Scaling up the 1 MW Plant by additional 5 MW, Green Hydrogen Plant in DPA with capabilities to further enhance up to 10 MW in future by using Common Infrastructure Facilities – Civil Work

Name of Work: Scaling up the 1 MW Plant by additional 5 MW, Green Hydrogen Plant in DPA with capabilities to further enhance up to 10 MW in future by using Common

Infrastructure Facilities – Civil Work

Sl. No. Description Unit Quantities Rate Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not

1 exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including

getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in

depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport

3 including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as Cum 10.00 ₹ 287.91 ₹

per directions of Engineer-in-charge.

READY MIX NON-SHRINK FLOWABLE CEMENTITIOUS GROUT of reputed manufacturer to be applied under equipment/ structure

base plates etc. and for anchor bolt sleeves/ pockets etc. including chipping the concrete surface, cleaning, laying, finishing the

surfaces smooth, curing etc. complete as per directions of Engineer-in-charge and as specified Minimum crushing strength of 40 N/

mm2 and /or one grade higher than base concrete.

5 Gravel filling with approved quality 10mm size gravels brought from outside, complete as per directions of Engineer-in-charge Cum 44.50 ₹ 1,048.00 ₹

6 Providing Sand Filling below the foundations including watering, ramming, consolidating and dressing complete Cum 10.00 ₹ 1,512.84 ₹

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-30 of 600mm diameter and

length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement and

concrete but including the cost of boring with bentonite solution, empty boring, chipping and temporary casing of appropriate

7 length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, RMT 2166.00 ₹ 1,581.72 ₹

telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile

for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

9 shuttering - Plain Cement Screen Concrete (PCC): 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone CUM 564.10 ₹ 4,428.24 ₹

aggregate 40 mm nominal size)

Reinforced Cement Concrete (RCC):

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced

cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but

excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per

IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of

Engineer-in-charge.

a all works upto plinth level CUM 691.10 ₹ 6,078.66 ₹

Sl. No. Description Unit Quantities Rate Amount

b all works above plinth level CUM 10.00 ₹ 7,212.34 ₹

Reinforced Cement Concrete (RCC):

Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced

cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but

excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per

IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of

Engineer-in-charge.

12 High strength corrosion resistance coated deformed TMT bar ( Fe 500 D Grade.as per IS 1786) Reinforcement for all RCC items MT 321.90 ₹ 75,000.00 ₹

including decoiling, cutting, hooking, bending, cranking including tying system with binding wires.

13 SHUTTERING: Centering and shuttering including strutting, propping etc. and removal of form work for :

a Columns, piers, abutments, pillars, posts and struts Sqm 3042.20 ₹ 562.98 ₹

b All works upto plinth level Sqm 2414.10 ₹ 215.57 ₹

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plint and string courses fillets, kerbs and

Bituminous Paint: Providing and applying 2 coats of Bituminous Paint on conc below GL including top surface of foundations with

coal tar at least 1.2 kg/m2 per coat.

MASONRY WORK Specifications of bricks shall be fly ash building bricks of Class 7.5 confirming to IS: 13757, at all heights and

15 depths for retaining walls,wall footings, parapets, partitions, steps, drains, manholes, trenches, etc. including raking out joints

staging scaffolding and curing, etc complete as specified

a a) 230 mm thk brick masonry in CM 1:5 Cum 409.30 ₹ 6,200.00 ₹

b b) 345 mm thk brick masonry in CM 1:6 Cum 547.00 ₹ 6,200.00 ₹

Providing and laying Damp-proof course 50mm thick with cment concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate

20mm nominal size

18 mm cement plaster outside in CM 1:6:

17 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) Sqm 3075.70 ₹ 323.30 ₹

finished with a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 fine sand) finished rough with spinge.

