Renovation To EI work at Taluka Seva Sadan Morbi, Dist- Morbi

Name of Work:- Renovation To EI work at Taluka Seva Sadan Morbi, Dist- Morbi.

Sr. Quantities Estimated Rate

No. estimated but

may be more or Description of Item.

In Figures In Words according

1 1055 pt Replacing old & U/s By Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 410.06 Rupees Four

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi Hundred Ten And

strand copper wires up to 10 mtr length , in below type of pipe erected with 6A Modular Paise Six Only

type switch / bell push & accessories and earth continuity of following type, erected on

PVC / Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(j) in existing pipe erected concealed in wall/ceiling complete Cat. III

(Old- 960, New-95 )

2 448 Pt Replacing Old and U/s Burnt Wiring By Point wiring for FAN with 2-1.5 sq.mm & earth 556.51 Rupees Five

wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated Hundred Fifty Six

multi strand copper wires up to 10 mtr length, in below type of pipe erected with 6A And Paise Fifty

Modular type switch and hum free EME step type electronic fan regulator mounted and One Only

accessories with earth continuity of following type erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed.

(j) in existing pipe erected concealed in wall/ceiling complete Cat. III

(Old- 448, New- 0 )

3 65 Pt Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth wire 120.19 Rupees One

of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi Hundred Twenty

strand copper wires, in below type of pipe to be erected complete with earth continuity And Paise

and necessary connection with primary light with accessories erected on Metal / PVC / Nineteen Only

wooden box covered with 3 mm thick PC(Polycarbonate) / Acrylic sheet for open /

concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.

(j) in existing pipe erected concealed in wall/ceiling complete

4 94 Pt. Replacing old & U/s By Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 425.21 Rupees Four

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper Hundred Twenty

wires up to 10 mtr length, in below type of pipe erected complete with Modular type Five And Paise

switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate Twenty One Only

front plate modules erected on / in wall / ceiling as per pipe erected with following type of

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb

(j) in existing pipe erected concealed in wall/ceiling complete Cat. III

(Old- 80, New-14 )

5 152 Pt. Replacing old & U/s By Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 567.62 Rupees Five

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper Hundred Sixty

wires up to 10 mtr length, in below type of pipe erected complete with Modular type Seven And Paise

switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate Sixty Two Only

front plate modules erected on / in wall / ceiling as per pipe erected with following type of

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board

(j) in existing pipe erected concealed in wall/ceiling complete Cat. III

(Old- 145, New- 7 )

6 217 Pt Replacing old and U/s By Point wiring for on board Looped Plug with 6A Modular type 257.55 Rupees Two

switch & 5 pin socket erected on PVC / Metallic/Wooden box, single mounting base Hundred Fifty

frame covered with textured / metallic/white front plate modules erected on / in wall / Seven And Paise

ceiling with following type accessories Cat. III Fifty Five Only

(Old- 207, New-10 )

7 314 Ea Providing following type of Modular Type Accessories mounted with PVC / 160.59 Rupees One

metallic/Wooden box, single mounting base frame covered with textured / metallic/white Hundred Sixty

front plate , modules erected with necessary connections as per site situation directed by And Paise Fifty

Engineer In charge. Nine Only

(8) Computer RJ-45 socket Cat.III

8 6250 Mtr Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size 24.24 Rupees Twenty

complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Four And Paise

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in Twenty Four Only

approved manner as directed

9 1150 Mtr (b) 25 mm 33.33 Rupees Thirty

Three And Paise

Thirty Three Only

10 250 Mtr Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, 17.17 Rupees Seventeen

PVC bushes, Check-nuts etc. complete of following sizes. And Paise

(1) 20 mm Seventeen Only

11 5467 Mtr Replacing old & U/s By Providing and erecting Mains with 1.1 KV grade FRLS PVC 62.62 Rupees Sixty Two

insulated ISI marked stranded Copper conductor wire in following type of pipe to be And Paise Sixty

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS Two Only

PVC insulated stranded wire of green colour for earth continuity of following size

(E) in existing pipe ,(b) 2 wire 2.5 sq. mm

12 902 Mtr Replacing old & U/s By providing and erecting Mains with 1.1 KV grade FRLS PVC 211.09 Rupees Two

insulated ISI marked stranded Copper conductor wire in following type of pipe to be Hundred Eleven

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated And Paise Nine

stranded wire of green colour for earth continuity of following size. Only

(E) in existing pipe.

