Annual Maintenance, Repairs and other emergent works of various water supply schemes under the jurisdiction PHE Sub Division Watlab of Jal Shakti PHE Division Sopore for the year 2026-27.

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 1 meter from cutting edge

In all kinds of soils

Ordinary rock

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.

In all kinds of soils

Ordinary rock

Hard Rock (Requiring Blasting )

Hard Rock (Blasting Prohibited)

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

In all kinds of soils

Ordinary rock

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earthlead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.

In all kinds of soils

Ordinary rock

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Beyond 30 cm girth upto and including 60 cm girth.

Beyond 60 cm girth upto and including 120 cm girth.

Beyond 120 cm girth upto and including 240 cm girth.

Above 240 cm girth

Providing & fixing upto floor five level precast cement concrete hollow blocks, including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete.

1:1½:3(1 cement :1½ coarse sand :3 graded stone aggregate 20 mmnominal size)

1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size)

Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement)

Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 (1 cement: 3 fine sand) including curing.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with:Cement mortar 1:6 (1 Cement : 6 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class kail

Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete

popular wood

First class Budloo/Fir wood

Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete.With 2nd class teak wood beading 62x19 mm

Providing and fixing specified board medium density exterior grade (Grade I) to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) :Flat pressed 3 layer particle board or graded wood particle board IS:3087 18 mm

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class Kail wood

Providing and fixing cupboard shutters 25mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade I Type II) having one side decorative lamination and other side a balancing lamination including second class teak wood lipping of 25mm widex12mm thick with necessary screws and bright finished stainless steel piano hinges complete as per directions of Engineer- in-charge

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-inchargeInternal work-exposed on wall with clamps at 1.00 meter spacing

PN-16 pipe, 16mm OD(SDR-7.4)

PN-16 pipe , 20mm OD(SDR-7.4)

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

PN-16 pipe , 40mm OD(SDR-7.4)

PN-10 pipe , 50mm OD(SDR-11)

Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.

PN-16 pipe, 16mm OD(SDR-7.4)

PN-16 pipe , 20mm OD(SDR-7.4)

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

External work including trenching, refilling etc

PN-16 pipe, 16mm OD(SDR-7.4)

PN-16 pipe , 20mm OD(SDR-7.4)

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

PN-10 pipe , 50mm OD(SDR-11)

PN-10 pipe , 50mm OD(SDR-11)

PN-10 pipe , 63mm OD(SDR-11)

PN-10 pipe , 75mm OD(SDR-11)

PN-10 pipe , 90mm OD(SDR-11)

PN-10 pipe , 110mm OD(SDR-11)

PN-10 pipe , 160mm OD(SDR-11)

Providing and fixing PPR Unions

PPR Union 20mm

PPR Union 25mm

PPR Union 32mm

PPR Union 40mm

PPR Union 50mm

PPR Union 63mm

PPR Union 75mm

Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work.

100 mm and 150 mm dia GI pipes

65 mm and 80 mm dia GI pipes

40 mm and 50 mm dia GI pipes

25 mm and 32 mm dia GI pipes

15 mm and 20 mm dia GI pipes

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge :

Above 40 mm nominal bore

15 - 40 mm nominal bore

Laying in position centrifugally cast (spun) iron S&S or flanged pipes (excluding cost of pipe)

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket.

100 mm dia pipes

125 mm dia pipes

150 mm dia pipes

200 mm dia pipes

250 mm dia pipes

300 mm dia pipes

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) light class

20 mm dia. nominal bore

25 mm dia. nominal bore

Providing and fixing imported wooden panelling 15mm thick over framming work of required pattern and design water proof strips of ply board for celiling/walling (imported wood/RAIT wood) incl ply wood framing.

Providing and applying touch-up wood polish on existing wooden surfaces, including sanding, filling minor cracks/imperfections, and applying 1-2 coats of approved synthetic enamel or wood polish, complete in all respects as directed by the Engineer-in-Charge.

