CA NO. CWE /HILLS /EWS/48 OF 2021-2022 ADDN/ ALTN TO CERTAIN OTM BLDGS AT RUDRAPRAYAG UNDER GE 871 EWS

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in framed work complete all as specified and directed.

Dismantling of framed timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specfied and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of concrete block walling, RR masonary in cement mortar including all quoins archas pillars etc and pre-cast block walling etc complete all as specifed and directed.

Demolition of reinforced cement concrete of any description of any position not otherwise specifically provided for man hole cover slab complete all as specifed and directed.

Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm eachwith shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in any type soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for M-25 (20mm graded aggregates) reinforced cement concrete (design mix) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for M-25 (20mm graded aggregates) reinforced cement concrete (design mix) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for M-25 (20mm graded aggregates) reinforced cement concrete (design mix) as in Chajjas complete all as specified and directed.

M&L for M-25 (20mm graded stone aggragate) reinforced cement concrete (design mix) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for 40mm thick damp proof course in cement concrete 1:2:4, type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in floor finishes complete all as specified and directed.

M&L Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm,on vertical surfaces such as skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for vitrified ceramic light shade coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.09 but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350X250X7 mm / 450X350X7 mm thick, on vertical surfaces such as skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for prepolished chequered cement concrete tiles 30cmx30cmx25mm thick, set, jointed and pointed and in need cement slurry in floor with grey cement and pigment and including 20mm thick screed bed or bedding layer in cement mortor 1:6 complete all specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40 mm aggregate in plinth protection including finishing even and smooth without using extra cement complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1, 20mm graded aggregate as in cover slabs set in CM 1:4 for man holes etc complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams, drain sides or similar works vertical or to batter for rough finished surface of concrete in flat complete all as specified and as directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges rough finished surface of concrete in flat complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surface of concrete in flat complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shspe required incl cranking, bending spirally for hooping for coloumns, hooking ends andbionding with (annealed) not less than 0.90 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over and including 10mm dia in stirrups, spacers and binders, bent to shspe required incl cranking, bending spirally for hooping for coloumns, hooking ends andbionding with (annealed) not less than 0.90 mm dia complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 (20 mm graded aggregate) exc 10 cm width and setting in cement mortar 1:4 complete all as specified and directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Removing excavated material (soil) exc 250 mtr but n exc 500 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 (20 mm graded aggregate) exc 10 cm width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 (20 mm graded aggregate) as in solid building blocks or slabs 10 cm thick (with plain or interlocking joints as directed setting in cement mortar 1:6 complete all as specified and directed.

M&L for providing cement concrete type B1 1:2:4 using 20 mm graded aggregate, as in coping including necessary form work complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surfaces using WPC @ 3% by weight of cement and finishing the surface even and smooth without using extra cement complete all as specified and directed. NOTE -WPC shall be measured and paid separetely.

M&L for preparation of newly plastered wall surfaces and applying two coats oil bound distemper over a coat of primer including making the surface truly smooth by a coat of 3 mm thick wall putty complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

S&F 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. supplied and fixed complete all as specified and direcetd.

S&F for 35mm thick 2nd class hardwood for Glazed skeleton shutters for door open rebated and prepared to receive glass gauge etc. (with sash bars) edges of framing plain, chamfered or rounded , fitted with cuts and mitred beads for securing glass etc. sizes of members of shuttered as specified in SSR Part- I section -8 clause 8.23 (b) complete all as specifed and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panesls, commercial type on bothe sides complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and directed.

S&F powder coated aluminium frame & shutters for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F sheet glass 4.8mm thick, ordinary quality and glazing with oil putty, fixed to aluminium shutter in squares n exc 0.5 Sqm in each pane complete all as specfied and directed.

M&L for rubber beading for fixing glass panes in aluminium frame work complete all as specified and directed.

S&F aluminium anodised grill of size 100mm x 10mm x7mm thick, approved design for windows / ventilators with and including F/U channel complete all as specifed and directed.

S&F aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces any description, over 10cm in width or girth,not otherwise applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 100 mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F Mild steel 375mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extuded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 140mm size floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F of 25mm dia 1.6mm thick harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.11611979 grade St.-240 complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

S&F mild steel screw bolts (machine made) 5 to 10mm dia neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed.

S&F mild steel screw bolts (machine made) 11 to 15mm dia neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.50 cm but n exc 30 cm long complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F of false ceiling of everest designer boards of size 595 x 595 x 4 mm thick fixed on GI snap grid complete all as specified and directed.

M&L for preparation of old steel surfaces any description, over 10cm in width or girth,not otherwise applying a coat of synthetic enamel paint complete all as specified and directed.

M&L for 12 mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L for 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L for 2nd class soft wood Plain fillets, square, rectangular or triangular in section sectional area exc 3 but n.exc 6 Sqcm, clean sawn, secured with mills or brads, wrought fixed with nails complete all as specified and directed.

S&F for 19 mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work complete all as specified and directed.

S&F for continuous (piano) hinges, mild steel, bright finish or electrogalvanised widt of flap when open 40 mm complete all as specified and directed complete all as specified and directed.

S&F mild steel Mortice lock, vertical type, size 100 mm, 2 lever complete all as specified and directed.

S&F 75 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F brass drawer pulls, 3 screw plate with fixed dished pull; 80 mm to 100mm long complete all as specified and directed.

S&F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F in repair vitreous China wash basin, white, flat back, size 550x400mm excluding ditto but including brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing complete all as specified and directed.

S&F in repair 15mm bore dia bib taps, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all specified and directed.

S&F in repair 15 mm bore dia angle valve/ stop cock, cast copper alloy, chromium plated, screwed down, high presure with cruntch or butterfly handle screwed both ends for iron pipe all as specified and directed.

S&F in repair 15mm bore dia chromium plated brass, fancy type 2-in-1 angle cock screwed for iron pipe or union and fixed complete all as specifed and directed.

S&F in repair 15mm bore dia brass chromium plated wall mixer mixing hot and cold water screwed down for iron pipe and fixed to wall complete all as specifed and directed.

S&F in repair 15mm bore dia brass chromium plated WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed to wall complete all as specifed and directed.

S&F in repair brass 125 mm size chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specifed and directed.

S&F 15mm bore dia PVC connection and 600mm long complete all as specifed and directed.

S&F in repair 160x160x90mm size soap dish fixed with chromium plated brass screws complete all as specified and directed.

S&F in repair 20 mm dia CP towel rail 600mm long with hook complete all as specifed and directed.

S&F 32mm dia PVC waste pipe complete all as specifed and directed.

S&F 125/110 mm bore PVC (SWR) 'S' trap complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socket in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bend of any radius complete all as specified and directed.

S&F 100 mm CP Grating fixing with white cement complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Taking up or down 15mm bore dia steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore dia steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

M&L for 15 mm bore dia GI tubing of medium grade with fittings and fixed complete to walls or laid in floors,bore of pipe complete all as specified and directed.

M&L for 20 mm bore dia GI tubing of medium grade with fittings and fixed complete to walls or laid in floors,bore of pipe complete all as specified and directed.

Dismantling of 500 Litre capacity water tanks complete all as specified and directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tank (cylindriacal vertical with closed top) hoisted and fixed in position all as specified in SSR part-I including 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball and nipple screwed for iron pipe and fixed complete all as specified and directed.

S&F 100 bore dis sand cast cast iron soil, waste and vent pipes in any length with or without ears, with lead joints, fixed to walls complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 complete all as specified and directed.

M&L for 100 mm bore dia cast iron soil, waste and vent pipes (sand cast), in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 100 mm bore dia including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in surface channel and drain complete all as specified and directed.

Extra for forming fair finished drain and channel 30 cm inner grith in cement concrete using extra cement in forms mould mitred/stopped ends complete all as specified and directed.

E/M Portion:- Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed.

Taking down unserviceable old existing service/ sub main wiring of any size complete all as specified and directed.

Dismantling and taking down of unserviceable distribution boards alongwith MCB TPN complete all as specified and directed.

Dismantling and taking down of unserviceable MCBs and MCB DP complete all as specified and directed.

M&L for point wiring for one light/ bell/ fan point controlled by one, one way switch with 1.5 Sqmm size, PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3 mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed.

All as per item No.124 herein before but one 3 pin socket outlet 5 Amps independent board controlled by one, one way switch.

All as per item No.124 herein before but one 3 pin socket outlet 5 Amps on the same board.

All as per item No. 124 above but with 4 Sqmm two single core and 2.5 Sqmm one single core as earth wire for 15/16 Amps socket out let, 3 pin on independent board.

S&F switch piano, flush type single pole 15/16 Amp complete all as specified and directed.

Fixing only switch piano, flush type single pole 15/16 Amp complete all as specified and directed.

S&F switch piano flush type single pole, one way 5/6 Amp complete all as specified and directed.