(c) 2 wire 10 sq. mm

(use earth wire of 4 sq.mm )

(Old- 840, New- 62 )

13 185 Mtr Replacing old & U/s By providing and erecting Mains with 1.1 KV grade FRLS PVC 398.95 Rupees Three

insulated ISI marked stranded Copper conductor wire in following type of pipe to be Hundred Ninety

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated Eight And Paise

stranded wire of green colour for earth continuity of following size. Ninety Five Only

(E) in existing pipe.

(i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

(Old- 160, New- 25)

14 4 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 56.56 Rupees Fifty Six

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - And Paise Fifty

227 erected in existing pipe of following size (Specifically for control panel, relays, Six Only

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required.

(e) One wire 6.00 sq. mm

15 36 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 91.91 Rupees Ninety

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - One And Paise

227 erected in existing pipe of following size (Specifically for control panel, relays, Ninety One Only

power switchgears, motor starters & control wiring) with required size of copper lugs,

nuts and bolts if required.

(f) One wire 10.00 sq. mm

16 12 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 300.98 Rupees Three

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - Hundred And

227 erected in existing pipe of following size (Specifically for control panel, relays, Paise Ninety Eight

power switchgears, motor starters & control wiring) with required size of copper lugs, Only

nuts and bolts if required.

(i) One wire 35.00 sq. mm

17 18 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 1178.67 Rupees One

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - Thousand One

227 erected in existing pipe of following size (Specifically for control panel, relays, Hundred Seventy

power switchgears, motor starters & control wiring) with required size of copper lugs, Eight And Paise

Sixty Seven Only

nuts and bolts if required.

(m) One wire 120.00 sq. mm

18 6 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 1461.47 Rupees One

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - Thousand Four

227 erected in existing pipe of following size (Specifically for control panel, relays, Hundred Sixty

power switchgears, motor starters & control wiring) with required size of copper lugs, One And Paise

Forty Seven Only

nuts and bolts if required.

(n) One wire 150.00 sq. mm

19 80 Mtr Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI 22.22 Rupees Twenty

marked copper wires of following size to be erected as directed. Two And Paise

(c) 1.00 Sq.mm 2 core round/ flat PVC sheathed Twenty Two Only

20 172 Mtr Replacing old and U/s Wire By Supplying and erecting Flexible PVC insulated multi 46.46 Rupees Forty Six

strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as And Paise Forty

directed. Six Only

(e) 1.50 Sq.mm 3 core round PVC sheathed

(Old- 92, New- 80 )

21 314 Ea Replacing old and u/s by Providing & erecting Switch board for Computer or electric 1133.22 Rupees One

apparatus consisting of following modular type accessories mounted with PVC / Thousand One

Metallic concealed/open box with single mounting base frame covered with Hundred Thirty

textured/metallic /white front plate,modules erected with necessary connections as Three And Paise

Twenty Two Only

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories. Cat. III

(Old- 305, New-9 )

22 63 Ea Decorative call bell Ting-tong box type 250 volts complete erected 71.71 Rupees Seventy

Seventy One Only

23 871 Ea Replacing old and u/s by Supplying and erecting LED indoor fittings with LEDs of 535.30 Rupees Five

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat Hundred Thirty

sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast Five And Paise

powder coated and high U.V. & corrosion resistance with diffuser with company Thirty Only

mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet , Cat-lll

(Old- 685, New-186 )

24 130 Ea Replacing old and u/s by Supplying and erecting LED indoor fittings with LEDs of 589.84 Rupees Five

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat Hundred Eighty

sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure Nine And Paise

die cast powder coated and high U.V. & corrosion resistance with diffuser housed in Eighty Four Only

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for

spring loaded mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV , Cat-lll

(Old- 104, New-26 )

25 42 Ea. Replacing old and u/s by Supplying and erecting led lamps with following wattage 112.11 Rupees One

capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-surge Hundred Twelve

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, And Paise Eleven

(A) LED Lamps integral type, with PC diffuser suitable LAMP holder

(ii) 5 to 8 watts ,Cat-III (Old- 26, New-16 )

26 20 Ea Replacing Old and U/s Light By Supplying and erecting LED street light / Flood light 4997.48 Rupees Four

fittings with High power White LEDs wattage of 3 Watt and above assembled on single Thousand Nine

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast Hundred Ninety

aluminum housing with smooth finish powder coated and heat sink extruded aluminium Seven And Paise

Forty Eight Only

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD <

%, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt

. LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC

line supply with over-voltage

(ii) above 48 to 60 Watts Cat-lll

(Old-10, New-10 )

27 6 Ea Replacing Old and U/s Light By Supplying and erecting LED street light / Flood light 8453.70 Rupees Eight

fittings with High power White LEDs wattage of 3 Watt and above assembled on single Thousand Four

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast Hundred Fifty

aluminum housing with smooth finish powder coated and heat sink extruded aluminium Three And Paise

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD <

%, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt

. LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC

line supply with over-voltage protection.

