per specifications and directions of Engineer-in-
Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from
batching plant. The ready mixed concrete shall be laid and finished with screed
15 16.75 board vibrator , vacuum dewatering process and finally finished by floating, Cum 320.00 9,823.80 31,43,616.00
brooming with wire brush etc. complete as per specifications and directions of
Engineer-incharge. (The panel shuttering work shall be paid for separately).
Sign of Contractor Page 11 of 52 NBCC
Digitally signed by ANUJ
S.NO Description Unit Qty Amount in Amount in
Construction of dry lean cement concrete sub base over a prepared sub-grade with
coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not
exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation
after blending to be as per specifications, cement content not to be less than 150
16 16.80 Kg/cum, optimum moisture content to be determined during trial length Cum 160.00 4,148.65 6,63,784.00
construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a
batching plant, transported to site, for all leads & lifts, laid with a mechanical paver,
compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as
per direction of Engineer-in-charge.
TOTAL (Carried Over to Summary of Civil Works) 61,24,954.31 -
Sign of Contractor Page 12 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
A SH-18.0 WATER SUPPLY & SANITARY
1 Constructing brick masonry manhole size 90x80 cm and 0.90 cm depth.
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement :
4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5
coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal
size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-
III) : 8 graded stone aggregate 40 mm nominal size), inside plastering
12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)
finished with floating coat of neat cement and making channels in
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) finished with a floating coat of neat
cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame
(light duty) 455x610 mm internal dimensions, total weight of cover and
frame to be not less than 38 kg (weight of cover 23 kg and weight of
1.3 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designationNos.
Extra for additional 45 cm depth for 90x80 cm manhole With common
burnt clay F.P.S. (non modular) bricks of class designation 7.5
Constructing brick masonry manhole size 0.91 m internal dia and 1.5 m
Constructing brick masonry circular type manhole 0.91 m internal dia at
bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse
sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1
cement : 3 coarse sand) finished with a floating coat of neat cement,
2.1 19.9 foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded
stone aggregate 40 mm nominal size), and making necessary channel
in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) finished with a floating coat of neat
cement, all complete as per standard design :
0.91 m deep with S.F .R.C. cover and frame (heavy duty , HD-20 grade
designation) 560 mm internal diameter conforming to I.S. 12592, total
weight of cover and frame to be not less than 182 kg., fixed in cement
2.2 19.9.1 concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size) including centering, shuttering all complete.
(Excavation, foot rests and 12mm thick cement plaster at the external
surface shall be paid for separately) :
2.3 19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of class designationNos.
Extra 0.6 cm depth for circular type manhole 0.91m internal dia (at
2.4 19.10.1 bottom) beyond 0.91 m to 1.67 m, With common burnt clay F.P.S. (non RM 15.00 7,591.80 1,13,877.00
modular) bricks of class designation 7.5
Constructing brick masonry chamber size 455x610 mm internal dimensions
3 and up to 0.9 m depth.
Constructing brick masonry chamber for underground C.I. inspection
chamber and bends with bricks in cement mortar 1:4 (1 cement : 4
coarse sand) C.I. cover with frame (light duty) 455x610 mm internal
dimensions, total weight of cover with frame to be not less than 38 kg
(weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with
3.1 19.3 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20
mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand :
10 graded stone aggregate 40 mm nominal size), inside plastering 12
mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished
smooth with a floating coat of neat cement on walls and bed concrete
etc. complete as per standard design:
3.2 19.3.1 Inside dimensions 455x610 mm and 45 cm deep for single pipe line :
3.3 19.3.1.1 With common burnt clay F.P.S. (non modular) bricks of class designationNos.
Extra for additional 45 cm depth for 455x610 mm masonry chamber
3.4 19.31.1.1 With common burnt clay F.P.S. (non modular) bricks of class RM 29.70 6,117.00 1,81,674.90
designation 7.5
Providing and fixing square-mouth S.W. gully trap class SP-1 complete
with C.I. grating brick masonry chamber with water tight C.I. cover with
4 19.4 frame of 300 x 300 mm size (inside) the weight of cover to be not less
than 4.50 kg and frame to be not less than 2.70 kg as per standard
150 x 100 mm size P type With common burnt clay F.P.S. (non
modular) bricks of class designation 7.5
Sign of Contractor Page 13 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
Supply and fixing of 4" Nahany Trap with Jali uPVC/SWR Pipe fittings
as per site requirements with standard practice for all floors including
cost and conveyance of all materials to site, labour charges, overheads
& contractors profit etc., complete for finish item of work.
Providing and fixing white vitreous china pedestal type water closet
(European type) with seat and lid, 10 litre low level white vitreous china
flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm
6 17.3 flush bend, overflow arrangement with specials of standard make and
mosquito proof coupling of approved municipal design complete,
including painting of fittings and brackets, cutting and making good the
walls and floors wherever required :
6.1 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid Nos. 97.00 8,006.60 7,76,640.20
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require:
White Vitreous China Wash basin size 550x400 mm with a pair of 15
mm C.P. brass pillar taps
Providing and fixing 15 mm nominal bore uplasticised PVC connection
pipe with brass unions
Providing and fixing 15 mm nominal bore C.P. brass angle valve for
7.3 18.53.1 basin mixer and geyser points of approved quality conforming to Nos. 237.00 574.30 1,36,109.10
Providing and fixing P.V.C. waste pipe of 32 mm dia for sink or wash
basin including P.V.C. waste fittings complete.
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require:
White Vitreous China Wash basin size 630x450 mm with a single 15
mm C.P. brass pillar tap
Providing and fixing CP soap Dish Holder having length of 138 mm,
9 NDSR 2 breadth 102 mm, height of 75 mm with concealed fitting arrangements, Nos. 119.00 111.45 13,262.55
weighing not less than 106 gms.
Providing and fixing CP towel rail complete with brackets fixed to
wooden cleats with CP brass screws with concealed fittings
10 NDSR 3 arrangement of approved quality and colour. Nos. 22.00 852.13 18,746.92
600 mm long towel rail with total length of 645 mm, width 78 mm and
effective height of 88mm, weighing not less than 190 gms.
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1
11 17.16A metre long with S.S. triangular plate to Eureopean type W.C. of quality Nos. 97.00 349.15 33,867.55
and make as approved by Engineer - in - charge.
Providing and fixing C.P. brass bib cock of approved quality conforming
Providing and fixing white vitreous china flat back half stall urinal of size
580x380x350 mm with white PVC automatic flushing cistern, with
fittings, standard size C.P. brass flush pipe, spreaders with unions and
clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap
with outlet grating and other couplings in C.P. brass, including painting
of fittings and cutting and making good the walls and floors wherever
required:Single half stall urinal with 5 litre P.V.C. automatic flushing
Supplying and fixing of SWR type PVC pipes (as per ISI standards) 6
Kg/Sq.cm. and fixing all special such as plain bends, off sets, door
bends, single junctions, double junctions as per site requirement, fixing
with PVC clamps if necessary with required number of Bombay nails
including cost and conveyance of all materials to site, labour charges
etc. complete for finished item of work at all floor levels.
Sign of Contractor Page 14 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all CPVC
15 18.8 plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m
spacing. This includes jointing of pipes & fittings with one step CPVC
18.8.2 20 cement and
mm nominal the cost of cutting chases and making good the
Sign of Contractor Page 15 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply including all CPVC
16 18.9 plain & brass threaded fittings This includes jointing of pipes & fittings
with one step CPVC solvent cement, trenching, refilling & testing of
joints complete as per direction of Engineer in Charge. External work.
Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete :
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank, IS : 12701 marked, with cover and suitable locking
arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank.
Supplying and fixing of PVC pipes 4 Kg/Sq.cm. and fixing all special
such as plain bends, off sets, door bends, single junctions, double
junctions as per site requirement, including cost and conveyance of all
materials to site, labour charges etc. complete for finished item of work.
Supply and fixing of 16mm to 20mm thick polished marble slab
partitioins of size 4'0"x2'0" for urinals including full rounding the edges,
20 NDSR 8 fixing in position, polishing, including cost and conveyance of all Nos. 53.00 2,386.00 1,26,458.00
materials and labour charges, overheads & contractors profit complete
for finished item of work for all floors.
Providing and fixing gun metal gate valve with C.I. wheel of approved
21 18.17 quality screwed end
18.17.1A 20 mm nominal bore Eac 34.00 539.95
18.17.2 32 mm nominal bore. Eac 16.00 689.60
Providing and fixing mirror of superior glass (of approved quality) and of
required shape and size with plastic moulded frame of approved make
22 17.32 and shade with 6 mm thick hard board backing :
17.32.3 Oval shape 450x350 mm (outer dimensions) Eac 1377.10
17.32.3 Rectangular shape 1500x450 mm Eac 2093.00
23 17.34 Providing and fixing toilet paper holder :
Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C.
pipes including collars/ spigot jointed with stiff mixture of cement mortar
in the proportion of 1:2 (1 cement : 2 fine sand) including testing of
joints etc. complete
Providing orange colour safety foot rest of minimum 6 mm thick plastic
encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to
IS: 1786, having minimum cross section as 23 mmx25 mm and over all
minimum length 263 mm and width as 165 mm with minimum 1 12 mm
space between protruded legs having 2 mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard drawing and Eac
suitable to with stand the bend test and chemical resistance test as per h
specifications and having manufacture's permanent identification mark
to be visible even after fixing, including fixing in manholes with
30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand :
6 graded stone aggregate 20 mm nominal size) complete as per
Providing and fixing unplasticised - PVC pipe clips of approved design
to unplasticised - PVC rain water pipes by means of 50x50x50 mm
12.43 hard wood plugs, screwed with M.S. screws of required length,
including cutting brick work and fixing in cement mortar 1:4 (1 cement :
4 coarse sand) and making good the wall etc. complete.
Sign of Contractor Page 16 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
Sign of Contractor Page 17 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
Providing and fixing to the inlet mouth of rain water pipe PTMT (an
Engineering Thermoplastic) grating square (Slit) 150 mm square with a
height of 8 mm and weighing not less than 100 gms.
Providing and fixing on wall face unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type A, including jointing with seal ring
28 12.41 conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)
Single socketed pipes.
(i)Single socketed pipes.
Supply, Installation, Testing & Commissioning of a 250 LPH Reverse
Osmosis (RO) Plant, including high-rejection TFC RO membranes,
complete pre-treatment system (sand filter, carbon filter, micron
29 NDSR 10 filtration), dosing systems (antiscalant and pH correction), and required Nos. 1.00 3,50,000.00 3,50,000.00
electrical connections with suitable power supply. The scope includes
all necessary mechanical, electrical, and instrumentation work for fully
functional and efficient operation.
Note:- Payment shall be as per GST Tax Invoice with contractor over
rates as per CPWD rate analysis.
B BORE WELL AND PUMP SET
Boring/drilling bore well of required dia for casing/ strainer pipe, by
suitable method prescribed in IS: 2800 (part I), including collecting
samples from different strata, preparing and submitting strata chart/
bore log, including hire & running charges of all equipments, tools,
plants & machineries required for the job, all complete as per direction
of Engineer -in-charge, upto 90 metre depth below ground level.
1.1 23.1.1 All types of soil
Supplying, assembling, lowering and fixing in vertical position in bore
well, unplasticized PVC medium well casing (CM) pipe of required dia,
conforming to IS: 12818, including required hire and labour charges,
fittings & accessories etc. all complete, for all depths, as per direction
Engineer -in-charge.
Supplying, assembling, lowering and fixing in vertical position in bore
well unplasticized PVC medium well screen (RMS) pipes with ribs,
3 23.4 conforming to IS: 12818, including hire & labour charges, fittings &
accessories etc. all complete, for all depths, as per direction of
Engineer-in-charge.
Providing and fixing suitable size threaded mild steel cap or spot
4 23.13 welded plate to the top of bore well housing/ casing pipe, removable as Nos. 3.00 246.00 738.00
per requirement, all complete for bore well of:
Providing and fixing M.S. clamp of required dia to the top of casing/
5 23.14.2 housing pipe of tubewell as per IS: 2800 (part I), including necessary Nos. 3.00 2,019.00 6,057.00
bolts & nuts of required size complete.
Providing and fixing Polyethylene- Aluminium- Polyethylene (PE-AL-
PE) Composite Pressure Pipes conforming to IS - 15450, U.V.
stabilized with carbon black having thermal stability for hot & cold water
supply, capable to withstand temperature up to 80°C including all
special fittings of composite material (engineering plastic blend and
brass inserts wherever required ) e.g. elbows, tees, reducers, couplers
& connectors etc. with trenching, refilling and testing of joints complete
as per direction of the engineer in charge : External work
Supply of 3 Core 2.5 Sq mm ISI marked Flat Copper cable of ISI for
Submersible Motors confirming to IS: 694:1990.
Fabrication , transportation and supply of suitable size panel board for
single phase submersible motor 2 to 3HP consisting of relay,
8 NDSR 13 Contactor, starting and running capacitors, Voltmeter, Ammeter, Nos. 3.00 7,260.00 21,780.00
indicator lamps, MCB , on/off switch including supply and fixing of DOL
starter of complete.,
Sign of Contractor Page 18 of 52 NBCC
Digitally signed by ANUJ
Ref. DSR Non DSR
Sl No Description Unit Qty Rate
(DSR- Amount in Rs. Amount in Rs.
Supply and Transportation of 2HP 5star rated submersible motor
pumpset, confirming to IS 8034 and motor confirming to IS 9283 with
waterproof winding, pump shall be suitable for various delivery head
and discharge with stainless steel shaft motor suitable for working on
240V ± 10%, single phase 50 Hz AC supply, etc complete for 4" Bore
GRAND TOTAL CARRIED TO SUMMARY 81,98,850.73 40,39,802.47
GRAND TOTAL CARRIED TO SUMMARY 81,98,850.73 40,39,802.47
Sign of Contractor Page 19 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING
XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
Ref. DSR Amount Non DSR Amount
S.NO Description Unit Qty Rate in Rs.
(DSR- in Rs. in Rs.
A HORTICULTURE AND LAND SCAPING (SOFTSCAPE)
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and
trenching the excavated base to a further depth of 30 cm, refilling the excavated
earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8
parts of stacked volume of earth after reduction by 20% : one part of stacked
volume of sludge or manure after reduction by 8%), flooding with water, filling with
1 NDSR 1 earth if necessary, watering and finally fine dressing, leveling etc. including stacking Sqm 1,000.00 438.12 4,38,120.00
and disposal of materials declared unserviceable and surplus earth by spreading
and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of
sludge, manure or extra earth to be paid for separately)
Supplying and stacking at site dump manure from approved source, including
2 2.4 carriage upto 5 km lead complete (manure measured in stacks will be reduced by
8% for payment) :
2.4.1 Screened through sieve of I.S. designation 20 mm Cum 100.00 245.15 24,515.00
2.4.2 Screened through sieve of I.S. designation 16 mm Cum 100.00 290.70 29,070.00
2.4.3 Screened through sieve of I.S. designation 4.75 mm Cum 100.00 319.90 31,990.00
Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm
thickness of existing ground prepared with proper level and ramming with tools
wooden (Dhurmos) and than rolling the surface with light roller make
2 2.33 the surface smoothen and light waterning with sprinkler and maintenance for 30 Sqm 800.00 214.40 1,71,520.00
days or more till the grass establish properly, as per direction of officer-in-charge.
Complete maintenance of the entire garden features having as per yard stick in the
garden area i.e. lawn trees, shrubs, edge, flower beds, foliages, creepers etc.
including hoeing,weeding pruning replacement of plants, gap
filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter,
3 2.39 removal of garden waste, applying insecticide, pesticide & fertilizers(whenever
required) top dressing of lawn with good earth and menure and maintenance of
other garden related works as directed by office-in-charge (Cost of Good Earth,
Manure, Fertilizer, Insecticide, Pesticide, lawn mover and brush cutter with fuel &
other T & P material/ articles shall be provided by the department.)
Supply of trees/ plants/palms/shrubs like Antirrhinum dwarf etc plants. Bag size
Supply of trees/ plants/palms/shrubs like Antirrhinum dwarf etc plants. Bag size
6 NDSR 4 Cast Iron Benches LS 2,00,000.00
Note:- Payment shall be as per GST Tax Invoice with contractor over rates as per
CPWD rate analysis.
Spreading of sludge, dump manure and/or good earth in required thickness as per
direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be
paid separately).
Mixing earth and sludge or manure in the required proportion specified or
3 2.9 directed by the Officer-in-charge Cum 50.00 36.55 1,827.50
TOTAL (Carried Over to Summary of Civil Works) 12,58,760.00 11,65,120.00
Sign of Contractor Page 20 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL
DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
Court Rate in DSR NON DSR
S.NO (DSR- Description Unit (QTY.) Rs. Amount in Rs. Amount in Rs.
A SH. FURNITURE WORKS
Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998
marked, with one side decorative lamination other side balancing lamination Grade-
1 9.157.1 I(exterior grade) in shelves with screws and fittings wherever required, edges to be Sqm 184.20 10,000.00 18,42,000.00
sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be
paid separately).
