PROVN OF REST ROOM FOR AIRMEN MESS, ROLLING SHUTTERS, FIRE ALARM SYSTEM, LIGHTENING ARRESTOR, EXHAUST FAN FOR CERTAIN SMQs ALONGWITH SPECIAL REPAIR TO COVERED SHED AT MGR AND SGR AT AF STN BHUJ

Amount

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes pier holes etc not exc. 10sqm on plan and not exc 1.5m in depth and getting out in Hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (M-30 Design mix) (using 20 mm graded stone aggregate) in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete all as specified and directed by Engineer-in-Charge

Material & labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (M-30 Design mix) (using 20mm graded stone aggregate) as in beams, cantilevers, bressmummers, lintels over 1.5 m span complete all as specified and directed by Engineer-in-Charge.

Material & labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (M-30 Design mix) (using 20mm graded stone aggregate) as in columns, pillars, posts, struts etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished , square, rectangular or polygonal surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (M-30 Design mix) (using 20mm graded stone aggregate) as in slabs supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

Material & labour for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Returning filling in foundation/filling under floor ,including spreading, levelling, watering and well ramming in layers, not exc 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil at a distance exc. 500 m but n.exc.1.50 km and depositing/spreading and leveling where directed at a level n.exc. 1.5m above the starting points complete all as specified and directed by Engineer-in-Charge.

Material & labour for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engineer-in-Charge.

Material & labour for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed by Engineer-in-Charge.

Material & labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure) complete all as specified and directed by Engineer-in-Charge.

Material & labour for treating the top surface of filled earth of plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing 100 mm thick Cement concrete, type D2, (1:4:8), (using 40mm graded stone aggregate) in sub base floor complete all as specified and as directed by Engineer-in-Charge.

Material and labour for kota stone slab 20-25mm thick (mirror polished) in riser of steps, skirting, dado and pillar laid over cement screed and jointed including mortar cm 1:4 for 10 mm thick includig nosing, bell mouth, making grooves as required complete all as specified and as directed by Engineer-in-Charge.

Material & labour for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight)c complete all as specified and directed by Engineer-in-Charge.

Material & labour for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

Material & labour for precast cement concrete block masonry with solid blocks exc 10cm in width Type (1:5:8) (using 20mm graded stone aggregates) and setting in cement mortar 1:4 in walling complete all as specified and as directed by Engineer-in-Charge.

Material & labour for rendering 10mm thick in CM 1:6 on PCC block masonry surfaces finished even and smooth without using extra cement internal surface complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 15mm thick in two layers first coat 10mm thick in CM 1:6 and second coat 5mm thick in CM 1:4 with wate proofing compound @3% by wt of cement on fair faces of brick work or concrete surfaces, finished even and fair complete all as specified and directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.

Material & labour for rendering 5mm thick in CM 1:3 on concrete surfacves/ chajja/ ceiling, etc as in ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion, white or tinted including one coat of wall care putty by finishing the surfaces even and smooth complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing newly plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing newly plastered or unplastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed by Engineer-in-Charge.

Material & labour for 10 mm thick screed bedding in cement mortar 1: 4 on concrete surfaces, finished fair & even including mixing water proofing compound @ 3% by wt of cement or as per manufacturer's instns complete all as specified and directed by Engineer-in-Charge. Note- WPC to be measured separately as supply only

Supply only water proofing compound complete all as specified and directed by Engineer-in-Charge.

Material & labour for vitrified ceramic dark shade 10 mm thick (sqaure/rectangular) area of each tiles n.exc. 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match existing tiles and including 15 mm thick screed bed or bedding layer of mortar 1:6 for laying floor finishes complete all as specified and directed by Engineer-in-Charge.

All as per Ser Item No 31 above but in vertical surfaces such as dado, skirting and riser including rendering 10mm thick in CM 1:4 etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for non skid ceramic digital pattern coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exc. 0.06 Sqm but n.exc. 0.18 Sqm as per IS - 13755 in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed 15mm thick in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Material & labour for glazed digital pattern ceramic coloured tiles Ist quality in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over incl for 10mm thick rendering on vertical surface in cement motar 1:4 as backing coat complete all as specified and directed by Engr-in-Charge.

Supply & fix 20 mm dia fancy type PVC coated best quality draphery rods for curtains fixed to wall with screws complete all as specified and directed by Engineer-in-Charge.

Supply & fix pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock stricke plate etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats thickness of shutter in 25 mm 1st class of hardwood complete all as specified and as directed by Engineer-in-Charge.

Supply & fix 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters factory made, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

Supply & fix stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih stainless steel wire staples complete all as specified and directed by Engineer-in-Charge

Supply & fix SM butt hinges medium weight cold rolled 100 mm size complete all as specified and directed by Engr-in-Charge.

Material & labour for mild steel barrel tower bolts stove enamelled black with bright bolt and fixed 200mm length of bolt complete all as specified and directed by Engineer-in-Charge

Supply & fix aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed size 300mm long complete all as specified and directed by Engineer-in-Charge.

Supply & fix 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply & fix floor door stopper of brass body and tongue with hard drawn steel spring, overall length of cover plate 150mm and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new surfaces wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer on wooden surface complete all as specified and directed by Engineer-in-Charge.

Supply & fix TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & fix TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Material & labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china wash basin, angle back, size 550x400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engr-in-Charge.

Supply & fix pillar taps of 15 mm bore, fancy type with capstan head, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix 2 way bib cock for hand faucet with wall flange complete all as specified and directed by Engineer-in-Charge.

Supply & fix waste pipe of 32mm dia PVC pipe for WHB with long screwed shanks and fly nut flange end beddedd in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix aluminium anodised tubular towel rail 20mm dia D Type 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china wash down water closet pan (pedestal pattern) white (excluding, flushing cistern and flush pipe) complete connected to p trap complete all as specified and directed by Engineer-in-Charge.

Supply & fix plastic water closet seat cover, white or black colour closed pattern with flat bottom including taking down old seat cover complete all as specified and directed by Engineer-in-Charge.

Supply & fix health faucet (ABS body) mild steelchromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and as directed by Engineer-in-Charge.

Supply & fix grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and as directed by Engineer-in-Charge.

Supply & fix PVC low level valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, flaot and handle including brackets of 10 Ltr capacity complete all as specified and directed by Engineer-in-Charge.

Supply & fix brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed for size 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Supply & fix shower rose for 15 mm dia, 125mm long, cast chromium plated screwed down high pressure with long shank screwed end for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC connection 450mm long with check nut for wash hand basin etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors complete all as specified and directed by Engineer-in-Chargeof following size :-

110mm bore

75mm bore

Supply & fix PVC sockets equal, ISI marked, IS-14735, jointed with solvent cement of complete all as specified and directed by Engineer-in-Chargeof following size :-

110mm bore

75mm bore

Supply & fix PVC bend equal of any radius with door, ISI marked, IS-14735, jointed with solvent cement for 75mm size pipes complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC bend equal of any radius with door, ISI marked, IS-14735, jointed with solvent cement for 110mm size pipes complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC gully trap 110 mm, setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC vent cowl 110 mm bore. complete all as specified and directed by Engineer-in-Charge.

Supply & fix CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls and ceilings or laid in floors concealed complete all as specified and directed by Engineer-in-Chargeof following size :-

20mm bore

15mm bore

Supply & fix stop valve 15 mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 500 ltrs also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms) complete all as specified and directed by Engineer-in-Charge.

Supply & fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening complete all as specified and directed by Engineer-in-Charge.

Supply & fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed by Engr-in-Charge.

Supply & fix magnatic catcher of size 20mm x 50mm suitable for cup board/kitchen cabinet shutter complete all as specified and directed by Engineer-in-Charge.

Material and labour for aluminium window and ventilator with side hung shutter for glazing and gauging and frame with one or more rebates made out of JINDAL/ INDAL anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) complete all as specified and directed by Engineer-in-Charge. (Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately .

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for Plywood 12mm thick grade BWR type BB fixed with screws to timber frame ,Al frame etc complete all as specified and directed by Engineer-in-Charge.