(v) above 120 to 160 watts Cat-lll

(Old- 6, New- 0 )

28 2 Ea Replacing old and u/s 63A ICTP By providing and erecting Approved make Four pole 6173.12 Rupees Six

moulded case circuit breaker having breaking capacity ICU of 25 KA. at 415 V,having Thousand One

normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release suitable Hundred Seventy

to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & Three And Paise

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

29 3 Ea Replacing old and U/s MCCB BY Providing and erecting Approved make Four pole 20946.39 Rupees Twenty

moulded case circuit breaker having breaking capacity ICU of 35 KA. and above at 415 Thousand Nine

V . having normal current rating 250A. with variable thermal & magnetic release Hundred Forty Six

suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned And Paise Thirty

copper & complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

(Old-1, New- 2)

30 1 Ea Providing and erecting Approved make Four pole moulded case circuit breaker having 25228.79 Rupees Twenty

breaking capacity ICU of 50 KA and above at 415 V having Normal current rating Five Thousand

400A. with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. Two Hundred

With all internal connections, spreader tinned copper & complete erected in existing 16 Twenty Eight And

Paise Seventy Nine

G.M.S. housing.

ICS=100% of ICU only Cat III

31 1 Ea Supplying & erecting approved make Four Pole 415V change over switch interior for 2611.86 Rupees Two

panel mounting with operating mechanism A.C.23 duty confirming to IS for Thousand Six

(A)32-40A Cat-lll Hundred Eleven

And Paise Eighty

32 0.6 Rn.Mt Replacing old and U/s 100A Busbar By Supplying and erecting triple pole & neutral 1961.42 Rupees One

r 440V / 500V panel mounting Copper Busbars with four equal Nos. of electrolyte bus Thousand Nine

having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section Hundred Sixty

area) duly wrapped with colour insulating tape for phase sequence of following current One And Paise

carrying capacity, erected with necessary bus bar supports /insulators, main cable socket

to each bar, erected in existing cubical panel with necessary connections.

(A) Suitable for 100 Amp. Capacity

(old- 0.4, New- 0.2)

33 0.6 Rn.Mt Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper 7319.47 Rupees Seven

r Busbars with four equal Nos. of electrolyte bus having current density not more than 1.6 Thousand Three

Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating Hundred Nineteen

tape for phase sequence of following current carrying capacity, erected with necessary And Paise Forty

bus bar supports /insulators, main cable socket to each bar, erected in existing cubical

panel with necessary connections.

(D) Suitable for 400 Amp. capacity

34 36 Ea providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and 270.68 Rupees Two

having breaking capacity 10 KA to be erected in existing box. confirming to IS Hundred Seventy

8828/1996 with ISI Mark ,Cat-III And Paise Sixty

35 388 Ea Replacing old and u/s by providing and erecting Miniature circuit breaker single pole 6A 112.11 Rupees One

to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to Hundred Twelve

be erected in existing box. confirming to IS 8828/1996 with ISI Mark , Cat.III (old- And Paise Eleven

360,New- 28) Only

36 61 Ea Replacing old and u/s by Providing & erecting 240 V MCB double pole switch for motor 330.27 Rupees Three

& inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in Hundred Thirty

existing box having following capacity . (B) 40 Amp. Cat.III (old-55,New- 6) And Paise Twenty

37 2 Ea Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 638.32 Rupees Six

10KA breaking capacity & confirms to IS :8828 in existing box having following Hundred Thirty

capacity Eight And Paise

(b)40 Amp. Cat.III Thirty Two Only

38 11 Ea. Replacing old and u/s ICTP Swich By Providing & erecting 415 V MCB Four Pole for 668.62 Rupees Six

Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS Hundred Sixty

:8828 in existing box having following capacity Eight And Paise

(b)40 Amp. Cat.III (old-8,New-3) Sixty Two Only

39 38 Ea. Providing and erecting Sheet Steel powder coated MCB distribution board - flush / 1492.78 Rupees One

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS Thousand Four

8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The Hundred Ninety

DBs should be used of same company of MCB to be used) suitable for Two And Paise

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

(Old- 38, New- 0 )

40 7 Ea Replacing old and u/s by Providing and erecting Sheet Steel powder coated MCB 3412.79 Rupees Three

distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and Thousand Four

DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house Hundred Twelve

appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be And Paise Seventy

used) suitable for,

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation

(b) sheet steel double door,

(Old- 4, New- 3 )

41 65 Ea providing and erecting Approved make RCCBs conforming to IS: 12640 and having 2235.13 Rupees Two

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for Thousand Two

operation on single phase 240 V,50Hz. having characteristic of quick action & tripping Hundred Thirty

with all advance feature & do not incorporate any electronic component. for following Five And Paise

Max. rating erected as directed

(ii) 40Amps. DP Cat. III

42 2 Ea Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing 4591.46 Rupees Four

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion Thousand Five

free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron Hundred Ninety

galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection One And Paise

terminal dia of 12mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM has to submit test certificate) &

having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:-

/ meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test report must be submitted.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

43 18 Kg. Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 77.77 Rupees Seventy

Seven And Paise

44 2 Sq.Mtr Replacing old Wooden Panel by Providing & erecting weather proof, dust & vermin 10468.65 Rupees Ten

proof, floor mounted front operated indoor type cubical panel board necessary IP-42 and Thousand Four

above protection as per approval from engineer incharge made from 14 SWG thick CRC Hundred Sixty

M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions Eight And Paise

Sixty Five Only

with necessary accesories , supporting angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire /

copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates,

sufficient nos. of hinged doors, handles with locking arrangement and rubber

gasket,heavy duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following approved manufacturers with

following size.

(A) locally fabricated panel board

(i) with 350 mm depth

45 120 Kg Providing , erecting , fabricating the M.S. structure as per requirement on site 77.77 Rupees Seventy

incorporating proper size of M.S. angles,square,round, flats, bars, channels, sections Seven And Paise

complete with cutting, welding, grinding & finishing duly painted with one coat of red Seventy Seven

oxide with erection on site as per direction of engineer in charge with necessary grouting, Only

cementing, plastering & finishing complete.

46 15 Mtr Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium 1168.57 Rupees One

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / Thousand One

pipe of following size of cables Hundred Sixty

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core) Eight And Paise

Fifty Seven Only

47 480 Mtr Replacing old and Faulty Cable By Providing and erecting XLPE (IS:7098)(I)-88 ISI 126.25 Rupees One

armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall Hundred Twenty

with necessary clamps or in existing trench / pipe of following size of cables Six And Paise

(B) 4 core 6 Sq. mm Twenty Five Only

(Old- 290, New- 190)

48 410 Mtr Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth 74.74 Rupees Seventy

for laying any size of cable or locating the fault all over the run and back filling the same Four And Paise

and making the surface as normal ground. Seventy Four Only

49 410 Mtr Providing & laying approved make Double walled corrugated pipes (DWC) of 62.62 Rupees Sixty Two

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same And Paise Sixty

material at required depth in existing trench for laying of cable. below ground / road Two Only

surface for enclosing cable

(A)50 mm outer dia

50 2 Ea Providing and, fixing heavy duty flange type brass double compression type cable gland 247.45 Rupees Two

with rubber ring for PVC insulated armoured cable complete with out going tails, Hundred Forty

insulating tape etc for following size of cables. Seven And Paise

(H) 3 & 1/2 core 240 Sq. mm Forty Five Only

51 8 Ea Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 6.06 Rupees Six And

following size evenly crimped with high pressure tool & connected to switchgear Paise Six Only

terminals with brass/cadmium plated nut bolts in an approved manner.

52 4 Ea Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 45.45 Rupees Forty Five

following size evenly crimped with high pressure tool & connected to switchgear And Paise Forty

terminals with brass/cadmium plated nut bolts in an approved manner. Five Only

53 12 Ea Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 85.85 Rupees Eighty

following size evenly crimped with high pressure tool & connected to switchgear Five And Paise

terminals with brass/cadmium plated nut bolts in an approved manner. Eighty Five Only

54 448 Ea Replacing old and U/s Ceiling Fan By Providing & erecting Approved make Power 1948.29 Rupees One

Saving 50 Watt Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt Thousand Nine

A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium blades with , Hundred Forty

canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Engineer in Eight And Paise

Twenty Nine Only

(Old- 436, New- 12 )

55 448 Ea. Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 18.18 Rupees Eighteen

56 14 Ea Replacing old and U/s Exaust Fan By Supplying & erecting single phase approved make 2740.13 Rupees Two

industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable Thousand Seven

for medium duty having following dia size and maximum speed in RPM. Hundred Forty

[B] 380 mm dia 900 RPM.Cat.II And Paise

(old -8, New-6 )

57 8 Ea Supplying and erecting approved make oscillating type bracket fan A.C. 23OV. 50cy/s 2534.09 Rupees Two

400/450 mm sweep wall mounted with height adjustment and rotary tilting device Thousand Five

complete with guard, flexible Core plug top complete erected with lead wires as directed. Hundred Thirty

Cat.II Four And Paise

58 10 Ea Replacing old and U/s By Supply of approved make FRP Pole having following 11719.03 Rupees Eleven

specifications: FRP Light Pole made by CNC filament winding machine using thermoset Thousand Seven

resin polyester/epoxy resin system) having minimum 62% glass content. The pole should Hundred Nineteen

be in one piece and tapered round in shape, having smooth finish and should be totally And Paise Three

free from corrosion as well as non conductive & shock proof Pole should be provided

with FRP Anchor Base and it should be heavy duty, or MS Material duly painted with

Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and

pigmented. A highly weather resistant polyurethane coating shall be applied to the pole

after applying suitable primer system that ensures proper adhesion of the paint. Minimum

coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more

than 10% of the length of pole for the given load“ Pole should be generally made as per

the dimensional data, performance criteria and some interchangeability features of poles

as per standard ANSI C 136.20 latest version or ASTM D 4923/01 including cable

termination box with necessary accessories . The size of pole and type of installation with

foundation as per manufacturer details and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[F] Overall length of 5 Mtr. Average Thickness: 7.5mm

OD Dia A/F 89/158 mm ± 2mm approx. approx. Weight of Pole 25 kg approx. (Without

Base) Anchor Base (Size 250X250 & 16mm th.)

(Old-10, New-0 )

59 5 Ea Supply of approved make FRP Pole having following specifications: FRP Light Pole 12425.02 Rupees Twelve

made by CNC filament winding machine using thermoset resin polyester/epoxy resin Thousand Four

system) having minimum 62% glass content. The pole should be in one piece and tapered Hundred Twenty

round in shape, having smooth finish and should be totally free from corrosion as well as Five And Paise

non conductive & shock proof Pole should be provided with FRP Anchor Base and it

should be heavy duty, or MS Material duly painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and

pigmented. A highly weather resistant polyurethane coating shall be applied to the pole

after applying suitable primer system that ensures proper adhesion of the paint. Minimum

coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more

than 10% of the length of pole for the given load“ Pole should be generally made as per

the dimensional data, performance criteria and some interchangeability features of poles

as per standard ANSI C 136.20 latest version or ASTM D 4923/01 including cable

termination box with necessary accessories . The size of pole and type of installation with

foundation as per manufacturer details and site requirement are as below .

(2) Suitable for base plate mounting Double arm Bracket.

[A] Overall length of 5 Mtr. Average Thickness: 8mm.

Top/ Bottom OD Dia A/F 114/163mm ± 2mm approx.approx. Weight of Pole 31 kg

approx. (Without Base) Anchor Base (Size 300X300 &18mm th.)

60 10 Ea Providing Aluminium arm bracket of having 2 sets of suitable SS304 hardware for 2234.12 Rupees Two

fixing the brackets & spread of 1.2 Mtr (Suitable for 89 to 114 mm pole top dia) Thousand Two

(A) Single arm bracket Hundred Thirty

61 5 Ea Providing Aluminium arm bracket of having 2 sets of suitable SS304 hardware for 3450.16 Rupees Three

fixing the brackets & spread of 1.2 Mtr (Suitable for 89 to 114 mm pole top dia) Thousand Four

(B) Double arm bracket And Paise Sixteen

62 16 Ea Replacing old and Damaged Sintex Box By Supplying & erecting approved make SMC 297.95 Rupees Two

press moulded composite FRP. loop-in, loop-out approx. 2mm thick box complete with Hundred Ninety

Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as Seven And Paise

per requirement having locking arrangements with mounting clamp with nuts, bolts & Ninety Five Only

washers suitable for erection on pole with cable clamps& earth bolt of following size of

(D) 140mm x 140mm x 100mm [deep]

Old- 16, New- 0)

63 1 Ea Supplying & erecting approved make Digital time switch having lithium cell 6 years 3168.37 Rupees Three

operative and operate battery backup 1 channel day clock with 14 memory programme, Thousand One

suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup Hundred Sixty

time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Eight And Paise

Thirty Seven Only

Programming switches & housed in fire proof thermoplastic enclosure & transparent

cover erected as required with necessary connection erected as directed.