Fixing only switch piano flush type single pole, one way 5/6 Amp complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 5/6 Amp flush type complete all as specified and directed.

Fixing only socket outlet 2 in 1, 3 pin, 5/6 Amp flush type complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5/6 and 15/16 Amp flush type complete all as specified and directed.

Fixing only socket outlet 2 in 1, 5 pin, 5/6 and 15/16 Amp flush type complete all as specified and directed.

S&F ceiling rose surface bakelite 2/3 terminal 65 x 25 mm dia poly carbonate isolated with base plate complete all as specified and directed.

Fixing only ceiling rose surface bakelite 2/3 terminal 65 x 25 mm dia poly carbonate isolated with base plate complete all as specified and directed.

S&F bell push, flush type 5 Amps white or ivory complete all as specified and directed.

S&F csll bell ding dong 230V, AC, single phase complete all as specified and directed.

S&F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

Fixing lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

S&F LED Bulb 9 Watt, cool day light 230/240V AC supply complete all as specified and directed.

S&F LED lights fitting mirror type with high output diffuser 2 feet, 10 watt 220V, AC decorative type with driver holder and LED lamp including connection with three core flexible copper conductor cable or sutaible size complete all as specified and directed.

S&F LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core 23/0.0076 flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core 23/0.0076 flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED bulkhead light fitting 10W luminaires including LED driver holder connceting up with three core flexible copper conductor cable sutaible size complete all as specified and directed.

S&F building security light fitting complete with 25 watt LED type IP 66 pressure die cast aluminium housing and heat resistance toughened glass with frame protection and better optics for uniform distribution etc including GI pipe (light grade) mounting bracket of size 32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required complete with twin core copper conductor cable 1.5 sqmm from ceiling rose to fittings complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed.

S&F MCB DB SPN, 4 way 240 volt , double door type MCB DB suitable for mounting incoming and outgoing MCBs double pole/ single pole complete all as specified and directed.

S&F MCB DB SPN, 8 way 240 volt , double door type MCB DB suitable for mounting incoming and outgoing MCBs double pole/ single pole complete all as specified and directed.

S&F MCB DB SPN, 12 way 240 volt , double door type MCB DB suitable for mounting incoming and outgoing MCBs double pole/ single pole complete all as specified and directed.

S&F 6 to 40 Amp MCB SP with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding complete all as specified and directed.

S&F 63 Amp MCB TPN with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding complete all as specified and directed.

S&F 40 Amp MCB DP with thermal over load as well as magnetic short circuit tripping device with quick, break trip free mechanism, robust design and terminals having heat resistance moulding complete all as specified and directed.

Taking down exhaust fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

Taking down wall mounting fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Refixing of serviceable Exhaust fan with proper cleaning and painting after wiring complete all as specified and directed.

S&F ceiling fan 1200 mm sweep complete with blades, down rods, electronic regulator and accessories, 230 V, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Refixing of serviceable ceiling fan with proper checking for all fittings complete all as specified and directed.

S&F wall mounting Fan complete with accessories 230 V, 400 mm or 16” Wall 80 Wind Pro High Velocity complete all as specified and directed.

Refixing of serviceable wall mounting Fan with proper checking for all fittings complete all as specified and directed.

Taking down of unserviceable 25/35/50 ltr Geysers to keep in safe custody to store and refixing with proper checking for all fittings complete all as specified and directed.

M&L for sub main wiring in PVC casing and caping of reqd size 2 x 6.0 Sqmm PVC insulated multistrand copper conductor with 1 x 4.0 Sqmm PVC insulated multistrand copper conductor as earth continuity wire complete all as specified and directed.

M&L in replacement of earthing complete with galvanished steel earth plate electrode size 600X600X6mm thick burried directly in ground vertically to a depth not less than 2.25m below normal ground level with top edge of earth plate not less than 1.5m below normal ground level connected to and incl GI earth lead wire 4mm dia by means of bolts ,nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and as specified or indicated and testing on completion incl excavation and earth work in any type of strata available at site ,PCC (1:3:6)type C-1 earthing chamber ,pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with GI watering pipe of 20 mm bore medium grade ,wire mesh and lugs ,GI protection pipe of 15 mm bore light grade up to 7.5 mtr long ,etc complete all as specified and directed. NOTE :- GI earth wire and protection pipe beyond 7.5 mtr will be measured and paid separately

RAKESH CHANDRA PANT

ms triveni nirman

NOORI ELECTRIC ENGINEERING WORKS

Harendra Singh Panwar