Construction of Archaka Quarters at Sri Abhaya Anjaneya Swamy Temple, Badrirajupalem (V) Thotlavalluru (M), Krishna District.

Earth work excavation for foundations (Manual Means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and 1m additional lift charges over the initial depth up to 3m including all operational,incidental, labour charges such as shoring, sheeting, planking, strutting etc., and overheads & contractors profit complete for finished item of work excluding seigniorage excluding dewatering charges etc., as per SS 20 B(APSS 308)

Filling with carted filling sand in trenches,sides of foundations and basement with initial lead in layers not exceeding 15cm thick, watering and ramming including cost and conveyance of water to work site and all eraitonal, incidental,labour charges,hire charges of T&P etc., and overheads & contractors profit complete for fnished item of work(APSS NO.309&310)

Plain Cement Concrete (1:4:8) (cement: fine aggregate: Coarse aggregate) for foundations and under flooring bed using coarse aggregate 40mm size hard machine crushed granite from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, excluding seigniorage charges, sales & other taxes on all materials and including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and overheads & contractors profit complete for finished item of work. (APSS No. 402)

VRCC M-20 grade nominal mix (cement :fine aggreegate: coarse aggregate) corresponding to table 9 of IS456 using 20mm size graded machine crushed hard granite metal (coarse aggreegate) from approved Quarry including cost and conveyancej of all materials like cement, fine aggregate(sand) coarse aggregate, water etc, to site and excluding seigniorage charges,sales and other taxes on all materials including all operational incidental and labour charges such as machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges and including overhead and contractor profit etc., complete for inished item of work, but excluding centering shuttering: First Floor

(d) Plinth Beam

(f) Roof Slab 120mm thick

(g) Stair case slab 150mm

(i) Plain Sunshade

Providing High Yield Strength Deformed (HYSD) (Fe 415 grade as per IS 1786-1979) of different diameters for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc.,and overheads! & contractors profit complete for finished item of work in all floors.( APSS No.126)

Brick masonry for panel walls in superstructure with CM (1:6) prop: (Cement Screened sand) using common burnt clay bricks of class as per Table- I of IS:1077- 1992, Non-Modular or traditional size 23 x 11 x 7 cms from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all; materials like cement, screened sand, bricks, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc.,and overheads & contractors profit complete for finished item of work. (APSS No. 501 & 504).

Plastering 12mm thick single coat in CM (1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site, excluding seigniorage charges, sales & other taxes on all aterials, and all operational,, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Plastering 20 mm thick single coat in CM (1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials, and all operational, 7 incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Ceiling Plastering 12 mm thick single coat in CM(1:3) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Providing impervious coat to exposed RCC roof slab surfaces to required slopes with CM (1:3) prop. using screened sand 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by Engineer-in- charge at 1 Kg per one bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand, water proofing compound, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials and operational, incidental, and labour charges for mixing mortar, laying, lift charges, rendering smooth and thread lining, curing including rounding off junctions of wall and slab etc., and overheads & contractors profit complete for finished item of work. (APSS No. 901 & 903).

