Loading
Loading…
Loading…
Tender Value
Refer Docs
EMD Value
₹2.1 L
Closing Date
4 Mar 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
18 conditions · 4 needing a document upload
Financial Eligibility Criteria: as per Clause 10.2 of Part-I of IRSGCC2022and as per Railway Board Advance correction slip No.1 dated 14-072022The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less: where V=Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderer shall submit requisite information as per Annexure-F (AnnexureVIB of GCC), along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Financial Eligibility Criteria: As per Clause 10.2 of IRSGCC-2022(As per Advanced Correction slipNo,1 dated. 14.07.2022 to GCC-2022) and the same is mentioned in Para No.10.2 page no. 15 of this tender document. Tenderer should attach Self attested/ Digitally signed copy of Certificate showing minimum average annual contractual turnover as per Annexure VI B ofIRSGCC-2022 (As per Advanced Correction slip No,1dated.14.07.2022 to GCC-2022)in Annexure - "F"Page-32 of Master Document -1 attached to the tender.
Similar Nature of work:- "C.II - Any Civil Engineering Work (excluding Track works / Zonal works)" as per HQrs letter No. W.148/P/SNW/2025 dated 02.12.2025, with the Approval of PCE/SCR.
Technical Eligibility Criteria: as per Clause 10.1 of Part-I ofIRSGCC-2022(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s)during last 07(seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40%of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.
(b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges substructure, superstructure etc.), tenderer must have successfully completed or Page 15/21 1.1.1tenderer must have successfully completed or substantially completed anyone of the following categories of work(s) during last 07(seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or(iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note forb(1): Separate completed works of minimum required values shall also be considered for fulfilment of technical eligibility criteria for different components. (b)(2) In such cases, what constitutes a component in a composite work shall be clearly predefined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required intender documents by way of Special Conditions, a formal agreement duly notarized, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s),and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfil technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35%valueof work to be subletted, in last5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s)fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Note for Item 10.1 of IRSGCC-2022: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500crore and above in last 3financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate. No No Allowed (Optional) Bidders shall confirm and certify
Instructions to Tenderers and Conditions of Tender: Tenders are refer Annexure-I, Tender Form (Second Sheet) Part-I of IRSGCC-2022 is mentioned from page No. 11 - 26 of Master Document -1 attached to the tender.
17 conditions · 5 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender value is including escalation of (-)15% (minus fifteen percent ) on CPWDDSR rates. Tenderer should note this before quoting the rates
The original Bank Guarantee (in lieu of Bid Security) should be delivered in person on any working day to the official nominated (i.e., OS/Tenders/Engg)/BZA Division) as indicated in the tender document before closing date for submission of bids (i.e. excluding the last date of submission of Bids).
All the instructions furnished in the Technical Compliance /Commercial Compliance / Custom / Undertakings /General Instructions are only indicative and not exhaustive. The tenderer shall read the GCC / Tender documents for complete details.
The tenderer shall thoroughly go through the entire tender document and strictly adhere to the instruction and directions given therein.
BZA Division : BZA-VSKP Section: Tadepalligudem : Proposed converting Goods Shed Siding as running line with CSR of 720m at TDD Yard in SSE/P.Way/TDD Section of ADEN/RJY Sub Division. (Project ID : 11.06.16.23.1.55.011) - Proposed Construction of RBG Rooms.
E-03-North-BZA-2026
E-03-North-BZA-2026
Open
Works - General
9 Months
Krishna, Andhra Pradesh
₹0
₹2.1 L
4 Mar 2026
5 Feb 2026
18 Feb 2026
61 items across 3 schedules · ₹1,32,33,422.13 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 280 | 177.5 | 49,700 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 224 | 196 | 43,904 |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 33.6 | 2,123.75 | 71,358 |
| 4 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 39.23 | 7,178.75 | 2,81,622.36 |