Providing and fixing imported PVC panelling (8 to 10 mm Thick) of Approved make pattern including the base work of Gl channels with necessary screws and cornice at the edge with all carriages all complete as per the directions of incharge engineer at site.

Providing and fixing of wooden flooring of approved brand and fixing of 2 mm foam underneath the flooring with heatex solution including cost and carriage of all materials involved complete job.

Providing and Construction of 24'-0" deep Almirah made of plywood (18mm) with face of teak including cost of all hardware items of approved quality complete job.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

White washing with lime to give an even shade on Old Work (two or more coats)

Colour washing such as green blue or buff to give an even shade

New work (two or more coats) with a basecoat of white washing with lime.

New work (two or more coats) with basecoat of whiting

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre, two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of required shade: Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat.

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat: With ready mixed aluminum primer of approved brand and manufacture on resinous wood and ply wood

Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete. On steel work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete. On concrete work

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter

With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter

Flooring with marble stone of specified thickness as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including skirting in vertical, rubbing, polishing and curing complete with: Makrana White Second quality (16mm)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters: 80x1.25 mm M.S. laths with 1.25 mm thick top cover

80x1.25 mm M.S. laths with 1.25 mm thick top cover

80x1.20 mm M.S. laths with 1.20 mm thick top cover

80x0.90 mm M.S. laths with 0.90 mm thick top cov

Providing and fixing ball bearing for rolling shutters.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete

Upto 40mm Nominal Bore

Above 40mm Nominal Bore

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing RCC work manually by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-incharge

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate.

Carriage of material from divisional store up to dumping site of work, including loading, unloading and stacking etc. complete by Mechanical Transport

Cement & steel, G.I/C.I pipe avg. lead upto 01 Kms

Cement & steel, G.I/C.I pipe avg. lead upto 02 Kms

Cement & steel, G.I/C.I pipe avg. lead upto 03 Kms

Cement & steel, G.I/C.I pipe avg. lead upto 04 Kms

Cement & steel, G.I/C.I pipe avg. lead upto 05 Kms

Cement & steel, G.I/C.I pipe avg. lead beyond 5 Kms upto 10 Kms (per Km)

Cement & steel, G.I/C.I pipe avg. lead beyond 10 Kms upto 20 Kms (per Km)

Cement & steel, G.I/C.I pipe avg. lead beyond 20 Kms per additional Km

Sand & Agg. 20 mm avg. lead of upto 01 Kms

Sand & Agg. 20 mm avg. lead upto 02 Kms

Sand & Agg. 20 mm avg. lead upto 03 Kms

Sand & Agg. 20 mm avg. lead upto 04 Kms

Sand & Agg. 20 mm avg. lead upto 05 Kms

Sand & Agg. 20 mm avg. lead beyond 5 Kms upto 10 Kms (per Km)

Sand & Agg. 20 mm avg. lead beyond 10 Kms upto 20 Kms (per Km)

Sand & Agg. 20 mm avg. lead beyond 20 Kms per additional Km

40 mm Agg. avg. lead of upto 01 Km

40 mm Agg. avg. lead upto 2 Kms

40 mm Agg. avg. lead upto 3 Kms

40 mm Agg. avg. lead upto 4 Kms

40 mm Agg. avg. lead upto 5 Kms

40 mm Agg. avg. lead beyond 05 Kms upto 10 Kms (per Km)

40 mm Agg. avg. lead beyond 10 Kms upto 20 Kms (per Km)

40 mm Agg. avg. lead beyond 20 Kms per additional Km

Stone soiling avg. lead of upto 1 Km

Stone soiling avg. lead upto 2 Kms

Stone soiling avg. lead upto 3 Kms

Stone soiling avg. lead upto 4 Kms

Stone soiling avg. lead upto 5 Kms

Stone soiling avg. lead beyond 05 Kms upto 10 Kms (per Km)

Stone soiling avg. lead beyond 10 Kms upto 20 Kms (per Km)

Stone soiling avg. lead beyond 20 Kms per additional Km

Carriage of pipes from divisional store up to dumping site of work, including loading, unloading and stacking etc. complete by Mechanical Transport

100 mm and 125 mm dia DI/ GI pipes 1Km

100 mm and 125 mm dia DI/ GI pipes 2Km

100 mm and 125 mm dia DI/ GI pipes 3Km

100 mm and 125 mm dia DI/ GI pipes 4Km

100 mm and 125 mm dia DI/ GI pipes 5Km to 10 Km

100 mm and 125 mm dia DI/ GI pipes 10Km to 20 Km

100 mm and 125 mm dia DI/ GI pipes beyond 20 Km every additional lead

150 mm to 200 mm dia DI pipes 1 Km

150 mm to 200 mm dia DI pipes 2 Km

150 mm to 200 mm dia DI pipes 3 Km

150 mm to 200 mm dia DI pipes 4 Km

151 mm to 200 mm dia DI pipes 5 Km

150 mm to 200 mm dia DI pipes 5Km to 10Km

150 mm to 200 mm dia DI pipes 10Km to 20Km

150 mm to 200 mm dia DI pipes beyond 20Km for every additional lead

Centering and shuttering including strutting, propping etc, and removal of form for.

Foundations, footings, bases of columns etc for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Columns, pillars, piers, abutments, posts and struts.

Suspended floors, roofs, landings, balconies and access platforms.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Stairs (excluding landings) except spiral staircases.

Edges of slabs and breaks in floors and walls under 20cm wide

Extra for shuttering in circular work (20% of respective centring and strutting items)

Clearing snow (without frost) from roads manually.

Snow depth upto 150 mm

Snow depth over 150 mm but upto 250mm

Snow depth over 250 mm but upto 350mm

Snow depth over 350 mm but upto 450mm

Clearing snow (with frost) from roads, manually using picks and shovels; snow depth upto 150 mm

Clearing snow avalanche mixed with frost and compressed snow, including all types of equipments and safety to the workers while clearing the avalanches at head site

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) Quarry

Dry random rubble masonry with hard stone in foundation and plinth: With bond stone. (Nallah)

Renewing glass panes and re-fixing existing wooden fillets: Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

M.S. tube

E.R.W. tubes

G.I. pipes

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,

Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete.

Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4 mm aperture on both sides.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

In colour such as White, Ivory, Grey, Fume Red Brown

In all colours, shades, except White, Ivory, Fume Red Brown

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thick with zinc coating not less than 275 gram/m2

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.

1.00 mm thick with zinc coating not less than 275 gram/m2

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes

75 mm diametre

110 mm diametre

12mm Cement plaster finished with a floating coat of neat cement of mix:

1 : 3 ( 1 cement : 3 fine sand)

1 : 4 ( 1 cement : 4 fine sand)

Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Renewing glass panes, with wooden fillets wherever necessary :

Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)

Providing and Laying of Stone Soling Hand Packed and compacted manually including all carriages complete

Good Earth

Moorum

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge.Made of G.I. wire of dia 4 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc. if required will be paid separately).

50 mm dia

80 mm dia.

100 mm dia.

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately)

80 mm dia. nominal bore

100 mm dia. nominal bore

150 mm dia. nominal bore

200 mm dia. nominal bore

Providing and laying D.I. Specials of Class K-12 suitable for push-on jointing as per IS : 9523

Upto 600 mm dia.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. One coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Weed clearance

From lakes(using boats)

From canals(including extraction of roots)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) For fixed portion

Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) 22.1.1.2 Powder coated aluminum (minimum thickness of powder coated 50 microns)

Powder coated aluminum (minimum thickness of powder coated 50 microns)

Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) 22.1.2.2 Powder coated aluminum (minimum thickness of powder coated 50 microns)

Powder coated aluminum (minimum thickness of powder coated 50 microns)

Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge.