64 1 Ea Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per 2782.55 Rupees Two

direction Cat III Thousand Seven

(D) 4 pole 440V 40 Amp. Hundred Eighty

Fifty Five Only

65 1 No. Supplying & erecting Mixing Console having channels, Audio mixer with. Echo facility 12411.89 Rupees Twelve

for live performance, Auditorium & stadiums, having following features & facilities. Thousand Four

[[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Hundred Eleven

(a)input Channels :- Each channel has separate 6.25mm size balanced phone jack And Paise Eighty

for mike & line for balanced & unbalanced signals. (b)Individual gain control for sating

optimum level for minimum noise. (c)BASS, MID & TREBLE ‘ controls Separately

for each input channel. (d)ECHO control for each channel (e)PAN control for echo

channel for left or right output (f) AUX Control : To control , level of the channel in

final mix to AUX sound output (g)Channel ON/OFF switch (h)ECHO Section :- ECHO,

reverb & Chorus effect can be added to all input channel by different setting of Delay,

Reverb & Level control. (i)Tape section (j)Aux. send & return For sending Pre-feeder

output of channel for monitoring or adding a special effect unit. (k)Mono / Stereo output

controls (L)Master faders to control over left & right output (m) Head phone output for

monitoring purpose.

Technical specification

(a)Power Requirement -AC220-24OV 50 Hz DC 24 Volts (b)MIC Output

Impedance/gain -2 K Ohms/ 62 dB (c)Line Output Balance/42 dB —- 20 K

ohms (d) Impedance / Gain :- 10Kohms unbalance / 42 dB (e)frequency Response -

30 Hz- 20 KHz L / R Line Output ( + 0, -1 dB ) (f)Equalization Bass/ - + / -

dB at 100Hz Mid / Treble 2 KHz / 10 KHz

(g) Outputs, Line Output Line Output Low : -10 dB / -2 dBM Line Output High

(h) S/N ratio Line Output Level : > 70 dB (0 dB, 0.775V)

The Console shall be mounted on standard Rack, The channel of following numbers.

(B) 9 Channel Audio Mixer with ECHO

66 10 No. SITC of Delegate Unit shall enable delegates to speak and listen to the proceedings via a 32024.07 Rupees Thirty

loudspeaker or headphones. The unit shall include a microphone with a red indicator ring, Two Thousand

which shall illuminate when the microphone is on. Twenty Four And

The unit shall include a ‘Possible To Speak’ white LED indicator, which shall illuminate Paise Seven Only

showing the delegate when it is possible to switch on the microphone.

To prevent acoustic feedback, the built-in loudspeaker shall be muted when the

microphone is on, and/or the headphones are connected.

Two 3.5 mm stereo headphone sockets (wired for mono) shall allow two pairs of

headphones to be connected, enabling two delegates to simultaneously use the unit.

The headphone volume level shall be adjustable on the unit for maximum comfort. It

shall also be possible to connect a tape recorder to one headphone socket, and use the

other headphone socket to listen to the proceedings.

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

67 1 No. SITC of Chairman Unit shall enable the user to function as chairman of a conference or 38726.43 Rupees Thirty

meeting. It shall be similar in appearance to the Delegate Unit, and shall also include a Eight Thousand

‘chairman priority button.When pressed, the priority button shall cause all currently active Seven Hundred

delegate microphones to be temporarily or permanently muted, allowing the chairman to Twenty Six And

Paise Forty Three

take control of the meeting.

To prevent acoustic feedback, the built-in loudspeaker shall be muted when the

microphone is on, and/or the headphones are connected.

An optional chime shall be selectable to precede chairman priority calls. [Approved by

Competent Authority i.e. not Below the rank of Executive Engineer ]

68 1 No. SITC of Control Unit shall have features for managing the number of active microphones 95168.26 Rupees Ninety

and determining the operating mode, without the need for a central operator, should be Five Thousand

available. It shall be possible to control up to 150 delegate units and power up to 50 One Hundred

delegate units. Sixty Eight And

Paise Twenty Six

It shall be possible to connect external equipment to extend the system capabilities. There

shall be a built-in loudspeaker and headphone connector to allow the conference to be

monitored by, for example, a stenographer.

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

69 11 No. SITC of EXTENSION CABLE ASSEMBLY - 2MTRS 1059.49 Rupees One

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] ( for Thousand Fifty

connecting conference units Extension Cable Assembly - 2 Mtrs) Nine And Paise

Forty Nine Only

70 1 Ea SITC of extension cable between the units or 14302.61 Rupees Fourteen

between the controller and unit -25 meter long Thousand Three

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Hundred Two

( for conference unit connectivity to the Controller.) And Paise Sixty

71 4 Nos. SITC of Column loudspeaker 40W, metal, black 12472.49 Rupees Twelve

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Thousand Four

Hundred Seventy

Forty Nine Only

72 1 Ea SITC of 3LCD Lamp based projector having wxga (1280x800) or better resolution with 33895.60 Rupees Thirty

minimum white brightness of 3800 lumens and color brightness of 3800 lumens. The Three Thousand

projector should have minimum 1HDMI,1VGA input. Having contrast ratio of 15000:1 Eight Hundred

or more. the projector should have auto vertical key stone correction of +/- 30 degree and Ninety Five And

Paise Sixty Only

Manual Horizontal of +/-30 degree. the projector should have optical lens, throw ratio

1.30-1.56:1. Zoom Factor of 1.2. Lens focus Manual having focal length 16.9mm to

20.28mm. projector should have features like AV mute slide, quick corner and split

function and should support wireless functionality with inbuilt wifi or wifi dongle.

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] (

Make- Epson, Sony or Equivalent)

73 1 Ea SITC of universal Projector mounting kit, with necessary grouting, fasteners etc. with 6848.81 Rupees Six

adjustable height and suitable for all types of projectors. [Approved by Competent Thousand Eight

Authority i.e. not Below the rank of Executive Engineer ] Hundred Forty

Eight And Paise

Eighty One Only

74 1 Ea SITC of 120 inch Self Lock MW (8 x 6) Instalock Slow Retraction Screen, Aspect Ratio- 5334.82 Rupees Five

4:3 [Approved by Competent Thousand Three

Authority i.e. not Below the rank of Executive Engineer ] Hundred Thirty

Eighty Two Only

75 3 Ea Replacing old and U/s Ac Machine By Providing and erecting Inverter based approved 41725.12 Rupees Forty One

make split air-conditioning unit consisting of condensing unit with variable speed fan Thousand Seven

motor, inverter type hermetically sealed rotary compressor with accessories etc. duly Hundred Twenty

connected separately erected evaporating unit and blower motor with its accessories by Five And Paise

means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for (

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control &

MS Stand) with necessary core cutting.

(1)For ISEER Range (KWH/KWH)(3.1 to 3.99)

(B) for 1.5 ton capacity (old-3, New-0 )

76 4 Ea Supply and Erecting of Static Stabilizer suitable for following capacity of A.C Machine 3030.00 Rupees Three

the Stabilizer Must have Minimum Technical Specification are Input working Single Thousand Thirty

Phase Voltage Range Up to 150V-280V.50Hz, Output Voltage Range Up to 200V- Only

240V,50Hz,Autoreset Facility,LED Display for Indicating Voltage,Spike/Surge

Protection,Time Delay Facility,Proper Wall Mount Facility with Required Accessries &

on site 3 year Replacement/Repairing Warranty.

(1) For 1.5Ton Thermal Overload Protection 12 Amp.

77 1 Ea Supplying, installing, testing & commissioning of digital pure sine wave INVERTOR of 26534.72 Rupees Twenty

approved make single phase 230v complete with overload relay & necessary protection Six Thousand Five

with following size of batteries, erected with battery terminal wire, copper lead wire to be Hundred Thirty

connected to load with 10 Amp., 10 kA MCB. Four And Paise

Seventy Two Only

[F] 2000 VA with battery 12V x 2, 150 AH load up to 1250 W

78 2 Ea Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 1275.63 Rupees One

digits LED display, 0 to 750 AC Volts range erected on existing panel board with all Thousand Two

connection, wiring etc .with manufacturers calibration certificate. Hundred Seventy

Sixty Three Only

79 2 Ea Supplying and erecting approved make panel mounting type Digital Ammeter having 3 1558.43 Rupees One

digits LED display, external CT operated, calibrated for 0 to 1000 Amps suitable to Thousand Five

operate on 500 Volt AC , erected on existing panel board with all connection, wiring etc Hundred Fifty

.with manufacturers calibration certificate. Eight And Paise

Forty Three Only

80 4 Ea Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Supply 500 317.14 Rupees Three

V on existing panel board with necessary connections. Hundred

81 6 Ea Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 274.72 Rupees Two

VA burden erected in existing CRCA box duly secured with insulating materials Hundred Seventy

connected to the meter Four And Paise

Seventy Two Only

82 6 Ea Supplying and erecting approved make suitable panel indicator LED type lamp, lens 43.43 Rupees Forty

cover, complete erected with necessary connections. Three And Paise

Forty Three Only

83 1 Ea Replacing old and U/s motor by Providing & erecting open well horizontal mono block 18746.61 Rupees Eighteen

pump set with cast iron body, complete for three phase submersible motor having Thousand Seven