| 5 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 73.01 | 9,045.75 | 6,60,430.21 |
| 6 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 49.88 | 10,852.95 | 5,41,345.15 |
| 7 | cum | 141.79 | 11,505.5 | 16,31,364.85 | |
| 8 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 427 | 392.15 | 1,67,448.05 |
| 9 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 883.56 | 927.25 | 8,19,281.01 |
| 10 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 228.16 | 736.4 | 1,68,017.02 |
| 11 | Under 20 cm wide | Metre | 360 | 208.55 | 75,078 |
| 12 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) | Sqm | 1111.72 | 384.3 | 4,27,234 |
| 13 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 116.87 | 9,105.95 | 10,64,212.38 |
| 14 | Cement mortar 1:4 (1 cement :4 coarse sand) | Sqm | 290.33 | 1,123.8 | 3,26,272.85 |
| 15 | Second class teak wood | cum | .4 | 1,42,949.7 | 57,179.88 |
| 16 | Second class teak wood including ISI marked anodised aluminium butt hinges with necessary screws | Sqm | 32 | 4,402.85 | 1,40,891.2 |
| 17 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 24 | 3,167.95 | 76,030.8 |
| 18 | On one side only | Sqm | 24 | 478 | 11,472 |
| 19 | Fixed to steel windows by welding | Kg | 337.8 | 219.1 | 74,011.98 |
| 20 | With 2nd class teak wood beading 62X19 mm | Sqm | 72 | 1,308.35 | 94,201.2 |
| 21 | 125x65x2.12 mm | Each | 24 | 53 | 1,272 |
| 22 | 300x16 mm | Each | 8 | 216.55 | 1,732.4 |
| 23 | 250x10 mm | Each | 8 | 83.9 | 671.2 |
| 24 | 125 mm | Each | 16 | 39.95 | 639.2 |
| 25 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | Metre | 25 | 492.7 | 12,317.5 |
| 26 | 30 mm thick plain PVC door shutters | Sqm | 10 | 3,182.95 | 31,829.5 |
| 27 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Sqm | 261.57 | 1,096.55 | 2,86,824.58 |
| 28 | Size of Tile 600x600 mm | Sqm | 239.28 | 1,553.45 | 3,71,709.52 |
| 29 | 110 mm diameter | Metre | 80 | 377.4 | 30,192 |
| 30 | 1:4 (1 cement: 4 fine sand) | Sqm | 673.92 | 347.05 | 2,33,883.94 |
| 31 | 1:6 (1 cement: 6 coarse sand) | Sqm | 964.59 | 395.35 | 3,81,350.66 |
| 32 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 153.75 | 262.7 | 40,390.13 |
| 33 | New work (three or more coats) | Sqm | 1551 | 39.05 | 60,566.55 |
| 34 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | Sqm | 918 | 185.65 | 1,70,426.7 |
| 35 | Two or more coats on new work | Sqm | 148 | 155.9 | 23,073.2 |
| 36 | One coat | Sqm | 633 | 92 | 58,236 |
| 37 | 63 mm to 45 mm size stone aggregate | cum | 126 | 1,636.05 | 2,06,142.3 |
| 38 | 53 mm to 22.4 mm size stone aggregate | cum | 63 | 1,842.3 | 1,16,064.9 |
| 39 | Stone screening 13.2 mm nominal size (Type A) | cum | 42 | 2,034.35 | 85,442.7 |
| 40 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . | cum | 126 | 1,046.95 | 1,31,915.7 |
| 41 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in- charge. (The panel shuttering work shall be paid for separately). | cum | 72 | 9,823.8 | 7,07,313.6 |
| 42 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 4 | 6,767.4 | 27,069.6 |
| 43 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer | Each | 3 | 3,960.55 | 11,881.65 |
| 44 | 10 litre capacity - coloured | Each | 3 | 1,136.6 | 3,409.8 |
| 45 | 20 mm nominal dia Pipes | Metre | 15 | 537.6 | 8,064 |
| 46 | 25 mm nominal dia Pipes | Metre | 25 | 627.25 | 15,681.25 |
| 47 | 25 mm nominal bore | Each | 2 | 622.4 | 1,244.8 |
| 48 | 15 mm nominal bore | Each | 6 | 506.8 | 3,040.8 |
| 49 | 15 mm nominal bore | Each | 4 | 820.7 | 3,282.8 |
| 50 | 15 mm nominal bore, 107 mm long, weighing not less than 110 gms | Each | 3 | 208.45 | 625.35 |
| 51 | Rectangular shape 600x450 mm internal dimensions | Each | 6 | 1,437.65 | 8,625.9 |
| 52 | Square shape 450 mm internal dimensions | Each | 6 | 1,155.45 | 6,932.7 |
| 53 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | Sqm | 58.43 | 1,505.25 | 87,951.76 |
| 54 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). | Kg | 480 | 638.35 | 3,06,408 |
| Schedule total | ₹1,02,17,267.63 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
MASTERDOCUMENT-11.pdf
ATTACHMENT
MASTERDOCUMENT-22.pdf
ATTACHMENT
1.TenderSchedule.pdf
ATTACHMENT
2.Generalconditionsrevised.pdf
ATTACHMENT
3.buildingconditions.pdf
ATTACHMENT
4.Specificationofconcrete.pdf
ATTACHMENT
5.RevisedBrandsandmakesapprovedlist202530-06-25.pdf
ATTACHMENT
6.earthworkconditions.pdf
ATTACHMENT
7.Specialconditiononsteelreimbursement.pdf
ATTACHMENT
8.TrDSpl.Conditions.pdf
ATTACHMENT
9.DESIGNMIXHQrsLETTERONSPECIALCONDITIONSFORDESIGNMIX2123-03-2022.pdf
ATTACHMENT
10SpecialConditionsfordrgsmodified.pdf
ATTACHMENT
101SAFETYTrackConditions1.pdf
ATTACHMENT
5-1Amendmentno_12toapprovedlistofBrandsandmakesdt30_06_2025_HSFGboltassemblingwithDTIWashers.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].