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic items)

With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)

With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

With float glass panes of 8 mm thickness (weight not less than 20.0 kg / sqm)

Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.

Dismantling of C.I. sluice valve including stacking of useful materials within a lead of 50 meters.

Upto 150 mm diameter.

Above 150 mm diameter.

Dismantling C.I. pipes manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes and lead at site within 50 meter lead as per direction of Engineerin-charge

Upto 150 mm diameter.

Above 150 mm diaupto 300 mm dia.

Cutting road and making good the same including supply of extra quantities of material i.e. crushed aggregate, moorum screening, red bajri and labour required.

Water bound macadam.

Bituminous portion

Labour for cutting C.I. pipe with steel saw.

80 mm diameter C.I. pipe

100 mm diameter C.I. pipe

125 mm diameter C.I. pipe

150 mm diameter C.I. pipe

200 mm diameter C.I. pipe

250 mm diameter C.I. pipe

Hand-packing stones in wire-crates; excluding cost of crates and stones

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead.

For thickness of tiles 10 mm to 25 mm

For thickness of tiles above 25 mm and upto 40 mm.

Supply of Pig Lead at site of work

Providing and fixing basin mixer of approved quality.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia

Providing and fixing CP Brass tapes of quality & make as approved by Engineer in charge. 15 mm nominal dia

Providing and fixing P.V.C low level flushing cistern with manually18.0 (Sanitary Installation) 240 CODE NO. DESCRIPTION UNIT RATE ₹ controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 litre capcity -white

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto/above plinth level

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 1st quality ceramic glazed floor/ wall tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Supply and Installation of acrylic Boards 5 mm thick with laser cut etc. complete Job

Dismantling of spindle / rod and check nuts of flanged type sluice valves by way of manufacturing of new spindle / rod made out of mild steel & new check nut made out of gun metal material. The job includes dismantling of sluice valve reassembling after fixing of spindle & check nut duly manufactures and threaded in workshop including cost of welding, packing, carriage to & fro upto the workshop and back to site of work (Complete job) from 80 mm dia sluice valve upto 300 mm dia sluice valve including cost of salvaged material.

Providing / fixing of M.S double collers/ arresting of leakages by way of welding including all sorts of carriages

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing / fixing of double collers, G.I./ M.S. for arresting of leakages by using led & spun yarn incld. earthwork excavation, refilling etc. including all sorts of carriages (length verying from 0.60 to 1 Mtr.)

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing and fixing including testing, commissioning & fabricating at site M.S pipe Specials Etc. & all sorts of carriages upto site of work, as per requirement at site complete job.

Providing and fixing of Electrical points (heating and lighting) incld. cost of wire switches, necessary MCB’s switch boards, ceiling roses reputed make ISI mark screws, casing / conduit materials of allsorts of carriage and labour charges required for the job.

Lighting points

Heating points

Supply/ fixing of pipe specials from open market, if not available in the Divisional stores of ISI marked standard make.

100 mm dia G.I Union

80 mm dia G.I Union

65 mm dia G.I. Union

50 mm dia G.I. Union

40 mm dia G.I. Union

25 mm dia G.I. Union

20 mm dia G.I. Union

80 mm dia G.I. Elbow

65 mm dia G.I. Elbow

50 mm dia G.I. Elbow

40 mm dia G.I. Elbow

25 mm dia G.I. Elbow

20 mm dia G.I. Elbow

80 mm dia G.I. Socket

65 mm dia G.I. Socket

50 mm dia G.I. Socket

40 mm dia G.I. Socket

25 mm dia G.I. Socket

20 mm dia G.I. Socket

80 mm dia G.I. Nipple upto 10"

65 mm dia G.I. Nipple upto 10"

50 mm dia G.I. Nipple upto 10"

