Loading…
Loading…
Tender Value
₹6.2 Cr
EMD Value
₹12.3 L
Closing Date
24 Jun 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
NOR WORKS
18 conditions · 4 needing a document upload
Financial Eligibility Criteria: as per Clause 10.2 of Part-I of IRSGCC-2022 and as per Railway Board Advance correction slip No.1 dated 14-07-2022 The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less: where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-F (Annexure-VIB of GCC), along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Account duly supported by Audit balance Sheet .
Financial Eligibility Criteria: As per Clause 10.2 of IRSGCC-2022 (As per Advanced Correction slip No,1 dated. 14.07.2022 to GCC-2022) and the same is mentioned in Para No.10.2 page no. 15 of this tender document. Tenderer should attach Self-attested/ Digitally signed copy of Certificate showing minimum average annual contractual turnover as per Annexure V I B of IRSGCC-2022 (As per Advanced Correction slip No,1 dated. 14.07.2022 to GCC-2022) in Annexure - "F"Page-32 of Master Document - 1 attached to the tender
"C.II - Any Civil Engineering Work (excluding Track works / Zonal works
Technical Eligibility Criteria: as per Clause 10.1 of Part-I of IRSGCC-2022 (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender .
(b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfilment of technical eligibility criteria for different components. (b)(2) In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the 1.1.1 Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarized, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfillment of technical eligibility. Such subcontractor must fulfil technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be sub-let, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Note for Item 10.1 of IRSGCC-2022: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work 1.1.2 experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Instructions to Tenderers and Conditions of Tender: Tenders are refer Annexure-I, Tender Form (Second Sheet) Part-I of IRSGCC-2022 is mentioned from page No. 11 - 26 of Master Document -1 attached to the tender
17 conditions · 6 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender value is including escalation of (-)15% (minus Fifteen percent) on CPWD DSR rates. Tenderer should note this before quoting the rates.
The original Bank Guarantee (in lieu of Bid Security) should be delivered in person to the official nominated (i.e. OS/Tenders/Engg) / BZA Division) as indicated in the tender document before closing date for submission of bids (i.e. excluding the last date of submission of Bids).
All the instructions furnished in the Technical Compliance / Commercial Compliance / Custom / Undertakings / General Instructions are only indicative and not exhaustive. The tenderer shall read the GCC / Tender documents for complete details.
The tenderer shall thoroughly go through the entire tender document and strictly adhere to the instruction and directions given therein.
SW I: BZA-VSKP Section : Provision of Additional Lifts (PF No.1- 1No & PF No.2 - 1No, Total : 2 Nos.) for Amrit Bharat Station at Anakapalli Station in SSE/Works/TUNI Section under ADEN/TUNI Sub-Division. SW II: BZA-VSKP Section : Provision of Additional Lifts (PF No.1- 1No & PF No.2&3 - 1No, Total : 2 Nos.) for Amrit Bharat Stations at TUNI Station in SSE/Works/TUNI Section under ADEN/TUNI Sub-Division. SW III : BZA-VSKP Section : Provision of Additional Lifts (PF No.1- 1No & PF No.2&3 - 1No, Total : 2 Nos.) for Amrit Bharat Station at CCT Station in SSE/Works/SLO Section under ADEN/SLO Sub-Division. SW IV : BZA-VSKP Section : Provision of Additional Lifts (PF No.1- 1No & PF No.2&3 - 1No, Total : 2 Nos.) for Amrit Bharat Station at SLO Station in SSE/Works/SLO Section under ADEN/SLO Sub-Division. SW V : BZA-VSKP Section : Provision of Additional Lifts (PF No.1- 1No & PF No.2&3 - 1No, Total : 2 Nos.) for Amrit Bharat Station at APT Station in SSE/Works/SLO Section under ADEN/SLO Sub-Division. SW VI : BZA-VSKP Section : Provision of Additional Lifts (PF No.4&5-1No, Total : 1 Nos.) for Amrit Bharat Station at NDD Station in SSE/Works/NDD Section under ADEN/RJY Sub-Division. SW VII : BZA-VSKP Section : Provision of Escalators (PF No.1,PF No.2&3-1No & PF No.4-1No, Total : 3 Nos.) for Amrit Bharat Station at CCT Station in SSE/Works/SLO Section under ADEN/SLO Sub-Division. SW VIII : BZA-VSKP Section : Provision of Escalators (PF No.1,PF No.2-1No , Total : 2 Nos.) for Amrit Bharat Station at AKP Station in SSE/Works/TUNI Section under ADEN/TUNI Sub-Division.