Supply only for decorative Laminate type 1 of any thickness of surface finish, colour and pattern as approved, fixed with approved adhesive on plywood as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs brass mortice lock, vertical type, size 100 mm , 4 levers with 2 keys complete all as specified and directed by Engineer-in-Charge.

Material and labour for fillet work using 2nd class hard wood exc 6 & n. exc 13 sq.cm fixed with screw, plane fillet square, rectangle in section clean swan, secuared with nails or brads complete all as specified and directed by Engineer-in-Charge.

Material and labour for external teak wood lipping 6 mm thick fixed with nails complete all as specified and directed by Engineer-in-Charge.

Material and labour for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in bed to drain pipes of size 150 mm bore, including packing under & haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engr-in-Charge.

Material and labour for cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in surface channels, drains (forming fair finished channel shall be measured and paid for separately). complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick in CM 1:4 on block masonry surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. .

Material and labour for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc complete all as specified and directed by Engineer-in-Charge. (Reinforcement shall be measured and paid for separately). .

Supply & fix reinforced cement concrete pipes 150 mm dia, class NP2 including collars laid in trenches and jointed with CM 1:1 complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains of 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( ½ round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required. instruction complete all as specified and directed by Engineer-in-Charge.

Material and labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade confirming to IS-694 drawn through non matelic rigid PVC heavy duty conduit in concealed (minimum 20 mm dia external) but shall be increase as per actual site requirement in accordance with clause No 19.125 of SSR Part-I), ISI marked with wall thickness not less than 1.8mm incl conduit accessories like bends, Tees, junction boxes etc fixed concelead in wall for cealing etc including 1.5 Sqmm FRLSH PVC insulated unsheathed copper wire complete all as specified and directed for the following :-

One light point controlled by one, one way switch single pole piano type .

One fan point controlled by one, one way switch single pole piano type.

One 3 pin 5 Amp socket outlet on the same board.

One 3 pin 5 Amps socket out let on independent board.

All as per item No 91 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps socket out let on independent board complete all as specified and directed by Engineer-in-Charge.

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 2.5 Sqmm single core, copper conductor drawn through and including PVC conduit ISI marked with accessories and 2.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge.(Note: Two runs of conductor with one run of earth wire and PVC conduit will be measured & paid as one unit).

Supply and fixing wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 20 W 4 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engineer-in-Charge.

Supply & fix double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 Single pole and neutral 8 ways with 200 Amp rated bus bar 240 volts powder coated complete all as specified and directed by Engineer-in-Charge. .

Supply & fix double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 Single pole and neutral 4 ways with 200 Amp rated bus bar 240 volts powder coated complete all as specified and directed by Engineer-in-Charge. .

Supply & fix of isolators, MCBs, etc. In distribution board of the following rating and capacities complete all as specified and directed by Engineer-in-Charge.

MCB SPN of 240 volts 20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Supply & fix metal body exhaust fan, AC single phase 230/240 volt of size 300 mm sweep with louvers including making hole of suitable size/alteration to the existing hole to fix the exhaust fan complete all as specified and directed by Engineer-in-Charge. Note:- Old u/s exhaust fan to be deposited in MES store yard)

Supply & fix stepped type electronic fan Regulator flush type on the existing phenolic laminated etc as reqd single pole 240 volts grade 350 watts heavy duty ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix Ceiling rose 3 phase, PVC/ Polycarbonate body complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 4 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 4 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular blank plate module 1 complete all as specified and directed by Engineer-in-charge.

Supply & fix modular switch flush type, 6 Amp. SP, one way ,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix modular socket outlet, 3 pin, 6 Amp, flush type 2 module complete all as specified and directed by Engr-in-Charge

Supply & fix modular swicth, 16 Amp flush type 1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix modular socket outlet, 3 pin, 6/16 Amp flush type 2 module complete all as specified and directed by Engr-in-Charge.

Supply & fix ceiling fan regulator 120 Watt 2 module Modular Type electronic step type 5 step 360 deg complete all as specified and directed by Engr-in-Charge.

Supply & fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct currect motor(BLDC) complete all as specified and directed by Engineer-in-charge.

Supply & fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed by Engineer-in-Charge. .

Material and labour for earthing complete with galvanized steel pipe electrode 40 mm bore, medium grade, 2.5 mtr length buried directly and preferably vertically in ground (earth pit not less than 1.25 mtr deep below ground level) with top edge of the plate not less than 0.6 meters below normal ground level, connected with 20 mm dia GI pipe by means of reducer and clamped with CI checknuts through 4.0 mm GI earth lead passing from 15 mmGI pipe all as shown in electrical plate No 2 (duly protected with 20 mm dia light grade GI pipe upto 7.5 m from the earth plate) and connected to GI steel earth plate including charcoal, dust, common salt necessary excavation in soft/loose soil, returning filling in and removal of surplus soil to a distance not exceeding 50 m from the starting point, watering pipe 20 mm dia GI light grade treated with 1 No PGI funnel, pit of PCC 1:3:6 type C-1, RCC 1:2:4 type B-1 pit cover 75 mm thick reinforced with 6 mm dia bars @ 75 mm c/c both ways and with MS handle 12 mm dia complete connected to earth test point including testing complete all as specified and directed

Supply & fix cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 6 Sqmm 2 core on wall etc. complete all as specified and directed.

Material and labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathed as earth wire continuity one fan point/exhaust fan controlled by one, one way switch single pole etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular switch 1 way 6 A 1 module complete all as specified and directed by Engineer-in-Charge. .

Supply & fix modular white cover plate with frame of module 1 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 1 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 1.5 Sqmm single core, copper conductor drawn through and including PVC conduit ISI marked with accessories and 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge.(Note: Two runs of conductor with one run of earth wire and PVC conduit will be measured & paid as one unit).

Material and labour for detectors complying with and type certified to EN - 45 addressable type multisensory detector with heat and smoke combination with base with self built intelligence as per IS: 11360 complete all as specified and directed by Engineer-in-charge.

Material and labour for addressable sounder with min noise capacity 60 db complete all as specified and directed by Engineer-in-charge.

Material and labour for addressable manual call point resettable type complete all as specified and directed by Engineer-in-charge.

Material and labour for fire alarm control panel complying with BS EN 54 single loop panel of capacity from 99 detectors & 99 modules upto 200 detector and modules ccomplete all as specified and directed by Engineer-in-charge.

Supply & fix remote alarm monitoring system via JFC/mobile network complete all as specified and directed by Engineer-in-Charge.

Supply & fixing GI tubing light grade for mechanical protection of earth strip laid under plinths,floors, roads, paths, culverts etc. or fixed on walls or along poles or emmbeded in PCC for giving support to air termination rod by means of MS clamps with necessary bolts, nuts and washers etc complete all as specified of size 40mm bore complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement of test point terminal block made of gun metal or phosphorus bronze size 75mmx75mmx25mm drilled and screwed including 3 Nos, 8mm dia 25mm long hexagonal head screw complete all as specified and directed by Engr-in-Charge.

Supply & fix galvanised iron strip 25x4 mm with saddles and fixing screws etc for roof/down conductor above ground including joining with rivets bolts nuts washers etc complete all as specified and directed by Engineer-in-charge.

Material & labour for maintenance free earthing with the help of mechnical boring machine of 150mm dia 30 mtr depth including supply and fix 160mm dia (O.D), UPVC pipe 6Kg/sqcm rating-06 mtr long with the help of suitable size clamp with nut bolt and washer-01 No, Suppy and fix 30 mtr 50mm dia perforated GI pipe medium grade lowering in borewell with the help of Tools & Plant having suitable hole for providing good condutivity of earting and Material & labour for providing 32x6 mm GI up to 7.5mtr long complete with protected with 40mm light grade GI tubing and connect with equipment by nut bolt and bore well earthing with the help of suitable size GI nut bolt and washer etc complete including charcoal dust & salt filled in borewell for earth conductivity. Material & labour for covering of borewell with PCC (1:2:4) type B-1/brick masonry pit of size 45x45x45cm complete all as specified and give the minimum earth result 1.0 Ohm to provide any chemical etc as required complete all as specified and directed by Engineer-in-Charge. Note:(i) Earth strip and GI protection pipe upto lenght 7.5mm shall deemed to be included in rate of above item.

Material & labour for maintenance free earthing with the help of mechnical boring machine of 150mm dia 20 mtr depth including supply and fix 160mm dia (O.D), UPVC pipe 6Kg/sqcm rating-06 mtr long with the help of suitable size clamp with nut bolt and washer-01 No, Suppy and fix 20 mtr 50mm dia perforated GI pipe medium grade lowering in borewell with the help of Tools & Plant having suitable hole for providing good condutivity of earting and Material & labour for providing 32x6 mm GI up to 7.5mtr long complete with protected with 40mm light grade GI tubing and connect with equipment by nut bolt and bore well earthing with the help of suitable size GI nut bolt and washer etc complete including charcoal dust & salt filled in borewell for earth conductivity. Material & labour for covering of borewell with PCC (1:2:4) type B-1/brick masonry pit of size 45x45x45cm complete all as specified and give the minimum earth result 1.0 Ohm to provide any chemical etc as required complete all as specified and directed by Engineer-in-Charge. Note:(i) Earth strip and GI protection pipe upto lenght 7.5mm shall deemed to be included in rate of above item.

Supply & fix air termination single pointed solid copper rod 12mm dia, 300mm long mounted on GI pipe 40mm bore light grade embedded in mass PCC complete all as specified and directed by Engineer-in-Charge. (Note :G I Pipe & PCC shall be measured and paid separately.)

Supply & fix gswitch socket out let 2 in 1, 5 Amps flush type purpose 5 pin ISI marked white or ivory complete all as specified and directed by Engineer-in-charge.

Taking down U/S shutter of size 22 x 17 feet and refixing, testing and commissioning with replacement of following parts to make it fuctional as under item No 133.00 to 138.00 complete all as specified and directed by Engr-in-Charge.

Material and labour for fitment of shutter operating gear box with 3 phase motor of suitable capacity complete all as specified and directed by Engineer-in-charge.

Material and labour for fitment of control panel with phase protection and OLR protection relay complete all as specified and directed by Engineer-in-charge.

Material and labour for fitment of spring spiral cage with worm and worm gear mechanism complete all as specified and directed by Engineer-in-charge.

Material and labour for fitment of spring spiral of 2 feet length ccomplete all as specified and directed by Engineer-in-charge.

Material & labour for fitment of new shutter bracket with welding and fitting complete all as specified and directed by Engineer-in-Charge.

Repairing of shutter with alignment with quide and motor complete all as specified and directed by Engineer-in-Charge.

Taking down U/S shutter of size 22 x 16 feet and refixing, testing and commissioning with replacement of following parts to make it fuctional as under item No 140.00 to 145.00 complete all as specified and directed by Engr-in-Charge.

Material and labour for fitment of shutter operating gear box with 3 phase motor of suitable capacity complete all as specified and directed by Engineer-in-charge.

Material and labour for fitment of control panel with phase protection and OLR protection relay complete all as specified and directed by Engineer-in-charge.

Material and labour for fitment of spring spiral cage with worm and worm gear mechanism complete all as specified and directed by Engineer-in-charge.

Material and labour for fitment of spring spiral of 2 feet length ccomplete all as specified and directed by Engineer-in-charge.

Material & labour for fitment of new shutter bracket with welding and fitting complete all as specified and directed by Engineer-in-Charge.

Repairing of shutter with alignment with quide and motor complete all as specified and directed by Engineer-in-Charge.

Dismanteling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, any type of sheet complete all as specified and directed by Engineer-in-charge. Note- Dismantling of sheet in any height and any description of the work.

Material and labour for 10 mm thick multi wall polycarbonate sheet, twein-wall 10 data sheet including aluminium jointers with rubber washer of fixed with self tapping screw and washer in roof etc ccomplete all as specified and directed by Engineer-in-charge. Note- Fixing of sheet in any height and any description/location of the work.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge. Note- In any height and any description of the work.

Supply & fix framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge. Note- Fixing in any height and any description of the work.

Material & labour for preparing new or previously untreatedsteel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer on steel surfaces complete all as specified and directed by Engineer-in-charge.

Material & labour for preparation of old steel painted surfaces of any description exc 10 cm width or girth and appying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

SANJEEV ENTERPRISES (BID ID -3258907)