Furniture and Furnishing required for Office use are to be procured and installed
under this head. Vendor is required to submit floor wise detailed furniture layout with
2-3 options giving the type, quantity etc before start of procurement. These furniture
lay-outs including the type of furniture, specifications, shades/colour scheme,
quantity etc will be finalised as per the requirement of NBCC/Client during currency
of contract. Accordingly, the contractor shall procure and install the furniture and
The amount earmarked under Furniture Works head of payment schedule shall be LS - 2,00,00,000.00
treated as a lumpsum amount/Provisional sum. The actual payment shall be made
as per the type, spcifications & quantities as procured & installed as Extra items from
this Lumpsum amount/Provisional sum. Note: GST tax invoice will only be
considered for payments. No other receipts are allowed.
On supply of Equipment / Materials & all other accessories - 75%
On installation - 15%
On completion and handling over the end user. - 10%
Note:- Payment shall be as per GST Tax Invoice with contractor over rates as per
CPWD rate analysis.
TOTAL (Carried Over to Summary of Civil Works) 18,42,000.00 2,00,00,000.00
Sign of Contractor Page 21 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX
COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT,
COST OF EXTERNAL ELECTRICAL WORK
S. DSR(2022 ) DSR(2025 ) Non DSR
Description of item
No. Amount in Rs. Amount in Rs. Amount in Rs.
1 POWER DISRIBUTION SYSTEM - 3,74,776.00 33,07,000.00
3 TRANSFORMER - 11,79,071.00 -
6 MISCELLANEOUS ITEMS - - 99,900.00
COST OF INTERNAL ELECTRICAL WORK
1 PVC & STEEL CONDUITS 13,99,193.32 - -
2 INTERNAL WIRING: 59,46,976.00 - -
3 SWITCH SOCKETS: 4,29,509.00 - -
4 DISTRIBUTION BOARDS 12,18,740.00 - -
6 HOT DEEP GI CABLE TRAYS & GI 1,60,615.00 - 8,64,716.97
7 EARTHING & LIGHTNING 4,05,870.00 - 4,900.00
8 LIGHTING FIXTURE AND FANS - 13,87,255.00 11,01,094.00
9 UPS / INVERTER - 3,41,772.00 -
GRAND TOTAL CARRIED TO SUMMARY 1,18,24,647.32 55,62,874.00 72,82,965.98
GRAND TOTAL CARRIED TO SUMMARY 1,18,24,647.32 55,62,874.00 72,82,965.98
Sign of Contractor Page 22 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT
GUDIVADA, KRISHNA DISTRICT, A.P".
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
1 PVC & STEEL CONDUITS
Supplying and fixing of following sizes of steel conduit along with
accessories in surface/recess including painting in case of surface
conduit, or cutting the wall and making good the same in case of
recessed conduit as required.
Supplying and fixing of following sizes of medium class PVC conduit
along with accessories in surface/recess including cutting the wall
and making good the same in case of recessed conduit as required.
Providing and fixing circular/hexagonal Fan box cast iron /metal
sheet Box for ceiling fan clamp of internal dia 140mm , 73 mm
height,Top id of 1.5mm thick MS sheet with its Top surface hacked
1.7 Civil 10.18 of proper bonding top lid shall be screwed into cast iron /metal No. 240.00 185.20 44,448.00
sheet Box by mean of 3.3mm dia round headed screw one lock at
the corners.clamp shall be made of 12mm dia ms Bar band toshape
as per standrd drawing.
TOTAL CARRIED TO ELECTRICAL SUMMARY 13,99,193.32 - -
2 INTERNAL WIRING:
Wiring for light point/ fan point/ exhaust fan point/ call bell point
with 1.5 sq.mm FRLS PVC insulated copper conductor single core
2.1 cable in surface / recessed steel conduit, with modular switch,
modular plate, suitable Gl box and earthing the point with PVC
insulated copper conductor single core cable etc. as required.
Wiring for twin control light point with insulated copper conductor
single core cable in surface / recessed steel conduit, 2 way modular
2.2 1.4 switch, modular plate, suitable Gl box and earthing the point with POINT 30.00 1,981.00 59,430.00
1.5 sq.mm. FRLS PVC insulated copper conductor single core cable
etc .as required.
Wiring for group controlled (looped) light point/fan point/exhaust
fan point/ call bell point (without independent switch etc.) with 1.5
sq. mm FRLS PVC insulated copper conductor single core cable in
surface/ recessed PVC conduit, and earthing the point with 1.5 sq.
mm FRLS PVC insulated copper conductor single core cable etc. as
Wiring for circuit/ submain wiring along with earth wire with the
2.4 1.14 following sizes of FRLS PVC insulated copper conductor, single core
cable in surface/ recessed medium class PVC conduit as required.
Supplying and drawing following sizes of FRLS PVC insulated copper
2.5 conductor, single core cable in the existing surface/ recessed steel/
PVC conduit as required.
TOTAL CARRIED TO ELECTRICAL SUMMARY 59,46,976.00 - -
3 SWITCH SOCKETS:
Supplying and fixing following modular switch/ socket on the
3.1 existing modular plate & switch box including connections but
excluding modular plate etc. as required.
Supplying and fixing two module stepped type electronic fan
3.2 1.25 regulator on the existing modular plate switch box including No. 240.00 369.00 88,560.00
connections but excluding modular plate etc. as required.
Supplying and fixing modular blanking plate on the existing
modular plate & switch box excluding modular plate as required.
Sign of Contractor Page 23 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
Supplying and fixing following size/ modules, Gl box along with
modular base & cover plate for modular switches in recess etc. as
Supplying and fixing following Modular base & cover plate on
existing modular metal boxes etc. as required.
Supplying and fixing suitable size Gl box with modular plate and
cover in front on surface or in recess, including providing and fixing
3 pin 5/6 A modular socket outlet and 5/6 A modular switch,
connections etc. as required.
Supplying and fixing suitable size Gl box with modular plate and
cover in front on surface or in recess, including providing and fixing
6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular
switch, connections etc. as required.
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction
box/ wooden block including connections etc. as required.
Supplying and fixing brass batten/ angle holder including
connection etc. as required.
Supplying and fixing call bell/ buzzer suitable for single phase, V,
complete as required.
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providng and fixing
3.11 1.56 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular No. 80.00 676.00 54,080.00
switch, connections etc. as required. (For light plugs to be used in
non residential buildings).
Supplying & fixing suitable size Gl box with modular plate and cover
in fronton surface or in recess including providing and fixing 25 A
modular socket outlet and 25 A modular SP MCB, "C" curve
including connections, painting etc. as required.
Supplying and fixing 20/32 A, 240 V, SPN Industrial type socket
outlet, with 2 pole and earth, metal enclosed plug top alongwith 20
3.13 2.18 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in No. 20.00 1,621.00 32,420.00
recess, with chained metal cover for the socket outlet and
complete with connections, testing and commissioning etc. as
Installation, testing and commissioning of ceiling fan, including
wiring the down rods of standard length (up to 30 cm) with 1.5 sq.
mm FRLS PVC insulated, copper conductor, single core cable etc. as
Supplying and fixing extra conduit down rod of 20 cm length G.l.
pipe 15 mm dia, heavy gauge including painting etc. as required.
(Note : More than 5 cm length shall be rounded to the nearest 10
cm and 5 cm or less shall be ignored)
TOTAL CARRIED TO ELECTRICAL SUMMARY 4,29,509.00 - -
4.00 DISTRIBUTION BOARDS
Supplying and fixing following way, single pole and neutral, sheet
steel, MCB distribution board, 240 V, on surface/ recess, complete
4.1 2.3 with tinned copper bus bar, neutral bus bar, earth bar, din bar,
interconnections, powder painted including earthing etc. as
required. (But without MCB/RCCB/Isolator)
Supplying and fixing following way, horizontal type three pole and
neutral, sheet steel, MCB distribution board, 415 V, on surface/
4.2 2.4 recess, complete with tinned copper bus bar, neutral bus bar, earth
bar, din bar, interconnections, powder painted including earthing
etc. as required. (But without MCB/RCCB/Isolator)
Supplying and fixing of following ways surface/ recess mounting,
vertical type, 415 V, TPN MCB distribution board of sheet steel,
dust protected, duly powder painted, inclusive of 200 A tinned
4.3 2.5 copper bus bar, common neutral link, earth bar, din bar for
mounting MCBs (but without MCBs and incomer) as required .
(Note : Vertical type MCB TPDB is normally used where 3 phase
outlets are required.)
Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' series,
miniature circuit breaker suitable for inductive load of following
poles in the existing MCB DB complete with connections, testing
and commissioning etc. as required.
b 2.10.2 Single pole and neutral No. RTO 599.00
Supplying and fixing single pole blanking plate in the existing MCB
DB complete etc. as required.
Sign of Contractor Page 24 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
Supplying and fixing following rating, double pole, (single phase and
neutral), 240 V, residual current circuit breaker (RCCB), having a
sensitivity current 30 mA in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
Supplying and fixing following rating, double pole, the existing MCB
4.7 2.12 DB complete with connections, testing and commissioning etc. as
Supplying and fixing following rating, four pole, 415 V, isolator in
4.7 2.13 the existing MCB DB complete with connections, testing and
commissioning etc. as required.
Providing and fixing following rating and breaking capacity and pole
MCCB with thermomagnetic release and terminal spreaders in
existing cubicle panel board including drilling holes in cubicle panel,
making connections, etc. as required.
Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet,
with 4 pole and earth, metal enclosed plug top along with 30 A "C"
4.9 2.20 curve, TPMCB, in sheet steel enclosure, on surface or in recess, No. 21.00 4,107.00 86,247.00
with chained metal cover for the socket out let and complete with
connections, testing and commissioning etc. as required.
TOTAL CARRIED TO ELECTRICAL SUMMARY 12,18,740.00 - -
5.0 LT CABLES:
Supply,testing and commissioning of following sizes of XLPE
Insulated, cores laid up, PVC tape/Extruded Inner
5.1 sheathed,galvanised steel strip armoured, Extruded PVC Type ST2
Sheathed, Aluminium / Copper conductor 1.1 KV grade cable as per
IS 7098(Part 1) 1988
a NDSR 1 4C x 10 sq.mm Cu Armoured cable RMT 150.00 630.36 94,554.15
b NDSR 2 4C x 6 sq.mm Cu Armoured cable RMT 100.00 429.86 42,986.20
c NDSR 3 3C x 6 sq.mm Cu Armoured cable RMT 50.00 369.86 18,493.15
d NDSR 4 4C x 10 sq.mm Alu XLPE Armoured cable. RMT 120.00 250.00 30,000.00
e NDSR 5 3.5C x 35 sq.mm Alu XLPE Armoured cable. RMT 40.00 400.00 16,000.00
f NDSR 6 3.5C x 120 sq.mm Alu XLPE Armoured cable. RMT 75.00 835.00 62,625.00
g NDSR 7 3.5C x 185 sq.mm Alu XLPE Armoured cable. RMT 150.00 1,343.00 2,01,450.00
Laying of one number PVC insulated and PVC sheathed / XLPE
power cable of 1.1 KV grade of following size direct in ground
including excavation, sand cushioning, protective covering and
refilling the trench etc as required.
c 7.1.3 Above 95 sq. mm and up to 185 sq. mm RMT 150.00 422.00 63,300.00
Laying and fixing of one number PVC insulated and PVC sheathed /
5.3 XLPE power cable of 1.1 KV grade of following size on wall surface
a 7.8.1 Up to 35 sq. mm (clamped with 1mm thick saddle) RMT 460.00 45.00 20,700.00
Above 95 sq. mm and up to 185 sq. mm (clamped with 25/40x3mm
Supplying and making end termination with brass compression
gland and aluminium lugs for following size of PVC insulated and
PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as
Supplying, installing on wall or suspension on ceiling, testing and
commissioning of following capacity Air Insulated Compact Type
Bus Trunking for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply
with metal clad enclosure having IP-54 rating after fixing the tap off
boxes and all accessories, made of 1.6mm thick steel sheet duly
powder coated in convenient sections complete with 4 Nos
aluminium bus bars having current density of 130 A/ sq cm at
nominal current rating, necessary joints, elbow joints & expansion
joints, fire barrier at each floor, continuous earthing with 2 Nos
aluminium strip of suitable size (one on each side) including, G.l.
clamping brackets, suspenders, angle iron bracket, steel fasteners,
connecting to earthing system etc. as required.
Sign of Contractor Page 25 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
Supplying, installation, testing & commissioning of following
capacity Plug In/ tap off box on the existing Air Insulated Compact
Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts,
50Hz A.C. supply made with 1.6mm thick sheet steel enclosure
(IP54) duly powder coated with provision of MCCB/ACB (but
without MCCB/ACB) complete etc. as required
e 3.12.5 500 A, lsc= 50kA for 1 sec Each - 16012.00
f 3.12.6 630 A, lsc= 50kA for 1 sec Each - 16012.00
Supplying, installing by suspension on ceiling, testing and
commissioning of following capacity Sandwich Type Rising Mains
for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal
clad enclosure having IP-54 rating after fixing the tap off boxes and
all accessories, made of 1.6mm thick steel sheet duly powder
coated in convenient sections complete with 4 Nos aluminium bus
5.7 bars having current density of 130 A/ sq cm at nominal current
rating, necessary joints, elbow joints & expansion joints and bends,
fire barrier at each floor, provision of tapping at every metre,
adopter box and copper flexible for joints, continuous earthing with
2 Nos aluminium strip of suitable size (one on each side) including,
G.l. clamping brackets, suspenders, angle iron bracket, steel
fasteners, connecting to earthing system etc. as required
c 3.13.3 630 A, lsc= 50kA for 1 sec Each - 19211.00
d 3.13.4 800 A, lsc= 50kA for 1 sec Each - 21714.00
TOTAL CARRIED TO ELECTRICAL SUMMARY 21,47,589.00 - 4,66,108.50
6.0 HOT DEEP GI CABLE TRAYS & GI RACEWAYS
Supplying and installing following size of perforated Hot Dipped
Galvanised Iron cable tray (galvanisation thickness not less than 50
6.1 4.6 microns) with perforation not more than 17.5%, in convenient
sections, joined with connectors, suspended from the ceiling with
G.I. suspenders including G.I. bolts & nuts, etc. as required.
a 4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness RMT 15.00 716.00 10,740.00
b 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness RMT 15.00 963.00 14,445.00
c 4.6.6 450 mm width X 50 mm depth X 2.0 mm thickness RMT 20.00 1,325.00 26,500.00
d 4.6.11 600 mm width X 50 mm depth X 2.0 mm thickness RMT 30.00 1,909.00 57,270.00
Supplying and installing following size of perforated Hot Dipped
Galvanised Iron cable tray "bends" (Galvanisation not less than 50
6.2 microns) with perforation not more than 17.5%, in convenient
sections, joined with connectors, suspended from the ceiling with
G.l. suspenders including G.l. bolts & nuts, etc. as required.
a 4.7.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 2.00 1270.00 2,540.00
b 4.7.4 300 mm width X 50 mm depth X 1.6 mm thickness Each 2.00 1852.00 3,704.00
c 4.7.6 450 mm width X 50 mm depth X 2.0 mm thickness Each 3.00 2683.00 8,049.00
d 4.7.7 600 mm width X 50 mm depth X 2.0 mm thickness Each 3.00 3774.00 11,322.00
Supplying and installing following size of perforated Hot Dipped
Galvanised Iron cable tray "Tee" (Galvanisation not less than 50
6.3 microns) with perforation not more than 17.5%, in convenient
sections, joined with connectors, suspended from the ceiling with
G.l. suspenders including G.l. bolts & nuts, etc. as required.
a 4.8.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 1.00 1383.00 1,383.00
b 4.8.4 300 mm width X 50 mm depth X 1.6 mm thickness Each 1.00 2156.00 2,156.00
c 4.8.6 450 mm width X 50 mm depth X 2.0 mm thickness Each 2.00 3141.00 6,282.00
d 4.8.7 600 mm width X 50 mm depth X 2.0 mm thickness Each 1.00 4446.00 4,446.00
Supplying and installing following size of perforated Hot Dipped
Galvanised Iron cable tray "Cross member" (Galvanisation not less
than 50 microns) with perforation not more than 17.5%, in
convenient sections, joined with connectors, suspended from the
ceiling with G.l. suspenders including G.l. bolts & nuts, etc as
a 4.9.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 1.00 1383.00 1,383.00
b 4.9.4 300 mm width X 50 mm depth X 1.6 mm thickness Each 1.00 2366.00 2,366.00
c 4.9.6 450 mm width X 50 mm depth X 2.0 mm thickness Each 1.00 3569.00 3,569.00
d 4.9.7 600 mm width X 50 mm depth X 2.0 mm thickness Each 1.00 4460.00 4,460.00
Sign of Contractor Page 26 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
Supplying and instalation, in floor including chase cutting of
floor,leveling, refilling and making good the same from 1.6 mm
thick and 2 mm thick cover pregalvanised MS CRCA sheet, totally
enclosed, height 40 mm. The two lengths of raceways shall be
fitted with Collars, 50 mm wide, 3 mm thick , press fit type. The
raceways shall be clamped to the floor slab with GI clamps, 3mm
thick and shall be screwed to the floor slab. The joint between
raceway and junction box will be made with GI flexible strip( 3 nos),
3 mm thick, 4 inches long ,15 mm wide which will be nut bolted to
the Junction box complete as required etc.
a NDSR 8 300 mm (wide) x 38 mm (height) RMts 400 1295.73 5,18,291.20
b NDSR 9 225 mm (wide) x 38 mm (height) RMts 110 1105.61 1,21,617.10
c NDSR 10 100 mm (wide) x 38 mm (height) RMts 110 728.99 80,188.35
Fabricating supplying to site of installation, 2 mm thick MS sheet
steel power coated 5 sided junction boxes with 2.0 mm thick GI
Sheet Cover including providing rubber gasket between the cover
6.6 and the junction box, brass screws height as per site condition and
totally enclosed, welded. the channel and junction box shall be
seam welded together to make it dust and water proof. Proper
cutouts shall be made in the side walls for raceway entry.
TOTAL CARRIED TO ELECTRICAL SUMMARY 1,60,615.00 - 8,64,716.97
7.0 EARTHING & LIGHTNING CONDUCTOR
Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including
accessories, and providing masonry enclosure with cover plate
7.1 5.2 having locking arrangement and watering pipe etc. with charcoal/ No. 20.00 6,855.00 1,37,100.00
coke and salt as required.
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick
including accessories, and providing masonry enclosure with cover
plate having locking arrangement and watering pipe of 2.7 metre
long etc. with charcoal/ coke and salt as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick
including accessories, and providing masonry enclosure with cover
plate having locking arrangement and watering pipe of 2.7 metre
long etc. with charcoal/ coke and salt as required.
Providing and fixing 25 mm X 5 mm copper strip on surface or in
recess for connections etc. as required.
Providing & fixing of 25mm x 5mm GI strip on surface or recess for
earth connection as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for
loop earthing as required.
Providing and fixing 4.00 mm dia copper wire on surface or in
7.7 5.19 recess for loop earthing along with existing surface/ recessed RMT 120.00 127.00 15,240.00
conduit/submain wiring/cable as required.
Providing & fixing of 40mm x 6mm GI strip on surface or recess for
earth connection as required.
Providing and fixing of lightning conductor finial, made of 25 mm
7.9 6.2 dia 300 mm long, G.l. tube, having single prong at top, with 85 mm Nos 8.00 518.00 4,144.00
dia 6 mm thick G.l. base plate including holes etc. complete as
Jointing copper / G.l. tape (with another copper/ G I tape, base of
7.10 6.4 the finial or any other metallic object) by riveting / nut bolting/ Nos 50.00 113.00 5,650.00
sweating and soldering etc as required.
Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or
7.11 6.7 surface of wall for lightning conductor complete as required.(For RMT 350.00 126.00 44,100.00
horizontal run)
Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or
7.12 6.8 surface of wall for lightning conductor complete as required.(For RMT 128.00 197.00 25,216.00
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.l.
7.13 6.12 strip, 125 mm long, with 4 nos. of G.l. bolts, nuts, chuck nuts and Nos 8.00 121.00 968.00
spring washers etc. complete as required.
TOTAL CARRIED TO ELECTRICAL SUMMARY 4,05,870.00 4,900.00
Sign of Contractor Page 27 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
8.0 LIGHTING FIXTURE AND FANS
Supplying, installation, Testing & Commissioning of LED surface
mounted 24W Batten light of following body material and
construction as per IS : 10322 withdriver (Replaceable) as per the
requirement with Driver efficiency >85%, Operating voltage AC 140-
270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg
centigrade, internal surge protection of 2.5 KV with Short & Open
circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , Flicker
free (flicker should be below 5 %), life time (LED,Driver & electrical
circuitry), of minimum 50000 Burning Hours with , 70% of initial
Lumen maintained till life ends,CCT 3000°K / 4000°K / 5700°K
/6000°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color
Matching)<3, Maximum power consumption should not more than
8.1 1.10.2 (DSR- 2025) the specified ratingand Fixture shall be of relevant BIS standard and No. 390.00 738.00 2,87,820.00
trade mark certificate (T.C.). Manufactures Word Mark/ Name
Engraved/ Embossing/ Screen printing on housing. OEM must have
its own in house NABL lab setup for all testing facilities for LED
fixtures. complete in all respect i/c connections with 1.5 sq mm
FRLS, PVC insulated copper conductor single core cable and
earthing etc. as required with Minimum 5 year OEM warranty.
System lumen efficacy ≥120 <135 lm/Watt output . LM79 &
LM80Test report from NABL lab for all testing required for LED
fixtures as per BIS shall be submitted. Shape size and CCT shall be
as approved by Engineer-in-Charge as per requirement. (Thermal
management: heat sink of aluminium housing such that LED
junction temperature shall not rise above 90°C).
Supplying, installation, Testing & Commissioning of 36W Panel light
2x2 ft., of following body material and construction as per IS :
10322 with driver as per the requirement with Driver efficiency
>85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz,
Operating temp range -15 deg to 40 deg centigrade, internal surge
protection of 2.5 KV with Short & Open circuit protection ,THD <
10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19,
Flicker free, (flicker should be below 5 %), life time(LED,Driver &
electrical circuitry), of minimum 50000 Burning Hours with ,70% of
initial Lumen maintained till life ends,CCT 3000°K / 4000°K / 5700°K
/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color
Matching) <3, Maximum power consumption should not more than
the specified rating and Fixture shall be of relevant BIS standard
and trade mark certificate ( T.C.). Manufactures Word Mark/ Name
Engraved/ Embossing/ Screen printing on housing. complete in all
respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper
conductor single core cable and earthing etc. as required with
Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135
lm/Watt output . LM79 & LM80 Test report from NABL lab for all
testing required for LED fixtures as per BIS shall be submitted.
Shape size and CCT shall be as approved by Engineer-in-Charge as
per requirement. (Thermal management: heat sink of aluminium h
Supplying, installation, Testing & Commissioning of 12W LED
Recessed / surface Down lighter (Round / square/ Rectangular)
SMD type of following body material with PMMA and prismatic
diffuser and construction as per IS :10322 with driver as per the
requirement with Driver efficiency >85%,Operating voltage AC 140-
270 Volt, freq 50/60 hz, Operating temp range-15 deg to 40 deg
centigrade, internal surge protection of 2.5 KV withShort & Open
circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR
(Unified Glare Rating) < 19, Flicker free (flicker should be below 5
%), life time (LED,Driver & electrical circuitry), life time of minimum
50000 Burning Hours with , 70% of initial Lumen maintainedtill life
ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI
Bin), SDCM(Standard Deviation Color Matching) <3, Maximum
8.3 1.2.3 (DSR- 2025) power consumption should not more than the specified rating and No. 60.0 708.0 42480.0
Fixture shall be of relevant BIS standard and trade mark certificate (
T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/
Screen printing on housing. OEM must have its own in house NABL
lab setup for all testing facilities for LED fixtures. "complete in all
respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper
conductor single core cable and earthing etc. as required with
Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135
lm/Watt output . LM79 & LM80 Test report from NABL lab for all
testing required for LED fixtures as per BIS shall be submitted.
Shape size and CCT shall be as approved by Engineer-in-Charge as
per requirement. (Thermal management: heat sink of aluminum
housing such that LED junction temperature shall not rise above
Supply of 9W/10W LED Mirror Light fitting with decorative grey
8.4 NDSR 15 end caps, polycarbonate body and opal acrylic diffuser etc. No. 6.00 737.00 4,422.00
Makes: As per list of recommended brands.
Supply of 7w Lamp with input voltage 90 to 300V, Color
8.5 NDSR 16 temperature 3000k - 6500k, Beam angle 170 - 220 degrees, B22 No. 6.00 202.00 1,212.00
Sign of Contractor Page 28 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
Supply, Installation, Testing and Commissioning of 1200mm,
service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min
(Minimum) ceiling fan with Brush Less Direct Current (BLDC) Motor,
class of insulation: B, 3 nos. metal (Aluminum alloy) blades, 30 cm
long down rod, 2 nos. canopies, shackle kit, safety rope, copper
winding, steel/Al body Power Factor not less than 0.9, Service
Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS
: 374-2019), THD (Total Harmonic Distortion) less than 10%,
remote (preferably mobile app based) for speed control and all
remaining accessories including safety pin, nut bolts, washers,
temperature rise=75 degree C (max.), insulation resistance more
than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling
Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as
Supply and fixing of exhaust fan, steel body AC single Phase. 230V
of size 300m sweep with, blades, and frame and louvers
Supply and fixing of Wall fan, steel body AC single Phase. 230V of
size 450m sweep with, blades, and frame and louvers
Supplying, installation, Testing & Commissioning of Street light LED
fixture powder coated pressure die cast aluminum body with driver
as per the requirement with Driver efficiency >85%, Input voltage:
140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to
50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC
61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 ,
P. F.≥0.95, IP- 66,IK-10, CRI >80, under voltage and over voltage
protection, EMIEMC As per CISPR -15, lenses for beam angle as per
IESNA type I/II/III as
per the width of the road and the project requirement., suitable to
fit in up to 65mm dia pipe, life time (LED,Driver & electrical
circuitry) of minimum 50000 Burning Hours with 70% of initial
8.1 Lumen maintained till life ends as per LM80 extrapolation IES TM-
per ANSI Bin),SDCM(Standard Deviation Color Matching) <5,
Maximum power consumption should not more than the specified
rating and Fixture shall be of relevant BIS standard complete in all
respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper
conductor single core cable and earthing etc. as required with
Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120
lm/Watt output. LM79 & LM80 Test report from NABL lab for all
testing required for LED fixtures as per BIS shall be submitted.
Shape size and CCT shall be as approved by Engineer-in-Charge as
per requirement. (Thermal management: heat sink of aluminum
housing such that LED junction temperature shall not rise above
90 watt street Light No. 10.00 2,156.00 21,560.00
Fixing of LED Street Light Luminaire to the wall with 1.0 mtr 25mm
8.11 NDSR 19 dia Gi pipe bracket and anti tilting MS flat etc., Including giving No. 10.00 867.00 8,670.00
connections and labour charges etc., complete.
Supply and instalation of of following 6 mtr Street light single arm bracket
-Octagonal Hot diped GI pole including suitable foundation.(Top Dia
8.12 NDSR 20 70mm, Bottom dia -130mm and 3 mm thick sheet and base plate -220 x No. 10.00 23,580.00 2,35,800.00
220 x 16 mm, and Foundation bolts 700 mm x 20 mm).
FEEDER PANEL: Supply, fabrication, installation, testing and
commissioning of cubicle type front operated, IP65 Outdoor Feeder
Panel, dust and vermin proof cubicle chamber for mounting and suitable
for 415 V, 50 Hz, AC supply including supply and erection of all
switchgears. Panel fabricated with 14 SWG CRCA sheet steel enclosure,16
SWG CRCA Sheet steel for internal partitions including cutting, welding,
fabrication, including internal chamber fire barriers, door with gaskets
and locking facility, painting and cleaning after 7 tank process, panel of
required colour paint, suitable Aluminum busbars, SMC/DMC etc.,as
required including labour charges etc complete . The panel shall be
mounted on U channels grouted to the floor including all materials. All
the PCC/ Panels shall have at least two spare cubicles of the maximum
rating. All feeders shall be earthed with 2Nos GI flats of adequate size to
the main earth bus of 25 x 6mm GI flat.. Fuses shall be provided for
8.13 NDSR 21 Control purposes . MCCB MAKE: L&T ( DSINE), ABB(TMAX) No. 1.00 75,000.00 75,000.00
a) 100A,36KA,4P MCCB-1 No,
b) RYB indication lamps,
c) Dual source KWH energy meter with 3Nos.CT 100 /5A and selector
switch,3 nos. phase indicating lamps each backed up with MCB and
switch shall be provided for incomer. Busbar:- 100A, TPN Aluminium
a) 40A 10KA,'C' curve 4P MCB -04 Nos,
b) 10A-32A 10KA,'C' curve SP MCB - 18 Nos,
TOTAL CARRIED TO ELECTRICAL SUMMARY - 13,87,255.00 11,01,094.00
Sign of Contractor Page 29 of 52 NBCC
Digitally signed by ANUJ
Items Ref. (DSR- DSR (2022 ) DSR (2025 ) Non DSR
Sl No Description Unit Qty
2022) Rate in Rs. Amount in Rs. Amount in Rs. Amount in Rs.
9.0 UPS / INVERTER
Supplying, installation, Testing & Commissioning of of following
capacity at full load (Unity Power Factor) at operating temperature
0 to 40 deg C, Relative humidity 0 to 95%, Online double
conversion true sine wave Uninterrupted hot swappable (allow for
the replacement or addition of battery modules without shutting
down the entire system) modular Power Supply (UPS) system with
N+1 modules (N denotes total number of moduels requird for rated
capacity). The UPS shall include a Rectifier, inverter, battery bank
suitable for 30 minutes back up (Battery VAH capacity shall not be
less than 1600 VAH per KVA of UPS rating per Hour backup time)
on full load (Battery shall be VRLA, SMF in ABS Container) and
Static Bypass switch alongwith provision for manual bypass,
suitable isolation transformer for additional protection against
neutral faults etc. UPS shall have inbuilt phase sequence correction.
The UPS systems offered are to be of the latest technology with
Digital Control Microprocessor based for reliable operation using
Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier &
inverter (3 Level) with PWM (Pulse Width Modulation). The quality
of design, manufacturing and inspection process should confirm to
the relevant International standards such as IEC/EN/VDE. The
operating efficiency of the UPS systems shall be >96% while
operating on battery mode and delivering quality power to the
100% non-linear loads. Current total harmonic effect(ITHD) on the
input grid shall be < 5% at 50 %load. (The required LC (inductor (L)
and a capacitor (C)) filters shall be included in UPS cost), extreme
power factor kit to be included to limit the input power factor (PF)
to 0.99 and output power factor shall be unity (i.e. kw rating of the
UPS shall be kva rating x 1 ), however UPS shall be suitable to take
load at 0.7 laging to 0.7 leading power factor loads. UPS shall be
suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5
Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload
capacity of 120% for 10 mins, Sine wave output. Non condensing,
noise level less than 60db at 1 meter distance, protections: Input
Under voltage over voltage, abnormal out voltage, battery over
charging, output over current, short circuit protection, battery
deep discharge protection, 10KV surge. UPS must comply with low
voltage electromagnetic compatibility (EMC) achieved as per EN
6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency
Independent (VFI)-type UPS. Communication RS232/RS485/SNMP
port open protocol for BMS integration, all hardware & software
for iOT Communication as per approved by Engineering in charge.
Required battery racks and interconnecting copper conductor
cables of suitable size and connectors and all required accoseries
are inclusive of the cost). This system must provide a means for
logging and alarming of all monitored points plus email notification.
Forced air-cooling with integral inbuilt fans with redundancy (if one
fan fail UPS should be able to handle at least 80% of the load, Noise
Level 65 DB at 1 meter distance. The system shall be in compliance
IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display
Panel (minimum) (In-build 5 inch or more LC Display / LED ) to
display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage,
Frequency. c) Output: Voltage, frequency, Current.
9.1 5.2.2 (DSR- 2025) 20KVA (Each Power module shall be < 10 KVA) No. 1.00 3,41,772.00 3,41,772.00
TOTAL CARRIED TO ELECTRICAL SUMMARY - 3,41,772.00 -
Sign of Contractor Page 30 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT,
DSR (2022 ) DSR (2025 ) Non DSR Amount
Sl No DSR Ref No Description of Items Unit Qty Rate
Amount in Rs. Amount in Rs. in Rs.
1 POWER DISRIBUTION SYSTEM
Design, manufacture,of Type tested panel, supply inspection, instalation, handling, assembling,
affecting proper connections, testing and commissioning of 14 SWG CRCA sheet steel fabricated
cubical type Main L.T. Panel, floor mounting, dust & vermin proof, front operated construction,
enclosure class - IP 52, powder coated after proper treatment with 9 tank process with
top/bottom removable gland plates, as required, double compression type cable glands, earth
bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter
connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The Aluminium
Bus Bar shall be of suitable length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS
8623 . The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured
aluminium cable or Aluminium Bus Duct as required.
All incoming / bus coupler MCCB shall be microprocessor based with O/L & S/C and E/F
protection and all Outgoings MCCB's may be thermo-magnetic based O/L & S/C protection.
All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking arrangement, with trip
setting as per load requirement. All TP MCCB shall be with heavy duty solid isolable neutral link.
The breaking capacity specified for breakers is Ics value (service rating).
The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmeter,
selector switches, cast resin type CT's & PT's, etc. Separate CT's shall be provided for protective
and measuring system.
All Energy Analyser / TVM Shall have RS 485 Modbus RTU on board Communication protocol for
SCADA communication.
The fault withstanding capacity of panel & its control gear shall be min. 25-50 KA rms for 1 sec.