40 mm dia G.I. Nipple upto 10"

25 mm dia G.I. Nipple upto 10"

20 mm dia G.I. Nipple upto 10"

15 mm dia G.I. Nipple upto 10"

25x25x20 mm dia G.I. Equal Tee

40x40x25 mm dia G.I. Equal Tee

50x50x40 mm dia G.I. Equal Tee

65x65x50 mm dia G.I. Equal Tee

80x80x65 mm dia G.I. Equal Tee

25x20 mm dia Socket/ Reducer

40x25 mm dia Socket/ Reducer

50x40 mm dia Socket/ Reducer

65x50 mm dia Socket/ Reducer

80x65 mm dia Socket/ Reducer

25x20 mm dia Elbow/ Reducer

40x25 mm dia Elbow/ Reducer

50x40 mm dia Elbow/ Reducer

65x50 mm dia Elbow/ Reducer

80x65 mm dia Elbow/ Reducer

100mm dia Elbow

100mm dia Equal Tee

100 mm dia G.I. Bend

80 mm dia G.I. Bend

65 mm dia G.I. Bend

50 mm dia G.I. Bend

40 mm dia G.I. Bend

Supply of Kerosene oil/Transformer oil including all carriages

Providing refreshment to officals/guests and the partcipants of the Indenpadnace Day , Republic day or other official Functions complette job including packing at venue with following Menu, incluidng serving charges/ carry bags

Water Bottle One litre

Water Bottle 500 ml

Water bollte 250 ml

Juice pac/ tin 100 ml to 180 ml of Standard Quality

Boiled Egg

Biscuit standard Quality of 50 g

Dal 50 g Pac

Banana

Butter Toastes each pair

Toastes without Butter each pair

Tea Sugar each Cup

Tea Namkeen each Cup

Re-threading of damaged pipe ends including carriage from site to workshop and back.

20 mm dia

25 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Dismentalling of backwash motors/ Alum motors/ bleaching motors of filtration plants by way of rewinding of core made out of copper metal fiber superior type of required thickness and guage. The job includes replacing of bearings, water seal, nuts, bolts, rubber washers and painting of instruments. The job also includes all sorts of carriage from site to work upto workshop to & fro including testing & commissioning of following capacity.

For 0.50 HP to 2.00 HP

For 3.00 HP to 5.00 HP

For 5.00 HP to 10.00 HP

Dismentalling of complete reduction gear unit of de-sludge bridges for repairs by way of providing & manufacuring of complete reduction gear with hub. The job includes costing of brass material, grinding & finishing of virme in order to make the new teeth, replacement of damaged oil seals by way of new one, replacemnet of ball bearings, pouring of required specific gravity ear oil in order to run the reduction gear in smooth order, refixing of same at the site of work incld. all sorts of carriage fro site of work upto workshop and back to site of work including testing & successful commissioning (complete job)

Overhauling voltage stabilizers installed at site. The job includes pouring / filling of transformer oil of required specified gravity, replacement of driven rotars (automatic), replacement of voltage meters, Amp meters, indicators, thimbles etc. complete job, making the unit complete functional for bearing of required load. The job also includes labour charges, cost of wiring, pin sockets and all sorts of carriages from site of work upto the workshop & back to actual site of work incld. installation at site & testing, successful commissioning complete job.

5 KV to 10 KV

11 KV to 20 KV

21 KV to 30 KV

Providing and fitting at site 3-phase, Voltage stabilizer 30 KVA of following ratings, oil emersed, of standard make and quality including accessories as required. The job includes making of connections with main panel board and service line. To be paid in fitted and finished form after testing on full load capacity, complete job.

Providing and fitting at site 3-phase, Voltage stabilizer 25 KVA of following ratings, oil emersed, of standard make and quality including accessories as required. The job includes making of connections with main panel board and service line. To be paid in fitted and finished form after testing on full load capacity, complete job.