12 mm cement plaster inside in CM 1:4:

12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand)

19 6 mm in ceiling with CM 1:3 Sqm 1899.80 ₹ 177.14 ₹

20 Water Proof cement Plaster ( 15 mm thk. ) inside the tank. Sqm 10.00 ₹ 263.66 ₹

21 POP Punning in two coats (2mm th finish surface) on the interior faces Sqm 5507.20 ₹ 150.01 ₹

22 Wall Finish: Premium anti algal weather proof acrylic emusion exterior paint with Silicon additives Sqm 3075.70 ₹ 250.00 ₹

Oil Bound Distemper(OBD) paint in Switchgear , MCC rooms , staircase

areas and office rooms (internal & ceiling)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or

more coats) over and including water thinnable priming coat with cement primer

Sl. No. Description Unit Quantities Rate Amount

Finishing walls with water proofing cement paint of required shade

New work (Two or more coats applied @ 3.84 kg/10 sqm)

IPS Floor finish with ironite hardner - 150mm thk. IPS with metallic hardener topping . I.e providing & laying 38mm thk concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) flooring plus 12mm thk ironite hardner 1:2 (1

25 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of Sqm 4296.40 ₹ 599.13 ₹

cement or as per manufacturer's specifications(To be used for floors of Switchgear rooms, electrolyser room, warehouse,

workshop, pump house etc). This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and laying Acid Alkali Resistant Tiles 600x600mmx 15 Thk of an approved, quality, make, pattern and size for areas

requireing chemical resistance conforming to IS:4457 including but not limited to provision of cement mortar(1:4) bedding

25mmthk, cutting , levelling, jointing, filling the joints in acid proof expoxy moprtar of approved coloiur& Shades,curing ,finishing

etc. complete as per manufacturer's specificaiton as directed by Engineer in charge.

27 Vitrified Tiles Flooring system with 15mm thk of 600 x 600 mm including skirting Sqm 200.00 ₹ 1,112.46 ₹

28 False ceiling system with 15mm thk gypsum board in tile form of 600 x 600 mm panels with aluminium frame supports. sqm 200.00 ₹ 1,800.00 ₹

Roof Waterproofing Over RCC surface: Water proofing in roof consist of Polyurethane (PU) water proof coating, single

component (DFT 450 micron minimum) with 25 SWG chicken wire mesh laid to slope as directed by Engineer- In-Charge.

Windows: Electro colour coated (Anodised ) aluminium frame glazed (glass min 4mm thk) window, including anodized aluminium

grill, painting as per spec. and all other fittings.

Aluminium Door: Providing and fixing in position anodised aluminium doors made of extruded tubulur electrostatically powder

coated (min. 30 microns) / anodised alluminium sections conforming to IS:733 and IS:1285 of "INDAL" or approved equivalent

manufacturer with 6.3mm laminated safety glass at top conforming to IS:2553 fixed with rubber lining or EPDM gasket and

extruded anodised alluminum beading, 100 x 45 mm bottom rails, 6.3 mm thick laminated glass glazing for top portion, bottom

portion provided with 18 gauge aluminium sheet on both the sides with plywood packing in between, 2 Nos. full width handles

mm wide x 12 mm thick to each shutter including all accessories like , beadings, locking in arrangement, etc complete.

ROLLING SHUTTER as per IS: 6248: Supplying and fixing rolling shutters of approved make, made of required size M.S. laths,

interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe

shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including

the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength

conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm

thick top cover including painting & all other fittings

Design, Fabricate supply and earect PEB structure 108M x40.43M(two bay 15.6 +24.83) c/c of steel column13.5m knee height with

33 two crain load 10T for 15.6m bay ane 15T for 24.83m bay including foundation bolts, sheeting, required rainwater knee gutter and MT 325.00 ₹ 1,35,000.00 ₹

down take pipe complate with PU coating as per client requirement.

Water Stopper: 225 x 6mm thk PVC water stopper bar in liquid retaining

PVC coated chain link fence : 3m height PVC coated chain link Fencing with galvanising & MS angle post ISA 65x65x6 at every 3m

c/c along with foundations.

MS entry gates : Providing and fixing M.S. Gate consisting of 80 dia medium MS tube frame, 50mm X 6mm MS flats welded to

frame with necessry MS clamps nuts, bolts, washers, hold fasts, 50 X 6 MS guide strips with hold fast, steel wheel, 2 coats of red

oxide zinc chromate primer and two coats of aluminium paint of approved make with necessary fabrication, fixing, to required line

and level drilling etc. complete as specified and directed.

Sl. No. Description Unit Quantities Rate Amount

RCC Hume Pipe Providing and laying to slopes and at any depth confirming to IS458 Reinforced concrete pipes with collars including

cutting out pockets for collars, jointing in 1:1 cement mortar, cutting of pipes wherever required, curing and testing of joints etc.

complete as specified and directed (excavation and back filling shall be measured and paid under relevant item)

NP2 Class 600mm dia RCC Precast pipe

100 mm th paving with M20 grade Reinforced concrete underlayed by 50mm thk. PCC(1:2:4) in the plant area. The reinforcement

shall be 8 dia bars @ 200 mm c/c in both directions centrally placed, complete as per direction of Engineer -in charge

PLINTH PROTECTION: Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse

sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from

39 natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and SQM 451.00 ₹ 477.16 ₹

consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing

the top smooth.

