Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹2.8 LAccepted-AOC | ₹2.8 L | L1 | Accepted-AOC L1 |
| 2 | L2₹3.0 L+₹15,000 (5.36%)Rejected-AOC | ₹3.0 L+₹15,000 (5.36%) | L2 | Rejected-AOC L2 |
| 3 | L3₹3 L+₹20,000 (7.14%)Rejected-AOC | ₹3 L+₹20,000 (7.14%) | L3 | Rejected-AOC L3 |
| 4 | L4₹3.1 L+₹35,000 (12.5%)Rejected-AOC | ₹3.1 L+₹35,000 (12.5%) | L4 | Rejected-AOC L4 |
| 5 | L5₹3.6 L+₹80,000 (28.6%)Rejected-AOC | ₹3.6 L+₹80,000 (28.6%) | L5 | Rejected-AOC L5 |
Tender Value
Refer Docs
EMD Value
₹5,000
Closing Date
20 Jan 2020, 2:00 pmClosed
VARGHESE P O
DMM P AND P FACT LTD
Replacement of Damaged cone of W2 Heat Exchanger in SA Plant, FACT CD, during ATA 2020.
2020_FACT_532510_1
04097/2019-2020/E20787
Limited
Miscellaneous Services
Lump-sum
90 days
AMBALAMEDU
This tender is issued on limited tender basis from the registered bidders of FACT (CD) (list CDM105B)
4 documents required · 4 mandatory
₹0
₹5,000
Yes
30 Jan 2020
2 Jan 2020
21 Jan 2020
2 Jan 2020
20 Jan 2020
2 Jan 2020
Replacement of Damaged cone of W2 Heat Exchanger in SA Plant, FACT CD, during ATA 2020.
Fabrication of new W2 cone and bellow: Work involves :- Collect requisite material from CD-stores and transport to the site. Marking 8 mm SS 304 plates for fabrication, as per FEW Dwg No.1714314 R0. and taking existing site measurements. Cutting the plates using plasma cutting machine and grinding and bevelling the edges. The bevel angle will be strictly as per dwg. Rolling and forming the plates to get the required symmetry as per dwg. Fit up / setting the plates to prefabricate the cone of W2 as per FEW dwg1714314 R0. The site conditions shall also be looked into for prefabrication. The bevel gap shall be strictly maintained as per dwg. The curvature edges shall be rolled and formed to meet the drawing requirement. Full welding the fabricated cone with manhole using SMAW (arc welding). First bed outlet duct up to 1.5 m from the standout of the cone shall be fabricated by the contractor along with the fabrication of cone. All weld joints shall be ground properly and DP test shall be done on all weld joints. For fabrication of bellow as per detail shown in FEW Dwg. No 1714314 R0, cut and bend SS 316 plate 5 mm thk to the required curvature and full weld the joints after fit up. Site conditions should be considered while fabricating the bellow.
M M THAMBI
V M MUHAMMED
PAREETH V V
NG PANICKER ENGINEERING CONTRACTOR
M A ALI
VIKRAMAN NAIR S
HASSAN MM
stage.html
html • 0.06 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_557625.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .