Special repair to toilet block at old Bus Stand Sarkaghat Distt. Mandi HP

Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to approved dumping site, stacking serviceable and unserviceable material separately including cutting einforcement bars (Serviceable material like steel bars to be handing over to the deptt .), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within all leads as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm (Thirty centimeter) in depth, 1.5 m in width as well as 10 sqm (Ten square meter ) on plan) including getting out and disposal of excavated earth lead upto approved dumping site, All kinds of soil, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material upto approved dumping site (Serviceable material like Bricks to be handing over to the deptt .) : In cement mortar, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all leads (Serviceable material like adoors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfast etc. to be handing over to the deptt .) : Of area 3 (Three ) sq. metres and below, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within all leads (Serviceable material like adoors, windows and clerestory window shutters (steel or wood) shutter including chowkhats, architrave, holdfast etc. to be handing over to the deptt .) : Of area 3 (Three ) sq. metres and below , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within all leads, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Dismantling 15 to 40 mm (Fifteen to Forty milimeter) dia G.I. pipe including stacking of dismantled pipes (within all lead and serviceable pipes to be handed over to the deptt.) Internal Work- Exposed on wall , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Dismantling of road gully chamber of various sizes including C.I. grating with frame including stacking of useful materials near the site and disposal of unserviceable materials within all leads including refilling the excavated gap. , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (One Cement isto One and half coarse sand isto Three graded stone aggregate) 20 mm (Twenty milimeter) nominal size. , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete including cost of binding wire upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Repairs to plaster of thickness 12 mm to 20 mm (Twelve to Twenty milimeter)in patches of area 2.5 sq. (Two point five ) meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. With cement mortar 1:4 (One cement isto Four fine sand) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.)

6 mm (Six milimeter) cement plaster of mix : 1:3 (One cement isto Three fine sand) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.)

Providing and applying plaster of paris putty of 2 mm (Two milimeter) thickness over plastered surface to prepare the surface even and smooth complete. , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.)

Stone soling properely hand packed filling interstics with spalls and consolidating with power road roller to the requested gradient and camber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm (One hundred milimeter) spread thickness (finished work including materials and labour), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (One Cement isto Three coarse sand isto Six graded stone aggregate) 20 mm (Twenty milimeter) nominal size , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (One cement isto Two coarse sand isto Four graded stone aggregate 20 mm (Twenty milimeter) nominal size , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (Twenty milimeter) thick cement mortar 1:4 (One cement isto Four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. Complete. Size of tile 600x600 mm (Six hundred into Six hundred milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (Twelve milimeter) thick bed of cement mortar 1:3 (One cement isto Three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete., including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately): For fixed portion : Powder coated aluminium (minimum thickness of powder coating 50 (Fifty) micron), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 (Fifty) micron), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 12 mm (Twelve milimeter) thick Prelaminated partical board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. Pre-laminated particle board with decorative lamination on both sides, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm (Five milimeter) thickness (weight not less than 12.50 kg/ sqm), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125x75x4 mm (One hundred twenty five into Seventy five into Four milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm (Three hundred into Ten milimeter)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm (Three hundred into Sixteen milimeter)

Providing and fixing 150 mm (One hundred fifty milimeter) bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm (One hundred twenty five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (One hundred milimeter) sand cast Iron P or S trap, 10 (Ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (Five hundred eighty into Four hundred forty milimeter) with integral type foot rests, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 630x450 mm (Six hundred thirty into Four hundred fifty milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm (Four hundred thirty into Two hundred sixty into Three hundred fifty milimeter)or 340x410x265 mm (Three hundred forty into Four hundred ten into Two hundred sixty five milimeter) sizes respectively , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 600x450 mm (Six hundred into Four hundred fifty milimeter) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (Six milimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe: 32 mm (Thirty two milimeter) dia, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 100 mm (One hundred milimeter) sand cast Iron grating for gully trap, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 600x120x5 mm (Six hundred into Oner hundred twenty into Five milimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (Forty milimeter) long screws, rawl plugs etc.,complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : Sand cast iron S&S as per IS: 3989, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm (Fifteen milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm (Fifteen milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing PTMT stop cock of approved quality and colour . 15 mm (Fifteen milimeter) nominal bore, 86 mm long, weighing not less than 88 (Eighty eight ), gms , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (One hundred thirty eight milimeter) , breadth 102mm (One hundred two milimeter), height of 75mm (Seventy five milimeter) with concealed fitting arrangements, weighing not less than 106 (One hundred six ),gms., including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 15 mm (Fifteen milimeter) nominal bore , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm (Fifteen milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.nominal bore

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes. 75 mm (Seventy five milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes. 110 mm (One hundred ten milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion. Bend 87.5° 110 mm (One hundred ten milimeter) bend, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm (Seventy five milimeter) bend, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 75 mm (Seventy five milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm (One hundred ten milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Constructing brick masonry manhole in cement mortar 1:4 ( One cement isto Four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (One Cement isto One and half coarse (zone- III) isto Three graded stone aggregate 20 mm (Twenty milimeter) nominal size), foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm (Forty milimeter) nominal size, inside plastering 12 mm (Twelve milimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto Four graded stone aggregate 20 mm (Twenty milimeter) nominal size finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty fiveinto Six hundrd ten milimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall : 15 mm (Fifteen milimeter)dia nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall : 20 mm (Twenty milimeter) dia nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (One cement isto Two fine sand) including testing of joints etc. complete : 450 mm (Four hundrd fifty milimeter) dia RCC pipes, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Please Enable Macros to View BoQ information