Main Engine Controls and Auxiliary Engine Controls of MV Vishva Vijetha, on turnkey basis

Amount

ME REMOTE CONTROL SYSTEM AUTOMATION & INSTRUMENTATION

WECS-9520 TO BE CHECKED FOR PROPER FUNCTIOING.

WHILE STARTING M/E ,IT TAKES TOO MUCH AIR WHEN RUNNING ON DIESEL OIL AS COMPARED TO SEA TRIAL REPORT,FAULT TO FIND AND RECTIFY.

ME REMOTE CONTROL SYSTEM AND SAFEGUARD SYSTEM TO BE THOROUGHLY CHECKED.ALL PENUMATIC,ELECTRICAL AND ELECTRONIC COMPONENTS TO SERVICE,DEFECTIVE COMPONENTS TO BE REPAIRED. RENEW THE DEFECTIVE COMPONENTS/MATERIAL SUPPLIED BY CONTRACTOR

ME EXHAUST GAS REMOTE PYROMETERS SYSTEM TO CALIBRATE AND TO PROVE IN WORKING CONDITION.ALSO DEFECTIVE MATERIAL HAS TO BE SUPPLIED AND REPLACED BY THE CONTRACTOR

ME RPM INDICATORS (LOCAL; ECR; BRIDGE AND CEO'S DAY ROOM);TO BE CALIBRATED AND DEFECTIVE MATERIAL TO BE REPLACED BY THE CONTRACTOR

ENGINE TELEGRAPH AND BRIDGE TELEGRAPH TO BE SERVICED .THE DEFECTIVE COMPONENTS/MATERIAL SUPPLIED BY CONTRACTOR

ALL ALARM PANELS TO SERVICE AND RECTIFY ERRATIC ALARM CONDITIONS.TO STIMULATE VARIOUS ALARMS AND PROVE SATISFACTORY INDICATIONS.IF ANY MATERIAL FOUND DEFECTIVE TO BE SUPPLIED BY THE CONTRACTOR

ME JACKET COOLING WATER, LT WATER, LUB OIL TEMPERTAURE CONTROLLERS TO BE SERVICED . ALL TEMPARTURE SENSORS TO SERVICE AND CALIBRATE.DEFECTIVE MATERIAL TO BE SUPPLIED BY THE CONTRACTOR

ME PISTON COOLANT NON FLOW ALARMS FUNCTIONING TO CHECK,ANY DEFECT TO RECTIFY.THE REQUIRED MATERIAL TO BE SUPPLIED AND RENEWED BY THE CONTRACTOR

ME TURBOCHARGER OIL NON FLOW ALARMS FUNCTIOING TO CHECK,ANY DEFECT TO RECTIFY.THE REQUIRED MATERIAL TO BE SUPPLIED AND RENEWED BY THE CONTRACTOR

ME CRANKCASE OIL MIST DETECTOR (GRAVINIER MK6) TO BE SERVICED AND TO CHECK SENSITIVITY AND ZERO SETTING ALL SAMPLING TUBES TO CLEAN.OIL MIST DETECTOR TO BE SATISFACTORILY SURVEYED BY CLASS SURVEYORS.THE REQUIRED MATERIAL TO BE SUPPLIED AND RENEWED BY THE CONTRACTOR

ME FUEL OIL VISCOSITY CONTROLLER TO BE SERVICED AND CALIBRATED. IF DEFECTIVE SAME TO RECTIFIED AND REQUIRED MATERIAL TO BE SUPPLIED BY CONTRACTOR

PRESSURE SWITCHES FOR AUTO STARTING OF ESSENTIAL PUMPS MOTORS TO SERVICE,DEFECTIVE ONES TO RENEW/REPAIR,SATISFACTORY TRIALS TO BE SHOWN TO ELO/CEO.MATERIAL REQUIRED FOR PROVING OF THE SYSTEM TO BE SUPPLIED BY THE CONTRACTOR.

ME CRANK ANGLE SENSOR BELT TO BE REPLACED AS PER MAKER INSTRUCTION MANUAL YARD HAS TO ARRANGE WARTSILA SERVCIE ENGINEER FOR JOBS.DRIVE TO BE OVERHAULED.BELT AND SPARES SHIP SUPPLY.CRANK ANGLE SENSOR TO BE ADJUSTED.MATERIAL REQUIRED FOR PROVING OF THE SYSTEM TO BE SUPPLIED BY THE CONTRACTOR.

A COMPLETE OVERHAUL OF ME PNEUMATIC LOGIC BOX AT BOTTOM PLATFORM REQUIRED.MATERIAL REQUIRED FOR PROVING OF THE SYSTEM TO BE SUPPLIED BY THE CONTRACTOR.

ALARM MONITOTRING SYSTEM & WECS SOFTWARE/HARDWARE TO BE UPDATED AND NOTICE DEFECT TO BE RECTIFIED.

E21029 ITEM : AUXILIARY ENGINE AUTOMATION & INSTRUMENTATION

TO CHECK & SERVICE AUXILIARY ENGINE CONTROL SYSTEM FOR AUTOMATION SEQUENCE OF AUTO STAND BY,AUTO START,AUTO LOADING & AUTO STOP.THE SYSTEM HAS TO BE THROUGHLY CHECKED AND FAULTS TO BE RECTIFIED.MATERIAL REQUIRED FOR PROVING OF THE SYSTEM INCLUDING BOOSTER RELAYS TO BE SUPPLIED BY THE CONTRACTOR

TO OVERHAUL MAIN STARTING VALVE,STARTING MOTOR,EMERGENCY STARTING VALVE,STOP CYLINDER AND OVER SPEED DEVICE.MATERIAL REQUIRED FOR PROVING OF THE SYSTEM TO BE SUPPLIED BY THE CONTRACTOR.

FOR ALL THREE A.E.S TO CHECK AND CALIBERATE ALL IMPORTANT PRESSURE GAUGES,REMOTE TEMPERATURE GAUGES, PRESSURE TRANSMITTERS AND TACHOMETERS.CALIBERATION CERTIFICATES TO BE ISSUED.DEFECTIVE MATERIAL TO BE RENEWED BY THE CONTRACTOR

THE FOLLOWING ALARMS AND TRIPS OF ALL THREE A.E'S ARE TO BE CALIBRATED AND SET POINT TO BE ADJUSTED AS PER THE OEM MANUAL.CALIBRATION REPORT TO BE SUBMITTED FOR THE CALIBRATED EQUIPMENTS AND THE REQUIRED MATERIAL HAS TO BE SUPPLIED BY THE CONTRACTOR FOR PROVING OF THE SYSTEM

a)C.W. INLET LOW PRESSURE ALARM

b)L.O.INLET LOW PRESS

c)C.W. HIGH TEMP.ALARM

d)L.O.INLET HIGH TEMP

e) EXHAUST GAS HIGH TEMP

f)OVER SPEED

ALL THREE A/E LOCAL START FROM PANEL TO BE MADE OPERATIONAL.

Following E/R temperature and pressure gauges, ECR Console gauges on various machineries are to be calibrated by removing and refitment back the existing guage with the standard gauge. Calibration certificates are to be issued to the gauges and the same are to be valid for a period of one year from calibrated date. Calibrate the gauges, temperature and pressure gauges.The Gauges found defective during calibration are to be renewed by the contractor of same material, size and range with glycerin filled. PYROMETERS/THERMOMETERS, SYSTEM / /RANGE (Deg C)

M/E EXHAUST GAS OULET 0-600

M/E TURBOCHARGER IN/OULET 0-600

M/E AIR COOLER AIR IN/OULET 0-100/0-160

M/E TURBOCHARGER C.WOULET 0-100

A/E EXH GAS OULLET(3 AES) 0-500

A/E TURBOCHARGER INLET(3 AES) 0-600

A/E TURBOCHARGER OULET(3 AES) 0-600

A/ES C.W. INLET 0-100

A/ES C.W. OULET 0-100

A/ES AIR COOLER AIR INLET 0-200

A/ES AIR COOLER AIR OULT 0-100

A/ES ALTERNATOR BEARING 0-100

BOILER F.O HEATER IN/OULET 0-160

ME VISCOTHERM 0-200

ME LUB OIL COOLER L.O IN/OUT 0-100

ME JACKET COOLER L.O IN/OUT 0-100

ME THRUST BEARING LUB OIL 0-101

ECR TEMP.GAUGES

ME L.O INLET TEMP 0-100

ME T/C BEARING OIL TEMP 0-150

ME F.O. TEMP 0-200

ME FRESH COOL WATER INLET 0-150

FWD S/T BRG L.O.TEMP 0-100

AFT S/T BRG L.O.TEMP 0-100

A/E PUF UNIT OUTLET TEMP 0-101

PRESSURE GAUGES, / SYSTEM RANGE (BAR)

STEERING GEAR 0-250

AIR COMPRESSORS 0-10

AIR RECEIVER(MAIN) 0-50

AIR RECEIVER(CONTROL) 0-15

AUX.ENGINE 0-10

AUX.ENGINE 0-16

ME L.O.P/P DEL. 0-10

ME ST.BY CONT AND SAFETY AIR 0-16

ME EXH V/V SPRING(ECR & LOCAL) 0-10

ME F.O.& L.O. AT EM STAND 0-25

ME FUEL V/V TESTING UNIT 0-600

VIBRATION DAMPER 0-250

EXH.GAS ECONOMIZER 0-16

AE FUEL V/V TESTING UNIT P/P 0-500

HYD P/P FOR MAINTENANCE 0-1000

BUNKER LINE PRESSURE GAUGES 0-17

ECR PRESSURE GAUGES:-

ME COOL S.W.DISCH.PR 0-4

ME JCW COOLING PR 0-6

ME LO INLET PR 0-6

ME SCAVENGE AIR PR 0-6

STARTING AIR BEFORE V/V PR 0-40

CONTROL AIR PR 0-6

STARTING AIR AFTER V/V PR 0-40

CHARGE AIR 0-4

ME AIR RECEIVER 0-40

CONTROL AIR RECEIVER 0-10

EXH V/V AIR SPRING 0-10

BLR DRUM PR 0-11

MANOEUVRING PLATFORM

AIR SPRING 0-10

CYL/COOLING WATER 0-6

STARTING AIR 0-40

SUPERCHARGE AIR 0-4

COOLING WATER AIR COOLER 0-10

MAIN S.W. P/P SUC -1-5

MAIN S.W. P/P DISCH 0-10

BALLAST P/P SUC -1-7

BALLAST P/P DISCH 1-9

FIRE & G.S. P/P SUC -1-5

FIRE & G.S. P/P DISCH 0-10

BILGE & G.S. P/P SUC -1-5

BILGE & G.S. P/P DISCH 0-10

AKSHAY CONTROLS AND SYSTEMS PVT. LTD.