False flooring system -Removable type flooring shall consist of fire resistant phenol formaldehyde bonded particle board panels

40 600x600x35mm size, mounted on steel pedestals of adjustable height and supporting steel grid system to provide under floor SQM 80.00 ₹ 2,500.00 ₹

space. RCC floor slab shall be sunk to a depth 1200 mm which shall be height of the false floor system.

a) Open Brick Drain:Constructing open brick drain around the buildings as well as either side of approach roads of average size

41 450 X 500mm (average depth) laid over PCC 1:4:8 base block . Quantity per drain - PCC = 0.05 cum/m masonary works - 0.22 cum RM 1984.00 ₹ 1,546.00 ₹

/ m, plastering (12 mm th smooth finish) - 1.45 sqm / m

Gents Toilet with the following fixtures - 2 nos wash basin as per IS 2556 (IV), 2 nos frameless plate glass mirrior, 1 hand dryer,

42 soap container, 2 flat back lipped front urinals of Hindustan Sanitaryware or equivalent make and 1 WC (western type) of hindustan Nos. 3.00 ₹ 1,45,000.00 ₹

sanitaryware or equivalent make complete with all pipe fittings & fixtures

Ladies Toilet with the following fixtures -1 nos wash basin as per IS 2556 (IV), 1 nos frameless plate glass mirrior, 1 hand dryer,

soap container and 2 WC (western type) of hindustan sanitaryware or equivalent make complete with all pipe fittings & fixtures

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an

44 under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture m2 60.00 ₹ 98.04 ₹

ISA 50x50x6mm RCC Fencing

INITIAL LOAD TEST :Carrying out load tests for initial vertical compression, pullout and lateral loading including all necessary

equipment, tools and tackles, recording the pile load test results as per Consultant’s specification and as directed by Engineer-in-

Charge, and supplying the pile load test results in one original and three copies to the Consultant etc. complete on 600 mm

diameter pile ( Pile provision and installation to be paid under relevant items.)Test Loads shall be as per Geotechnical

Requirements/ Specifications/Test loads shall be

2.5 times of design load whichever is higher.

a Compression Test Nos. 2.00 ₹ 5,00,000.00 ₹

b Uplift Test Nos. 2.00 ₹ 2,00,000.00 ₹

c Lateral Test Nos. 2.00 ₹ 35,000.00 ₹

ROUTINE LOAD TEST :Carrying out pile load tests on working piles for routine vertical compression, pullout and lateral loading

including all necessary equipment , tools and tackles, recording the pile load test results as per Consultant’s specification and as

directed by Engineer-in-Charge, and supplying the pile load test results in one original and three copies to the Consultant etc.

complete on 600 mm diameter pile.Test Loads shall be as per Geotechnical Requirements/ Specifications /Test loads shall be1.5

times of design load

whichever is higher.

a Compression Test Nos. 4.00 ₹ 3,50,000.00 ₹

b Uplift Test Nos. 4.00 ₹ 2,00,000.00 ₹

c Lateral Test Nos. 4.00 ₹ 40,000.00 ₹

Sl. No. Description Unit Quantities Rate Amount

PILE INTEGRITY TEST : Conducting pile integrity load test by means of Sonic Pile testing Equipment (NDT test ) or Design Equivalent

test for 600 Dia Pile to measure Quality of pile construction, correctness of pile length, Integrity along pile length & location of

47 major defects along pile which may not only affect its load carrying capacity but also have future implication with respect to Nos. 207.00 ₹ 595.00 ₹

durability & Reinforcement corrosion including all necessary arrangements such as small impact device (Hammer), highly sensitive

accelerometer, Pile integrity tester, signal conditioning center, PIT Processer, an output device such as plotter

Approach Road : Providing and laying 3.5 m wide RCC road with 1m wide shoulder on either side as per design mix, using coarse

sand and graded stone aggregate of 40 mm nominalsize in appropriate proportions as per approved & specified

designcriteria,laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required

slope/camber,finishing with required texture, curing, making provision for contraction/expansion, construction & longitudinal joints

(10 mm wide x 50 mmdeep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete

all as per direction of Engineer-in-charge .

