ADDN/ALTN TO BLDG NO P-659 ALONGWITH PROVN OF INTERLOCKING BLOCKS INFRONT OF NO 2 SNCOs MESS AT AF STN BHUJ

Amount

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep for foundation etc or for shafts, wells, cess pits, man holes, pier holes etc n.exc. 10 sqm on plan and n exc 1.50m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing PCC 1:4:8, type D-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass complete all as specified and directed by Engineer-in-Charge.

Material & labour for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulder complete all as specified and directed by Engineer-in-Charge.

Material & labour for 100mm thick PCC type D-2 (1:4:8) using (using 40mm graded stone aggregate) for sub base floor etccomplete all as specified and directed by Engineer-in-Charge.

Material & labour for 75mm thick PCC type C-2 (1:3:6) using (40mm graded stone aggregate) as plinth protection etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of precast concrete block walling built in cement morter complete all as specified and directed by Engineer-in-Charge.

Material & labour for block masonry with precast cement concrete type 1:3:6 (using 20mm graded aggregate) solid bloks exc 10cm inwidth and seting in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in soil complete all as specified and directed by Engineer-in-Charge.

Removal of excavated material (soils) to a distance n.exc 50 mtrs and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed by Engineer-in-Charge.

Taking down existing water proofing tretment on RCC slab / beams with bitumen felt with out damaging structure and removing the debrise outside the MD land and M&L for plaster 10 mm thck on concrete surfaces in cement mortar 1:3 finished even and smooth using WPC @ 3% by weight of cement and preparing the surfaces to recive WPT treatment , applying a coat of bitumenm primer confirm to IS - 3384-1986 @ 3% per sqm . providing APP modified memrane with non woven polyster reinforcement/mat ( centre core) by tourch application over primed surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for cement concete type B-1,1:2:4 mix (using 20 mm grade aggregate) as in roof padding etc finished surface and as in benching of man holes including forming centre channels half round or 1/4 section even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) and removing rubbish off the MD land complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough for laying finishescomplete all as specified and directed by Engineer-in-Charge.

Material & labour for Non skid ceramic colour tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over 15 mm thick screed bed (1:4) etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for 450x350 x7 mm thick glazed ceramic tiles (Digital pattern) including highlighter colored as in dado/ skirting and vertical serfaces set&jointed in neat cement slurry and pointed in colored cement 0ver and incl 10 mm thick cement mortar 1:4 to match the Shade, pattern, laying etc of tiles as directed at site complete all as specified and directed by Engineer-in-Charge.

Material & labour for dark shaded Virified Ceramic Coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in, as in Floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchlaid laid over 15 mm thick screed bed in cm 1:6 etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for dark shaded Virified Ceramic Coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in, as in vertical surfaces such as skirtings, dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchlaid laid over over 10mm thick rendering in cm 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n exc 1.5 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm complete all as specified and directed by Engineer-in-Charge.

Material & labour for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle, 75mm long tower bolt and anodised aluminum fittings such as stay, 75mm long Butt hinges glazing with 5 mm thick tinted sheet glass fixed with Solar control film 25 micron reflective type (gareware sun control or equivalent) and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) complete all as specified and directed by Engineer-in-Charge. .(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately

Supply & fix anodized aluminium ventilator fixed type with frames aluminium section size 63X38X1.20mm thick including fly proofing ventilator fixing with standard rubber gasket locking arrangements aluminium beadings & joining cleats, suitable butt hinges, handle and tower bolts for fixing complete all as specified and 5.5 mm thick tinted glass with Solar control film 25 micron reflective typ complete all as specified and directed by Engineer-in-Charge.

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing and fixiing solid PVC double door frame of size 50mm x 95 mm with a wall thickness of 5 mm, made by jointing 3 Nos, hear bent PVC sheet 'C' channel of 5 mm foam sheet of sizes 35mm x 30mm x 25mm and 40mm x 35 mm x 40mm & 25 mm x 30mm x 35mm using solvent cement. The two side 'C' channel shall be reinforced with 19mm x 19mm MS square tusbe of 19mm gauge. All the three 'C' channel shall be fixed to flat baseof 5 mm PVC sheet with solvent cement. The profile shall be mitre cut at two corners and jointed by inserting 4 Nos. 150mm long brackets of 15 mm x 15mm MS suare tusbe inside the 19mm x 19mm square tubes. The door frame shall be fixed to the wall using 65/100 mm long MS screws throguh the frameby using PVC fasteners. A minimum of 8 Nos of screws to be sprovide for each vertical member & minimum 4 nos for horizontal member etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing & fixing 30mm thick factory made wiremesh solid PVC door shutter consisting of frame made out of 19 gauge thickness & size of 19 mm x 19mm of style and 15mm x 15mm for top, lock and bottom rails. And in addition one veritical member throughout in between styies. MS frame shall be covered with 5mm thick heat moulded PVC 'C' channel of appropriate sixe 15mm wide PVC sheet beading is to be stuck internally in the back side of stiles and ralls of door with solvent cment adhesive. So that the wiremesh can be fixed properly. The wiremesh solid shutter have PVC sheet to match the sutter of PVC moulded shutter etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening complete all as specified and directed by Engineer-in-Charge.

