REPAIRS / POLISHING TO CERTAIN ITEMS OF WOODEN FURNITURE UNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Chair writing :- Removing of the following old broken/Unserviceable parts from chair writing and Supply and Fixing new parts made out of well seasoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engineer-in-charge.. Drg No. FD-20,202,250 & 280

S&F Front leg

S&F Rear leg

S&F Front rail

S&F Rear rail

S&F Side rail

S&F Stiffener 'H' type

S&F Top Rails

S&F Arms

Chair Dining :- Removing of the following old broken/Unserviceable parts from chair Dining and Supply and Fixing new parts made out of well easoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-16,203,228 & 279

S&F Front leg

S&F Rear leg

S&F Front rail

S&F Rear rail

S&F Side rail

S&F Stiffener 'H' type

S&F back rest stiffener

S & F Corner between leg and rail 75mmx25mm

Chair Dining MAP : Removing of the following old broken/Unserviceable parts from chair Dining MAP and Supply and Fixing new parts made out of well seasoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD/E6/MAP/04

S&F Front leg

S&F Rear leg

S&F Front rail of Seats

S&F Rear rail of Seats

S&F Side rail of Seats

S&F Stiffener 'H' type

S&F Back Rest stiffener

S&F Corner between leg and rail 75mmx25mm

Taking out old U/S seat and S & F new seat shall be 75 mm thick 32 density foam covered with leathrite foam fitted on plywood for seat 12mm thick BWR, raxine of approved quality and colour on seat of chair Dining work should be done exactly as per existing shape and size,including tightening of frame with bamboo pins,screw wood ss before fixing of seat. Rest all as per drg and directed by Engr-in-charge.Note - Cost of raxine not less then Rs 250/- per mtrs

Chair Easy : Removing of the following old broken/Unserviceable parts from chair Easy and Supply and Fixing new parts made out of well seasoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engineer-in-charge.. Drg No. FD-17,201 & 229

S& F Front leg

S& F Rear leg

S& F Arms

S& F Front rail of seat frame

S& F Rear rail of seat Frame

S& F Side rail of seat frame

S& F Side rail of back frame

S& F Lower Rail of back frame

S& F Uper Rail of back frame

Chair all type :Recanning of chairs CBA/CBB wooden chair, bin soiled linen, chair easy, chair dinning, chair writing etc with 2mm wide new plastic cane and 0.4mm thick cream/white half round seat and back and border to be covered with 3 to 4 mm wide ½ round cane and tightening of frame before caning complete all as specified and shown in drawing. Make : Premium/Swastic/Shah

Sofa Set 5 Seater/4 Seater :- Removing of the following old broken/Unserviceable parts from Sofa 5 Seater & 4 Seater and Supply and Fixing new parts made out of Ist class hard wood teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-281

S& F Front Leg

S& F Rear leg

S& F Arms

S& F Batten

S& F Front Long Rail of 3 Seater Seat frame

S& F Rear Long Rail of 3 Seater Seat frame

S& F Upper Long Rail of 3 seater back frame

S& F Lower long Rail of 3 seater back frame

S& F Side Rail of seat frame 3 seater and single seater

S& F Side Rail of Back frmae 3 seater and single seater

S& F Front Rail of single seater Seat frame

S& F Rear Rail of single seater seat frame

S& F Upper Rail of Single seater back frame

S& F Lower Rail of single seater back frame

S& F PVC Shoes

Replacing of existing old cushion foam size 22”x21”x4” from seat and back of Sofa set and supply and fixing of new cushion foam 22”x21”x4” (U Foam) 32 density of sleep well OR Godrej PURITO or ,kurlon & covered with cloth tapestry as per sample approved by GE (Cost of tapestry cloth not less than Rs 385/- per meters). The tapestry cushione cover shall have zip arrangement to accomodate the cushion. All as specified and directed by Engineer-in-charge.

