Supply Installation Testing and Commissioning SITC of MPS Centrifugal Pumping Plant transformer etc with complete Pumping Equipment and Accessories at Barkot Nagar Palika Pumping Scheme

SITC OF Supply of KIRLOSKAR / WILO MAKE HORIZONTAL MULTISTAGE CENTRIFUGAL PUMP SET IN BRONZE IMPELLAR DISCHARGE 1500 LPM (90 m3/hr), HEAD 290 METER

SITC OF CROMPTON / ABB TEFC/KIRLOSKAR INDUCTION MOTOR IE3 2900 RPM along with HEAVY DUTY MS BASE FRAME, FOUNDATION BOLTS, COUPLING AND COUPLING GUARD COMPLETE

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CONTROL PANEL WITH ONE INCOMING AND THREE OUTGOING OF FOR SUITABLE FOR ABOVE PUMP SET

SUPPLY ,INSTALLATION ,TESTING AND COMMISSIONING(SITC) OF FULLY AUTOMATIC PUMP MOTOR STARTER,

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF 250 AMP CHANGE OVER SWITCH

MAIN PIPING AND VALVES :- FOR SUCTION SIDE: SUPPLY AND FIXING OF DOUBLE FLANGED VALVES INCLUDING NUT BOLTS, WASHER, PRESSURE PACKING ETC. COMPLETE IN ALL RESPECT. ( SITC) AS PER THE FOLLOWING: 150 MM SIZE C.I. D/F SLUICE VALVE, PN 1.6 FOR SUCTION SIDE : 03 NOS

(I) MAKING TEE, BAND, REDUCER AND ENLARGE BY WELDING FOR SUCTION SIDE AND PIPE AS PER REQUIREMENT OF SITE AND PIPING CONDITION, INCLUDING PIPE, LABOUR, MATERIAL, T&P ETC, COMPLETE IN ALL RESPECT. (150 mm dia. x Pump Inlet size MS DF Taper - 3 Nos., 150 mm dia. MS DF 900 Bend -3 Nos. 150 mm dia. MS blind flange - 03 Nos 150 MM DIA MS FLANGES FOR ABOVE : 16 NOS), (II) FOR DELIVERY SIDE AND BYPASS ARRANGEMENT: CAST STEEL SLUICE VALVE 100 MM, CLASS 300 D/F WITH FITTINGS : 05 NOS (III) CAST STEEL NON RETURN VALVE 100 MM, CLASS 300 D/F WITH FITTINGS : 04 NOS, (IV) MS PIPE SUPPLY AND MAKING TEE, BAND, REDUCER AND ENLARGE BY WELDING FOR AND DELIVERY SITE BOTH AS PER REQUIREMENT OF SITE AND PIPING CONDITION, INCLUDING PIPE, LABOUR, MATERIAL, T&P ETC, COMPLETE, (V) FOR DELIVERY SIDE AND BYPASS ARRANGEMENT: CAST STEEL SLUICE VALVE 100 MM, CLASS 300 D/F WITH FITTINGS : 05 NOS, (VI) CAST STEEL NON RETURN VALVE 100 MM, CLASS 300 D/F WITH FITTINGS : 04 NOS, (VII) MS PIPE SUPPLY AND MAKING TEE, BAND, REDUCER AND ENLARGE BY WELDING FOR AND DELIVERY SITE BOTH AS PER REQUIREMENT OF SITE AND PIPING CONDITION, INCLUDING PIPE, LABOUR, MATERIAL, T&P ETC, COMPLETE IN ALL RESPECT (100 mm dia. x Pump outlet size MS DF Taper - 4 Nos. 100 mm dia. MS DF 900 Bend - 4 Nos. 100 mm dia. MS Blind Flange. - 2 No. 100 mm dia. MS Pipes in suitable length - 12 Mtr 150 mm dia. MS Pipes in suitable length - 24 Mtr (FOR COMMON HEADER) 100 mm dia. MS Flange - 36 Nos 100 mm x 150 mm x 150 mm dia. MS A/F Tee - 3 Nos. NECESSARY NUT BOLTS, PACKING ETC)

SITC HOT CRANE OF 05 TONNE WITH 10 METER CHAIN HEAVY DUTY CHAIN PULLEY WITH TRAVELLING TROLLEY, MS GIRDER

POWER WIRING AND EARTHING MATERIAL A. SUBMERSIBLE COPPER CABLE REQUIRED FOR CONNECTION FROM STARTER TO MOTOR, SIZE 70 SQMM * 3 CORE : 90 METER FOR THREE PUMPS B. POWER CABLE FROM MAIN TO SERVO TO STARTER REQUIRED IS ALMUINUM ARM. 150 SQMM * 3.5 CORE : 80 METER C. LUGS AND JOINTING MATERIAL REQUIRED D. EARTHING OF THREE PUMPS, MOTOR AND PANELS : 03 SET

GAUGES :- SUPPLY AND FIXING OF GAUGES AND FITTINGS PRESSURE GAUGE 100 MM DIAL SIZE OF 0-100 KG/ CM2-01NO. COMPOUND GAUGE 100 MM DIAL SIZE OF 0-1 KG/ CM 2 -01 NO. HEAVY DUTY CONTROL COCK-01 NO M.S. NIPPLE PIPES, ELBOWS ETC. REQUIRED FOR FIXING THE ABOVE GAUGES ON PUMP 01 SET.

ELECTRONIC CHLORINE DOSING SYSTEM COMPLETE IN 6 KG PRESSURE, 230 V WITH INSTALLATION, 100 LTR TANK AND CONNECT WITH STARTER COMPLETE

SITC OF ROLLING CONTACT SERVO VOLTAGE STABILIZER 315 KVA (3 PHASE) ISO CERTIFIED, SUITABLE FOR INDOOR USE, WITH STAND AMBIENT TEMPRATURE UPTO 55 DEG-CEL UNIT IS A COMBINATION OF THREE NO SINGLE PHASE AIR-COOLED UNITS IMMERSED IN ONE OIL COOLED TANK WITH SEPARATE CONTROL CIRCUIT FOR INDIVIDUAL CORRECTION IN EACH PHASE, COMBINATION SUITABLE FOR BALANCE-UNBALANCED SUPPLY AND LOAD. THE SERVO STABILIZER SHALL BE COMPLETE WITH HIGH/LOW VOLTAGE CUT-OFF SYSTEM, MCCB & OIL, INPUT VOLTAGE: 280- 460 VOLT, OUTPUT VOLTAGE ; 415(+/-)1% TYPE : ROLLING CONTACT (LINEAR TYPE), 315 KVA

RUBBER INSULATION MAT

400 KVA 11KV/415V 3 Phase Copper Wound Oil Immersed Outdoor Type, Level 2 Distribution Transformer With +5% to -10% in Steps of 2.5% by Off Circuit Tap, Changer with HV cable Box (without Cable Gland)

COMPLETE 4 SET OF EARTHING FOR TRANSFORMERS INCLUDING 2 OUT DOOR JOINTING KIT AND 1 INDOOR JOINTING KIT

SITC OF HT CABLE AS FOLLOWS:- A. HT ALUMINIUM CABLE SIZE 185 SQMM * 3 CORE : 40 METERS (UPTO MPS) B. HT ALUMINIUM CABLE SIZE 70 SQMM * 3 CORE : 180 METERS (TUBEWELL 1 ) C. HT ALUMINIUM CABLE SIZE 70 SQMM * 3 CORE : 180 METERS (TUBE WELL 2)

FOUNDATION: PCC IN 1:1:5:3 IN CEMENT, COARSE SAND AND 20 MM GAUGE STONE HALLAST WITH IRON CORE DUST MIXTURE ( ADDING 2 KG IRON CORE DUST WITH EACH CEMENT BAG) AND MAKING BLOCK FOR PUMP FOUNDATION COMPLETE WITH GROUTING THE FOUNDATION BOLT AS PER SESIGN AND DRAWING GIVEN BY THE PUMP MANUFACTURER INCLUDING ALL LABOUR, MATERIAL, CARTAGE, T & P ETC.

PAINTING:- ENAMEL PAINTING COMPLETE IN ALL PUMP SET FOUNDATION, VALVES , SUCTION AND DELIVERY PIPES, BARREL PIPES AS PER SUITABLE MATCHING COLOUR OR AS PER DIRECTION OF ENGINEER INCHARGE ETC. COMPLETE IN ALL RESPECT

TESTING AT MANUFACTURER PLACE AND AT SITE

INSTALLATION TESTING AND COMMISSIONING OF ABOVE COMPLETE WORKQ

CARTAGE OF ALL MATERIAL (LUM SUM)

ELECTROHARD INDUSTRIAL SOLUTIONS (BID ID -356911)