Construction of Annadanam Shed in the premises of Sv Temple (Balaji Mandir) at Kurukshetra in Haryana State

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement corcrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) excluding cost of centering and shuttering upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately.

-do-- All works upto plinth level

-do- For Plinth beams

-do- Columns up to basement

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing inposition and binding all complete upto plinth level .Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes Cement mortar 1:6 ( 1 cement : 6 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness (Total Coated Thickness-TCT), Coating: Alu-Zinc coating AZ150 GSM. Tensile strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc.,complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW).

Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply and fixing of stainless steel SS-304 grade tubes, sections, plates , sheets and pipes of all sizes and diameters etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using SS welding rods including buffing , polishing , lacquer finishing , to present seamless finishing etc., complete as directed during execution .

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.