Supply & fix factory made solid panel PVC door shutter S & F 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed by Engineer-in-Charge.

Supply & fix 300mm, brass ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100 mm size mild steel butt hinges, medium weight cold rolled complete all as specified and directed by Engineer-in-Charge.

Supply & fix aluminium anodized pressed handle, fabricated type of size 150mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix 150 mm long aluminium anodized barrel tower bolt complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs 150 mm long aluminium anodized barrel tower bolt complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed by Engineer-in-Charge.

Taking up or down of steel tubing and connections including removal to store for reuse or credit to contractor complete all as specified and as directed by the Engineer-in-Charge of following Sizes:- Note : (a) The rates apply to pipes above or below ground only in repairs and alterations. (b) 'The rates for taking down piping, etc., and removing to store include disconnection of fittings from tubing,where required.

15mm bore

20mm bore

25mm bore

Supply & fix CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge of following Sizes:-

20mm bore

25mm bore

Supply & fix in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge of following Sizes:-

20mm bore

25mm bore

Supply & fix in repairs rotational moulded polythene white water storage tank triple layered (Cylindrical, vertical with closed top, ISI marked) hoisted and fixed in position all as specified in SSR- Part-I of capacity 500 ltrs including taking down existing tank also including provision of 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs rotational moulded polythene white water storage tank triple layered (Cylindrical, vertical with closed top, ISI marked) hoisted and fixed in position all as specified in SSR- Part-I of capacity 750 ltrs including taking down existing tank also including provision of 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron/PVC /AC or reinforced concrete pipes jointed in cement mortar/solvent cement etc. and taking out of from trenches/walls, (including all fittings), with spigot and socket ends and lead joints including burning out joints if required of size 75/100/110mm dia of pipes complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC (SWR) single socketed in any length with rubber ring joints sealed with approved adhesive and fixed on wall with MS brackets or in floor complete all as specified and as directed by the Engineer-in-Charge of following Sizes:-

110mm bore

75mm bore

Supply & fix PVC (SWR) bends any radius of 110 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC (SWR) bends any radius of 75 mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC cowl for 110 mm size pipes, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge.

Material & labour for PVC gully trap 150x110mm,setting and jointing with solvent cement including dismantling of surrounding concrete and fixing of gully trap with and including cement sand mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

Supply & fix grating doom 100mm dia of PTMT (Minimum weight 25gms complete all as specified and directed by Engineer-in-Charge.

Supply & fix 75 mm bore PVC (SWR) floor trap, plain with grating including jointing to waste pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for 15mm bore.bib taps, fancy type, cast copper alloy with crutch handle, chromium plated, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix 15mm bore. bib taps, fancy type, cast copper alloy with crutch handle, chromium plated, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs angle cock / stop valve fancy type 15 mm dia, cast copper alloy, chromium plated, high pressure with crutch handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Supply & fix angle cock / stop valve fancy type 15 mm dia, cast copper alloy, chromium plated, high pressure with crutch handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC connection 450mm long with check nut for wash hand basin/ flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs for pillar taps of 15 mm bore, fancy type with capstan head, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fix pillar taps of 15 mm bore, fancy type with capstan head, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair shower rose chromium plated with swivel joints of size 150mm cast copper alloy CP, fancy type with CP neck 9" long made to shape complete all as specified and directed by Engineer-in-Charge.

Supply & fix shower rose chromium plated with swivel joints of size 150mm cast copper alloy CP, fancy type with CP neck 9" long made to shape complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC flexible waste pipe (heavy duty) 32/40 mm for fixing to WHB/Kitchen sink with long screwed shanks and fly nut flanged complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, white colour, low level with inlet, ball valve, float, Flush pipe of 32 mm dia and handle including brackets incl PVC connection with CP brass nuts on both sides complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, white colour, low level with inlet, ball valve, float, Flush pipe of 32 mm dia and handle including brackets incl PVC connection with CP brass nuts on both sides complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply & fix Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

Supply & fix CP towel rail, 20mm dia, D type,60cm long between flanges complete all as approved complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs vitreous China wash basin white flat back size 550x400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia,PVC flexible wastepipe of adequate length and dia and PVC connection 15mm size 450 mm length with brass CP nuts on both sides complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding, flushing cistern and flush pipe) complete connected to p trapcomplete all as specified and directed by Engineer-in-Charge.

Supply & fix Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge.

Supply & fix toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC shelf wall corner size 230 mm with all fittings/brackets complete all as specified and directed by Engineer-in-Charge.

Supply & fix chromium plated towel ringcomplete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster any description on brick , block or stone walls etc including raking down joints hacking for key secrubing down with water etc any description complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering on concrete surfaces 15mm thick in two layers first coat 15mm thick in CM 1:6 , finished even and fair complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 15mm thick in two layers first coat 10mm thick in CM 1:4 and second coat 5mm thick in CM 1:4 with wate proofing compound @3% by wt of cement on fair faces of brick work or concrete surfaces, finished even and fair complete all as specified and directed by Engineer-in-Charge. Note : WPC will be measured and paid separately..

Material & labour for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:4 for fair finished surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new plastered or unplastered surfaces of walls and applying two coat of distemper oil emulsion over a coat of applying 1mm thick wall care putty ( as approved by GE) complete all as specified and directed by Engineer-in-Charge.

Material & labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over a coat of applying 1mm thick wall care putty and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new plastered or unplastered surfaces of ceiling and applying two coat of distemper oil emulsion over a coat of applying 1mm thick wall care putty ( as approved by GE) complete all as specified and directed by Engineer-in-Charge.

Material & labour for writing letters or figures (block roman) italic or indian not exceeding 30 cm high and 3 cm width in width complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing the rubbish from the work site complete all as specified and as directed by Engineer-in-Charge.

Material & labour for 75mm thick PCC 1:3:6 type C2 (40mm graded agg.) as in road side pavings, plinth protection, etc. finishing even & smooth using extra cement complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Supply & fix pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall and make good to prevent leakage, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Supply & fix roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410- W(Gde- E-250) quality- B complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new or previously untreatedsteel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer on steel surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for anodised aluminium snap grid size of grid 605mm x605mm frame work for fales ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engineer-in-Charge.

Material & labour for perforated particle board for ceiling prepainted , matt finish, 600x600x12mm in size with preparation of approved brand/ make, laid over, grid work ro fixed with nails to any type of frame work or with staples on snap grid incl making niches for fan/light on ceiling purposes complete all as specified and directed by Engineer-in-Charge.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for sand filling under floors or in foundations Spreading and levelling in layers n exc. 25 cm thick , well ramming including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Material & labour for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with gray cement and no pigment in floors complete all as specified and directed by Engineer-in-Charge.

Material & labour for machine pressed precast concrete interlocking paver block with gray cement and pigment, any shape and size confirming to IS-15658-2006 of 60mm thickness, M-35 Grade laid with grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing, cement concrete 1:2:4 type B1 (using 20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep for foundation etc or for shafts, wells, cess pits, man holes, pier holes etc n.exc. 10 sqm on plan and n exc 1.50m in depth and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for plain cement Concrete type C1 1:3:6 (using 20 mm graded stone aggregate) as in coping including necessary form work complete all as specified and directed by Engineer-in-Charge.

Material & labour for PCC 1:3:6 type C-2 (using 20mm graded stone aggregate ) in concrete bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed by Engineer-in-Charge.

Material & labour for 150 mm dia reinforced concrete pipes, class NP 3 with one collar per length of pipe complete all as specified and directed by Engineer-in-Charge.

Material & labour for corrosion resistant TMT bars 10mm dia and over cut to length bent to shape required including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-Charge.

Removing excavated soils exc 1.5 K M and depositing where directed at a level not exc 10 Km above the starting point complete all as specified and directed by Engineer-in-Charge.

Material & labour forproviding, precast cement concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) st in cement mortar 1:6, but in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed by Engineer-in-Charge.

Material & labour for cutting into existing manholes 150mm dia for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed by Engineer-in-Charge.

Material & labour for extra forming fair finished drain or channels of 30cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stopped ends etc complete all as specified and directed by Engineer-in-Charge.

Pulling down the existing U/S wires of any type from concealed wiring carefully of aluminium/copper point wiring (light, fan, bell, socket, power point etc.) with or without conduit, along with all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator etc complete all as specified and directed by Engineer-in-Charge.

Pulling out sub main wiring only any size of aluminium conductor cable PVC insulated with or without condiut complete all as specified and directed by Engineer-in-Charge.

Taking down main switch/DB’s including MCB’s with board and fixture of any description and making good disturbed surface of walls etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through existing conduit including provn of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with new plastic laminated white coloured top sheet cover 3.0 mm thick on existing sunken box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

One 3 pin 5 Amp socket outlet on the same board.

One 3 pin 5 Amps socket out let on independent board.

One bell point controlled by one bell push

All as per item No.103 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps socket out let on independent board complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular plastic flush box of module 3 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular plastic flush box of module 4 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular plastic flush box of module 6 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 1 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 3 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 4 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 6 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fixing including testing of storage type water heater/geyser of vertical type of capacity 10 Ltr, Rated 2000W,230V AC, 50Hz auto cutoff with a high tech adjustable thermostat,multifuction saftey valve,Magnesium anode coated heating element, rust proof external body with unique polymer protective coated inner tank, red and green indicator lamp, suitable for highrise building suitable for water pressure head upto 8 bars star rating (BEE) 5 STAR ,high density & thick PUF that ensures energy efficiency and reduced electricity bills ,15 Amps heavy duty plug complete all as specified and directed by Engineer-in-Charge Note:-The rate quoated shall be in including hanging of geyser in wall with 2/4 nos of stainless steel fastner of suitable size no extra payment will be allowed to contractor in this regard.

Supply & fixing CPVC pipes 20mm dia SDR-11 & plain CPVC SDR-11 with all fittings on wall/ceiling or laying in floor/wall complete with proper steel saddling of half meter apart of each complete all as specified and directed by Engineer-in-Charge

Supply & fixing quarter turn bib cock with flange,fancy type,cast brass with chrome finish crutch or butterfly handle ,screwed down ,screwed for iron pipe/CPVC Pipe or for brass ferrule and fixed for size 15mm bore complete all as specified and directed by Engineer-in-Charge

Supply & fixing quarter turn angle cock with flange 15 mm dia cast brass with chrome finish plate screwed down high pressure,fancy type,with long shank and cup(connected type),screwed both ends for iron pipe/CPVC Pipe complete all as specified and directed by Engineer-in-Charge

Supply & fixing Geyser PVC connection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed by Engineer-in-Charge

Supply & fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct currect motor(BLDC) complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of metal body exhaust fan, AC single phase 230/240V of size 300 mm sweep with louvers including making hole of suitable size/ alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-charge. (Note: Old unserviceable Exhaust Fan will be deposited in MES store yard). .

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor drawn through and including PVC casing caping/conduit medium grade ISI marked with accessories and 4 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge. (Note: Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit)

Supply & fix in replacement energy saving, evironment friendly, long life, corrosion resistent, impact proof, Mini LED building security light made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LEDs with secondary optics and IP 65 protection with LED 20 W light source including material and labour for suitable bracket made of 20 mm dia light grade GI pipe & MS clamps complete with nuts and bolts and washers complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 10 W 2 ft indoor decorative with 2 core copper wire from ceiling rose to light fitting complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 20 W 4 ft indoor decorative with 2 core copper wire from ceiling rose to light fitting complete all as specified and directed by Engr-in-Charge

Supply & fix in replacement double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 triple pole and neutral 4 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 single pole and neutral 8 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of isolators, MCBs, etc. In distribution board of the following rating and capacities complete all as specified and directed by Engineer-in-Charge :-

MCB TPN 415 volts 63 Amps Capacity, 10 KA

MCB SPN of 240 volts 20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Supply & fix in replacement, modular switch flush type, 6 Amp. SP, one way ,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6 Amp, flush type 2 module complete all as specified and directed by Engr-in-Charge

Supply & fix in replacement modular swicth, 16 Amp flush type 1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6/16 Amp flush type 2 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular bell push, flush type, 6 Amp, 1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement call bell multi music type complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of ceiling fan regulator 120 Watt 2 module Modular Type electronic step type 5 step 360 deg complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of ceiling rose 3 phase, PVC/ Polycarbonate body complete all as specified and directed by Engr-in-Charge.

Supply & fixing in replacement of LED Lamp, 7 W ,Type of capacity B22, wide operating Range 140V -280V, Input current 08mA- 30mA, lumen 180-300, UV and IR free light, color temperature 6500K, cool day light, up to 80 % Energy saving over GLS complete all as specified and directed by Engineer-in-Charge

Supply & fix in replacement metal clad enclosure pole and neutral with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps complete all as specified and as directed by Engineer-in-Charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel as shown in electrical plate No.3 of SSR Part-I (2009) complete all as specified and directed including testing on completion including the material and labour complete all as specified and directed by Engineer-in-Charge of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Material & labour for 75mm thick PCC type D-2 (1:4:8) using (using 40mm graded stone aggregate) for sub base floor etccomplete all as specified and directed by Engineer-in-Charge.

Material & labour for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in floor/plinth protection laid to slope 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels finishing exposed edges fair or rounding or chamfering of exposed edges where directed and providing 6mm Joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 or 80/100 gde and three part of sand ( all by weight)complete all as specified and directed by Engr-in-Charge.

MARA CONSTRUCTION CO (BID ID -3098647)

BHAVANI PROVISION STORES (BID ID -3112299)