Bed Plywood Top :Removing of the following old broken/Unserviceable parts from Bed Plywood top and Supply and Fixing new parts made out of well seasoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-213,245,246 & 247

Removing of old U/S Existing ply wood top from Bed Ply Wood Top and S & F of new top 12 mm thick ply wood commercial face BWR Grade of same shape and size rest all as per Drg and as Directed by Engr-in-Charge.

Removing of old U/S teak face ply wood 4 mm thick from Head Board and S & F new 4 mm thick one side teak face on both side of Head Board with 4 mm thick teak wood beading around the head board after repairing the complete head board. Rest all as per drg and as directed by Engr-in-Charge.

All as per item No.9.02 above but Foot board.

Long rail

Table Bed Side : Removing of the following old broken/Unserviceable parts from Table Bed Side and Supply and Fixing new parts made out of well seasoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-28,248 & 276

Removing of the old broken /Unserviceable sides from Table Bed Side and Supply and Fixing New sides made of 18mm thick veneered teak bace particle board exterior grade.

Removing of the old broken /Unserviceable top from Table Bed Side and Supply and Fixing New top made out of 18mm thick prelaminated particle board exterior grade on top.

Removing of the old broken /Unserviceable bottom from Table Bed Side and Supply and Fixing New bottom made out of 18mm thick veneered teak wood particle board, exterior grade.

Removing of the old broken /Unserviceable shelves from Table Bed Side and Supply and Fixing New shelves made out of 12mm thick veneered teak face particle board, exterior grade.

Removing of the old broken /Unserviceable back ply from Table Bed Side and Supply and Fixing New back ply 6mm thick plywood, BWR grade, commercial type .

Table Dressing Ladies- Removing of the following old broken/Unserviceable parts from Table Dressing Ladies with Mirror and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-32,251 & 378

New top made of 18mm thick prelaminated particle board exterior grade, both side laminated Rest all as specified in the drg and as directed by Engineer-in-charge.

New 5 mm thick mirror of Make : Atul/Modigaurd with New Teak wood frame & 6mm thick plywood commercial type.

New drawer with front of 18mm thick prelaminated particle board, exterior grade, both side laminated , back and sides of 12mm thick teak wood planks and bottom with 6mm thick plywood commercial grade Rest all as specified in the drg and as directed by Engineer-in-charge.

Removing of U/S knob and S&F new knob best quality as per drg and directed by Engr-in-charge .

M&L for removing UNSV Glass sliding shutter with aluminium channel from table and S&F new Glass shutter made out of 5mm thick glass plain with aluminium channel 20 mm width two way. Rest all as specified in the drg and as directed by Engineer-in-charge.

New 12mm thick back ply BWR Gde Plywood.

Table Dressing Gents :Removing of the following old broken/Unserviceable parts from Table Dressing Gents with Mirror and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-31 & 230

Removing of the old broken/Unserviceable top from Table Dressing Gents with Mirror and Supply and Fixing New top made of 18mm thick prelaminated particle board exterior grade, both side laminated Rest all as specified in the drg and as directed by Engineer-in-charge.

Removing of the old broken/Unserviceable mirror from Table Dressing Gents with Mirror and Supply and FixingNew 5 mm thick mirror of Make : Atul/Modigaurd with New Teak wood frame & 6mm thick plywood commercial type at back as per drg and as directed by Engineer-in-charge.

Removing of the old broken/Unserviceable drawer from Table Dressing Gents with Mirror and Supply and Fixing New drawer with front of 18mm thick prelaminated particle board, exterior grade, both side laminated , back and sides of 12mm thick teak wood planks and bottom with 6mm thick plywood commercial grade Rest all as specified in the drg and as directed by Engineer-in-charge.

Removing of the old broken/Unserviceable knob from Table Dressing Gents with Mirror and Supply and FixingNew knob of best quality as per drg and directed by Engineer-in-charge.

Removing of the old broken/Unserviceable back ply from Table Dressing Gents with Mirror and Supply and FixingNew 12mm thick back ply, BWR Gde Plywood.

