Construction of Haripura (SVS) Water Supply Scheme within Jal Jeevan Mission program under Bazpur Block

Rates for Construction of Haripura (SVS) Water Supply Scheme including, Supply Installation, testing & commissioning of Rising Main, Distribution System, Construction of OHT all appurtenance work etc. complete within Jal Jeevan Mission program under Bazpur Block.

CONSTRUCTION OF OHT & VALVE CHAMBER

Supply of all Materials , Labours ,T&P etc. and Construction of RCC O.H.T of following capacities (In Kiloliters) and 12m. Staging with 1.00m wide RCC staircase from G.L. to balcony and from balcony to Top Dome 1m x 1m RCC landing at suitable locations and railed with 3 rows of 20mm dia. G.I. (M) pipe on 65x65x5mm angle iron posts fixed with ladder, top to the floor inside of the tank. M.S. M.H. cover with loacking arrangement, lightning conductor as per electricity rules, water level indicator, supply and fixing of outlet, inlet, overflow and wash out pipes with necessary sluice valves, pipe pieces (including cost of materials) flooring 0.60 M wide apron, painting on tank body, vertical pipe, ladder M.S M.H. cover , ventilator column etc. Complete with approved water proofing ( apex)/ enamal paint, testing, filling water for testing purpose etc. including supply of verticle pipes and specials assuming bearing capacity as 8MT/M2 staging 12.00 meter.

Additional rates for staging per meter height beyond 12 m height including cost of all material, labour, shuttering, scaffolding T&P complete for following capacity (In Kiloliters) Over Head Tanks. Staging - 26 m (14 m above 12 m)

Construction of masonry type chamber for sluice valve Size as per type design

CONSTRUCTION OF PUMP HOUSE

Earth work in excavation by mechanical means (hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan) including dressing of sides and ramming of bottom, lift up to 1.5 mtr including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m in all kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level in 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering and shuttering finishing and reinforcement -all work up to plinth level in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 grad aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landing, balconies, shelves, chajjas, lintels, bands, plain window sills, stair cases and spiral stair cases up to floor five level excluding the cost of centering and shuttering finishing and reinforcement -all work up to plinth level in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 grade aggregate 20 mm nominal size)

Reinforcement in RCC work including straightening, cutting, bending, placing in position and binding, using Thermo-Mechanically Treated bars all complete.

Centering and shuttering including strutting, roping etc. and removal of form for edges of slabs and breaks in floors and walls under 20 cm wide circular in shape. Foundation raft & tie beams

Columns

Beams

Edges of slabs and breaks in floors and walls under 20cm wide

Provide Ist class brick in 1:6 cement and sand mortar. In foundation up to plinth

in superstructure

40mm thick DPC in 1:2:4 with cement, sand and 20mm gauge stone ballast mortar

Steel work welded built of section /framed works including cutting fixing in position applying a priming code of approved steel primer using steel its as required in gratings, frames, guard bar, ladder, railing gates and similar works. Door Chaukhat / section window

Earth filling into plinth including it's excavation.

Provide 40 mm thick PCC flooring in 1:2:4 with cement, sand and 20mm gauge stone ballast mortar.

Provide 5mm thick glass strips on flooring 20mm deep.

Provide 15mm thick plaster in 1:4 cement and sand mortar.

Provide weather coat painting (two or more coats) to give an even shade.

Painting on doors and windows (two or more coats) over and including one priming coat.

Supply and fixing of 4mm thick plane glass panes on window's including supply of nails and putty etc all complete.

Sanitary Items

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap

Providing and fixing G.I. pipes complete with G.I. fittings and clamps/c cutting and making good the walls etc. Internal work 15 mm dia nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Supply and fixing of PVC pipes for waste water and sewer pipes. 75 mm diameter

110 mm diameter

CONSTRUCTION OF INTERNAL ELECTRIFICATION OF OPERATOR ROOM

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group A

Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required. (For light plugs to be used in non residential buildings).

MAINS & SUBMAINS Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

DISTRIBUTION BOARDS, SWITCHES & MINIATURE CIRCUIT BREAKERS

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2 + 4 way, Double door

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

PART - B: LIGHTING FIXTURES AND FANS FITTINGS Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

CONSTRUCTION OF SEPTIC TANK & SOAK PIT

Earth work in excavation by mechanical means (Hydraulic Excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars

Centering and shuttering including strutting, roping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Honey-comb brick work 10/11.4 cm thick with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand).

S/Filling brick ballast 90 mm to 40 mm size

12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement : 3 fine sand)

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required. MS Manhole cover.

CONSTRUCTION OF RISING MAIN

Providing of all materials, carting from site store to site of work, Lowering into trenches with true alignment, Laying & Jointing of full length S&S Centrifugally Cast (Spun) / Ductile Iron Pipes including supply of ''EPDM" rubber gaskets conforming to IS : 5382-1985 with testing of pipe line complete. DI K-9 pipe confirming to IS:8329/2000 : 100 mm dia

Providing push-on-joints to Centrifugally (spun) cast Iron pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket: 100 mm dia

Providing and laying D.I. specials of class K-12 suitable for push-on jointing as per IS: 9523-2000 Upto 600 mm dia

Excavation in Ordinary Soil (loams, clay, sand) for foundation including lift up to 1.5 m and lead up to 30 m filling, watering and ramming of Excavated the earth into the trenches or into the sides between foundation trenches or into the plinth and removal.

DISTRIBUTION SYSTEM

Providing, Lowering into trenches with true to alignment, Laying & Jointing including specials of full lengths of HDPE Pipes of specified grade as per IS:4984-1995 and specifications, with testing of pipe line including supply of jointing materials. PE 100 PN-6 63 mm

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50metres lead as per direction of Engineer in charge - for bituminous road

Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : Water bound macadam road

C.C. Road

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer in charge. 1:3:6 or richer mix. 1.00×1.00×1.00

Cement concrete 1:3:6 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. P.C.C.1:4:8 in base 1.00×1.00×0.50

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) P.C.C.1:2:4 in top 1.00×1.00×0.50

Dismantling and reinstatement of Bituminous Road (Not PWD Road) (0.8 m x 204 m length)- 163.20 SQM

Dismantling of Flexible Pavements Dismantling of flexible pavements and disposal of dismantled materials upto a lead of 100 m, stacking serviceable and unserviceable materials separately as per Technical Specification Clause 202 By Manual Means Bituminous Courses

WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 405. By Manual Means

WBM Grading 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. By Manual Means

WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. By Manual Means

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Dense graded bituminous macadam for grading I 37.5mm nominal size (bitumen @ 4.25% by weight of total mix

Bituminous Concrete for Grading - II-13.2 mm (Nominal Size) : Bitumen @ 5.4 % of the weight of total mix

Fog Spray - Providing and applying low viscosity bitumen emulsion for ealing cracks less than 3 mm wide or incipient fretting or disintegration in an existing bituminous surfacing By Mechinacal Means

Excavation in Ordinary Soil (loams, clay, sand) for foundation including lift up to 1.5 m and lead up to 30 m filling, watering and ramming of Excavated the earth into the trenches or into the sides between foundation trenches or into the plinth and removal. 63 mm

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 200 mm dia nominal bore

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

CONSTRUCTION OF AIR VALVE CHAMBER

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

12 mm cement plaster of mix 1:4(1 cement : 4 fine sand)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand)

560 mm diameter C.I, cover (heavy duty) the weight of the cover to be not less than 108 kg.

HOUSE SERVICE CONNECTION

Excavation in Ordinary Soil (loams, clay, sand) for foundation including lift up to 1.5 m and lead up to 30 m filling, watering and ramming of Excavated the earth into the trenches or into the sides between foundation trenches or into the plinth and removal.Excavation =16.00x0.45x0.60=4.32 Cum

Providing of all materials, Carting from site store to site of work, Laying & Jointing of G.I screwed pipes (including supply of all jointing materials like specials, white lead, hemp and oil etc) in trenches with its cutting, threading and testing of pipe line etc complete. G.I. PIPE CONFORMING TO IS : 1239 (PART-1) Medium Duty (Class 'B') 15 mm dia

Providing & fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 15 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore

Making ferrule connection in the existing main of G.I, A.C, PVC or any type of pressure mains with saddle piece, service connections, fittings and fixing of G.M. ferrule including tapping the main, but excluding the cost of earth work and cost of all materials.

CONSTRUCTION OF BOUNDARY WALL

Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement :4 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand)

Pointing on tile brick work with cement mortar 1:3 (1 cement :3 fine sand) Flush/ Ruled/ Struck or weathered pointing

Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm.

Fencing with angle iron post placed at required distance embedded incement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with 01/05/2012 - 1horizontal wires, of barbed wire 9.38 kg per 100 m (minimum) between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used.With G.I. barbed wire corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire 9.38 kg per 100 m (minimum) between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately):- Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire.

Supplying at site Angle iron post & strut of required size including bottom kilogram 73.30 41121 to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. Size 50×50×6mm

CONSTRUCTION OF 3.60 M WIDE MILD STEEL GATE WITH PILLARS

Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I, rain 100 mm diameter

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.C.C. Work Using Mild Steel and Medium /Tensile Steel Bars

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

12mm thick Plaster in mix 1:6 (1 cement : 6 fine sand)

Pointing on tile brick work with cement mortar 1:3 (1 cement :3 fine sand) Flush/ Ruled/ Struck or weathered pointing

Providing and Fixing of 40 mm dia G.I. conduit pipes including specials, cutting & threading etc. including supply of all materials, labour T&P etc. required for proper completion of the work.

Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as permanufacturers specifications Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Providing and fixing 1mm thick M.S. sheet sliding-shutters with frame and sq.m 3,452.80 43722 diagonal braces of 40x40x6mm angle iron, 3mm M.S. Gusset plates at the junction and corners 25mm dia pulley, 40x40x6mm angle and T-iron guide at the top and bottom respectively including applying a priming coat of approved steel primer.

Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm.

Provide and fixing glass panes of 28 cm × 10 cm. (2Nos.)

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Supplying and filling in plinth with sand including watering, ramming, consolidating and drassing complete in proposed water works.

CONSTRUCTION OF TUBEWELL

Transportation of suitable truck mounted rig machine, air compressor, OP unit, camp equipage ,connected T&P and necessary accessories, casing pipe ,tube well assembly housing pipe etc including loading, unloading creation and leveling of rig machine upto site of work etc complete in all respect as per direction of Engineer in charge required for drilling and development of TW

(1) Erection & Leveling of rig machine at site of work

Drilling of 550 mm dia bore by heavy duty direct rotary Rig machine in alluvial, boulders, pebbles, rocky stone, sticky clay etc from ground level upto entire depth for 300 mm dia linear assembly

Procurement of TW assembly as below (i) 300 mm dia MSERW pipe 7.90mm thick (a) Blind & Threaded

(b) Slotted & threaded

(ii) 300 mm Dia Bail Plug

(iii) 300 min Dia MS well cap

(iv) 300 mm Dia MS clamp with nuts & bolts

(v) Supply of pea gravel of size 1.6 mm to 4.8 mm

(vi) Surrounding of pea Gravels in between bore and tube well assembly upto entire depth of tube well ordered by the department

Preparing & lowering of tube well assembly starting from G.L. to the required depth including cutting, welding as required at site complete with all T&P required. (i) Fixing of 300 mm dia bail plug with Nut & U-bolt.

(ii) Lowering of 300 mm dia MSERW housing pipe (Plain & Slotted pipe) as required.

(iii) Fixing of 300 mm dia, 8 mm thick tube well cap.

(iv) Fixing of 300 mm dia M.S.D.I. housing clamp.

Dismantling of Rig Machine & Clearance of site after satisfactory completion of work.

Development of T/W by 350 PSI/1400 CFM air compressor unit to the satisfaction of Engineering in charge to give sand free discharge and proper packing of pea Gravels at least for 70 Hrs.

Development of T/W by the suitable submersible OP units complete with Lowering and lifting of pumping plant having 2000 LPM discharge approximate including running of OP unit and weld testing of tube well by V Notch atleast for 60 Hrs to the satisfactory completion of work.

DETAILS OF PUMPING PLANT

S/o Submersible pump set of 350 LPM, 75 Mt. head suitable for 300 mm dia Assembly operating at 3 phase 50Hz AC supply.

S/o Spare Pump Set of same duty.

S/o Control panel cum ATS starter complete with accessories suitable for 15 H.P.

S/o Submersible copper cable size 1x3x6 sq.mm.

S/o Main piping and valve with all accessories of 100mm size i.e. sluice valve 2 Nos., reflex valve 1No., Tee 1No., Bend D/F pipes and 100mm dia M.S. column pipe with top pipe in 3mt. Length, complete with interlocking arrangement 60Mt.

S/o Pressure gauge with fitting.

S/o Chain pulley block of 3.0 Tonne capacity 4 Mt. lift spur gear tested on 4.5 Ton load.

S/o Chemical earthing material for 15 HP pumping plant including earth electrode, aluminium earth strip etc as per I.E. rules.

S/o Main Switch 63 Amp.

S/o Rubber Insulation sheet 1 Mt.x2 Mt.x .025Mt.

S/o 25 KVA fully automatic Servo Control Voltage Stabilizer suitable for regulating incoming voltage 330 to 460Volt , outgoing voltage 415Volt with change over switch and 3Core copper cable.

Supply and fixing of Electronic type dosing system complete with solenoid coil actuated pulsar circuit, diaphragm & electronically pulp capable of delivery max, 4LPH at 5.5kg./cm2 pressure operated 220Volt single phase A.C. Supply along with chemical injection device and 100Ltrs capacity of media tank complete with accessories.

Liquid Chlorine required for six month maintenance

S/o Chlorine Testing Kit

Supply of Special tools and spanners with 2 Nos. chain wrench.

Installation, Commissioning & Testing of pumping plant and all accessories.

Intelligent GSM based Mini Remote Terminal Units/PLC with analog and digital parameters and features as specified mini T.W. and transmit data on GSM backbone. GSM based wireless Communication system capable to transfer and gather data from remote sites to master Control Stations (Voltage, Current, Power factor, Pumping running Hour etc.) with 6 Amp. Automatic Voltage stabilizer including high and low cut and isolation transformer.

Erection, testing and commissioining and modification of starter with AC and DC relays and necessary wiring complete in all respect.

Internal & external Electrification of Pump house

1 Month trial running and 5 months maintenance including watch & ward.

Ashoka