[D] For 5 HP 3 phase open well horizontal mono block pump set suitable for 1350 LPM Hundred Forty Six

to 310 LPM @ 10 to 42 Mtr head suitable for 50/65 mm dia delivery pipe Cat.II And Paise Sixty

( Old-1 , New-0 )

84 1 Ea Replacing old and U/S 3Ph DOL Starter by Supplying and erecting Direct-on-line, Starter 2046.26 Rupees Two

with 15A.rating contractor and with 4-14A. range, directly operated thermal overload Thousand Forty

relay in sheet steel enclosure for 3phase 415V.50 c/s. A.C. motor up to 7.5 H.P.complete Six And Paise

erected on P.W. Block with necessary connection. Twenty Six Only

( Old-1 , New-0 )

85 1 Per Lowering of submersible motor pump set at the depth of following ,complete with 856.48 Rupees Eight

Job required. Nos. and size of casing pipes erected by means of proper chain pulley block & Hundred Fifty Six

pipe wrenches after checking of threads of each pipe with coupling to take the load of the And Paise Forty

pump set and pipe assembly filled up with water Eight Only

(D)For Open well Horizontal submersible pump set for sump well

86 25 Mtr Replacing old and U/s CU Flate Cable By Providing and erecting ISI marked PVC 104.03 Rupees One

insulated PVC Sheathed Flat flexible Submersible copper cable approved make of Hundred Four

following Size. And Paise Three

(B) 3 Core x 2.5 Sq. mm. Only

(old- 25, New- 0)

87 2 Ea Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using 189.88 Rupees One

insulating material, water proofing material, & making the joint complete. Hundred Eighty

(A) Up to 10Sq. mm Nine And Paise

Eighty Eight Only

88 1 Ea Supplying and erecting Orei 1*8 2.0 HDMI Splitter 8 Port with Full ultra HDCP 2.2, 4K 6599.05 Rupees Six

at 60Hz & 3D Supports EDID Control UHDS. Comatible for projector , DVD player, TV Thousand Five

Display, Data transfer rate 10.2 Gigabites per Second, 8 Nos of port Hundred Ninety

(Mahesana/Perusal no.37/2091/ Of 2024 , By Circle office Gandhinagar, Dt.05/03/2024, Nine And Paise

89 20 Mtr. Supplying and Laying of reputed make HDMI Cable from projector /TV to Splitter and 215.31 Rupees Two

Spliteer to Face plate Hundred Fifteen

(Mahesana/Perusal no.37/2091/ Of 2024 , By Circle office Gandhinagar, Dt.05/03/2024, And Paise Thirty

Iten no.22, ) One Only

90 1 Nos. Supplying, Installation, testing and commissioning of Multi Channel amplifier providing 205190.59 Rupees Two

total rated output power 600 W; Minimum 2 Channel Input and Output, Class D, Lakh(s) Five

Nominal Gain 36.2 dB, Signal to Noise Ratio > 103 dB, THD+N < 0.1 %, 2 x 6-pin Thousand One

Euroblock, 3.81 mm, male, parallel 1x RJ45, Audio limiters, high temperature, DC, HF, Hundred Ninety

And Paise Fifty

short circuit, back-EMF, peak current limiters, inrush current limiters, mains over/under

voltage protection

Approved Make: Bose/Dynacord/Bosch

( as per TS No-PB/Godhra/SR-TS No-34/286 of 2025, Dtd 18.3.25, Item No-7)

In Words : Rupees Fifty Five Lakh(s) Ninety Three Thousand Two Hundred Fifteen And Paise Eight Only

I/We am/are willing to carry out the work at ____________% above/below (in Figures)__________________________ percent Above / below (in

words) the estimated rates mentioned above amount of my\our tender works out as under :-

Estimated amount put to Tender Rs._________________

Deduct _____% below Rs._________________

(-)Less For Dismantle Material Rs._________________

Net Amount Rs._________________

Estimated amount put to Tender Rs. _________________

(-)Less For Dismantle Material Rs. _______________

Net Amount Rs. _________________

A I/We hereby declare that I/we have visited the site and fully acquainted my self / our selves with the local situation regarding material,labour and other

factors pertaining to the work before submitting this tender.

B I/We hereby declare that I/we carefully studied the conditions of contract, detailed technical specifications and other tender documents of this work and

agree to execute the same accordingly.

(Signature of the Contractor) Deputy Executive Engineer

Electrical R&B Sub Division

Executive Engineer

Electrical R&B Division

Note 1 Please strike out whichever is not applicable.

2 In the case of tendered amount being quoted incorrectly the quoted pered percentage Below/Above will be considered as final.