Table Centre- : Removing of the following old broken/Unserviceable parts from Table Centre and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge.. FD-29,235 & 274

Removing of the old broken/Unserviceable top table center and S and F New Top of table centre made out of 18mm thick prelaminated particle board exterior grade both side laminated and providing with 4 mm thick teak wood beading duly polished all round the top complete,including tightening of frame with bamboo pins,screw wood ss before fixing of top. all as shown in drg and directed by Engr-in-Charge Make- Eco board/Archid/Bhutan Board Green Ply

Short rail.

Long rail.

Stiffener.

Table 3'x2' with and without drawer- : Removing of the following old broken/Unserviceable parts from Table 3'x2' with and without dr and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-41,224,231,283 & 284

Removing of the old broken/Unserviceable top from Table 3'x2' and Supply and Fixing New top made of 18mm thick prelaminated particle board exterior grade, both side laminated Rest all as specified in the drg and as directed by Engineer-in-charge.

Short rail.

Long rail.

Removing of the old broken/Unserviceable drawer from Table 3'x2' and Supply and Fixing New drawer with front of 18mm thick prelaminated particle board, exterior grade, both side laminated , back and sides of 12mm thick teak wood planks and bottom with 6mm thick plywood commercial grade Rest all as specified in the drg and as directed by Engineer-in-charge.

Removing of U/S knob and S&F new knob best quality as per drg and directed by Engr-in-charge .

Table Peg : Removing of the following old broken/Unserviceable parts from Table Peg and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No FD-46,236 & 277

Removing of the old broken/Unserviceable top from table peg and Supply and Fixing New Top of table centre made out of 18mm thick prelaminated particle board exterior grade both side laminated and providing with 4 mm thick teak wood beading duly polished all round the top,including tightening of frame with bamboo pins,screw wood ss before fixing of Top. Complete all as shown in drg and directed by Engr-in-Charge.

Side rail.

Stiffener.

S&F Corrner of 50x50x25mm

Table Writing : Removing of the following old broken/ Unserviceable parts from Table Writing and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-249 & 275

Removing of the old broken/Unserviceable top from Table writing and Supply and Fixing New Top of table Writing made out of 18mm thick prelaminated particle board exterior grade both side laminated and providing with 4 mm thick teak wood beading duly polished all round the top,including tightening of frame with bamboo pins,screw wood ss before fixing of Top. Complete all as shown in drg and directed by Engr-in-Charge.

Taking out old U/S door of cup boards table writing and S&F new door made of 18mm thick prelaminated particle board exterior grade both side laminated and providing with 4mm thick teak wood beading dully polished all round and peiano type hinges compete all as shown in drg.

Taking out old U/S Side of cup boards table writing and S&F new sides made of 18mm thick prelaminated particle board exterior grade both side laminated compete all as shown in drg.

Removing of the old broken/Unserviceable back ply from table writing and Supply and Fixing Back ply of 6mm thick ply commercial BWR Grade as per drg.

Stiffener

Removing of the old broken/Unserviceable drawer from Table writing and S and F New drawer with front of 18mm thick prelaminated particle board, exterior grade, both side laminated , back and sides of 12mm thick teak wood planks and bottom with 6mm thick plywood commercial grade Rest all as specified in the drg and as directed by Engineer-in-charge.

Removing of U/S knob and S&F new knob best quality as per drg and directed by Engineer-in-charge.

Long Rail

Short Rail

Teapoy: Removing of the following old broken/Unserviceable parts from Teapoy and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-232 & 284

Removing of the old broken/Unserviceable top from Teapoy and S and F New Top of teapoy made out of 18mm thick prelaminated particle board exterior grade both side laminated and providing with 4 mm thick teak wood beading duly polished all round the top,including tightening of frame with bamboo pins,screw wood ss before fixing of top. Complete all as shown in drg and directed by Engr-in-Charge.

Long rail.

Short rail.

Stiffner 'H' Type

Table Dining 6/8 Pers Removing of the following old broken/Unserviceable parts from Table Dining 6/8 Pers and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No. FD-46,236 & 277

Removing of the old broken/Unserviceable top from Table Dining 6/8 per and S and F New Top of Table dining 6/8 pers made out of 18mm thick prelaminated particle board exterior grade both side laminated and providing with 4 mm thick teak wood beading duly polushed all round the top ,including tightening of frame with bamboo pins,screw wood ss before fixing of top.Complete all as shown in drg and directed by Engr-in-Charge.

Long rail.

Short rail.

S& F Corrner of 100x100x25mm

Side Board Removing of the following old broken/ Unserviceable parts from Side Board and Supply and Fixing new parts made out of Ist class hard wood Teak well seasoned and 18mm thick prelaminated particle board both side laminated exterior grade shade as directed made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge Drg No. 26,241 & 371

Taking out old U/S front single door of side board and S&F new door made of 18mm thick prelaminated particle board, exterior gade, one side teak face and white laminated on other side and providing 4mm thick teak wood beading all-round the top all as specified on drawing and directed.

Taking out old U/S side of side board and S&F new side made of 18mm thick prelaminated particle board, exterior grade, one side teak face and white laminated on other side complete all as specified on drawing and directed.

Taking out old U/S back portion ply of side board and S&F of new ply 6mm thick, BWR grade, commercial all as specified on drawing and directed.

Taking out old U/S top board of side board and S&F new top board made of 18mm thick prelaminated particle board, exterior gade, one side teak face and white laminated on other side and providing 3mm thick awood beading all-round the top all as specified on drawing and directed.

Taking out old U/S bottom portion board of side board and S&F of new bottom board made of 18mm thick, prelaminated prarticle board, extrerior garde both face white laminated complete all as specified on drawing and directed.

Taking out old U/S drawer of side board and S&F New drawer to be made of 12mm thick, well seasoned sheesham wood planks and 6mm thick commercial ply at bottom of drawers.

Removing of U/S knob and S&F new knob best quality as per drg and directed by Engineer-in-charge.

HAT STAND WITH MIRROR Drg No. FD-206 & 233

Taking out unserviceable mirror of hat stand and S&F of new mirror, 4mm thick of Make : Atul/Modiguard and fixed complete all as pecified on drawing and directed.

S&F in replacement of new aluminium cap hooks as per existing shape & sixe complete all as specified on drawing and directed.

Taking out unserviceable back portion plywood of hat stand and S&F of new 12mm thick plywood, BWR grade, commercial type complete all as specified on drawing and directed

Removing of old unsv plywood front side of hat stand and and S&F new plywood of hat stand one side teak face 4 mm thick with 4 mm thick teak wood beading all round

Polishing: M&L for preparation of old painting/polishing surfaces by scrubbing existing old polished surface with sand paper, cleaning all dust, filling & stop bore holes with pasty filter prepared by mixing plaster of paris water to a creamy consistence and adding raw in quantity required to obtain the desired colour to the base and to surface allow to been dried up and set aside for 24 hrs for the surfaces to harden rub the surface with sand paper it is thoroughly smooth and dried to receive a coat of acrylic wood finish polish complete all as specified and as directed at site. Make : Berger/Asian/Shalimar.

Chair dining (D-16,203,228 & 279)

Chair Easy ( FD-17,201 & 229)

Chair writing/CBA ( FD-20,202,250 & 280)

Bed Ply wood top/cot newar/bed newar ( FD-213,245,246 & 247)

Table Center ( FD-29,235 & 274)

Table 3'x2' With/Without Drawer ( FD-41,224,231,283 & 284)

Table Peg ( -FD-46,236 & 277)

Table Writing Med,small ( FD-249 & 275 & DB-3902)

Teapoy (FD-232 & 284)

Side board ( FD-26,241 & 371)

Book Case (FD-237)

Table Dressing Ladies ( FD-32,251 & 378)

Table Dressing Gents (FD-31 & 230)

Table Bed Side (FD-28,248 & 276)

Bin soiled linen (FD-244)

Stool dressing (FD-252)

Hat stand ( FD-206 & 233)

Sofa Set 5 Seated/4seater (FD-281)

Table Dining 6/8 Pers

Chair Wooden Bootom

Chair dining Map (FD/E6/MAP/04)

M/s Singh Furniture Mart

Techno India Enterprises