BEAUTIFICATION AND UPRGADATION OF NEHRU STADIUM AT ROORKEE

Civil Work

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m inwidth or 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift upto 1.5 m, including getting out the excavated soil anddisposal of surplus excavated soil as directed, within a lead of 50 m.

Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Filling available excavated earth (excluding rock) in trenches ,plinth,sides of foundation etc . in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.

Supply & Filling in plinth with sand under floors including watering, Ramming consolidating and dressing complete

Providing and laying in position cement concrete 1:4:8 (1cement :4 coarse sand (zoneIII):08graded stone aggregated 40mm.nominal size.) excluding the cost of centering and shuttering - All work upto plinth level

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) All works upto plinth level

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)All works above plinth level upto floor V level

Centering shuttering including strutting, propping etc. and removal of form work Foundations, footings, bases of columns, etc. for mass concrete

Centering shuttering including strutting, propping etc. and removal of form work Columns, Pillars, Piers, Abutments, Posts and Struts

Centering shuttering including strutting, propping etc. and removal of form work Suspended floors, roofs, landings, balconies and access platform

Centering shuttering including strutting, propping etc. and removal of form work Lintels, beams, plinth beams, girders, bressumers and cantilevers

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete Thermo-Mechanically Treated bars

230th Brick work withcommon burnt clayF.P.S. (non modular) brick of class designation 75 in foundation & plinth in cement mortar 1:6

Brick work with F.P.S bricks of class 75 in super structure above structure above plinth level up to floor five level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand )

Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia. M.S.bars at every third course of half brick masonry (with F.P.S.bricks).

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Kiln seasoned and chemically treated hollock wood

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

4.0 mm thick glass panes (weight not less than 12.5 kg per sqm)

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. With decorative veneering on one side and commercial veneering on other side

12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

15 mm cement plaster on the rough side of single or half brick wall of mix

6mm thick cement plaster of ceiling of mix 1:3 ( 1 cement : 3 fine sand) mortar

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement prime

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Udaipur green marble

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: (100x75x4 mm)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

RAISING TRACK (AS/SITE)

CRICKET PITCH (AS/SITE)

Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing 5/6 A modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin 5/6 A modular socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

POWER/ COMPUTER POINT/AC- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40 Amp, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 6 way (4 + 18), Double door , horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supply and laying of 10 sq. mm 4 core aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.

Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect.

Supply and fixing of recess mounting round 15 to 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-AA

Supply and fixing of 16 SWG M.S. drum with luvers duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect.

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 Watt. Confirming to IP 66 protection complete in all respect CAT-AA

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire with driver set confirming to IP 65 and above Protection . complete in all respect. CAT-AA

supply and fixing of ceiling fan of heavy duty 1200mm approved make of Havells complete in all respects.

supply and fixing of Exhaust fan of heavy duty 230mm approved make of Havells complete in all respects.

Supply of LED Bulb 20 Watt.

Water Supply Work

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work) 15 mm dia nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore.

Providing and fixing gun metal non-return valve of approved quality (screwed end) 25 mm nominal bore (Horizontal)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet, and overflow pipes but without fitting and the base support for tank.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15mm nominal bore.

Supply of 1 HP 50 LPM Pump to deliver 1000 lpd water at 42 mtr head, complete with 1.0 meter cable complete in all respects.

Supply of pump controller (Control panel cum Starter with automation) suitable for above motor as per following para meters. KSB make.

Supply of main piping & valves comprising of the following:- i. 25mm dia Wheel Valve 2 Nos. ii. 25 mm dia Reflux valve 1 No. iii. 25 mm dia Bend 90º - 1 No. iv. 25x25x25mm dia Tee A/F – 1 No. v. MSDI clamp – 1 Set vi. Gauge with fitting – 1 Set

4 sq.mm x 3 core copper flexible cable and mcb bend swich pvc condut pipe etc complete.

Supply and fixing of the following material required for construction of bore hole, installation of hand pump, development, testing and construction of plat form drain etc. complete excluding cartage.

India Mark-II Hand Pump Machine.

110 mm dia P.V.C. Pipe 6 kg/Cm2

32mm dia G.I. medium quality pipe

Construction of 150 mm dia bore hole by Palm pressure method in soil mixed with Kankar, Bajri, Boulder etc. including development of bore by over Pumping and back washing till the discharge is free from turbidity including hiring charge of pumping equipment after this erection of Boring, Dismantalling after completion of work also Lowering of PVC pipe assembly in 150 mm dia bore hole required for jointing the various components and lowering then in the bore hole up to depth.

0 to 70 Meter

Embossing should be done over the hand pump assembly as per departmental circular, as per instructions of the Engineer In charge, including all labour& materials T&P

Disinfections of hand pump using powered chlorine including throw cleaning of all exterior parts of hand pump coming in contact with water, including supply of bleaching powder.

Surrounding & packing graded coarse sand in between the bore hole and the stainer up to three meter depth from the bottom of the strainer including supply of coarse sand , including all labour, jointing materials T&P etc required for proper completion of the work. loading and unloading arrangement etc. complete. Excluding materials.

Sealing of annular space between the housing pipe and the bore hole in single continuous operation with puddle clay, bentonite clay andcement concrete as per drawing supplied by the department including supply of all material, labour T&P etc. required for completion of work.

Drainage Works

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded 150 mm diameter S.W, pipe

Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I. With F.P.S Brick class designation 75

Constructing brick masonry chamber for and bends with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With F.P.S. bricks with class designation 75

SANITARY WORKS

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front: One urinal basin with 5 liter white P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good. White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing trap of self cleansing design with screwed down or hinged 100 mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 1729

Providing and fixing soil, waste and vent pipes Sand cast iron S&S pipe as per IS: 1729.

100 mm dia.

75 mm dia.

SEPTIC TANK & SOAK PIT WORKS

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m inwidth or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) .

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) Ist step " " Baffle wall

Centering and shuttering including strutting,ropping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centering, shuttering, finishing and reinforcement . 5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Roof slab Less man hole

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

12 mm cement plaster of mix : 1:6 (1 cement : 6 fine sand)

Providing and laying cement Concrete in retaining walls, return walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc. upto floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

BOUNDARY WALL WORKS

Making of boundary wall around the (Nehru stadium)

Earth work in excavation in trenches for foundation and for pipes cables etc. in ordinary soil including fitup to 1.5m and dressing of sides and ramming bottoms and disposal of surplus excavated earth as directed by the engineer with in a lead of 50m.

Filing available excavated earth in trenches ,plinth,sides of foundation tec.in layers not exceeding 20cm in the depth ,consolidation each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Providing and laying in cement concrte 1:4:8(1cement :4fine sand:08graded brick aggregated 40mm .nominal size.) and curing complete excluding cost of form work in foundation and floors.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :.1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

230mm thick brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:6 ( 1 cement : 6 coarse sand).

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete TMT.

15mm thick plaster on the plain in side of mix 1:6 mortor

Colour washing such as green, blue or buff to give an even shade : New work (two or more coats) with a base coat of white washing with lime.

Centering shuttering including strutting, propping etc. and removal of form work

FOUNDATION UP TO PLINTH.

COL SUPER STRUCTURE.

Supply & fixing gate Main building including all matrials & labour etc.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work .

Making of Boundary wall around the (Nehru stadium) as per Drawing 3 meter

PAINTING WORKS

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Minor Plaster /Patchwork : Minor Structural repair like plaster 1:6 (1 cement: 6 coarse sand) Smoothening of surface Surface after applying plaster & sanding machine ( if needed ) Minor plaster works / Patchworks at 1:6 (1 cement: 6 coarse sand) including ladders / scaffolding etc. complete as per directions of Engineer in charge.Upto a height of 3 metre

Base Preparation for artwork : Preparation & Finishing walls with Premium Acrylic Smooth exterior paint (Two or more coats ) with Silicone additives of required shade . Priming coat of premium exterior primer of reputed manufacturerof with high color fastness rating to withstand outdoor conditions is required to cover existing dark or bold color on the wall or to reseal an unpainted porous surface including ladders / scaffolding etc. complete as per directions of Engineer in charge.Upto a height of 3 metre

Artwork Generation & Art Painting : Recci, Designing , generating mockups and submission of Presentations in printed form with site specific details and challenges ( if any ) / via email for approval from design approval commitee to be in scope of the Agency . The Works should be designed considering the real time dimensions and scaling of the areas and locations identified. Painting of approved artwork by proffessional artists with Premium Acrylic Smooth exterior paint of required shades of reputed manufacturer with high color fastness rating to withstand outdoor conditions . Use of spray cans / Stainers of reputed manufacturer is allowed (with proper disposal mechanism of the same) including ladders / scaffolding etc. complete as per directions of Engineer in charge.Upto a height of 3 metre

Varnishing : Top Coat over artwork to preserve the life and also to provide the grace / required lusture with a protective layer for easy cleaning of the artworks . Prior test & observation on wall with thorough process to be done before application . Varnishing with varnish of approved brand and manufacture One or more coats as per recommendation of the paint manufacturer . Responsibility of chipping of artwork / flaking due to varnish will be of the agency including ladders / scaffolding etc. complete as per directions of Engineer in charge.Upto a height of 3 metre

TOILET WORK

Earth Work

surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish. Lead up to 50 m and lift up to 1.5 m.

earth work in excavation by mechanical means (hydraulic excavator ) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the exacavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kinds of soil.

Filling available excavated earth (excluding rock) in trenches ,plinth,sides of foundation etc . in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Diluting and injecting chemical emulsion ( chlorpyriphos/Lindane E.C 20% with 1% concentration ) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under floor, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 part-II . (plinth area of building shall be measurd for payment.)

supplying and filling in plinth with jamuna sand under floors including, water, ramming consolidating and dressing complete.

CONCRETES WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

REINFORCED CEMENT CONCRETE

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level

1:1,5:3 ( 1 cement : 1.5 coarse sand : 3 grade stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement above plinth level up to 5 floor

raeinforcement for R.C.C work including straightening, cutting, bending ,placing in position and binding all complete. T.M.T

centring and shuttering including strutting, ropping etc. and removal of form for

foundations, footings, bases of columns, etc. for mass concrete.

suspended floors, roofs, landings, balconies and access platform

lintels , beams , plinth beams , girders, bressumers and cantilevers

columns , piliars , piers, abutments, post and struts

BRICK WORK

Brick work eith F.P.S bricks of class designation 75 in foundation and plinth in

cement mortar 1:6 ( 1 cement : 6 coarse sand)

brick work with F.P.S . Bricks of class designation 75 in superstructure

cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and fixing pressed steel door frames conforming to IS: 351, manufactured from comercial mild steel sheete of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50*25mm, or base ties of 1.60mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: profile B fixing with adjustable

Providing and fixing factor made ISI marked steel glazed doors, windows and ventilators side/top/centre hung with beading and all members such as K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and 15x3mm lugs. 10cm long, embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1 cement :3 coarse sand:6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plgs and screws or with fixing clips or with bolts and nuts as requred.

Providing and fixingf ISI marked flush door shutters conforming to IS:2202 (Part 1) non decorative type, core of block board construction with frame of 1st class hard wood and well m,atchef teak 3 ply veneering with vertical grains or cross bands and face veneers n both faces of shutterts. (35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws complete: 125mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary secrews etc. complete

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary secrews etc. complete Twin rubber stopper

Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:4 ( 1 cement : 4 coarse sand)

STEEL WORK

Providing and fixing M.S.Tubular frames for doors, windows, ventilators and cupboard with L-Type section made of 1.60mm M.S. Sheet, joints mitred and welded and grinded finish profi required size with 15x3mm lugs 10cm long embedded in ce concrete blocks 15x10x10cm of 1:3:6 (1 cement : 3 coarsegraded stone aggregate 20mm norminal size) or with wooden plugs screws or rawl plugs and screws or with fixing clips or with b nuts as required including fixing of necessary butt hinges and applying a priimg coat of approved steel primers.

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5mm hick glass panes. (D.S.R.10.30.20)

windows using galavanished M.S. wire gauge with average width of a in both directions with wire of dia. 0.63mm. With 12mm mild steel U beading.

FLOORING

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation , levelling & dressing & finishing the top smooth. (D.S.R.4.17)

Provinding and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacture) with water absorpiton's less than 0.08% and conforming to IS: 15622 approves make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size of Tile 60x60 cm

Provinding and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approves make in all colours, shades except burgundy, bottle green, black of any size as approves by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

FINISHING

15mm cement plaster 1:6 (1 cement : 3 fine sand) on wall

12mm cement plaster 1:6 (1 cement : 3 fine sand) on wall

6 mm cement plaster 1:3 (1 cement : 3 fine sand) on ceiling

Grading roof for water proofing treatment with Cement Concrete mortar 1:3 ( 1 cement: 3 coarse sand)

Distempering with oil bund washable distemper of approved brand and manufacture to give an even shade (New york (two or more coats) over and including priming coat with cement primer)

Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives of required shade New Work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg?10 sqm)

Painting wood work with deluxe multi surface paint of requird shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand or manufacture.

Painting steel work with deluxe multi surfacepain to give an even shade. Two or more coat applied @0.90ltr/ 10sqm over an under coat of primer applied @0/80 ltr/ 10 sqm of approved brand or manufacture

WATE R SUPPLY

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. linternal work-Exposed on wall 15mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (External work)

15mm dia normal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8930

15mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8930

15mm nominal bore

providing and fixing gun metal non-return valve of approved quality (screwed end)

25mm nominal nore (Horizontal)

Providing and placing on terrace (at all floor levels) polythene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and makin necessary holes for inlet, outlet, and overflow pipes but without fitting and the base support for tank.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS

15mm nominal bore

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete including cuttting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

Providing and fixing white vitreous china pedastal type water closet (European Type

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or walll corner type lipped front

One urinal basin with 5 liter white P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including paintiing of fittings and brackets, cutting and making goods

White Vitreous China Wash basin size 630x450 mm with a single 15mm C.P. brass pillar tap.

Providing and fixing trap of self cleansing design with screwed down or hinged

100mm inlet and 75mm outlet

Sand cast iron S & S pipe as per IS: 1729

Providing and fixing soil, waste and vent pipes sand cast iron S & S pipe as per IS : 1728

75mm dia