Supply and filling of filter media from approved source - Gravel (Graded gravel - size ranging from 2.0mm to 40.00 mm) in filter beds. Including all carriages, complete job

Supply and filling of filter media from approved source - Sand (Coarse filter sand - in filter beds. Including all carriages, complete job

Bore Packing: All the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout - GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pipe and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent.

Desilting of various structures incld. Disposal of desilted material from site premises with all carriages lead & lifts etc. The job also includes, washing and cleaning of walls, beds, drains and floor etc with bleaching powder solution complete job.

Using buckets, ropes etc. Manually

Through washout by Mix silt with water

Replacement / supply of PVC gate valves for bleaching / alum tanks/ Foot valves and PVC pipes of ISI marked standard make

20 mm dia Gate valve

25 mm dia Gate valve

32 mm dia Gate valve

40 mm dia Gate valve

50 mm dia Gate valve

20 mm dia PVC pipe (B-class)

25 mm dia PVC pipe (B-class)

32 mm dia PVC pipe (B-class)

40 mm dia PVC pipe (B-class)

50 mm dia PVC pipe (B-class)

80 mm dia PVC pipe (B-class)

100 mm dia PVC pipe (B-class)

Replacement of old damaged G.I. Gate valves by Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) and providing of check certificate from the standard manufacturer.

25 mm nominal bore

20 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Supply of CFL Bulbs for filtration plant sites etc.

Welding, including transportation of plant at site etc. complete

By gas plant

By electric plant

Plugging of leakages of pipes at spots with welding around only by electric welding plant including all carriages upto site of work excluding cost of Earthwork and refilling including hire charges of welding plant.

65 mm/80mm dia pipe

100 mm /125 mm dia pipe

150 mm / 200 mm dia pipe

Hire charges for welding plant for necessary repairs of pipe network/structures etc as per requirement including C/O operator, Genrator, welding rods, wiring and carriage of man and machinary complete in all respects as per requirement at site but excluding additional materials like collar, pipe specials, steel section etc.

Providing / fixing of M.S. step collers from 100 mm to 450 mm dia including all sorts of carriages, complete

Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). 16.67.1 Overhead informatory road signage.

Supply and fixing of Inaugration stone of Marble/Granite with custom carved letters complete including Making of Foundation made out of Brick work including 15mm thick Plater in 1:4 Mix including all sorts of carriages wherever required

Providing and fixing of printed PVC type flex banners as per requirement complete job

Without the supporting frame of steel rolled hollow Sq. bars

With the supporting frame of steel rolled hollow Sq. bars

With the supporting frame of steel rolled hollow Sq. bars and cardboard backing

Supply of unskilled labours

Supply of skilled labour

Supply of Carpenter 2nd class

Supply of Mason 2nd class

Providing / Fixed of GI barbed wire weight 9.3 Kg per 100m (min) between two ports fitted and fixed with GI staples on wooden plugs or GI binding wire tied to 6mm bar nibs, Complete Job

Repairs to barbed wire fencing, complete job

Providing and Fixing of M.C.C.B.of ISI marked standard make the job includes dismantling of damaged/non functional Amp. M.C.C.B. and fixing of new one including all sorts carriage from source to workshop including carriages of salvaged material from filtration plant upto Divisional Stores including testing, installing and commissioning complete job

03 Pole 200 Amp.

03 Pole 100 Amp.

04 Pole 100 Amp.

02 Pole 32 Amp.

03 Pole 32 Amp.

04 Pole 32 Amp.

63 Amp 04 pole change over

3.5 core cable 50 mm thick

Providing and Fixing of 5-10 H.P. Starter of of ISI marked standard Make, the job includes dismantling of damaged /non functional starter and fixing of new one incl. all sorts of carriages from source to workshop including carriages of salvaged materials from filtration plant upto Divisional Stores, including testing, installing and commissioning complete job.