Supply and fixing doors as per drawings with medium teak wood frame of section 100mm x 65 mm and ISI marked flush door shutters of 30 mm thick double shutters with bond wood solid block board type Core having cross bands and face veneers, hot pressed, bonded with water proof phenol formaldehyde synthetic resin factory made conforming, to IS 2202-1991 (Part-1) both sides commercial ply with internal lipping on all sides! including cost and conveyance to site of teak wood frame, flush shutter including supply! and fixing 6 Nos. MS Z hold fasts of size 300 mm x 40 mm x 5mm including cost of ISI' 8 marked MS powder coated fixtures of 6 Nos. butt hinges (IS:205) 150mm long, 1 No. aldrop (IS:2681) 300mm long, 2 Nos. tower bolts (IS:204) of 200 mm x 10 mm dia at top, 2 Nos. 150 mm long handles (IS:208), 2 Nos. door stoppers and 2 Nos. rubber bushes including fixing the fixtures to door with required number of screws, bolt and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame! etc, including overheads & contractors profit complete for finished item of work as per APSS 1001 & 1002 (The vertical frame of door shall be embedded in flooring for a depth of not less than 10 mm)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50m in height dimension comprising of uPVC multi chambered frame with in-built roller trackand sash extruded profiles duly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVCprofile),appropriate dimension of uPVC extruded glazing beads and uPVC extruded inter locks, EPDM gasket, wool pile,zin calloy(white powder coated) touch locks with hook,zinc alloy body with single nylon rollers (weight bearing capacity to be 40kg),G.I fasteners 100x8mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile offrame & sash shall be mitred cut andfusion welded at all corners, including drilling of holes forfixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished walls shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer -in -Charge inclusive of cost of Single/double glasspanes, wiremesh and silicon sealent .Note: For uPVC frame-and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly-proof SS wire mesh (Two nos. glazed & one no.wire mesh panels) made of (small series) frame 92 x44mm & sash 32 x 60 mm both having wall thickness of 1.9 ±0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing 38mm thick BRAND FACTORY MADE MOULDED DOOR SHUTTER Consisting of sold core single leaf flush door of 30mm thickness, Hipped with 15mm (SmmX3) thick X 30mm width on one stiles and top falls and 10mm (5mmX2) thick & 30mm width on the other stiles and bottom rails. The inner panel laminated with 2mm thick termite proof, water proof and fire resistant moulded Pac sheet with 2,4,6 raised panel design in different panel and/or prelam colours on one side after routing the moulded design on flush door and 2mm prelam Pac sheet on other side using rubber adhesive on flush door and solvent cement adhesive on Pac lipping etc. complete as per 14 direction of Engineer-in-Charge, manufacture specification and drawing and Providing and fixing factory made Pac single side Prelam door frame of the size 50X47 mm with a wall thickness of 5mm, made out of extruded Smm rigid Pac single side prelam sheet, meter cut at two corners and joined with 2nos. of 150mm long brackets of 1515mm MS.Square tube. The two vertical door profiles are to be reinforced with 19x19mm MS. square tube of 19guage. The door frame shall be fixed to the wall using 65/100mm long MS. Screws through the frame by using Pac fasteners, a minimum of 4nos. of screws to be provided for each vertical member and minimum 2nos, for horizontal member etc complete as per manufacture specification and direction of Engineer-in-charge.

Flooring with Non-skid red or white full body Ceramic floor tiles of Size 300 mm x 300mm and thickness between 7-8 mm and 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts1to15) of any colour and finish in all shades and designs 7.30mm thick, 1st quality and of size as approved by Engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per Sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand, water and tiles etc., and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707)

Providing dadooing to walls with supply of screw sles of size 300 620 with of auch wwwble www. wooden bamboo stone mishes a lessee and thickness we tequality conforming to 94372/8237428433 (s) of any olour and fraish in all shades and designs as approved by the age-age set over base coo CM(13) 12 mm thick using screened sand with century of honey like consistency spread at the rate of 3.30 ks per sanding with white cement paste med with pigment of matching shade to full depth, including cost of all materials like Nes, ceme sand and water etc, complete excluding segelorage charges etc, and overheads & contractors profit complete for fished item of work

Flooring with glazed vitrified tiles with matt finish of size 600x600 mm and thickness between 9-10 nim 1st quality confirming to IS:13711, IS:13712, IS:13630 (Parts 1to 15) of any colur and finish in all shades and designs. as per the approved flooring pattern as directed by the Engineer-In-Charge, laying tiles using spacers of 2mm thick, set over a base coat of GM (1:8) prop. 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistancy spread @ 3.3 kgs 10 per Sqm. and jointed neately with white cement paste to full depth mixed-with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) including cost of seigniorage charges on all materials, cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707)

Flooring with polished shahabad / Tandur stone slabs of 15mm to 18mm thick 0.457m x 0.457m or any other size as specified set over a base coat of CM (1:8), 12mm thick using screened sand over already laid CC bed / RCC roof slab including neat cement slurry of honey like consistency spread @ 3.3 Kgs per Sqm and jointed with neat cement to full depth including cost and conveyance of all materials like cement, sand, water, flooring stones etc. complete i, sales & other taxes on all materials including all labour charges like dressing of flooring stones to the required size, mixing of cement mortar, laying, lift charges, cost of base coat etc., and overheads & contractors profit complete for finished itein of work. (APSS No.703

Supply & application of one coat of deco orient base & two coats of acrylic exterior emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/litre for exterior walls including cost and conveyance of all materials to site, sales & other taxes, incidental, operational and all labour charges etc., and overheads & contractors profit complete for finished item of work in all floors.

Supply & Fixing of 48" (1200mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, Input voltage 230V AC converted to 24 V DC, power Input not more than 30W, air delivery not less than 220 cubic meter/min and a minimum 16 service value of 7.0, with remote and without Regulator, including all labour charges overheads & contractor profit etc., complete Makes: Atomberg(GV2 / Halonix (Plasma) /Havells(Efficiencia Neo)/ Crompton (EN Groove) /Superfan (E281) / RUP(Ecowise)xluding sales & other taxes etc.

Supply and fixing of concealed box PVC/MS with hook for fan Supply and fixing PVC/MS galvanished Fan hook box with hook including all Labour charges etc., complete. Excluding sales & other taxes but including overhead & contractor profit etc.exluding sales & other taxes,etc., complete.

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220-260 Volts, with high power LEDS, having System Efficacy of >=100 lumens/watt, PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, 18 etc., complete with earth connection and not less than two years warranty along with Tw/PVC round blocks, supply of No:8 screws of 35mm, supply of PVC rawl plugs & supply. of ISI marked 23/0060 twin core twisted / Flat heavy copper cable wire. Makes: As per list of recommended brands as category including overhead & contractor profit etc.exluding sales & other taxes, etc., complete.

Supply and fixing of 9W LED Lamp input voltage 90 to 300V, Color temperature 3000k 6500k, Beam angle 170 220 degrees, B22 base, along with supply of batten 19 holder/slanting holder ISI Marked in lieu of ceiling rose of light point complete with all connections and all labour charges with 9W LED bulb (for new installation). including overhead & contractor profit etc.exluding sales & other taxes, etc., complete.

Supply and fixing of 2 Nos 16A/6A, 1 way, Combi Socket Modular Socket with shutter ISI Marked and 2 Nos 6A / 10A, 1 Way, 1 Module, Modular Switch ISI mark on existing 20 Modular board including earth connection and all labour charges etc., complete on wall. Seperate Modular Switch board including overhead & contractor profit etc.exluding sales & other taxes, etc., complete.

Supply of run of 2 of 22/0.3mm (1.5 Sq.mm) ISI marked FRLS/ FRLS-H/HFFR/ZHFR PVC insulated flexible copper cables 1100V grade as per IS: 694/1990 & IS:17048/2018 21 specification for copper cable in existing pipe for mains inlcuding all labour charges etc.,including overhead & contractor profit etc.exluding sales & other taxes, etc., complete

Supply and wiring with 2 run of 1.5 Sq.mm ISI marked FRLS/ FRLS-H/ HFFR / ZHFR PVC insulated flexible copper cables 1100V grade as per IS: 694/1990 & IS:17048/2018 specification for copper cable in existing pipe with supply of 6A/10A 1 way 1 module Modular Switch, 3 Plate Jumbo Ceiling Rose and Modular switches with cover plate and Gl switch box including all labour charges etc., complete for light, bell, fan and exhaust fan points, including overhead & contractor profit etc.exluding sales & other taxes, etc., complete. Non-Residential Buildings. [Makes as per approved list in prevailing SOR under Category-I for Switches/ Sockets and Category-I for Copper Cables]

Supply and fixing 4 Way SPN Distribution board with IP-43 protection (Metal Door) suitable for 1 No. 40 A single phase ELCB / RCCB/DP Isolator as incomer and 2 Nos. 6-32 A 23 10kA SP MCBs as outing going including internal connection and labour charges for surface/flush mounting etc., including overhead & contractor profit et exluding sales & other taxes,etc., complete.

Providing independent earthling by excavating a trench to a depth of 2.1M in all solls, as per size specified in the Data, using 40mm dia 'D' class GI pipe of 2.5 Mtrs length with necessary accessories with hume pipe ring duly providing staggered holes including filling! with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete for small quarters,including overhead & contractor profit etc.exluding sales & other taxes,etc., complete.

Supply and Fixing of 25mm outer dia (1.60 -1.80) mm thickness medium grade with IS:9537-part 3 rigid PVC Condult with all accessories fixing on chromium plated metallic base saddles and along with raw plugs, 32mm screws, 25mm 1,2,3,&4 way junction boxes, 25mm PVC bends, 8 or 9 module hot dip galvanized metal boxes for switches for Light, Fan and separate plug point including all labour charges etc., including overhead & contractor profit etc.exluding sales & other taxes, etc., complete.

Supply and run of 2 of 36/0.3mm (2.5 Sq.mm) and 1 Run of 14/0.3mm (1.0 Sq. mm) ISI marked FRLS/FRLS-H/HFFR/ZHFR PVC insulated flexible copper cables 1100V grade as per IS: 694/1990 & IS:17048/2018 specification for copper cable in existing pipe for mains Including overhead & contractor profit etc.exluding sales & other taxes, etc., complete.

Supply and run of 2 of 4,Sq mm ISI marked FRLS/ FRLS-H / HFFR/ZHFR PVC Insulated) flexible copper cables 1100V grade as per IS: 694/1990 & IS:17048/2018 specification for copper cable in existing pipe for mains including overhead & contractor profit etc.exluding sales & other taxes, etc., complete.