Specifications as below - For road - a) 200 mm th M40 RCC road with 10 dia bars @ 200 mm c/c both sides at center.

b) Underlaid by 50 mm th PCC (1:3:6)

c) Underlaid by 230 mm th graded stone boulders (approx 200 mm size max) Specifications for shoulder - Paver blocks at top,

underlaid by 50 mm th PCC (1:3:6)

Roof extractors - 4000CFM capacity aluminium fan, axial flow upward type, ceiling mounted on inclined portion for industrial use

with weather protection cowl. Motor shall be designed for zone II C category

UPVC Pipe of appoved material for Sewage lines including with laying and installation.

51 Supplying Decorative Ornamental Fiber Rotomould pot for plants of diffrent Size as Directed by Engineer Incharge

a Approx Size of 0.50 X 0.50 X 0.50 mt Nos. 200.00 ₹ 4,800.00 ₹

b Approx Size of 0.90 X 0.30 X 0.30 mt Nos. 100.00 ₹ 3,900.00 ₹

c Approx. Size of 0.75 X 0.30 X 0.30 mt Nos. 100.00 ₹ 3,200.00 ₹

d Approx. Size of 0.30 X 0.40 X 0.35 mt Nos. 100.00 ₹ 2,800.00 ₹

e Approx. Size of 0.62 X 0.39 X 0.53 mt Nos. 100.00 ₹ 4,400.00 ₹

Supplying & Planting Different Varites Of Decorative Plants of diffrent height in Landscaping Area with Sweet Earth Manure as

Directed by Engineer Incharge.

a Approx Size 0.60mtr Nos. 4320.00 ₹ 150.00 ₹

b Approx Size 0.90mtr Nos. 400.00 ₹ 900.00 ₹

c Approx Size 1.20mtr Nos. 400.00 ₹ 1,200.00 ₹

d Approx Size 1.50mtr Nos. 200.00 ₹ 1,800.00 ₹

e Approx Size 1.80mtr Nos. 200.00 ₹ 2,000.00 ₹

f Approx Size 2.40 mtr Nos. 100.00 ₹ 2,500.00 ₹

g Approx Size 3.00 mt Nos. 100.00 ₹ 2,800.00 ₹

53 Supply of portable water with transportion from private wells for road side plantation and gardening at Project Site KL 400.00 ₹ 120.00 ₹

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making

54 machine with strong vibratory compaction, of approved size. design & shape, laid in required colour and pattern over and including SQM 1440.00 ₹ 680.00 ₹

50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the Drawings

Sl. No. Description Unit Quantities Rate Amount

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required

line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves

55 (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required CUM 247.20 ₹ 5,600.00 ₹

complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C.

kerb stone shall be approved by Engineer-in- Charge

Collection of sweet earth with 5% manure (goat dropping and cow dung dried) free from foreign materials subject to the approval

56 of Engineer-in-Charge including excavation, royalty loading, unloading, transportation, stacking, filling, spreading, watering etc., as CUM 224.00 ₹ 810.00 ₹

57 Supplying and spraying of medecine/ pesticides like rogar/victor / forete etc. for garden. Per litre 20.00 ₹ 825.00 ₹

Supplying and ploughing of carpet lawn including excavation and ploughing of grass, watering etc. complete on the place as

directed by engineer incharge. (excluding the cost of water) including loading, un-loading and transportation.

Providing and Fixing Artificial Vertcial Grass for vertical gardening in required size and pattern with back support of Fibre cement

59 shieet of 8 mm thick at erected MS vertical steel strcuture made of Hollow steel tube section etc complete with all labour and SQM 208.32 ₹ 3,500.00 ₹

material as directed. (Excluding cost of Steel Structural)

Providing& fixing Sign Boards made out of 14 gauge aluminum sheet of req. size, bonded with coloured Retro-reflective sheeting

60 having pressure sensitive adhesive, screen printed with desire letters of approved size & colour on approved background & fixing SQM 44.65 ₹ 3,645.00 ₹

etc. as provided including designing the board as directed

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length

90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m to 4.00 m

apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including

necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed

tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight

gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

I / we am / are willing to carry out this work at ________% above / below (percentage should be written in figure & words). The tendered rates mentioned above amount of my/our tender are

Estimated amount put to tender Rs. ______________ Estimated amount put to tender Rs. ______________

Contractor EXECUTIVE ENGINEER (P)

DEENDAYAL PORT AUTHORITY