Providing and Fixing of running V-Belt of groove type for air blower, the job includes dismantling damages ones and fixing of new ones incl. successful testing, commissioning. All types of carriage complete

Providing fixing & commissioning of LED Flood Lights of 50 Watts with stand including all accessories required at site complete job inclusive all carriages.

Providing fixing & commissioning of LED Flood Lights of with stand including all accessories required at site complete job inclusive all carriages.

Supply of LED lights of different Wattage of approved m ake ISI marked complete in all respects

Providing fixing & commissioning of 10/12 mm thick Flanges in pairs including welding, cutting of threaded portion, washers including cost of Flanges with Nuts and Bolts including making joint leak proof including all sorts of labours whatsoever required

250mm dia

200mm dia

150mm dia

100mm dia

80mm dia

65mm dia

Restoration of damaged pipes due to frost / frozen including earth works excavation /dismantling /refilling / making good the same complete job in all respects. Upto 20mm to 100mm dia (by using blue lamp including cost of K.oil)

P/F of Air Releasing Valves (single acting) including cutting of bore hole , welding of the pedestal rod and providing laying of cement concrete 1:3:6 mix with shuttering box PGI 9”X9”x12” around the pedestal rod with all carriages and head load upto actual site of work

25mm dia Air Valve

20mm dia Air Valve

Laying & fixing of HDPE Pipes complete excluding earth work, but including all carriages upto site of work

25mm dia

32mm dia

40mm dia

50mm dia

Fixing charges of Sluice Valves including Testing, Commissioning and carriages from divisional store to actual site of work including dismantling of old (in case of replacement) and carriage of same to divisional store, Complete job

200 mm dia

150 mm dia

100mm dia

80mm dia

50mm dia

Engagement of JCB including haltage charges and one side POL Charges

Removal of dead animals from canals including disposal within 50 mts complete job

By Mechanical means

By Mannual means

Constructing muthu bunds, comprising boulders and wood bushes in alternate layers; including working in water situations

Supplying and Laying of polythene sheets (Black) at off take points during lean dscharge / Freezing

Opening out old wire crates those and re-binding after filling.

Filling empty cement bags with sand/ earth including cost of bags and earth / sand (Earth or sand to be locally excavated) including all sorts of carriages upto actual site of work

Silt clearance from canals Inclusive of initial lead of 50 mts and all lift Comp Job

Removing, washing of old filter media including washing of filter beds and laying of same in position complete job.

Supplying & fixing as per site requirement of Nylon rope on 10 mm dia of Standartd make including all carriages comp job

Hire charges of boat including charges of operator and other allied items required, complete.

Boat(Capacity 20 cum)

Providing / fixing of slip ring complete set with cliffs, bushes all accessories for clarifloculator bridge. The job includes disassembling of the damaged slipring returned back to store and fixing of new one, including all carriages.

Supply of wire crates including all types of carriages upto site of work.

Supply of stones including all types of carriages upto site of work.

Providing coloured Photographs as per requirement/ works executed at various places on photo paper of size 4"X6"

Repair of Computer Desktops/Laptops, Inktank Printers, copiers, cables etc. complete

Providing Flower Bookies during VIP Visits, Inaugrations etc.

Documentation of various offical documents/DPRs including

Paper Ream

Spiral Binding

Thermal Binding

Supply of Spun yarn

P/F of PPR pipe, including all pipe fitting, carriages upto Site of work complete in all respects

Providing of PPR Gate valves/ Ball valves including all necessary accessories as per requirement at site complete

25 mm Gate valve/ Ball valve

32 mm Gate Valve/ Ball valve

40 mm Gate valve/ Ball valve

Supply of Nallah Muck including laying of same manually/ mechanically including all sorts of carriage complete

Supply of stone dust including laying of same manually including all sorts of carriages complete

Hire charges of Sumo for various anouncements regarding the water usage/registration/awarances etc including the mic, speaker, driver, fuel etc complete as per requirements and minimun 50 kms of distance to be covered.

Supply of coloured banners using PVC/Vinyle roll including writing of description as per directions complete in all respects.

Lettering with black Japan paint of approved brand and manufacture.

Providing CI/DI Sluice valve including cost of nuts, bolts, rubber insulations etc. of ISI marked standard make all carriages upto site of works, complete and providing of check certificate from the standard manufacturer

50 mm dia. Class 1

65 mm dia. Class 1

80 mm dia. Class 1

100 mm dia. Class 1

125 mm dia. Class 1

150 mm dia. Class 1

200 mm dia. Class 1

250 mm dia. Class 1

Fabrication of GI bends of required angle/size, Tees, tail pices etc at site using welding job including cutting of pipes, fixing of flunges, nuts, bolts, washers etc for Washout system. The job includes carriage of man , machinary, carriage of pipe material from departmental store upto site of work complete in all respects. Cost of flanges will be paid separately

80mm dia

100mm dia

150mm dia

Fabrication of M.S Glands/pipe specials of required size, Tees, tail pices etc at site as per ground profile using welding job including cutting of pipes, fixing of flunges, nuts, bolts, washers etc for Washout system. The job includes cost of M.S pipe, flanges, nuts , bolts glands, R.I cloth complete job

Providing and fixing of Mild steel mesh with 2.50 to 3.50mm thick mesh fixed in angle iron frame 45x45x6mm including applying a priming coat of approved steel primer all complete to cover varios SSFP'S, gratings, at head sites etc as per requirement.

Providing of blue lamps including all sorts of carriages complete

1 ltr capacity

0.75 ltr capacity

Providing/ fixing of Rubber Gaskets

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

Providing/ fixing of Rubber Washers

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

Supply of cast iron general purpose pipe wrenches of Stilson type as per IS: 4003(Part-I) - 1978 inclusive of all taxes and carriages.

Size 10 inch, length 250 mm suitable for pipe dia upto 32 mm

Size 300 mm, Length 12.5 inch upto 40 mm dia

Size 350 mm, Length 14 inch upto 50 mm

Size 450 mm, Length 18 inch upto 65 mm

Size 600 mm, Length 24 inch upto 80 mm

Hire and installation charges of Shamyana’s of good quality/shape/colour/hygiene (as per the directions of Engineer In-charge) for VIP’s, Guests, Officers, School Children etc with all leads, lifts, handing, rehandling and carriage upto site and lifting back after conclusion of ceremony.

Hire charges for supply of furnishing/furniture items of good quality/shape/colour/hygiene (as per the directions of Engineer In-charge) of required size with all leads, lifts and carriage including fixing of the same in arranged manner as will be directed at site all complete

VIP Chairs

P.V.C Chairs (heavy duty)

Druggets (12’x12’)

Carpets (12’x12’)

Red Runners of required width

Hire and installation charges of stage top/canopy of size 32’x24’ with all leads, lifts, handling, rehandling and carriages complete (as per the directions of Engineer incharge). Including crewel ceiling and fixtures with necessary decoration as per instructions at site (all complete.

Excavating holes in all classifications of soil of required size and depth for erecting of barricading post with ramming watering and disposal of surplus excavated soil beyond site premises or as will be directed at three rows with all leads, lifts , carriage, handling, rehandling and removing of the same after conclusion of the ceremony all complete as per the directions of Engineer Incharge.

Hire and installation charges of Pindals having size (50’-0’x150’-0”) for four days fixed with G.I tube with water proofing top and sides white house ornamental celling with crewel lining of required size for VIP’s, civil and police officers of district administration distinguished guests, panches and surpanches and other designates to grace the occasion (it should be of good quality, shape , colour, hygiene as per the Directions of Engineer In-charge)

Supply and fixing of Banners of required sizes with required letter writing as directed size (3’x6’) complete

Hire Charges Of loudSpeakers for necessary announcements