E-21-North-BZA-2026
E-21-North-BZA-2026
Open
Works - General
12 Months
Krishna, Andhra Pradesh
₹0
₹12.3 L
24 Jun 2026
31 May 2026
10 Jun 2026
50 items across 5 schedules · ₹7,01,36,317.97 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 979 | 177.5 | 1,73,772.5 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 324 | 196 | 63,504 |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 764.36 | 2,123.75 | 16,23,309.55 |
| 4 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 216 | 7,178.75 | 15,50,610 |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 1626 | 392.15 | 6,37,635.9 |
| 6 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 954 | 842.5 | 8,03,745 |
| 7 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 552 | 927.25 | 5,11,842 |
| 8 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 222 | 736.4 | 1,63,480.8 |
| 9 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 1164.1 | 961.3 | 11,19,049.33 |
| 10 | Under 20 cm wide | Metre | 672 | 208.55 | 1,40,145.6 |
| 11 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 383.4 | 9,655.7 | 37,01,995.38 |
| 12 | Concrete of M30 grade with minimum cement content of 350 kg /cum | cum | 344.73 | 10,011.35 | 34,51,212.69 |
| 13 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 818.68 | 9,333.45 | 76,41,108.85 |
| 14 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 11500 | 772.4 | 88,82,600 |
| 15 | 40 mm thick with 20 mm nominal size stone aggregate | Sqm | 576 | 614.2 | 3,53,779.2 |
| 16 | Size of Tile 600 x 600 mm | Sqm | 1152 | 1,464.85 | 16,87,507.2 |
| 17 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 1271.49 | 4,481.3 | 56,97,928.14 |
| 18 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 450 | 738.65 | 3,32,392.5 |
| 19 | 1:4 (1 cement: 4 fine sand) | Sqm | 6014.32 | 399.45 | 24,02,420.12 |
| 20 | Two or more coats on new work | Sqm | 1475 | 146.8 | 2,16,530 |
| 21 | Old work (two or more coats) | Sqm | 7686 | 22.85 | 1,75,625.1 |
| 22 | Old work (one or more coats applied @ 0.83 ltr/10 sqm). | Sqm | 3845.48 | 88.55 | 3,40,517.25 |
| 23 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 207 | 2,434.25 | 5,03,889.75 |
| 24 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 229.7 | 3,551.25 | 8,15,722.13 |
| 25 | In cement mortar | cum | 36 | 2,060.2 | 74,167.2 |
| 26 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. | Kg | 35000 | 5.65 | 1,97,750 |
| 27 | G.S. Sheet | Sqm | 1050 | 164.95 | 1,73,197.5 |
| 28 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 1873 | 263.95 | 4,94,378.35 |
| Schedule total | ₹4,39,29,816.04 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
1Masterdoc0119-03-2026.pdf
ATTACHMENT
2MasterDocument-2.pdf
ATTACHMENT
3GeneralConditions.pdf
ATTACHMENT
4SpecificationsofControlledConcrete.pdf
ATTACHMENT
8RevisedApprovedlistofBrandsandMakes2026withallenclosures26-02-26.pdf
ATTACHMENT
9SimilarNatureofWorks02-12-25.pdf
ATTACHMENT
10SpecificationsforDraging.pdf
ATTACHMENT
11SPECIFICATIONSFORROOFINGWITHCOLOURCOATEDGALVALUMESHEETS.pdf
ATTACHMENT
12Steellconditions.pdf
ATTACHMENT
13SAFETYPRECAUTIONSTOBETAKENATWORKSITE.pdf
ATTACHMENT
14TRDSplConditions.pdf
ATTACHMENT
15Schedule.pdf
ATTACHMENT
7DESIGNMIXHQrsLETTERONSPECIALCONDITIONSFORDESIGNMIX2123-03-2022.pdf
ATTACHMENT
15SPECIALCONDITIONSFORBUILDINGWORK.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .