SPECIAL REPAIRS TO BLDG NOS NP 31 TO KUTCH LINE AT DHRANGAHRA AND PROVN OF ONE SIDED PATH WAY FROM KHUKRI CHOWK TO SHERQUILA CHOWK IN GANDHINAGAR MIL STN

Amount

WORKS TO BE EXECUTED AT DHRANGADHRA MIL STN

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as specified and directed. Note : Depth after punning shall be measured and paid.

Removing excavated material (Soil) not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

M&L for PCC 1:2:4 type B2 (using 40 mm graded as in bed blocks etc. complete all as specified and directed.

M&L for providing cement concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in coping, including necessary form work complete all as specified and directed.

M&L for providing cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in padestal/coping around poles/repair of cutting roads, including necessary form work, finishing even and smooth without using extra cement complete all as specified and directed.

M&L for factory made Pre-cast cement concrete kerb stone masonry type B-1, 1:2:4 (20mm graded stone aggregate) with solid block exc 10cm and set in CM 1:6 complete all as specified and directed.

M&L providing precast cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in landing / cover slab etc setting in CM 1:6 complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L cutting holes into or through stone walls built in cement mortar or cement lime mortar and stone walls built in lime mortar nad walls of cement concrete having superficial area exc 150 sqcm but n.exc 400 sqcm complete all as specified and directed.

Supply and laying sub class old size burnt bricks,sub class' B' laid as cable protection cover complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncourses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified and directed.

M&L for extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F 35 mm thick, 2nd class hard , plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each and refixing in same opening after easing and adjustment complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

S&F, in repair, Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long complete all as specified and directed

S&F, Butt hinges med weight cold rolled mild steel and fixed 100mm size complete all as specified and directed.

S&F, continuous (piano) hinges, mild steel bright finish or electrogalvanised, width of flap 40 mm complete all as specified and directed.

S&F, mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F, for extruded aluminium alloy handles, fabricated type, anodised 100mm size complete all as specified and directed.

S&F, in repair, extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, hasp & staples 125mm in size, safety type alu. anodised fixed with screws complete all as specified and directed.

S&F, in repair, brass chromium plated, tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed.

S&F, in repair, 20mm dia, stainless steel, fancy type,tubular curtain rod fix on decorative brackets with decorative globe at both end complete all as specified and directed.

S&F, in repairs, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F, Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) complete all as specified and directed

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inclding cranking, bendiing spirally for hooping for columns, hooking ends and biinding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F, Rolled section as in main and cross beam hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates. Fe 410 W Gde- E- 250 complete all as specified and directed.

S&F, mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F, Mild steel for roof trusses (framed), trussed purlins, crane gantires, rails and fasternings and heavy bracket framming (beam, tee, angle, channel or flat sections ) incuding distance pieces, clats etc. and confirm to Fe-410-W Gde - E 250 including one shop coat of zinc chrome primer complete all as specified and directed.

M&L for rolled mild steel angle iron or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, Aluminium anodised windows/ ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- sheet glass, wire cloth, lock, etc shall be measured and paid seperately.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction.

S&F, Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F, in repair, 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber frame work in cup boards, rebated or flat edged fixed in repairs complete all as specified and directed.

M&L for 6mm thick external teak wood lipping fixed to18/19mm thick block or Veneered particle boards with nails complete all as specified and directed.

M&L for machine cut kota stone slab, 450x600mm ( 18"X24"), 20-25mm thick as in flooring laid over and including cement mortar screed bed of 15mm thick in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

M&L for rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 75mm thick cement concrete type C2 1:3:6 (40mm graded aggregate) in sub base for interlocking paver blocks complete all as specified & as directed.

M&L for 25 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and as directed by Engineer - in - Charge

M&L for coloured glazed ceramic tiles of size300x200/ 350x250x7mm/ 450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:4 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Taking up or down steel tubing and connections complete all as specified and directed for 15mm bores of pipe complete all as specified and directed.

Taking up or down steel tubing and connections complete all as specified and directed for 20mm bores of pipe complete all as specified and directed.

Taking up or down steel tubing and connections complete all as specified and directed for 25mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for 15mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for 20mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for 25mm bores of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 15mm bores of pipe.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 20mm bores of pipe.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 25mm bores of pipe.

S&F, 32mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

S&F, in repair, bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

Supply only Pillar taps cast copper alloy with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, in repairs, stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, in repair, 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F, in repair, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F, in repair, Grating, square, 150mm size of PTMT (minimum weight 100gms) complete all as specified and directed.

Supply only PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F, in repair, 75 mm outer dia PVC (SWR) floor trap, plain with Grating including joining with solvent complete all as specified and directed.

S&F, in repairs, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for Salt glazed stoneware (SGSW) drain pipes laid in trenches and jointed for 200mm bore internal dia of Grade 'A' pipe laid and jointed complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished and reforming benching as required for 200mm bore of pipe complete all as specified and directed.

S&F, in repairs, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

Supply only PVC waste pipe 32mm bore of size 900mm to 1200mm long complete all as specified and directed.

S&F, in repair, chromium plated, Soap dish holder complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair, white, glazed earthen ware vitreous china wash hand basin of size 550mm x 400mm with and including CI brackets, 32mm bore brass CP waste coupling inlet/outlet, PVC flexible pipe, 600mm size of r15 bore pipe with brass nut and washers etc complete all as specified and directed.

S&F, in repair, brass chromium plated shower rose with or without swivel joint, 125mm size complete all as specified and directed.

S&F, in repair, kitchen sink with out drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all bowl size 600mm x 600mm x 230mm to 260mm complete all as specified and directed.

S&F, in repair, 0.63mm thick, stainless steel plate rack of size 1200mm x 900mm x 180mm complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of cement (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and over in section, an any position (framded) complete all as specified and directed.

Dismantling of timber scantling but fillet rails, post rafter purlin etc under 40 sq cm in section (unframed) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of asbests cement (corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes of size 100mm jointed in neat cement mortar and taking out of trenches if required complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes of size 200mm jointed in neat cement mortar and taking out of trenches if required complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan,socket or power) complete,including fixture and fitting such as as switches, ceiling roses, pendants, regulators, sockets,etc excluing light fittings etc,removing materials to store for keeping in safe custudy or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surface of walls, ceiling, floor etc to match with the existing surface complete all as specified and directed.

M&L for point wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(c) One 3 pin socket outlet 5 amps on independent board controlled by one switch.

(d) One bell/buzzer point controlled by one bell push

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including PVC non metalic conduit lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one socket outlet three pin 15 Amps complete all as specified and directed.

S&F, Modular Switch, 1 way, 6A, 1 module including suitable outer cover complete all as specified and directed.

S&F, Modular Switch, 1 way, 16A, 1 module including suitable outer cover complete all as specified and directed.

S&F, Modular Bell push 6A 1 module complete all as specified and directed.

S&F, Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed.

S&F, Socket, 6A, 2/3 pin combined 2 module type including suitable outer cover complete all as specified and directed.

S&F, Socket, 6A/16A, 2/3 pin combined 2 module type including suitable outer cover complete all as specified and directed.

S&F, fan step regulator, suitable for 1200mm sweep ceiling fan 120W - 2 module type complete all as specified and directed.

S&F, Sheet metal enclosure single pole and neutral 20 amps complete with connection as all specified and direced. .

S&F, in repairs, sheet metal distribution board, SPN, 8 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed

S&F, Ceiling rose, PVC/poly carbonate,isolated body, three terminals complete all as specified and directed.

S&F, in repairs, miniature circuit breakers, type curve ‘B’ , 10 KA, SP, 6 to 32 Amps complete all as specified and directed.

S&F, in repairs, miniature circuit breakers, Single pole and neutral, type curve ‘C’ 10KA, 32-40 Amps 230 Volts. complete all as specified and directed.

S&F sub main wiring complete with 04 runs of 6sqmm PVC insulated unsheathed single core multistrand copper conductor cable of 1100 volts grade drawn through new casing caping surface in wall alongwith accessories fixed on walls/floors/ceiling etc with two run of 4 sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan AC single phase 230 volts ,50 Hz metal body of size 300 mm sweep, ISI Marked with louvers and all fixing arrangements including making the hole in wall and good surface finishing all as specified and directed, confoming to Make Havells/ Bajaj/Crompton or equivalent make

S&F, in repair, GI pipe, 40mm bore, light grade, laid below road/fixed along the poles / walls with necessary clamping, etc complete all as per specified and directed.

Supply and lay cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm, 2 core including connecting, testing and commissioning complete all as specified and directed.

Taking down carefully all unsv cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of any size complete all as specified and directed.

Taking down carefully old/unserviceable light fitting of any type, any size complete all as specified and directed.

Taking down carefully old/unserviceable DB Box of any type, any size including US MCB SPN/SP complete all as specified and directed.

Taking down carefully old/unserviceable of earthing with galvanized iron earth complete all as specified and directed.

Taking down carefully old/unserviceable submain wiring of any type, any size complete all as specified and directed.

S&F, in repair, decorative wall light fixture made up of polycarbonate suitable for 9 W LED Lamp including connected and testing complete all as specified and directed as per make of Havells cat part no LHFOFTE1TZ1W012 or equvalent make as approved by GE.

S&F, in repair, lamp holder, insulated body with back plate suitable for batten fittings including LED lamp 9W complete all as specified and directed.

S&F, in repair, decorative box type LED light fitting, 1 x 20 Watt, 230 V,C surfacce mounting white powder coated CRCA sheet steel housing with crescent light opening in a perforated metallic frame complete with 20 W LED tube complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed by Engr-in-charge.

S&F, in repair, bulk head LED light fittng 10 W IP65 Water proof heavy aluminium body wall/ceiling mounted complete with all accessories and including connection up with twin core flexible copper conductor cable with suitable size complete as all specified and directed.

S&F, in repair, security light luminaries 25 watt with wall mounting bracket of suitable size and clamps, nut bolts etc.having pressure die cast housing with epoxy power coated dark graphite grey colour finish,prismatic polycarbonate cover with individual LED lenses-IP65 prewired Conforming to Crompton Cat Part No. LSTO-25-CDL or of equivalent make as approved by GE.

S&F, in repair, exhaust fan AC single phase 230 volts ,50 Hz metal body of size 250 mm sweep, ISI Marked with louvers fixing including connecting and testing complete all as sepcifreid and directed.

Taking down existing exhaust fan AC single phase 230 volts, 50 Hz metal body of size 250 mm sweep, with louvers and all fixing arrangements all as specified and directed.

Taking down ceiling fan single phase, AC 230/240 Volts, 50 Hz, 1200/1400mm sweep complete with bladed and deposit to MES yard complete all as specified and directed.

S&F, in repair, mirror light fixture made up of polycarbonate suitable for 9 w LED Lamp 2 feet complete all as specified and directed.

Taking down electric energy meter and re-fixing the same complete all as specified and directed.

S&F, water heater storage type of capacity 25 ltrs suitable for 230 volt 50 Hz single phase AC supply with 5 star rating including necessary fixing arrangements in stone/brick masonary wall with plug top including hot & cold water pipes connected to water supply line complete all as directed by Engr-in-charge.

M&L, in repairs, earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M. [ii] PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

WORKS TO BE EXECUTED AT GANDHINAGAR MIL STN

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for surface dressing n.exc 15 cm deep in soft/loose soil complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning including watering and consolidation complete all as specified and directed. Note : Depth after punning shall be measured and paid.

M&L for Forming embankments of soil including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base complete all as specified and directed.

Removing excavated material (Soil) not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

M&L for PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation, sub base, filling and mass concrete complete all as sepcifeid and directed.

M&L precast curve stone of cement concrete type C-1 (1:3:6) in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in cement mortar (1:4) complete (Note size of curve stone 300X150X450 mm)

M&L for Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L brick work using fly ash bricks curved or straight on plan exc 6 mtr mean radius built in cm (1:6) complete all as specified and directed.

M&L 100 mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) in Sub-floors, sub-bases, Floors and Pavings, etc.

M&L for machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for preparation of new surfaces of wall and applying two coats of synthetic enamel paint over a coat of priming paint as primer complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

Shree Builders

divyarsh entrprise

DMA PROJECTS

Ramdev and Sons

SNEH TRADERS

M/s SK Traders

Navkar Enterprises