SPL REPAIR TO BLDG NO T/PFS-93 (ORS LIVING) AND SPL REPAIR TO 753 OFFICE COMPLEX AND T/OPS-98 AND 99 OF 98 ARTY BDE SIG COY AT MIL STN GANDHIDHAM UNDER GE ARMY BHUJ

Amount

Taking down cement plaster of any description from brick wall or concrete surfaces including racking out joints and hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for 15 mm thick in two layer of plaster in CM (1:6) on brick work / RCC concrete surfaces of wall and finish the external surface even and smooth without using extra cement complete all as specified and directed. Note :- Water proofing compound shall be measured and paid for seperately under appropriate item of Sch "A' as supply only complete all as specified and directed

Supply only Liquid water proofing compound complete all as specified and directed.

M & L for preparation of newly plastered wall surfaces and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L for rendering 10 mm thick in CM (1:4) on fair faces of brick work on concrete surfaces/stone masonary and finishing the internal surface even and smooth without using extra cement complete all as specified and directed.

Complete removal of existing treatment on wall (any number of layers) by scarping with steel scrapers or any other mean including filling depressions of scrapped surface with putty and Providing and applying 3mm thick wall care putty on wall to prepare the surface even and smooth. and Material and labour for two coats of distemper oil emulsion white or tinted including priming plastered and other surfaces with alkali resistant priming paint complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons,dados etc laid, bedded and pointed in any mortar and removal of rubbish off the site complete all as specified & as directed.

M & L for coloured joint free non skid tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm for vertical surface (dado) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for Anodised aluminium snap grid having Size of grid 605 x 605mm frame work for false ceiling all as specified complete all as specified and directed.

S & F for powder coated aluminium door, window and ventilator frame and shutters, side hung type without sash bars, aluminium sections weightings 0.55kg/Rm including necessary joining cleats glazing clips, ruber neoprene packing, anodised aluminiumsnap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 NOs). hinges type B-21 100mm long (2NOs) suitable handle (1NOs) with 5mm thick sheet glass, Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wireepairs 50 micron coloured powder coated aluminium decorative grill design No DG-117,10 mm thick staples complete all as specified and directed..

S & F for Powder Coated aluminium frame for partitions with 5.50 mm thick sheet glass as in panes one or more rebates including joining cleat for fixing and 12 mm particle board for insulation purposes, fixed with nails to timber/ aluminum frame work complete all as specified and directed.

M&L Pressed steel frames for doors of size 105x 60mm for door with Double rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified,and as directed.

S & F of 30 mm thick flush shutter, solid core construction,with block board core and plywood face panel, commercial type on both sides complete all as specified and directed.

S & F in repairs to Harrison rails, (curtains rods) anodised aluminium alloy, powder coated with fixing brackets, stops, rollers etc complete all as specified and directed.

Demolition of precast concrete block walling and similar items i.e. ashlar facing dressing stone work, precast concrete articles etc of any description and in any position built in cement mortar including all quoins, arches and pillars etc and disposing off rubbish) off the premises of cantonment complete all as specified and directed.

M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in Modular bricks in cement mortar 1:6 including curing,racking of joints etc.complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for PCC Type B2, 1:2:4 using 40mm graded stone aggt as in base of floor 100mm thick complete all as specified and directed.

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors/ paving/plinth not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

M & L for cement concrete type C-2, 1:3:6 (40mm graded aggregate), 75mm thick. as in plinth protection finished even and smooth without using extra cement including expansion joints complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways complete all as specified and directed.

M & L for 100 mm thick PCC 1:3:6 type C-2 (40 mm graded stone aggregate) as in sub base and all other similar works complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Preparation of new or previously untreated surfaces of concrete and concrete based materials of any description and in any position over 10 cm width or girth and Material and labour for applying two coat of synthetic enamel paint on concrete surfaces over priming paint plaster coats complete all as specified and directed.

Demolition of ceiling boards of any description, and any thickness including cover fillets and frame work complete all as specified and directed.

M & L for powder coated aluminium snap grid having a size of 605mm x 605mm and sections incorporated in frame work shall conform to IS 733, IS 737 and IS 1285 and snap grid frame work shall be fixed to ceiling with supporting hanger 6mm dia mild steel rod, J bolts with necessary bolts, nuts and washers all as per manufacturer's instruction. The main & cross tees shall be jointed at junction/crossings with anodized aluminum angle bracket of size 19.05mm x 19.05mm x 1.45mm, weighing 0.14 Kg per RM, fixed with suitable mild steel, bolts nuts and washer all as per manufacturer's instruction, the snap grid shall be supported at ends all along the wall with anodized aluminum angle of size 38mm x 25mm x 2.18mm, weighing 0.358 Kg per running meter complete all as specified and directed.

S & F of 9mm thick PVC laminated gypsum ceiling tiles size of 600mm x 600mm, square edge, front side laminated PVC and back side aluminium foil complete all as specified and directed. (Frame work for ceiling shall be measured and paid separately).

Taking down of Wall panelling and similar work complete all as specified and directed.

S & F of Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S & F of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and rubbish off the primises complete all as directed.

M & L for 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes like tiles etc complete all as specified and directed.

M & L for coloured joint free Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for coloured non skid digital ceramic joint less tiles 7 to 10 mm thick (square/rectangular) are of each tile exc 0.18 Sqm but n. Exc. 0.38 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement for dado/skirting to match complete all as specified and directed.

Material & labour for glazed ceramic coloured tiles (300mmx450mm, on vertical surface such as skirtings/dados set and jointed in neat cement slurry and pointed in coloured cement to match and incl.10mm thick backing coat in CM 1:4 finished even and fair complete all as specified.

Taking up or down steel tubing / CPVC Pipes and connection including cleaning for refixing or removed to store complete all as specified and directed.

(a) 16 mm bore

(b) 20 mm bore

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified & directed of following OUTER DIAMETER sizes :-

(a) 20 mm bore

(b) 25 mm bore

Taking down of chowkhats / frames n exc 1.50 sqm each without taking off shutter each complete all as specified and directed.

Taking down of chowkhats / frames exc 1.50 Sqm but n exc 4.0 sqm each without taking off shutter each complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed.

Providing and fixing Powder coated Anodised Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified and directed.

Providing and fixing Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed.

S & F of 5.5mm thick Sheet glass, ordinary quality and glazing sheet glass is ground or obscured or frosted, on one side with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profiles reinforced with 19 x 19mm MS square tube provided with EPDM rubber gasket weather seal through out the frame and the profile mitre cut at two corners and joined by inserting 2 nos 150mm long brackets of 15 x 15mm MS square tube inside 19 x 19mm MS square tube suitably screwed complete all as specified and directed.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes of size 15 x 15mm for top and bottom rails and 19 x 19mm for stiles, MS frame covered with 5mm thick single piece extruded PVC profile 'C' channel having a 5mm thick PVC sheet strip of 20mm width struck inside with solvent cement, forming stiles, and 5mm thick single piece extruded PVC profile for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail; panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc all as per manufacturer's instructions and drawings as shown in SSR Part-I 2009 complete all as specified and directed.

S & F of Factory made wire gauzed PVC door shutter 30 mm thick, i.e. panel will be of wire gauzed in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet and PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 Deg) used instead of exposed portion of PVC sheet beading. suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F of aluminium anodised 200 mm barrel tower bolts of extruded section complete all as specified and directed. 8 door x 2 tower x 2 skeleton

S & F of 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F of 100 mm butt hinges extruded aluminium alloy with galvanized mild steel hinges pin anodised type `C'-22 complete all as specified and directed.

S & F of mild steel 300 mm, ordinary rat tail rod pattern springs, including roler and roller plate complete all as specified and directed.

S & F of 300mm long aluminium alloy, anodised sliding door bolt with haps, staple(bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

M & L of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover,governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S & F in repairs of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F of 75 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S & F in repairs for floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140 mm, complete all as specified and directed.

M & L for preparation of old wooden surfaces of any description, not otherwise described,over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary paint tint) (each coat) over a coat of pink primer including scafoldings of any hieght complete all as specified and directed.

S & F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete all as specified and directed.

S & F in repair PVC connection 15mm size PTMT nuts of length 450 mm complete all as specified and directed.

S & F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repair of two way angle cock chromium plated fancy type 15 mm bore complete all as specified and directed.

S & F in repair of two way bib cock chromium plated fancy type 15 mm bore complete all as specified and directed.

S & F in repairs to health faucet with 1200 mm long flexible mild steel tube 80 mm dia with wall hook complete all as specified and directed.

S & F in repairs acrylic shelf having size of 56 cms x 13 cms with chromium plated bracket below WHB mirror complete all as specified and directed.

S & F as in repair grating round 150mm size of PTMT (minimum 100 gms) with waste hole of PTMT complete all as specified and directed.

S & F in repair 15 mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type, high pressure, with or without and fly nuts complete all as specified and directed.

S & F in repairs Tubular towel rail, 20mm dia, D type, 60cm long between flanges brass chromium plated complete all as specified and directed.

S & F in repairs CP Toilet Paper holder all as per cat part complete all as specified and directed.

Demolition and breaking up drain pipes upto 100/110 mm dia (Salt glazed ware, AC, PVC or reinforced concrete) set in cement mortar complete all as specified and directed

Supply and fixing of PVC (SWR) WC connector bent type for 110mm bore PVC pipes complete all as specified and as directed.

Supply and fixing of PVC (SWR) for 75mm Diameter of outlet floor trap, plain with grating including jointing with solvent cement etc complete all as specified and as directed.

Supply and fixing of PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed.

S & F in repairs 50 micron coloured powder coated aluminium decorative grill design No DG-117,10 mm thick including F Sections complete all as specified and directed.

S & F in repairs aluminium (extruded section) body door closer hydraulically regulated designation No 3, universal type,suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 kg complete all as specified and directed.

S & F in repairs to Harrison rails (Curtain Rails / Rod), anodised aluminium alloy, powder coated with fixing brackets, stops, rollers etc rate inclusive of brackets as per requirement complete all as specified and directed.(27wx2m)

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3.0mtr in length. Exposed surfaces finished even and smooth with using extra cement including racking out joints between pannel to pannel and pannel to wall and plugging the same with bitumunius mastic using bitumen and mixure in 1:3 complete all as specified and directed.

M & L for Powder coated aluminium(minimum thickness of powdercoating 50 micron) work for doors,windows, ventilators andpartitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.

Taking down cement plaster on brick/stone walls etc including raking out joint, hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L 15 mm thick rendering in two layers (first coat 10mm thick in cement mortar 1:6 and second 5mm thick in cement mortar 1:4 on external surfaces of walls & top surfaces of chajja/roof/ceiling mixed with and including liquid water proofing compound as per manufacturers' instruction surface finished fair and evencomplete all as specified and directed.. (Note - Liquid water proofing compound separately)

M&L two coats cement base paint white or tinted on walls etc. complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

M&L two coat of synthetic enamel pinting over a coat of red oxide primer incl preparation of old steel surface over 10 cm width or girth complete all as specified and directed.

Dismantling & taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down old and unsrevicable sheet metal enclosure , switch fuse unit , distribution bord any type /way / capacity including fuses,MCB's , insulator etc complete after removing all connection and making good the disturbed surface complete all as specified and directed.

M&L in repair for Point wiring complete with FR PVC insulated unsheathed , 1100 V grade conforming to IS 694 , 1.5 Sqmm (Norminal area) multistranded ,copper conductor cable drawn through in non metallic rigid PVC surface casing caping grade with sutaible size of 1 to 8 module metal flush boxes and back plate for mounting of modular switches/socket and regulators and including modular fornt plate with all accessories complete all as specified and directed.

(a) One light point controlled by one way one switch SP 5 Amps ,240 V complete all as specified and directed.

(b) One ceiling/exhaust fan point controlled by one way one switch SP 5 Amps, 240 V complete all as specified and directed.

(c) One switch socket outlet 3 Pin, 6 Amps, SP on independent board complete all as specified and directed.

All as per Sl item No 86 above but for one socket outlet point on the same baord with other switches complete all as specified and directed.

All as per the above item No 87 herein before but with 2.5 Sqmm cable for 3 Pin 5/15 Amps switch socket outlet complete all as specified and directed.

S&F in repair modular switch one way 6 Amps , 1 module type complete all as specified and directed.

S&F in repair modular switch 1 way 16A, 1 module of one way complete all as specified and as directed.

S&F in repair modular socket , 6 Amps , 2/3 pin combined 2 module type complete all as specified and directed.

S&F in repair modular switch socket combination, 6 Amps / 16 Amps , 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked complete all as specified and directed.

S & F in replacement elegantly industrial general purpose box type luminaire, 1x20 Watt, designed box type LED luminaries, CRCA sheet steel housing with white reflector cover fitted to the body with decorative end covers complete with electronic ballast, spring loaded rotor type lamp holders, connected block with and including 01 No LED lamp 20 Watt and all accessories, pre-wired and connecting the same to ceiling rose with & including twin core PVC insulated and sheathed copper conductor 23/0.0076 cable including all accessories and fixing arrangement for fixing the light fitting to walls / roof surface over and including 2 Nos PVC square box complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing ceiling fans complete with three blades, down rods, regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with squirrel cage induction motorcomplete all as specified and directed. (Note : Old ceiling Fan to be deposited in MES store yard for repair)

Supply & Fixing LED street/bldg light fitting luminaire 35 Watt IP-65/66, 230 volts, new generation energy saving & enviormental friendly long life versatile pressure die cast aluminium roadway luminarie with high power LEDs as light source and electronic driver alongwith suitable bracket required as per site for fixing the light complete all as specified & directed.

M&L for sub main wiring with two runs of 4 Sqmm (2x4 sqmm )1100 volts grade single core FR PVC insulated unsheathed multistranded copper conductorcable confirming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories concealed in walls/roofs/floors etc with one run of 2.5 Sqmm (1x2.5sqmm ) single core FR PVC insulated unsheathed copper conductor cable as earth wire complete all as specified and directed. (Note:- 2 runs of 4 Sqmm ,one run of 2.5 Sqmm ( 2x4 sqmm + 1x2.5 sqmm ) cable and one meter of conduit will be measured as one unit again.)

S&F sheet metal enclosures for distribution board when MCB to be used SPN ( Single epole and neutral ) 08 way, 240 Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed.

S&F MCB SPN, 6 to 32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series complete all as specified and directed.

S&F MCB SP, 6 to 32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series complete all as specified and directed.

M&L , earthing complete for machinary / Equipment installed at power house / sub station with galavanised steel earth plate electrode of size 60 cmx 60 cmx 6 mm thick buried directly in ground ( earth pit not less then 2.25 m deep below the normal ground level ) with top edge of the earth plate not less then 1.5m below normal Ground level connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washerws and check nuts all shown in electrical plate No.5 of SSR Part- I connected to main board / disribution board complete .Earthing GI lead and GI protection pipe 15 mm dia light grade upto 7.5 m from earth pit connecting to machinary/ equipment, testing point, all as specified and testing on completion all as per directed.

Note :- (i) The unit rate shall also included for earth work in hard /dense soil , PCC type C-I (1:3:6) chamber , PCC 1:2:4 type B-I cover 50 mm thick reinforced with 8 mm dia TMT bars,150 mm c/c both ways, funnel with watering pipe 20 mm dia medium graded , GI protection pipe light grade 15 mm dia and wire mesh complete in addition to items No. 1(a) to (e) of preamble (notes) under sub heading earthing specified on SI page No. 389 of SSR Part - II.

(ii) Earthing lead and GI protection pipe beyond 7.5 mtrs will be measured and paid separatelly if required under appropriate Schedule.

Note :- (i) Earthing shall be tested as specified in casul 19.137 of SSP PART - I 2009 , to the entire satisfication of Engr-in-Charge. (ii) On teting after complataion of earthing , if the desired earth resistance is not obatined the earthing wiil be re done by the contractor at his on risk and cost to the entire satisfaction of the Engr - in - charge.

Supplying , laying , passing through pipe , connecting and testing UG cable XLPE insulated ,armoured heavy duty electric cable with aluminium conductor ,1100 volts grade of size 16 Sqmm 4 core complete all as specified and directed.

Excavation in trenches in soft/loose soil , not.exc 1.5 mtr wide and not.exc 1.5 mtr deep and getting out in soft/loose soil for laying of cable/foundation of pole and stay etc complete all as specified and directed.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

Removing excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above ground level from starting point complete all as specified and directed.

M&L for sand cushioning in trenches for protection of LT under ground cable including watering and consolidation complete all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover class LV Type 1, flat, size 250mm x 150mm x 40mm complete all as specified and directed.

Supply and laying GI tube light grade 25 mm bore complete all as specified and directed.

S&F Modular switch socket outlet 3 pin 5 Amp' flush type controlled by one switch , complete all as specified and directed.

S&F Modular switch socket outlet 3 pin, 15Amp, flush type, complete all as specified and as directed.

S & FCeiling rose, Pilot 3 Plate ceiling rose 6A ,complete all as specified and as directed.

S&F Modular Fan step regulator, 120W complete all as specified and as directed.

Supply and fixing in repair LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to light fittings complete all as specified and directed.

S&F Lamp Holder PVC/ polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED bulb 14 watt complete all as specified and directed.

S&F distribution box epoxy powder coated, SPN 8 way, 240 V, with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door as in replacment ,complete all as specified and directed.

S &F MCB SP 6 to 32 Amps, 240 Volts of 'B' series to be housed in DBs and suitable size cable lugs to be fixed with MCBs as in replacment, complete all as specified and directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete all as specified and directed.

Disconnecting and taking out old existing steel/PVC tubing and connections of any description/ grade and in any position in trenches/under floors / on walls etc including all fittings/accessories and fixtures such as bends, union, elbow socket, valves, taps etc, all as directed and specified for 25 mm dia pipe complete all as specified and directed. Note :- Excavation & earth work shall be measured and paid for separately under respective item of Sch 'A'.

Supply and Fixing in any length UPVC pipe 25 mm dia pipe manufactured as per ASTM-D-1785 as per IS-559, Schedule-40 complete with all fittings,connections, laid in trenches/wall in required length complete all as specified and directed

S & F in repair UPVC Ball valves with operating handle (stop valve) of size 25 mm dia complete suitable for fittings with ASTM - 1785, Schedule 40 UPVC pipes complete all as specified and directed.

Cutting existing steel/ UPVC tubing of any size for alterations, additions or insertions of new GI/CI/ UPVC pipe of size 25mm dia complete all as specified and directed.

Supplying ,Laying , jointing and testing XLPE insulated, armoured, heavy duty, LT aluminum conductor cable 1100 volts grade of size 10 Sqmm, 2 core laid in trenches/ducts, floors, fixed to walls etc complete all as specified and directed.

Material and labour for dry clean river sand for cushioning of cable in trenches for cable protection including spreading, leveling and hand punning complete all as specified in SSR Part-I and as directed. Note :- Only compacted thickness of sand will be measured and paid separately.

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type 1, flat as per size 250mm x 150mm x 40mm for LT cable and laid dry in trenches over underground cables complete all as specified and directed

NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.

M/S S. SINGH TRADERS (BID ID -3459854)