GA drawings shall be got approved from Owners / Architects / Consultants before
fabrication.The panel has to be specifically fabricated as per the space available at Stilt level.
1.1 MAIN PCC PANEL:-
2 nos 1000A,4P, 50kA, Electrically Operated, manually Drawout type ACB with Mircro- process
Based O/L,S/C & E/F Releases
The Contactor shall be electrically & Mechanically interlocked with both incoming & Bus
coupler's contactor in such a way that at any one time two supply should not get mixed up.
Metering for incomers
2 nos ACB Under Voltage Releases 415V, AC.
0-500 volt range voltmeter with selector switch (P.T. connected)
2 set of 3 CT's of ratio 1000/5A, Class 1.0 accuracy 15 VA burden for metering.
1 set of 3 CT's of ratio 1000/5A, Class 1.0 accuracy 15 VA burden for APFCR.
2 nos. Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of
Conzerve or equi.) with RS 485 communication port for communication / report generation.
Power factor meter.
Indications for incomers: 3 Nos. LED type phase indicating lamps, each lamp shall be with bakup
OUT GOINGS: All outgoing feeders shall be provided with one set of phase indication lamps and
trip indication lamps with protection fuses/MCB and ammeter with selector switch with suitable
ratio CT's of accuracy class 1.0
4 No. 250amps 4P MCCB 50kA outgoing feeder .
6 No. 200amps 4P MCCB 50kA outgoing feeder .
6 No. 160amps 4P MCCB 50kA outgoing feeder .
5 No. 100amps 4P MCCB 50kA outgoing feeder .
5 No. 80amps 4P MCCB 25kA outgoing feeder .
5 No. 63amps 4P MCCB 25kA outgoing feeder .
Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of
TPN 50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED
Indicating Lamp set along with required Instruments and accessories with
extended rotary handle and door interlocking arrangement. Current rating of
the Incomer in ampere shall be APFC Panel rating in KVAR x 1.4 x 1.5 or
Nearest higher standards rating.
(B) Instruments & Indications
i) 3-Phase current sensing APFC microprocessor relay/controller , advance
8/12 stages (8 stages for capacity below 100 KVAR and 12 stages 100 KVAR
& above) with Communication Ethernet/RS485/SNMP port open protocol for
BMS integration as per approved by Engineering in charge and having
display of Phase wise V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V , THD-I,
harmonics up to 31 level. 3 nos of dual core CT's accuracy class 1, 15VA at
incomer of PCC Panel for APFC relay.
ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in
iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA,
KVAR, THD-V & I, Frequency.
iv) Suitable rating control transformer shall be provided for control and
indication circuit.
Sign of Contractor Page 31 of 52 NBCC
Digitally signed by ANUJ
DSR (2022 ) DSR (2025 ) Non DSR Amount
Sl No DSR Ref No Description of Items Unit Qty Rate
Amount in Rs. Amount in Rs. in Rs.
v) All components like control transformer, meter, relay and indicating lamp
shall be protected by using suitable rating individual MCB's.
vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS 1100
V grade, PVC insulated multi stranded copper control wire.
1.3 Amp per Sq.mm, TPN, Electrolytic grade Aluminum bus bar of capacity
1.25 times of incomer rating as per CPWD specification.
(D) Outgoings (APFC Section)
Selection of the capacitors combinations shall be for continuous rating and
each capacitor bank shall have suitable capacity Heavy Duty ISI Marked
Capacitor, capacitor duty contactor, the capacitor shall be mounted on
channel with base of perforated M S Powder coated sheet, connections inter
connections etc. and other features as per CPWD Specifications and
relevant IS Code having following:
(i) Capacitor bank ratings & stages shall be as per the technical
specifications sheet of NIT.
(ii) Capacitor will be MPP self healing type with discharge resistor, pressure
release mechanism.
(iii) Since Capacitor Voltage is 525 Volts, thus higher KVAR has to be
considered to get rated output at 415 Volts.
(iv) 14% Detuned Reactor of class H insulation & 150% linearity in series with
(Note: Technical specifications sheet for selection of the capacitors
combinations shall be provided by the NIT Approving Authority with due
consideration of number of capacitors i.e. 1 KVAR, 2 KVAR, 3 KVAR, 5
KVAR, 10 KVAR.....for smooth correction).
1.3 FLOOR PANEL-1
Incomer:- 1 nos 200 AMP FP MCCB of 50 KA
The Contactor shall be electrically & Mechanically interlocked with both incoming & Bus
coupler's contactor in such a way that at any one time two supply should not get mixed up.
Metering for incomers
1 nos. Under voltage relay with timer.
0-500 volt range voltmeter with selector switch (P.T. connected)
1 set of 3 CT's of ratio 200/5A, Class 1.0 accuracy 15 VA burden for metering.
1 set of 3 CT's of ratio 200/5A, Class 1.0 accuracy 15 VA burden for Indications for incomers: 3
Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB.
OUT GOINGS: All outgoing feeders shall be provided with one set of phase indication lamps and
trip indication lamps with protection fuses/MCB and ammeter with selector switch with suitable
ratio CT's of accuracy class 1.0
8 No. 63amps 4P MCCB 10kA outgoing feeder .
8 No. 40amps 4P MCCB 10kA outgoing feeder .
NDSR 2 5 No. 40amps DP MCCB 10kA outgoing feeder . Set 4.00 1,85,000.00 7,40,000.00
5 No. 32amps DP MCCB 10kA outgoing feeder .
1.4 FLOOR PANEL-2
Incomer:- 1 nos 160 AMP FP MCCB of 50 KA
The Contactor shall be electrically & Mechanically interlocked with both incoming & Bus
coupler's contactor in such a way that at any one time two supply should not get mixed up.
Metering for incomers
1 nos. Under voltage relay with timer.
0-500 volt range voltmeter with selector switch (P.T. connected)
1 set of 3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for metering.
1 set of 3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for Indications for incomers: 3
Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB.
OUT GOINGS: All outgoing feeders shall be provided with one set of phase indication lamps and
trip indication lamps with protection fuses/MCB and ammeter with selector switch with suitable
ratio CT's of accuracy class 1.0
8 No. 63amps 4P MCCB 10kA outgoing feeder .
8 No. 40amps 4P MCCB 10kA outgoing feeder .
NDSR 3 5 No. 40amps DP MCCB 10kA outgoing feeder . Set 4.00 1,68,000.00 6,72,000.00
5 No. 32amps DP MCCB 10kA outgoing feeder .
1.5 COMMON AREA PANEL
Incomer:- 1 nos 100 AMP FP MCCB of 50 KA
The Contactor shall be electrically & Mechanically interlocked with both incoming & Bus
coupler's contactor in such a way that at any one time two supply should not get mixed up.
Metering for incomers
1 nos. Under voltage relay with timer.
0-500 volt range voltmeter with selector switch (P.T. connected)
1 set of 3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for metering.
1 set of 3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for Indications for incomers: 3
Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB.
OUT GOINGS: All outgoing feeders shall be provided with one set of phase indication lamps and
trip indication lamps with protection fuses/MCB and ammeter with selector switch with suitable
ratio CT's of accuracy class 1.0
4 No. 63amps 4P MCCB 10kA outgoing feeder .
4 No. 40amps 4P MCCB 10kA outgoing feeder .
NDSR 4 8 No. 40amps DP MCCB 10kA outgoing feeder . Set 1.00 1,45,000.00 1,45,000.00
8 No. 32amps DP MCCB 10kA outgoing feeder .
TOTAL CARRIED TO ELECTRICAL SUMMARY - 3,74,776.00 33,07,000.00
Sign of Contractor Page 32 of 52 NBCC
Digitally signed by ANUJ
DSR (2022 ) DSR (2025 ) Non DSR Amount
Sl No DSR Ref No Description of Items Unit Qty Rate
Amount in Rs. Amount in Rs. in Rs.
Supply Installation Testing And commissioning of DG Set complete with 1500 RPM
Diesel Engine of suitable BHP & AC Brush less SPDP Alternator mounted on a
common base Frame & coupled through a flexible coupling or close coupled.
Alternator: It shall be self-regulated, self-excited and confirms to IS: 13364/1992
or latest version with regulation of +5% from No load to full load, IP23, with
standard Alternator Protection (over voltage, over speed
& under voltage).
Diesel Engine: It shall have residential silencer, up to 10 M exhaust piping,
electronic / Mechanical governor, Manual & electric Start, Batteries, Fuel tank &
piping, control panel (16 G) with SPN(For 5 KVA)/TPN MCCB of required rating
(25/36/50 KA) with PLC based Engine controller supplied by OEM, Ammeter,
Voltmeter, Frequency Meter or Multi-function meter, Energy Meter & Hour Meter,
Engine instruments panel, AVM and Automatic Voltage Regulator. The diesel
engine shall be capable of providing 10% overload for 1 Hr for every 11 Hrs of
continuous running at full load. The DG set shall be supplied with initial filling of
fuel, lube oil, coolant oil as per OEM specifications and shall be tested at site.
Acoustic Enclosure: Weatherproof, powder coated Acoustic enclosure for DG set
for sound attenuation fabricated from 1.6 mm CRCA sheet steel (structure) with
side wall fabricated from 1.6 mm CRCA sheet and filled with foam as per CPCB
norms latest amendments & IS 8183. The doors are fabricated from 1.6 mm CRCA
sheet packed with acoustic material, floor of MS chequered plate 5.0 mm thick, all
doors/ opening are sealed with neoprene/ EPDN gaskets.
The DG Set shall be maintained for two years after commissioning by the supplier
including regular servicing, cost of consumables etc complete as specified by the
OEM along with warranty for two years.The enclosure has built in fuel tank,
residential silencer (isolated from main DG chamber) with protection and tripping
of DG set against temperature of more than 50 °C. All controls for operation of DG
set are from outside the enclosure with DG control panel having processor based
genset monitoring and control system MCCB/ACB Ammeter, voltmeter, PF meter,
frequency meter, KWH meter, Ind. Lamps etc. mounted inside enclosure, visible
and accessible from outside. The enclosure should be suitable for following
capacity DG sets and alternator. Noise level is less than 75 db (A) at a distance of 1
Mtrs as per CPCB-II norms, complete in all respect of following capacity:
2.1 4695 (DSR- 2025) Supply, installation, testing and commissioning of 500 kVA at 0.8 pf 415V 50Hz 3-Ø DG SET Nos 1.00 22,80,000.00 22,80,000.00
TOTAL CARRIED TO ELECTRICAL SUMMARY - 22,80,000.00 -
Supply, installation, testing and commissioning of 500KVA ,3 phase, 11/ 0.433 KV oil filled
Transformer copper wound with Dyn -II connection and neutral brought out for earthing. The
transformer shall be provided with (–) 5% and (+) 15% ON load tap changer on HT side including
RTCC Panel as per IS:1180 PART- 2-Level-2 or ECBC+BUILDING-2017 . HT side cable termination
box shall be suitable for 11 KV, 3 C x 240 mm2 XLPE cable and LT side terminal box shall be
suitable for terminating of 3.5 core 240 AMP Al XLPE Cable. The transformer shall be supplied
with all standard fitting viz dial type winding and oil temperature indicator, buchholz relay with
trip and alarm contacts, thermistors for Alarm and Trip, winding temperature relay unit
with Alarm and trip, lifting lugs, earthing studs, drain oil point de- hydration oil outlet & inlet, oil
conservator and marshlling box, etc. complete in all respect as required as per specification.
TOTAL CARRIED TO ELECTRICAL SUMMARY - 11,79,071.00 -
Sign of Contractor Page 33 of 52 NBCC
Digitally signed by ANUJ
DSR (2022 ) DSR (2025 ) Non DSR Amount
Sl No DSR Ref No Description of Items Unit Qty Rate
Amount in Rs. Amount in Rs. in Rs.
Supplying, installation, testing & Commissioning of One Panel HT VCB
4.10 Outdoor Board. VCB panel shall comprise of following items. ( One
number Near Transformer)
1 number 630 Amps 18.4 KA, I/C & O/G VCB Outdoor Panel circuit breaker horizontally
insulated horizontal draw out, electrical motor operated, spring charged with facility of
manual closing.
'1 no. 11KV / 1.732/110V/1.732 drawout. PT suitable for resistively earthed system with
100VA burden having accuracy class as 1.0.
'3 number combined 160/5+5 current transformers. Cast resin class 1.0 accuracy 15 VA
minimum burden for metering class & 5PI0 of 15VA burden for protection. The CT shall
have shorting links.
'Multifunction meter having P.F meter, KW meter, KWHr meter, ammeter with RS 485
port and communication link.
'One local / remote switch for operation.
'One emergency OFF push button outside
'Spring charge status.
'1 set indicating light for breaker ON/OFF & indicating light for D.C circuit healthy,
indicating light for three phases.
'One no. numerical microprocessor based separate three phase over current (IDMT +
Instantaneous element) with separate instantaneous earth fault relay, trip circuit
supervision relay, one no. two elements transformer auxiliary VAA 22 relay, 1 no. separate
standby earth fault relay and master trip relay. ON /OFF /TRIP indications.
'Auto / Manual switch. In manual mode it shall have local TNC switch for operation
'Separate indication for each electrical fault.
'1 number 30 VDC shunt trip coil and 30V DC closing coil.
'1 number circuit for remote tripping & closing of the breaker through a potential free
'1 Set of HRC fuses, control wiring, protection wiring, and other item required for the
desired operation of the unit selector switch to indicate the currents.
'8 Annunciator window for all electrical and transformer fault.
'Suitable Built in power Pack one set
'All interconnected control wiring.
Supply and fixing of 11 KV ,400 A 3 phase central post rotating double break type
AB switch(isolator) as per IS 9921) without earth blade, gang operated, Horizontal
type, operating mechanism with GI spring loaded reverse loop type fixed contact,
solid HD electrolytic copper tubular moving contact with silver/Nickel plated at
end points,9 Nos post insulators of 12 KV (IS 2594 and IS 5350) ,Hot Dip
galvanizing hardware, GI pipe, Nuts and bolts etc., complete.,
Providing transformer plinth 1.2 x 1.2 x 1.5 mtr in size with necessary excavation
in ground at the bottom with 150mm thick 1:2:4 cement concrete raft at the
4.3 NDSR 7 bottom and top and 225mm thick wall constructed in stone masonry and Nos 1.00 13,747.42 13,747.42
remaking hallow portion shall be filled with stone chips duly plastered 20mm thick
outsides including watering etc., complete.
Supply and fixing of 100 A 11 KV Horn Gap fuse set as per IS 9385 on existing DP
4.4 NDSR 8 structure with 6 no of 24 KV /22 KV post Insulators (IS 5350, Hot dipped Hardware, Nos 1.00 6,850.00 6,850.00
fuse wire of required size etc., complete
Supplying and erection of three piece nonlinear resistor type lightning arrestor
suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a
nominal discharge current rating of 5 KA and complete with galvanised clamping Nos 1.00 2,628.00 2,628.00
arrangement, G.l. bolts, nuts, washers etc. as required.
Supplying and erection of bow stay set complete (galvanised) with 19/20 mm dia X
1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm, thimble,
stay clamps, turn buckle ( 20 mm X 60 cm ), 7/ 4.00 mm dia G.l. stay wire and
4.6 12.5 strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded Nos 1.00 5,969.00 5,969.00
stone aggregate 40 mm nominal size ) foundation including excavation and
refilling and also with 0.6 m long brace of size 50 mm X 50 mm X 6 mm angle iron
with 50 mm dia pulley fixed at one end of the brace as required.
Supplying and erection of 11 KV pin insulator complete with large steel head G.l.
4.7 13.1 pin, nuts, washers etc. as required. Nos 1.00 312.00 312.00
Supplying and erection of 100 mm X 110 mm shackle insulator with G. I. Bolt, nuts
4.8 12.7 and straps etc. as required . Nos 1.00 207.00 207.00
Supply and Transportation of Over Head 55 Sqmm AAA Conductor as per IS 398
Supply Transportation and unloading the RS joint of 2 nos 9.0 mtr long 175mm x85
5.0 NDSR 10 mm size at site in good condition for H.T / L.T. Line support including cost and Nos 1.00 33,788.05 33,788.05
conveyance of all materials and labour charges. Ect.
Labour Charges for fixing of RS joint of 2 nos 9.0 mtr long including earth work
4.10 NDSR 11 exevation and cement concreat 1:2:4 with necessary 8 J bolts ects. Nos 1.00 14,424.33 14,424.33
Fabrication of 100 x 50 mm MS channel for supporting AB switch fuse carriers, LAS
4.11 NDSR 12 units, insulators, horigentally operated air break switch, lightening arester etc. Nos 1.00 24,108.56 24,108.56
Providing and fixing Zero Gueafe copper wire on surface or in recess for loop
earthing along with existing surface/ recessed conduit/submain wiring/cable as RMT 12.00 439.40 5,272.80
Providing and fixing 32 mm X 6 mm copper strip on surface or in recess for
4.13 NDSR 14 connections etc. as required. RMT 20.00 1,578.00 31,560.00
Sign of Contractor Page 34 of 52 NBCC
Digitally signed by ANUJ
DSR (2022 ) DSR (2025 ) Non DSR Amount
Sl No DSR Ref No Description of Items Unit Qty Rate
Amount in Rs. Amount in Rs. in Rs.
Supply, Unloading, storage & Laying of following sizes of 3-core, 11kV, E, HT, XLPE
cable in ground & Cable try the prices shall include excavation of soil and refilling,
4.14 providing sand layer below the cables, providing half cut hume pipe over and
above the cable for necessary mechanical protection before final refilling of soil
and making good surface as required.
Supply and erection of 1.1 KV Grade PVC insulated cables cable terminations with
4.15 Al. / Cu. lugs, double compression type cable glands, PVC insulation tapes and all
other accessories as required.
a NDSR 16 11KV 3C - 150 Sq.mm XLPE, Al.(E) Indoor NOS 3 8,500.00 25,500.00
b NDSR 17 11KV 3C - 150 Sq.mm XLPE, Al.(E) Outdoor NOS 1 9,800.00 9,800.00
4.16 NDSR 18 Supply and laying of 3.5 C x 240 sq.mm (XLPE), aluminium armoured LT cable. Rmt 200 1,650.00 3,30,000.00
4.17 NDSR 19 End Termination ( Double compressor Glands) No. 12 2,850.00 34,200.00
4.18 NDSR 20 TRANSFORMER YARD FENCING :
Fencing the Transformer yard, 2.5Meter Height vide materials listed under :
The rates quoted shall include necessary excavation, PCC for ISMC Supports,
coping complete.
Frame size : 2.5 M x 1.5 M
M.S.Angle : 50 x 6 mm
Chain Link : 8 SWG GI.
Supporting ISMC : 75 x 40 mm
4.18.1 Paint : 2 Coats of Red oxide & 2 coats of enamel paint RMT 35 2,250.00 78,750.00
Note: Extension of the exsisting fencing.
Gate for HT & METERING Yard (Single leaf)
Frame size : 1.0 x 2.5 M
GI Pipe : 40 mm with Chain link fencing
4.18.2 Paint : 2 Coats of Red oxide & 2 coats of enamel paint NOS 1 14,500.00 14,500.00
4.18.3 Supply and Spreading of 40 mm metal in outdoor H.T.yard - 100 mm - thick layer Sq.M 40 850.00 34,000.00
TOTAL CARRIED TO ELECTRICAL SUMMARY 9,116.00 13,41,246.51
Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and
5.1 5.2 providing masonry enclosure with cover plate having locking arrangement and No. 1.00 6,855.00 6,855.00
watering pipe etc. with charcoal/ coke and salt as required. (HT PANEL)
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt
as required.(TRANSFOMER & DG SET)
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt
as required.(TRANSFOMER & DG SET)
Providing & fixing of 40mm x 6mm GI strip on surface or recess for earth
5.4 NDSR 21 connection as required. RMT 20.00 3,500.00 70,000.00
Providing & fixing of 75mm x 6mm GI strip on surface or recess for earth
connection as required.
TOTAL CARRIED TO ELECTRICAL SUMMARY 1,07,039.00 98,000.00
6 MISCELLANEOUS ITEMS
Supply and laying of 11kV Grade Rubber Mats of size 1000mm x2000mm bearing 4
6.2 NDSR 24 Supply and fixing of CO2 Fire Extinguishers 4.5Kg cap NOS 4 8,300.00 33,200.00
Supply and fixing of Fire Buckets with stand (with two nos of Buckets in each)
painted in Post Office red
6.4 NDSR 26 Supply and Fixing of Laminated First Aid Charts in Telugu, Hindi & English NOS 4 2,600.00 10,400.00
Supply & Installation of Danger Boards-Stove enamelled (150mm X 150mm) with
6.5 NDSR 27 warnings in Telugu, Hindi & English. NOS 4 1,100.00 4,400.00
Supply & Installation of First-Aid Box, as per relevant IS along with all necessary 2
6.7 NDSR 29 Supply and Fixing of Laminated SLD-A1size NOS 2 4,200.00 8,400.00
TOTAL CARRIED TO ELECTRICAL SUMMARY - 99,900.00
Sign of Contractor Page 35 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
1 CCTV (IP VIDEO SURVEILLANCE) SYSTEM
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
surface/recess including cutting the wall and making good the same in case of recessed
conduit as required.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable as per EIA in the existing surface/
recessed Steel/PVC Conduit as required.
1/3" , 650 TVL, 2.8-12mm vari-focal lens, 42pcs IR LED, fixed iris,IR:40M Vandalproof,IP66, with
2MP Full-color Guard+ Network IR Dome Camera 1/2.7” 2Megapixel PS CMOS Image Sensor
1.6 NDSR 2 Max. 2MP(1920 x 1080)@25/30fps H.265+/ H.264+ dual-stream encoding DWDR, Day/Night Nos 30.00 8,500.00 2,55,000.00
(ICR), 3D-DNR, ROI, AWB, AGC, BLC, HLC 3.6mm fixed lens (2.8mm optional) IR Range of 15
2MP Full-color Guard+ Network IR Bullet Camera 1/2.8” 2Megapixel PS CMOS Image Sensor
Max. 2MP(1920 x 1080)@25/30fps Smart H.265+ and Smart H.264+ dual-stream encoding
1.7 NDSR 3 DWDR, Day/Night (ICR), 3D-DNR, ROI, AWB, AGC, BLC, HLC 3.6mm fixed lens (2.8mm optional) Nos 60.00 12,850.00 7,71,000.00
IR Range of 20 Mtrs., IP67,
32 Ch. H.265 4K Network Video RecorderUp to 32 channel IP camera input H.265/H.264 dual
codec decoding Up to 8Mp resolution preview and playback Max 200Mbps incoming
1.8 NDSR 4 bandwidth Support 4 SATA HDDs up to 24TB, 2 USB(1 USB3.0) HDMI / VGA simultaneous video Nos 3.00 82,500.00 2,47,500.00
output Support Multi-brand network cameras
Supply, Installation, Testing & Commissioning of of Access Switch 24 Port POE+ Access
Switches with switching capacity of 128 Gbps, forwarding performance 95 Mpps, having 24 x
10/100/1000BASE-T PoE- plus(RJ45) with minimum PoE budget of 370W and 4 x 10G SFP+
uplink ports, should have support for 9 switch Stacking with bandwidth of minimum 120 Gbps. 1.00
Should support min 2GB internal DRAM, 2GB internal Flash memory, 32K MAC address, 4k
Multicast Routes, Should have static Routing from day 1 and upgradable to support OSPF and
VRRP with 1 year support.
JetStream 16-Port Gigabit Easy Smart PoE+ Switch with 2 SFP Slots 16 10/100/1000Mbps RJ45
PoE+ Ports Switch with 2 SFP Slots PoE power budget is up to 192W, making it ideal for small
to medium business surveillance systems Port Priority is able to guarantee the quality of
sensitive application like video monitor Intelligent power management can protect the switch
from overload QoS is for smooth internet-surfing experience and IGMP Snooping is capable of
optimizing traffic for IPTV.
2.10 NDSR 7 Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk. Nos 3.00 14,731.00 44,193.00
Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per
2.11 NDSR 8 ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to Nos 90.00 250.00 22,500.00
jack panel connectivity.
Supply, Installation, Testing & Commissioning of CAT 6 UTP Universal (both tool & toolless)
information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition,
ISO/IEC TR 11801-9901-2014, ROHS Compliant.
2.12 NDSR 9 The I/O should have minimu 750 mating cycle and 200 insertion cycle and UL approved,for Nos 90.00 550.00 49,500.00
Data, Voice, & Wi-Fi at user end.
2.13 NDSR 10 Supply and Instalation of PVC BOX Nos 90.00 450.00 40,500.00
Supply , Installation, Testing and Comissioning of Wall mounted Communication rack in two
sections viz rear wall mount Section and hinged front section with glass doors, swing handles
,lock , Top and Bottom Cable entries,Supports for mounting rack on wall , Cable managers, Fan
tray with 2 x 230 Volt fans, Equipment mounting hardware, wire managers , power supply box
for supplying power to hubs, fans etc along with earth continuity kit, Mcb, indicator, moulded
power supply cable, Blank panels , sliding shelves etc.
a NDSR 11 6 U wall Floor Mounted Nos 4.00 8,500.00 34,000.00
b NDSR 12 12 U wall mounted Nos 1.00 12,850.00 12,850.00
2.15 NDSR 13 Steel Stands for the Dome cameras NOS 10.00 1,550.00 15,500.00
2.16 NDSR 14 6 Meter Stainless Steel Galvanized Camera Poles NOS 11.00 7,500.00 82,500.00
2.18 NDSR 16 Supply , Installation, of 4K UHD, 55" LED Disply unit Nos 1.00 1,38,042.00 1,38,042.00
TOTAL CARRIED TO CCTV SUMMARY 81,000.00 22,76,852.00
2 NETWORKING SYSTEMS
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
surface/recess including cutting the wall and making good the same in case of recessed
conduit as required.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable as per EIA in the existing surface/
recessed Steel/PVC Conduit as required.
Supply installation testing and commisioning of 1no of Cat6 Tooless builtin crimping
mechanism Information Outlet with Dust Cover Exceed ANSI/TIA-568-C.2 and ISO/IEC 11801
2.5 NDSR 17 standards with 1module face plate for Category 6 component performance & Compatible to Each 120.00 470.00 56,400.00
T568A,T568B wiring pattern and UL-940V0 Rated Plastic &RoHS Compliant
Makes: Systimax /AMP/ Panduit/ Siemond/ Molex/Legrand
2.6 NDSR 18 Supply and instalation of Managed WiFi Access Point (Ceiling-Mounted) Each 15.00 29,500.00 4,42,500.00
Sign of Contractor Page 36 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
Supply , Installation, Testing and Comissioning of Wall mounted Communication rack in two
sections viz rear wall mount Section and hinged front section with glass doors, swing handles
,lock , Top and Bottom Cable entries,Supports for mounting rack on wall , Cable managers, Fan
tray with 2 x 230 Volt fans, Equipment mounting hardware, wire managers , power supply box
for supplying power to hubs, fans etc along with earth continuity kit, Mcb, indicator, moulded
power supply cable, Blank panels , sliding shelves etc.
2.8 NDSR 20 12 U wall mounted Each 1.00 12,850.00 12,850.00
2.9 NDSR 21 8 U wall mounted Each 4.00 8,500.00 34,000.00
2.10 NDSR 22 Supply & Fixing of 24 port Gigabit Managed Switch Each 8.00 25,850.00 2,06,800.00
2.11 NDSR 23 24 port cat-6 patch panel Angular Type. Each 8.00 8,500.00 68,000.00
Supply installation testing and commisioning of 4 pair 23AWG Cat6 UTP ,flexible ,double ended
2.12 patch cords along with 2 nos of RJ 45 connectors with strain relief boots Compatible to
T568A,T568Bspecifications including making connections to information outlets
2.13 NDSR 26 Supply installation of 2 Moduler Base box metal. Each 126.00 150.00 18,900.00
2.14 NDSR 27 Supply installation of Dual Face Plate Each 126.00 185.00 23,310.00
TOTAL CARRIED TO NETWORKING SYSTEMS 5,65,400.00 9,24,500.00
3 TELEPHONE SYSTEMS
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
surface/recess including cutting the wall and making good the same in case of recessed
conduit as required.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable as per EIA in the existing surface/
recessed Steel/PVC Conduit as required.
Supply and erection of approved make RJ11 Telephone socket with modular box and front
plate, as directed by the department including cost and conveyance of a l l materials and
labour charges etc complete
Supply and laying of 50 pair telephone wire including labour charges for laying in existing PVC
3.6 NDSR 29 conduit pipr and giving connection etc complete RMts 60 200.00 12,000.00
Supply and erection of 50 pair telephone distribution box with back mount frame, krone
connector, powder coated metal body with lock and key arrangement including cost and
conveyance of all materials and labour charges etc complete
Supplying and laying 20 pair cable telephone cable. The Rate should include for providing
3.8 NDSR 31 necessary identification with cable marking ferrules. RMts 40 120.00 4,800.00
Supply, Installation, testing and Commissioning of IP Based digtal Telephone (EPABX) system ----
-complied with following specifications:
> IP @ Core, PCM/TDM, Non-blocking,
> Must Support PRI, E1, Analog Junctions
> Must Support PC Console,
> Must support Mobile SIP (Android and Ios)
> Must support Voice Mail
> Must support Card based GSM
3.9 NDSR 32 > Inbuilt 8 Channel Auto Attendant Each 1 1,43,990.00 1,43,990.00
> Inbuilt Call Details Software with search engine software
> 4 Analog Trunks
> 1 ISDN PRI Module
> 6 Digital Extensions
> 64 Analog Extensions
> 1 Digital Key Phone with minimum 16 Keys (Must work only on 2 wires)
> Expandable to 64 Analog Extensions or more
Makes: As per list of recommended brands.
TOTAL CARRIED TO TELEPHONE SYSTEMS 3,21,250.00 3,20,040.00
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
4.1 surface/recess including cutting the wall and making good the same in case of recessed
conduit as required.
Supply and laying of RG 11U tinned copper co-axial cable with polythene insulation and overall
PVC sheathed in 25/32mm dia FRLS LMS PVC conduit from MATV room to various Tap off and
from Tap off to various Splitter points in LV Shaft(including end terminal). (Rate to be quoted
4.2 NDSR 33 for FRLS PVC conduit on ceiling/concealed in concrete slab/wall complete with GI pull wire, RMts 240 58.00 13,920.00
conduit fittings, conduit accessories like saddles, spacers, bends, couplings, collars etc.,
junction / pull / inspection boxes, conduit supports)
Supply and laying of RG 6U tinned copper co-axial cable with polythene insulation and overall
4.3 NDSR 34 PVC sheathed in 25 dia FRLS LMS PVC conduit from various Floor Splitter to TV outlet RMts 720 35.00 25,200.00
(including end terminal)
Supply and installation of 4-way splitters in die cast Aluminum Junction Box with required
necessary accessories.
Sign of Contractor Page 37 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
Supply and installation of 6-way splitters in die cast Aluminum Junction Box with required
4.5 NDSR 36 necessary accessories. Nos 1 650.00 650.00
Supply and installation of 2-way splitters in die cast Aluminum Junction Box with required
4.6 NDSR 37 necessary accessories. Nos 1 450.00 450.00
Supply and installation of 6/8-port tap-off units in die cast Aluminum junction box with
4.7 NDSR 38 necessary 'alternators as specified and shown on drgs.complete. Nos 1 1,150.00 1,150.00
Supply and installation of 4-port tap-off units in die cast Aluminum junction box with
4.8 NDSR 39 necessary 'alternators as specified and shown on drgs.complete. Nos 1 1,000.00 1,000.00
Supply & installation of 2-port tap-off units in die cast Aluminum junction box with necessary
4.9 NDSR 40 alternators as specified & shown on drawing. Nos 1 850.00 850.00
Supply & installation of MATV Setup Box Complete with all accessories, Cabling,Channel card
4.10 NDSR 41 minimum etc. (Contractor to quote base on qty and scope of work will be decied after pre-bid Nos 20 8,500.00 1,70,000.00
Supply & installation of Coaxial TV Outlet socket as per approved make or as per approved by
the Architect / Client.
TOTAL CARRIED TO TELEPHONE SYSTEMS 1,72,750.00 2,19,070.00
5 Acess Control System
Supply and erection of Matrix make Optical Fingerprint and EM Proximity Card based Reader
Time-Attendance IP65 Rating 50,000 Events and 9,600 Fingerprint Template Storage Built-In
Power over Ethernet (PoE), RS-485 and Ethernet Interface Tri Color LED and Buzzer 12VDC
Power Supply through Adaptor or Battery Backup
Supply and erection of Matrix Make Fingerprint and EM Prox Card based Reader Optical
Fingerprint and EM Proximity Card based Reader RS-232/RS-485 Interface IP65 Rating Tamper
Detection Tri Color LED and Buzzer 12VDC Power Supply through Adaptor or
Battery Backup Compatible with any COSEC Door Controllers (Except COSEC DOOR FOT)
Supply and erection of Base Platform & Time and Attendence Software for COSEC CENTRA
Base Platform with 100 Users along with 100 Users Access Licence , 5 Default Users for each
TAM, ACM, ESS, CMM, JPC, FVM, CWM and 1 Default VMM User along with Dongle and 10
5.4 NDSR 46 Supply and erection of 600LBS EM Lock for Door Each 12 3,750.00 45,000.00
Supply and erection of 802.11ac Long Range Access Point The UniFi AC LR AP features the
5.5 NDSR 47 latest Wi-Fi 802.11ac technology in a refined industrial design and is ideal for long-range Each 15 36,750.00 5,51,250.00
deployment of high ‑performance wireless networks.
Supply and erection of Hybrid Cloud Device Management Featuring Hybrid Cloud technology,
5.6 NDSR 48 the UniFi® Cloud Key securely runs a local instance of the UniFi Controller software and Each 1 20,000.00 20,000.00
features cloud Single Sign-On for remote access.
TOTAL CARRIED TO Acess Control System - 10,07,000.00
SITC of Interactive display with OPS having, Screen Size: 110 inches (diagonal), Resolution:
3840 x 2160 (4K UHD), Aspect Ratio: 16:9, Brightness: 350cd/m2 (Min) & 500cd/m2(Max),
Contrast Ratio: 1200:1, Viewing Angle: 178° horizontal / 178° vertical, Display Color: 1.07
billion colors (10-bit), Response Time: 8ms, Life Time: Up to 50,000 hours, and Operating
System: Android 12.0, CPU: Octa-core ARM Cortex-A55 @1.5GHz, GPU: Quad-core ARM Mali-
G52 @600MHz, RAM/ROM: 4GB DDR + 32GB EMMC / 8GB DDR + 64GB EMMC, I/O Interface:
HDMI IN x 2, USB-B x1, VGA + Audio x 1, USB-A 2.0 x 1, USB-A 3.0 x 1, RJ45 IN x 1, TF Card Slot
1, RS232 x 1, COAX x 1, Line OUT x 1, Touch Technology: High precision IR touch, Multi-User
Support: Supports up to 20 points of touch, Network Support: 1 Gigabit networks for Android
6.2 NDSR 50 Mounting system for above display Each 1 15,600.00 15,600.00
SITC of Professional Display having Screen Size: 65 inches (diagonal), Resolution: 3840 x 2160
(4K UHD), Aspect Ratio: 16:9, Brightness: Up to 450 nits, Contrast Ratio: 1200:1, Viewing Angle:
178° horizontal / 178° vertical, Display Color: 1.07 billion colors (10-bit), Response Time: 8ms,
6.3 NDSR 51 Life Time: Up to 50,000 hours, Connectivity: HDMI IN x 2, VGA, USB-A 2.0 x 1, USB-A 3.0 x 1, Each 1 80,600.00 80,600.00
RJ45 IN x 1, Audio: Built-in speakers with 10W output per channel, Power Consumption:
Typical 150W, Maximum 200W, Mounting Options: VESA mount compatible.
6.4 NDSR 52 Mounting system for above display Each 1 6,500.00 6,500.00
SITC of Screen Size: 21.5” Inch or Higher, should be LED backlight, Resolution: Full HD (1920 x
1080), Touch Technology: 10-point projected capacitive touch, Display Type: SuperClear IPS-
type technology, Brightness: 250 cd/m² or more, Contrast Ratio: 1000:1, Viewing Angles: Wide
6.5 NDSR 53 viewing angles for multi-user environments, Refresh Rate: 60Hz, Color Gamut: 72% NTSC Each 1 25,350.00 25,350.00
(CIE1931), Operating System: Android (Windows optional), Connectivity: HDMI, VGA, USB
ports. Monitor should have 2x5W speakers.
SITC of Connects any of 8 HDMI sources to any of to 8 HDMI displays, Multiple means for
system configuration including front-panel pushbuttons,RS-232 control, and Ethernet
connections for web-based GUI or Telnet, Seamless Switch™ , real-time switching, and stable
signal transmissions, Scaler, selects optimum EDID settings for smooth power-up, high-quality
display, and use of the best resolution across different screens, preventsimage tearing by
6.6 NDSR 54 synchronizing the scaler output frame rate to the input signal frame rate, Superior video Each 1 10,66,000.00 10,66,000.00
quality – HDTV resolution of 480p, 720p, 1080i and 1080p (1920 x 1080), HDMI (3D, Deep
color); HDCP 1.4 compatible, Consumer Electronics Control (CEC) support, Local HDMI output
–allows multiple preview of 8 video sources, Audio-enabled; HDMI audio can be extracted to
stereo audio, Supports Dolby True HD and DTS HD Master audio, ESD protection for HDMI,
Rack-mountable (2U design).
Sign of Contractor Page 38 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
SITC of Wireless presenter having Resolution: Supports 4K UHD (3840 x 2160) at 30Hz.,
Connectivity: 802.11 a/g/n/ac wireless transmission protocol, Operating System: Compatible
with Windows 10 and higher, macOS 11 and higher, Android 9 and higher, iOS 12 and higher,
Video Outputs: HDMI 1.4b, USB-C DisplayPort 1.2 (only Gen2), Audio Output: HDMI, USB,
Buttons: 1 or 2 ClickShare Buttons for easy content sharing, Touchback, Annotation, and
Blackboarding: Interactive features for engaging presentations, Maximum Sources
Simultaneously on Screen: 2 sources, Frequency Band: 2.4 GHz and 5 GHz, Connections:
Ethernet LAN 1Gbit, USB-C 2.0, USB-A 2.0 (Gen2: USB-C 3.0, USB-A 3.0), Temperature Range:
Operating: 0°C to +40°C, Storage: -20°C to +60°C, Certifications: FCC/CE.
SITC of Extends HDMI signals to one local and two remote displays up to 100 m over a single
(4:4:4), Max. Data Rate 10.2 Gbps (3.4 Gbps per Lane), RS-232 control, Connector: 1 x Terminal
Block, 3 pole, Baud Rate: 19200, Data Bits:8, Stop Bits:1, no parity and flow control, Power 1 x
DC Jack (Black) with locking or 1 x RJ-45 (Power over HDBaseT, PoH), 1 x DC Jack (Black) with
locking, Operating Temperature 0 - 50°C.
SITC of Super Telephoto professional 4K PTZ AI tracking camera with 30x Optical zoom. High
quality 1/1.8 Inch large CMOS sensor and pixel density is 8.42 megapixels, Whose Field of View
is Horizontal: 59.2° & Vertical: 34.6. Equiped with 3D noise reduction and backlight
compensation technology for dynamic exposure correction & clarity in various lighting
6.9 NDSR 57 environments, even low light. Tally ligh for active streaming indication, also supports Each 3 2,01,500.00 6,04,500.00
simultaneous transmissions of audio & video through NDI Port. PTZ Camera supports multiple
output interface - HDMI 2.0, 3G-SDI, USB & LAN. Video compression supports
h.264/h.265/MJPEG
SITC of Ideal Box For Making Computer Presentations on BoardRoom/Conferance Room,
Tables, Manual Desktop Connection Box, Sliding Top Cover for easy access to connectors, 2 x
6.10 NDSR 58 Un-switched AC power Sockets 110v-240v 50/60HZ,10A Outlet, 2 USB Charging Points to Each 4 47,450.00 1,89,800.00
charge IPad/Laptop/Mobile Phone etc, 6 Pass-through holes for putting Audio-Video Cables.
SITC of column Speaker with transducer system features 16 units, each with a diameter of 2.75
inches. It has a nominal impedance of 8 ohms and a minimum impedance of 5.8 ohms at 3650
Hz. The system's RMS power is rated at 200W (40V rms), with a program power of 400W and a
peak power of 800W (80V peak). Its sensitivity measures 94 dB SPL at 2.83V/1m, and it can
reach a peak SPL of 123 dB. The frequency range spans from 130Hz to 23kHz (-10dB) and from
150Hz to 20kHz (-6dB). High frequencies are managed at the top, opposite to the logo end. It is
recommended to use a Butterworth 24dB/Oct high pass filter at 100Hz. The horizontal
coverage at - 6dB is 140°, while the vertical coverage at -6dB is 20°. The system has an IP65
rating and the enclosure is made of aluminum.
Supply of 2-way passive loudspeaker with a power rating of 70 W at 8 Ohms for low
impedance. For high impedance, it offers 32 W at 312 Ohms, 16 Wat 625 Ohms, 8 W at 1.25
kOhms, and 4 W at 2.5 kOhms for L100V; and 16 W at 625 Ohms, 8 W at 1.25 kOhms, 4 W at
2.5 kOhms, and 2 W at 5 kOhms for L70V. The speaker has a nominal impedance of 8 Ohms
and features an 8-inch woofer along with a 1-inch tweeter. It has a sensitivity of 93 dB at
6.12 NDSR 60 1W/1m and a maximum SPL of 111 dB. The coverage angle is 120º x 90º, and it operates Each 4 15,340.00 61,360.00
within a frequency range of 75 Hz to 20 kHz. The connections are via Euroblock, and the
enclosure is made of polypropylene with an aluminum grill. It includes wall brackets for
mounting and is available in white (RAL 9003) and black (RAL 9004). The speaker is also IP54
rated for protection against dust and water.
SITC of Class D. Switched power supply 2 Channel Amplifier with Watt per channel at 8 Ohm is
500W and watt per channel at 4 ohm is 850 watt and Watt at Bridge mode at 8 Ohm is 1700W.
Frequency Range of Amplifier is 20Hz - 20KHz with threshold noise is less than 0.15% with
Signal to noise ration is greater than 100dB. Damping Factor of amplifier will be 500 or better
with Revenue 38.2dB.Input Impedance of Amp will be 20 KOhm (balanced) and 10 KOhm
6.13 NDSR 61 (unbalanced) with Input Sensitivity 0.775V / 1V / 32dB.Connectors of Power Amp will be Each 1 72,345.00 72,345.00
Powercon for power with XLR3 for input and output Signal. Protections for Amp will be Soft
start, VHF, DC, Overload, Clip, Limitation, Short circuit, Over temperature, Progressive volume.
Fans Airflow from front to rear for cooling effect . AC Power Supply will be 100-240V, 50/60Hz
with Consumption 800W
SITC of Digital signal processor with min. 08AEC enabled Mic/Line inputs, 08 Line outputs or
better , Input channel processing should include Pre amplifier, Signal generator, Expander,
Compressor, 10 band Parametric EQ or better, Output Channel processing should include 31
band Graphic equilizer, Delay, Crossover, limiter or better, Other features should include
Automatic mixing console, Ducker, Feedback elimination, Noise elimination, echo elimination
6.14 NDSR 62 or better, Should have built-in Bi directional USB for Software based VC as well as for playing Each 1 1,39,100.00 1,39,100.00
digital audio, Should have built in Camera tracking Module, 8 Port Freely configurable GPIO or
better with Analog/Digital dynamic range of 114dB or better, Sampling rate of 48Khz or better,
Frequency response of 20Hz – 20Khz or better, per channel phantom power module or better.
Should be configurable thru software.
Sign of Contractor Page 39 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
SITC of flush Mount Chairman Unit with a discreet recessed enclosure design, ideal for
seamless integration. Crafted with precision, it boasts a high-quality Copper Zinc alloy die-cast
body ensuring durability and aesthetic appeal. The unit features a detachable Screw Type
Microphone for flexible usage.Equipped with a backlit Speak & Override button for clear
visibility in any environment. Its microphone employs a Cardioid Condenser Polar pattern,
delivering optimal sound capture. The frequency response spans from 50Hz to 20KHz,
6.15 NDSR 63 capturing a wide range of audio frequencies. Sensitivity is rated at -20dBV (+/-3dB) with a Each 1 25,350.00 25,350.00
maximum input sound pressure level of 110dB (THD < 5%, f=1KHz), ensuring clear and crisp
audio transmission.With a remarkable signal-to-noise ratio exceeding 100dBA (THD<1%,
f=1Khz), it minimizes background noise for enhanced clarity. Distortion is kept below 0.1%,
maintaining audio fidelity. Powered by a 24V DC supply from the controller, it consumes a
mere 0.72W of power. The unit interface utilizes an RJ45 network input, facilitating seamless
connectivity. Experience superior communication with this advanced Chairman Unit, designed
for exceptional performance and discretion.Gooseneck Microphone 16"
SITC of flush Mount Delegate Unit, featuring a discreet recessed enclosure design for seamless
integration. Crafted with a high-quality Copper Zinc alloy die-cast body, it ensures both
durability and an elegant appearance. The unit comes equipped with a detachable Screw Type
Gooseneck Microphone for flexible usage.Its Backlit Speak & button enhances visibility in
various environments. The microphone utilizes a Cardioid Condenser Polar pattern, capturing
clear and focused audio. With a frequency response ranging from 50Hz to 20KHz, it covers a
broad spectrum of sound.Sensitivity is rated at -20dBV (+/-3dB), ensuring accurate audio
capture. The unit can handle a maximum input sound pressure level of 110dB (THD < 5%,
6.16 NDSR 64 f=1KHz), maintaining clarity even at high volumes. A remarkable signal-to-noise ratio exceeding Each 11 25,350.00 2,78,850.00
100dBA (THD<1%, f=1Khz) minimizes background noise for pristine communication. Distortion
is kept below 0.1%, preserving audio fidelity. Powered by a 24V DC supply from the controller,
it consumes a mere 0.72W of power. The unit interface features an RJ45 network input for
seamless connectivity. Experience superior communication with this advanced Delegate Unit,
combining performance with discreet design. Gooseneck Microphone 16"
SITC of Conference Controller System, Should have Digital in nature with Dante Audio output
and with 4 or more Kinds of Conference Modes Including FIFO Mode, Request Mode,
Automatic Mode, Voice activation mode, the central controller should able to Select the No. of
speakers and Active 2/3/4 Mics simultaneously, Should support 110 Number of microphones
supported via additonal power supply unit, supports camera Tracking thru RS-232 & RS-422
Communication Protocols or more, Should have supports 4 or more Video inputs and 1 output
6.17 NDSR 65 port on SDI and HD-SDI video format or better, Should able to connect and control up to 4 Each 1 1,24,215.00 1,24,215.00
cameras simultaneously with in built auto switching between cameras as per microphones
connected to them. The Controller should Compatible with any PTZ camera having Visca, Pelco
D, and Pelco P Control mode protocols. It should have Dante digital output along with Analog
XLR and Phono output complete with standard accessories required.
SITC of Dual Channel Wireless Handheld Microphone system with Built in AFS(Automatic
Frequency Selection) technology,Should have UHF operating mode with Frequency range of
522 -930Mhz or better, Should have operating bandwidth 134 MHz or better, Anti Interference
technology ensures Noiselock Squelch effectively blocks Stray RF or better, Microphone
6.18 NDSR 66 Frequency Response of 45Hz to 18KHz or better, Should have Signal to noise ratio less then Each 1 51,870.00 51,870.00
104dB or better, RF output Power of 10/40mW or better, Should have maximum 24 set can be
used simultaneously by using multiple frequency bands in one venue, Should have die cast
metal body, Microphone element Dynamic or better complete with standard accessories
required as per tender.
SITC of High performance processor embedded with quad-core CPU and 2 GB memory for
designing and controlling complex projects, Dual, isolated LAN for secured communication
among IT devices, Supports various interface connections for hardware-software integration
and mobile device control, DC outputs for power supply connections, USB port for easy project
upload, LCD display shows the option for configuration and information display, IR learning
function for adding IR device drivers, Web Viewer – integrated with 3rd-party systems or any
web-based console for easier room equipment management, Supports native KNX IP for
building management systems, Telnet, TCP, UDP, HTTP, HTTPS, ONVIF, and PJLink compliant,
6.19 NDSR 67 Supports Pronto formatted IR codes – IR command codes can be entered in Hex format, Each 1 3,70,500.00 3,70,500.00
Supports Modbus protocol – enables integration with Modbus devices, including TCP, RTU and
its checksum data, Supports Telnet CLI (command-line interface) mode for third-party system
integration, Supports centralized control and management by ATEN Unizon™, Supports project
file backup, Web GUI for easy system configuration, Supports SSH communication for data
monitoring, LED indication of connection and hardware status, 2 free licenses for mobile
SITC of network switch having Ports: 16 10/100/1000 Mbps Ethernet ports, 2 SFP ports, Power
over Ethernet (PoE): Supports IEEE 802.3af/at with a total power budget of 150W, PoE Ports:
6.20 NDSR 68 Ports 1-8 support PoE devices up to 250 meters distance, Flow Control: 802.3x flow control on Each 1 45,500.00 45,500.00
each port minimizes dropped packets, Lightning Protection: 6kV protection, Operating
Temperature: 0°C to 40°C (32°F to 104°F).
6.21 NDSR 69 SITC of 10.1 in. Tabletop Touch Screen, Black Smooth. for controlling all the automation Each 1 3,14,600.00 3,14,600.00
SITC of Ultra Flexible Premium High Speed HDMI Cable 1m, Max. Video Resolution:
4096x2160@60Hz (4:4:4), Operating Temperature 80℃, HDMI Ethernet Channel functionality:
additional dedicated data channel supports networking, HDMI (3D, Deep Color, 4K); HDCP 2.2
compliant, RoHS compliant, Bend Radius 90°
SITC of Ultra Flexible Premium High Speed HDMI Cable 10m, Max. Video Resolution:
4096x2160@60Hz (4:4:4), Operating Temperature 80℃, HDMI Ethernet Channel functionality:
6.23 NDSR 71 additional dedicated data channel supports networking, HDMI (3D, Deep Color, 4K); HDCP 2.2 Each 3 9,750.00 29,250.00
compliant, RoHS compliant, Bend Radius 91°
Sign of Contractor Page 40 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable as per EIA in the existing surface/
recessed Steel/PVC Conduit as required.
Supply, Installation, Testing and Commissioning of 13 AWG Speaker Cable (80/0.20 mm) x 2
6.26 NDSR 72 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform RMT 100 111.00 11,100.00
Type PVC Sheath
Supply, Installation, Testing and Commissioning of 18 AWG (24/0.20mm) x 2 core ATC copper
conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof
Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged
6.28 NDSR 74 RJ45, XLR, EP Jack, BNC connector LOT 1 11,570.00 11,570.00
SITC of All AV Equipment’s to be housed inside a 27 U Equipment Rack, Lockable front glass
door, cooling facility, internal wiring, front glass door, heat dissipation fans, and power
distribution units, 19” 27 U Floor MountAV EquipmentRack.
Sign of Contractor Page 41 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
SCHEDULE OF QUANTITY FOR ELV SERVICES WORK
DSR QTY. DSR 2022 Non DSR
Sl No Description Unit
Ref No (Court) Rate Amount in Rs. Amount in Rs.
SITC of Professional Display having Screen Size: 65 inches (diagonal), Resolution: 3840 x 2160
(4K UHD), Aspect Ratio: 16:9, Brightness: Up to 450 nits, Contrast Ratio: 1200:1, Viewing Angle:
178° horizontal / 178° vertical, Display Color: 1.07 billion colors (10-bit), Response Time: 8ms,
6.30 NDSR 76 Life Time: Up to 50,000 hours, Connectivity: HDMI IN x 2, VGA, USB-A 2.0 x 1, USB-A 3.0 x 1, Each 2 65,000.00 1,30,000.00
RJ45 IN x 1, Audio: Built-in speakers with 10W output per channel, Power Consumption:
Typical 150W, Maximum 200W, Mounting Options: VESA mount compatible.
6.31 NDSR 77 Mounting system for above display Each 2 8,000.00 16,000.00
SITC of Wireless presenter having Resolution: Supports 4K UHD (3840 x 2160) at 30Hz.,
Connectivity: 802.11 a/g/n/ac wireless transmission protocol, Operating System: Compatible
with Windows 10 and higher, macOS 11 and higher, Android 9 and higher, iOS 12 and higher,
Outputs: HDMI 1.4b, USB-C DisplayPort 1.2 (only Gen2), Audio Output: HDMI, USB, Buttons: 1
6.32 NDSR 78 or 2 ClickShare Buttons for easy content sharing, Touchback, Annotation, and Blackboarding: Each 2 1,48,000.00 2,96,000.00
Interactive features for engaging presentations, Maximum Sources Simultaneously on Screen:
2 sources, Frequency Band: 2.4 GHz and 5 GHz, Connections: Ethernet LAN 1Gbit, USB-C 2.0,
USB-A 2.0 (Gen2: USB-C 3.0, USB-A 3.0), Temperature Range: Operating: 0°C to +40°C, Storage:
-20°C to +60°C, Certifications:
SITC of 78 Deg FoV / 12x Optical & 16x Digital Zoom / 4K@30fps / Connectors - USB3.0 (Type
6.33 NDSR 79 C) / HDMI / RJ45 / NDI (Optional) / Auto Framing, Presenter Tracking, BIS, CE, FCC, RoHS, and Each 2 66,000.00 1,32,000.00
CB Certification.
SITC of Ideal Box For Making Computer Presentations on BoardRoom/ Conferance Room,
Tables, Manual Desktop Connection Box, Sliding Top Cover for easy access to connectors, 2 x
6.34 NDSR 80 Un-switched AC power Sockets 110v-240v 50/60HZ,10A Outlet, 2 USB Charging Points to Each 2 36,000.00 72,000.00
charge IPad/Laptop/Mobile Phone etc, 6 Pass-through holes for putting Audio- Video Cables.
SITC of Ultra Flexible Premium High Speed HDMI Cable 1m, Max. Video Resolution:
4096x2160@60Hz (4:4:4), Operating Temperature 80℃, HDMI Ethernet Channel functionality:
SITC dedicated
of Ultra Flexible data channel
Premium Highsupports networking,
Speed HDMI HDMI
Cable 10m, (3D,Video
Max. DeepResolution:
Color, 4K); HDCP 2.2
4096x2160@60Hz (4:4:4), Operating Temperature 80℃, HDMI Ethernet Channel functionality:
6.36 NDSR 82 additional dedicated data channel supports networking, HDMI (3D, Deep Color, 4K); HDCP 2.2 Each 2 5,500.00 11,000.00
compliant, RoHS compliant, Bend Radius 92°
6.37 NDSR 83 SITC of USB A to A cable 10m Each 2 6,500.00 13,000.00
TOTAL CARRIED TO AV SYSTEM 5,400.00 66,20,615.00
7 PUBLIC ADDRESSING SYSTEM
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
7.1 surface/recess including cutting the wall and making good the same in case of recessed
conduit as required.
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the
7.2 17.5.3 existing surface / recessed steel conduit of following pairs, cores and size including connections
and interconnections etc. as required.
a 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Rmt 2000 54.00 1,08,000.00
Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB,
7.3 17.3.1 MP3 player (including 6 zone button paging station) with seamless integration facility with Nos 1 1,26,411.00 1,26,411.00
main fire alarm panel for voice evacuation complete as required.
7.4 17.3.2 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as Nos 180 965.00 1,73,700.00
Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers
7.5 17.3.3 complete as required. Nos 180 1,793.00 3,22,740.00
Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with
microphone assembly complete as required.
Supply,installation, testing and commissioningg of 400 W PA Installation Rack mounted
Booster amplifier
Supply,installation, testing and commissioningg of 400 W PA Installation Rack mounted
7.8 NDSR 85 Mixed amplifier Nos 3 70,000.00 2,10,000.00
7.9 NDSR 86 Supply,installation, testing and commissioningg of wired mike . Nos 24 2,850.00 68,400.00
Supply,installation, testing and commissioning of 8U Rack 550 x 500 suitable for PA System
7.10 NDSR 87 with 6A Power distribution Unit 5- socket, 90CFM cooling fan, 1 x shelf, hardware with front Nos 3 15,000.00 45,000.00
metal glass door.
TOTAL CARRIED TO Acess Control System 10,57,857.00 5,40,435.00
Sign of Contractor Page 42 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT,
FIRE FIGHTING WORK
DSR 2022 Non DSR Amount
Sl.No. DSR No Description of Item Unit Quantity RATE
Amount in Rs. (Rs)
i) FIRE FIGHTING SYSTEM
Supplying and fixing single headed Internal / External hydrant valve with
instantaneous Gunmetal coupling of 63 mm dia with cast iron wheel ISI marked
conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain
Supplying and fixing of hose cabinet of size 750mm X 600mm x 250mm made of No
16 gauge SWG CRCA sheet with 6mm thick glazed glass door including necessary
locking arrangement suitable to accommodate 2 Nos 15 mtr long Hose pipe, 1 No
branch pipe, mounted on wall OR raised brick platform and duly painted with Post
office red externally and white internally with synthetic enamel paint complete in all
respect, for external hydrant as required.
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and
3 18.16 female Gun metal / SS couplings duly bound with GI wire, rivets etc. conforming to
IS 636 (type-A) as required :
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal
4 18.18 internal diameter size Gun metal / SS nozzle conforming to IS 903 suitable for Nos. 16 2,416.00 38,656.00
instantaneous connection to interconnect hose pipe coupling as required :
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post
office red, conforming to IS 884 complete with the following as required.
a) 40m long 20 mm nominal internal dia water hose thermoplastic (Textile
reinforced) type -2 as per IS: 12585
b) 20 mm nominal internal dia gun metal globe valve & nozzle.
c) Drum and brackets for fixing the equipmets on wall.
d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and
Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe
conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers,
6 18.8 nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable Nos.
clamp/support frame and painting with two or more coats of synthetic enamel paint
of required shade complete as required :
a 18.8.1 25 mm dia (wall thickness 6.3 mm) RM 1500 608.00 9,12,000.00
h 18.8.8 150 mm dia (wall thickness 6.3 mm) RM 10 2375.00 23,750.00
Supplying and fixing of fire brigade connection of cast iron body with gun metal
7 18.19 male instantaneous inlet couplings complete with cap and chain as reqd. for suitable
dia MS pipe connection conforming to IS 904 as required :
Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm
in height with air release valve on top and flanged connection to riser, drain
8 18.20 arrangement with 25 mm dia gun metal wheel valve with required accessories, Set 5 18,244.00 91,220.00
pressure gauge and paintingwith synthetic enamel paint of approved shade as
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type
9 18.21 sprinklers of rating 68 degree centigrade Pendent / Side wall with required Nos. 480 522.00 2,50,560.00
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as
Providing & fixing flow switch in following sizes M.S. pipe including connection etc as
Sign of Contractor Page 43 of 52 NBCC
Digitally signed by ANUJ
DSR 2022 Non DSR Amount
Sl.No. DSR No Description of Item Unit Quantity RATE
Amount in Rs. (Rs)
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed)
of stainless steel complete with 15 NPT on reducer thread with maximum working
pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm
12 18.25 NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer,
nipple, 2 side brackets, center bracket, stockbar of following sizes complete as
Supplying, installation, testing and commissioning of Electric driven Main Fire Pump
suitable for automatic operation and consisting of following, complete in all
respects, as required :
The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2
pressure at the highest/farthest point with specific flow of 2280 lpm at 70 m head.
a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body &
bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.
b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM,
suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection
for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to
c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts
etc. as required.
d) Suitable cement concrete foundation duly plastered with anti vibration pads.
Supplying, installation, testing and commissioning of diesel engine driven main fire
pump suitable for automatic operation and consisting of following, complete in all
respects, as required : (Diesel Driven Pump)
The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2
pressure at the highest/ farthest point with specific flow of 2280 lpm at 70 m head.
a) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze
impeller with stainless steel shaft, mechanical seal conforming to IS 1520.
b) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to
14 18.2 relevant IS standard complete with auto starting mechanism, 12 /24 volts electric Nos. 1 6,12,065.00 6,12,065.00
starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump
house duly insulated 50 mm thick glass wool with 1.0 mm thick aluminium sheet
cladding, residential silencer, instruments and protection as per standard
specification, stop solenoid for auto stop in the event of fault with audio indications,
painted with post office red colour etc. as required.
c) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts
etc. as required.
d) Suitable cement concrete foundation duly plastered and with anti vibration pads.
Supplying, installation, testing and commissioning of electric driven pressurisation
pump suitable for automatic operation and consisting of following, complete in all
respects, as required : (Jockey Pump)
a) Horizontal type, multistage, centrifugal pump of cast iron body and bronze
impeller with stainless steel shaft, mechanical seal and flow of 180 lpm at 70 m
head.conforming to IS : 1520.
b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415
volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal
foot mounted type with Class-'F' insulation, conforming to IS : 325.
c) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts
etc. as required.
d) Suitable cement concrete foundation duly plastered and with anti vibration pads.
Sign of Contractor Page 44 of 52 NBCC
Digitally signed by ANUJ
DSR 2022 Non DSR Amount
Sl.No. DSR No Description of Item Unit Quantity RATE
Amount in Rs. (Rs)
Fabrication, supply, Insallation testing & commissioning of Electrical control panel of
cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet,
compartmentalised with hinged lockable doors, dust and vermin proof, powder
coated of approved shade after 7 tank treatment process, cable alley, inter-
connection with suitable size copper conductor cable/solid copper strip, having
switchgears and accessories, mountings and internal wiring, earth terminals,
numbering etc. complete in all respect, suitable for main fire pump, pressurisation
pump & diesel pump set complete as per CPWD specification with following in
coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with
enclosure protection class IP 42 as required :
250A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector
switch Digital Ammeter (0-250 A) with selector swtich & CTs etc.
LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper
16 18.5.1 OUTGOING
( Note : All outgoing feeders for pumps should have digital Ammeter with selector
switches, and LED type ON, OFF, trip indicating lamps)
125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable
for 60 HP pump with overload protection, current sensing type single phase
preventor complete with all acceessories and internal wiring required for automatic
operation, selector switch for local/remote, auto/manual/OFF operation.
63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta
starter with overload protection, current sensing type single phase preventor
complete with all acceessories and internal wiring required for automatic operation,
selector switch for local/remote, auto/manual/OFF operation.
DIESEL ENGINE CONTROL
Control for diesel engine comprising - Automatic/ Manual selctor switch & 3
attempts starting device, timers and relays as required, push buttons, start/stop in
Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on
Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30
V DC volt meter, and 0- 20 A DC Ammeter
All standard relays and accessories for automatic operation of diesel engine. Nos. 1 2,45,730.00 2,45,730.00
System Controller
Designing, Supply, Installation, Testing and commissioning of system controller to
control operation of main electric fire pump, diesel pump, Pressurization pump,
Terrace pump in sequence as per specification of main electric fire pump, diesel
pump, Pressurization consisting of relays, timers. Sensors, annunciation window for
fault indication, complete as per specification.
Supplying, installation, testing and commissioning of 100mm dia stainless steel Y-
17 18.15.2 strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm Nos. 3 6,664.00 19,992.00
dia holes with stainless steel flange.
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with
18 18.11 bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as required :
Providing, installation, testing and commissioning of 100mm dia non-return valve of
19 18.14 following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, Nos. 4 11,050.00 44,200.00
washers etc.as required :
20 NDSR 2 Supply, installation, testing and commissioning of 25mm dia Ball valve. Nos. 10 857.80 8,578.00
21 NDSR 3 Supply, installation, testing and commissioning of 25 / 20mm dia Air Release valve. Nos. 2 1,627.00 3,254.00
Supply, installation testing and commissioning of under ground pipe anti corrosive
protection as per IS - 10221 embedded heavy class MS pipes and fittings (running
below trenches) by applying pyp kote primer (@ 100 gm/sqm) thereafter wrapping
4 mm thick protection coating by thermo fusion process and overlaping of joints
shall be done as per manufacturer’s specification. Wrapping shall be confirm to IS
10221 including
a).All pipes barried below ground will be protected against soil corrosion by
wrapping and coating material as per IS: 10221-2008.
Sign of Contractor Page 45 of 52 NBCC
Digitally signed by ANUJ
DSR 2022 Non DSR Amount
Sl.No. DSR No Description of Item Unit Quantity RATE
Amount in Rs. (Rs)
ii) FIRE ALARM SYSTEM
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with
1 17.5.2 annealed copper conductor having XLPE insulation, steel wire armouring & ERLS Nos. 1600 173.00 2,76,800.00
outer sheath complete as required.
Supplying, installation, testing & commissioning of heat detector operating at
2 17.1.1 542C/572C with rate of rise cum fixed temperature (dual thermistor) type with Nos. 20 1071.00 21,420.00
mounting base complete with all connection etc. as required.
Supplying, installation, testing & commissioning of smoke detector with builtin LED
and mounting base complete with all connections etc. as required.
Supplying, installation, testing & commissioning of manual call boxes of MS
4 17.1.3 construction in surface/recess with stainless steel chain & hammer assembly Nos. 24 474.00 11,376.00
complete with glass and push button etc. as required.
Supplying, installation, testing & commissioning response indicator on
5 17.1.5 surface/recess MS box having two LEDs metallic cover complete with all connections Nos. 1 196.00 196.00
etc. as required.
Supplying, installation, testing & commissioning fire alarm sounder with facility to
make announcement, mounted in M.S. box (16 SWG) with hinged cover plate &
suitable for operation with amplifier i/c line matching transformer etc. complete as
Supplying, installation, testing & commissioning sector panel suitable for following
zones, complete with visual indications for short circuit fault, open circuit fault, fire
condition and all other standard facilities as per IS:2189 with mimic diagram for all
area/zone covered, complete with all connections, interconnections as required.
Supply and fixing of Co2 type Fire Extinguishers 4.5 Kg capacity confirming to IS 2878
made from ISI marked steam less cylinder confirming to IS:7285 & CE certified and
fitted with ISI marked controlled valve confirming to IS:3224, high pressure 1 Mtr
8 NDSR 5 discharge hose & horn complete with initial gas charged with carrying handle with Nos 4 16,279.89 65,119.56
wheels and wall mounting bracket. Squeeze lever discharge, used un-used indicator,
epoxy coated paint (Red) with 93% gloss with 2 years warranty including
transportation, all taxes and all labour charges etc complete
Supply and fixing of ABC stored pressure squeeze grip type fire extinguishers, 9 kg
capacity, IS:15683 : 2006, filled with ABC Mono Ammonium Phosphate base powder-
90 complete with discharge hose and wall mounting bracket, 2mm Mild Steel, EPDM
Rubbers, Pressure Gauge, which work effectively on all class of fires (A, B, C &
Electrical fires) with 5 years warranty Including transportation, all taxes and all
labour charges etc complete
Supply and fixing of Escape signage boards in Rigid Photo luminescent based glow in
Dark rigid sheet with high intensity luminous properties with specification.
TOTAL CARRIED TO SUMMARY 70,22,959.00 4,26,403.68
Sign of Contractor Page 46 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA
DSR QTY. DSR 2022 DSR 2025 Non DSR
Sl No Description Unit RATE
Ref No (Court) Amount in Amount in Rs. Amount in Rs.
HI - WALL SPLIT SYSTEMS
Supply , Installation, Testing and Commissioning of Air Cooled Hi
Wall split type Air conditioners complete with Indoor unit(IDU),
Out door unit (ODU), surface / concealed copper Refrigerant
piping with insulation (closed cell elastomeric nitrile rubber
tubular pipe section) upto 3 Mtr (IDU to ODU), copper power
cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-
407 Green Refrigerant, wireless Remote control, suitable for
working between 180-260V with low & high voltage cutoff and
50 hz ,1 phase AC supply capable of performing cooling,
8.2 (DSR dehumidification, air circulation of following capacity with Scroll
2025) / rotary compressor. The system shall be able to deliver 100% of
the rated capacity upto 42 Degree Celsius. Min 5 year Original
Equipment Manufacturer (OEM) warranty both compressor and
Printed Circuit Board (PCB). Must comply : Electrical cable IS 694
or IS 9968 temperature sensing control IS /International Electro
technical Commission (IEC) 60730, hermetic compressor IS
10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS
12615. Complete as per CPWD specification and IS : 1391 Part II
2023. The system shall be able to operate up to 50 0C (out door
ambient temperature).
8.2.2 1.0 TR with 5 Star BEE Rating Each 0 39,196.00 -
8.2.3 1.5 TR with 5 Star BEE Rating Each 6 42,055.00 2,52,330.00
8.2.4 2.0 TR with 5 Star BEE Rating Each 1 55,440.00 55,440.00
OUTDOOR UNIT VRF
Supply, Installation, Testing & Commissioning of Modular type
Variable Refrigerant Flow/Variable Refrigerant Volume air cooled
Outdoor units suitable for cooling/heating having 100%
hermetically sealed inverter type twin Rotary/Scroll
Compressor(s),minimum two compressors (with individual
separate PCB) for above 14HP modules, microprocessor based
Controller, top discharge type condensing unit(s), with R-410-A
Refrigerant or equivalent, vibration Isolators with suitable
foundation etc. complete a required. To have better efficiency
condenser fan shall be capable to operate at different speed with
respect to load. The unit shall deliver the rated capacity and in
confirmation as per IS 18728:2024 and CPWD Specifications and
work even at 50°C ambient temperature without tripping. The
2 system shall be able to deliver 100% of the rated capacity upto
39 Degree Celcius.The unit shall be suitable to work on 400V +/-
50Hz AC power supply and BMS compatible. The unit shall be
filled with first charge of the refrigerant and ready for use as
required. The condenser should be coated with a hydrophilic film
to prevent water accumulation on the surface of the heat
exchanger, enhance water dispersion, and reduce the risk of
degradation, thereby improving overall performance and
durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of
the unit shall be as per Energy Conservation and Sustainable
Building Code (ECSBC) 2024 as below and complete as per CPWD
specification, connections, inter connections etc. as required.
(For capacity <40 kWr ISEER 6.4, Capacity > 40 and <70 ISEER 6.5,
2.1 7.2.2 Capacity
10 HP to >1270HPISEER 6.6 for ECSBC+ Building) HP 10 21,422.00 2,14,220.00
Sign of Contractor Page 47 of 52 NBCC
Digitally signed by ANUJ
DSR QTY. DSR 2022 DSR 2025 Non DSR
Sl No Description Unit RATE
Ref No (Court) Amount in Amount in Rs. Amount in Rs.
INDOOR UNIT VRF
Supply, Installation, Testing and Commissioning of following
minimum capacity High wall type Indoor unit equipped with and
comfort washable synthetic media pre-filter, fan section with low
noise fan/dynamically balanced blower, multispeed motor, coil
section with DX copper coil, electronic expansion valve, outer
cabinet, cord less remote control, drain pan, necessary
accessories etc., suitable for operation on 230 V ± 10%, 50 Hz,
3 single phase AC supply, complete as required. The Indoor units
must shut down upon receiving a singal from the BMS
System/Fire Singnals. The system shall be capable to adjust air
flow as per room requirement automatically. The cooling
capacity of indoor unit will be at air inlet conditions of 27 Degree
C DB and 19 Degree C WB temperature. (Make will be same as of
Supply, Installation, Testing and Commissioning of following
minimum capacity 4 way Cassette Type Indoor ceiling mounted
unit equipped with synthetic washable media pre-filter, fan
section with low noise fan / dynamically balanced blower,
multispeed motor, coil section with DX Copper coil, electronic
expansion valve, outer cabinet, drain pump, grill, necessary
supports, vibration Isolation, Corded remote control etc.,
4 suitable for operation on single phase 230 V ± 10%, 50Hz AC
supply, complete, as required. The Indoor units must shut down
upon receiving a singal from the BMS System/Fire Signals. The
system shall be capable to adjust air flow as per room
requirement in auto mode. The cooling capacity of indoor unit
will be at air inlet conditions of 27 Degree C DB and 19 Degree C
WB temperature. (Make will be same as of Outdoor)
Supply, Installation, Testing and Commissioning of following
minimum capacity Single way wall/corner VRV/VRF Cassette
Type Indoor ceiling mounted unit equipped with synthetic
washable media pre-filter, fan section with low noise
fan/dynamically balanced blower, multispeed motor, coil section
with DX Copper coil, electronic expansion valve, outer cabinet,
drain pump, grill, necessary supports, vibration Isolation, Corded
5 remote control etc., suitable for operation on single phase 230 V
± 10%, 50Hz AC supply, complete, as required. The Indoor units
must shut down upon receiving a singal from the BMS
System/Fire Signals. The system shall be capable to adjust air
flow as per room requirement automatically. The cooling
capacity of indoor unit will be at air inlet conditions of 27 Degree
C DB and 19 Degree C WB temperature. (Make will be same as of
Sign of Contractor Page 48 of 52 NBCC
Digitally signed by ANUJ
DSR QTY. DSR 2022 DSR 2025 Non DSR
Sl No Description Unit RATE
Ref No (Court) Amount in Amount in Rs. Amount in Rs.
Supply, Installation, Testing and Commissioning of following
minimum capacity and external static pressure VRF/VRV ceiling
mounted high ductable type Indoor unit equipped with washable
synthetic media pre-filter, fan section with low noise
fan/dynamically balanced blower, multispeed motor, coil section
with DX copper coil, electronic expansion valve, corded remote
7.12 (DSR control, outer cabinet, vibration Isolators, drain pan, drain pump,
2025) other necessary supports etc., suitable for operation on single
phase AC supply 230 V ± 10%, 50 Hz complete as required. The
Indoor units must shut down upon receiving a singal from the
BMS System/Fire Signals. The cooling capacity of indoor unit will
be at air inlet conditions of 27 Degree C DB and 19 Degree C WB
temperature. (Make will be same as of Outdoor)
Supply, Installation, Testing and Commissioning of Y/T/Multi
7 7.13 Joints. Joints shall be of same Original Equipment Manufacturer
(OEM) make as of ODUs and IDUs
7.2 7.13.2 Outdoor Multi Joint Each 14 8,098.00 1,13,372.00
COPPER REFRIGERANT PIPING
Supply, Installation, testing and commissioning including
vaccumiazation and Nitrogen testing of following nominal sizes
of soft/hard drawn copper refrigerant piping for VRV/VRF
system, complete with fittings, with suitable adjustable ring type
8 hanger supports, jointing/brazing including accessories, insulated
with XPLE Class-O tubular insulation/with Class-O closed cell
elastometric nitrile rubber tubular sleeves sections of 19 mm
thick insulation as given below for Suction and Liquid lines, all
accessories as per specifications etc. as required :
8.1 7.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm RMT 375 256 96000
8.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm RMT 300 346 103800
8.3 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm RMT 275 487 133925
8.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm RMT 250 615 153750
8.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm RMT 220 739 162580
8.6 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm RMT 175 904 158200
8.7 7.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm RMT 150 1068 160200
8.8 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm RMT 125 1157 144625
8.9 7.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm RMT 100 1222 122200
8.10 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm RMT 85 1286 109310
8.11 7.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm RMT 75 1322 99150
8.12 7.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm RMT 60 1368 82080
Supply, installation, testing and commissioning of Gl volume Sqm
16.13 (DSR control duct damper complete with neoprene rubber gaskets,
2022) nuts, bolts, screws linkages, flanges etc, as per specifications.
16.15 (DSR Supplying & fixing of powder coated extruded aluminium Supply Sqm
2022) Air Grills with aluminium volume control dampers as per
Supplying & fixing of powder coated extruded aluminium Return Sqm
11 Air Grills with louvers but without volume control dampers 12 5910.00 70920
complete as required.
Supplying, fixing testing commissioning of supply air diffusers of Sqm
12 powder coated aluminium with aluminium volume control 72 12184.00 877248
dampers with anti smudge ring & removable core.
Supplying, fixing testing commissioning of Return air diffusers of Sqm
16.18 (DSR powder coated aluminium without volume control dampers with
2022) anti smudge ring & removable core.
Supplying, Fixing, testing and commissioning of fire dampers in
supply air duct/main branch and return air path as and where
required of required sizes i/c control wiring, the damper shall be
16.20.1 (DSR motorized and spring return so as to close the damper in the
14 event of power failure automatically and open the same in case
of power being restored. The spring return action shall be inbuilt
mechanism and not externally mounted. The damper shall also
be closed in the event of fire signal complete as required and as
per specifications.
a Fire damper Sqm 12 10659.00 127908
Sign of Contractor Page 49 of 52 NBCC
Digitally signed by ANUJ
DSR QTY. DSR 2022 DSR 2025 Non DSR
Sl No Description Unit RATE
Ref No (Court) Amount in Amount in Rs. Amount in Rs.
Supplying and fixing of following thickness duly laminated
aluminum foil of mat finish closed cell Nitrile rubber existing duct
16.23.1 (DSR after applying suitable adhesive for Nitrile rubber. The joints shall
15 be sealed with 50 mm wide and 3 mm thick self adhesive nitrile
rubber tape insulation complete as per specifications and as
required, above. Valves should have pressure rating of 25 Bar
Supply, installation, and testing of UPVC Drain Piping with 6mm
Nitrile Rubber class "O" Insulation covered with interwoven glass
16 cloth protection. Necessary pipe fittings (including enlarger,
bends, T-Joints etc) has to be considered to connect the UPVC
drain pipe to floor trap
Supply, installation, testing& commissioning of GSS Ducting with
required angle flanges & installation materials such as heavy
duty supports by anchor fasteners etc as required asper IS 655
/SMACNA Standards. Makes: As per list of recommended brands.
Incomer:- 1 nos 250 AMP FP MCCB of 50 KA
The Contactor shall be electrically & Mechanically interlocked with both
incoming & Bus coupler's contactor in such a way that at any one time two
supply should not get mixed up.
Metering for incomers
1 nos. Under voltage relay with timer.
0-500 volt range voltmeter with selector switch (P.T. connected)
1 set of 3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for
1 set of 3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for
Indications for incomers: 3 Nos. LED type phase indicating lamps, each lamp
shall be with bakup
OUT GOINGS: HRC fuse/MCB.
All outgoing feeders shall be provided with one set of phase
indication lamps and trip indication lamps with protection fuses/MCB and
ammeter with selector switch with suitable ratio CT's of accuracy class 1.0
8 No. 63amps 4P MCCB + RCCB 300mA outgoing feeder .
a NDSR 3 12 No. 40amps 4P MCCB + RCCB 300mA outgoing feeder . Set 2.00 2,40,000.00 4,80,000.00
8 No. 32amps 4P MCCB + RCCB 300mA outgoing feeder
TOTAL CARRIED TO SUMMARY 26,55,830.00 1,05,25,532.00 5,68,200.00
Sign of Contractor Page 50 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING
XI ADDITIONAL DISTRICT COURT AT GUDIVADA, KRISHNA DISTRICT, A.P".
GENERAL NOTES :
All items of work under this Contract shall be executed strictly to fulfill the requirements laid
1 down in the specifications, which shall include type of equipment, material, methods of
installation, type of controls, approved shop drawings and the relevant standards.
The rate for each item of work in the Schedule of Quantities shall, unless expressly stated
2 otherwise, shall also include the following:
a. All fixing materials, accessories, appliances, tools, plants, equipment, transport, labour and
incidentals required in preparation of and in the full and entire execution, testing,
commissioning and completion of the work called for in the item as per Specifications and
b. Wastage on materials and labour.
c. Loading, transporting, unloading, handling / double handling, hoisting to all levels, setting,
fitting and fixing in position, protecting, disposal of debris and all other labour necessary in
and for the full and entire execution and to fully complete the job in accordance with the
contract documents, good practice and recognized principles.
d. Liabilities, obligations and risks arising out of Conditions of Contract.
e. All requirements of specifications, whether such requirements are mentioned in the item or
not. The specifications and drawings where available, are to be read as complimentary to
and part of the Schedule of Quantities and any work called for in one shall be taken as
f. In the event of conflict between schedule of quantities and other documents including the
specifications, the most stringent shall apply and the interpretation of the consultants shall be
final and binding.
3 The unit rate for each equipment or materials shall be including Excise duty, Octori, Packing
& forwarding charges, freight up to site, transit insurance, loading & unloading, storage,
CST/VAT, Custom duty, Port clearance, any other statuary levies, installation, testing &
4 The extension for (total) amounts against each item shall be based on the quantities
indicated in this Schedule.
5 The quantities given in this schedule are provisional, the Owner reserves the right to
increase or decrease the quantities or to totally omit any items of work and the Contractor
shall not be entitled to claim any extras or damages on these grounds. These variations shall
be permitted until such time Contractors shop drawings are approved.
6 This schedule shall be fully priced and the extensions and totals duly checked. The rates for
all items shall be filled in INK.
7 No alteration whatsoever is to be made to the text or quantities of this Schedule unless such
alteration is authorized in writing by the Consultants. Any such alterations, notes or additions
shall unless authorized in writing be disregarded when tender documents are considered.
8 In the event of an error occurring in the amount column of the Schedule, as a result of wrong
extension of the unit rate and quantity, the unit rate quoted by the tenderer shall be regarded
as firm and the extensions shall be amended on the basis of the rates.
9 Any error in totaling in the amount column and in carrying forwarded totals shall be corrected.
Any error, in description or in quantity, or omission of items from this schedule shall not
vitiate this contract but shall be corrected and deemed to be a variation required by the
10 Consultants.
Obtaining of lift license and Handing over to client shall be the sole responsibility of
Sl. No. Items Ref. Description Unit Qty Rate in Rs.
Amount in Rs. Amount in Rs.
Design, manufactures, supply,installation, sting,commissioning, approvals / laisoning (All
local / state/ central statutory bodies) and handing over in satisfactory working conditions of
elevators as per specification.
10 Passenger elevator with 1900 x2000 meter shaft, machine room less, 1.0 MPS speed, 4
1 NDSR 1 No. Stops Approx. 15 m travilling distance, car entrance and door opening for stracture with
Automatic with Centre opening ACVVVF Motor Door operator with electronic / infrared sensor No. 6 22,64,324.00 1,35,85,944.00
door detector, all floor opening in same side ,moon rock finish stainless steel and PVC
Flooring with complete all respect as per specification.
(i) Necessary wiring/control wiring, conduit/raceway if required for satisfactory operation of
elevators shall be in the scope of lift vendor.
(ii) Size of car should be fit in lift well.
TOTAL CARRIED TO SUMMARY 1,35,85,944.00
Sign of Contractor Page 51 of 52 NBCC
Digitally signed by ANUJ
TENDER FOR "CONSTRUCTION OF MULTISTORIED BUILDING TO ACCOMMODATE SIX COURTS INCLUDING XI ADDITIONAL DISTRICT COURT AT GUDIVADA,
KRISHNA DISTRICT, A.P".
Items Ref. (DSR- DSR NON DSR
Sl. No. Description Unit Qty Rate in Rs.
2022) Amount in Rs. Amount in Rs.
Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic
Power Plant conforming to MNRE specifications as amended, consisting of
Mono/ Poly Crystalline silicon solar cells, net metering facility, necessary
protections, earthing, mounted on Aluminium/ GI structure of suitable strength
with following components complete as required:-
a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in
India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-
Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than
16.5%. PV modules used in solar power plants/ systems must be warranted for
their output peak watt capacity, which should not be less than 90% at the end of
10 years and 80% at the end of 25 years.
1 (DSR-2019) OR b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400
25.1 (DSR- 2022) V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate
AC Power with efficiency not less than 97%, total harmonic distortion less than
3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall
adjust the voltage and frequency level to suit the Grid Voltage Frequency.
d) Fixing of Array junction box & Main junction box with IP 65 protection and
termination arrangement for incoming and outgoing cable along with glands, lugs
and other accessories etc. as required.
e) Lightning and surge voltage protection. f) Connections & Interconnections by
supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade
armoured power and control cables between solar modules, main power cable to
grid supply PCU unit along with supplying & fixing of necessary channel/conduit
lugs and other accessories etc. as required.
Sign of Contractor Page 52 of 52 NBCC
Digitally signed by ANUJ
aoc.pdf
Download all tender documents and submit your bid