REPAIRS TO ROOFS SUNKEN JOINERY SANITARY FITTINGS AND MISC REPAIRS OF CERTAIN BUILDINGS IN TECHNICAL AREA ZONE-II AT AF STN BHUJ

Amount

Taking down existing water proofing tretment on RCC slab / beams with bitumen felt without damaging structure and removing the debrise outside the MD land and M&L for plaster 15 mm thck on concrete surfaces in cement mortar 1:4 finished even and smooth using WPC @ 3% by weight of cement and preparing the surfaces to recive WPT treatment , applying a coat of bitumenm primer confirm to IS - 3384-1986 @ 0.3 litre per Sqm. providing 3 mm thick APP modified memrane with non woven polyster reinforcement/mat ( centre core) by tourch application over primed surfaces all as specified and directed by Engr-In- Charge

S&F in repairs sink with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 x 460 mm, bowl size 410 x 330 x 180 mm mm Make : Nirali (Model : elegance small from regular range, glossy) or size 915 mm x 460 mm bowl size 410 x 330 x 178 mm of make : Jayana (Model : Jujpiter sink with Drain board No: SBSD 5 glossy) or equivalent and nearest size of make : Lorrentto, Neelkanth, Diamond.

Demolition of cement concrete (un reinforced ) in ground floors and pavings n.exc 15cm thick (below or above ground level ) all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

M&L for 25mm thick cement concrete type B-0 1:2:4 using 12.5mm graded aggregate in floors complete.

M&L for Vitrified ceramic polished light shade tiles 10mm thick area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM-1:6 complete all as specified.

All as per Ser Item No 7 above but in vertical surfaces such as dado, skirtingand riser etc all as directed by the EIC.(NOTE:- including Backing coat of tiles 10mm thick CM (1:4) )

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over including screed bed 15mm thick in CM-1:6 complete all as specified.

All as per Ser Item No 6 above but in vertical surfaces such as dado, skirtingand riser laid over and including backing coat 10mm thick in cement plaster 1:4 all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM-1:6 complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and icluding plaster in CM 1:4 all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n.exc 1.5 sqm

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm each.

Taking down shutters of any description exc 1.0 sqm but n.exc 2.00 sqm each.

Taking down of shutters of any description of size exc 2.0 Sqm each, complete all as specified and as directed by the EIC.

Re- fixing of shutters in same opening of size exc 1.0 sqm but n.exc 2.00 sqm each.

Re- fixing of shutters of in same opening any description of size exc 2.0 Sqm each, complete all as specified and as directed by the EIC.

S&F 125x60mm,1.25mm thick pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specifiedincluding filling in frames with cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) all as directed by Engr-in charge

S&F 105x60mm,1.25mm thick pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified including filling in frames with cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) all as directed by Engr-in charge

M&L for cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in bed blocks for fixing of hold fasts and the like including necessary formwork all as directed by Engr-in charge

M&L for Preparaing surfaces of steel and steel based materials, and iron work of small articles such as hold fasts, ends of posts, backs of chowkats etc and treated with tar or coal tar black paint, area tarred n exc 0.1Sqm each.

M&L for Preparing surfaces of steel and steel based materials, and iron work of small articles such as hold fasts, ends of posts, backs of chowkats etc and treated with tar or coal tar black paint, area tarred exc 0.1 Sqm but n. exc. 0.5 Sqm each.

S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/ Gauge etc. Size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete.

S&F 35mm thick 2nd class hard wood factory made plain framed, paneled shutters (any number of panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veveered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated..

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed wih aluminium wire staples.

S&F 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cost or extraded sections and fixing bolts and sliding bolts of extraded sections or cost aluminium alloy.

S&F100mm size of hinges butt hinges, medium weight, cold rolled mild steel.

S&F 150mm size extruded aluminium alloy handles, fabricated type.

S&F 150 mm size aluminium, anodised barrel tower bolt of extruded section.

S&F for 140mm floor door stopper of aluminium alloy body and tongue, anodised, fixed in floors.

S&F in repairs 300mm mild steel ,ordinary rat tail rod pattern springs including roller and roller plate complete fixed in doors.

M&L for preparation of new sufaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engr-in-Charge

M&L for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out of JINDAL/ INDAL anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) all as specified and directed.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm

Supply , fabricate & fix anodised (15 micron) aluminium sliding windows/ ventilators made out of Jindal/Hindalco Aluminium sections as in frames , sliding/ fixed shutters etc. With one or more rebates incl. Jointing cleats & locking arrangements complete all as specified & as per manufacturer's instruction. Note- Quoted rate shall deemed to be included for supply of aluminium sections, fabricate & fixing in position of window frames & shutters, locking arrangements complete.

S&F rubber beading for fixing of glass of item No 37.00 above complete.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih stainless steel wire staples.

Taking up or down following size of steel tubing and connections.

15mm bore of pipe

20mm bore of pipe

25mm bore of pipe

S&F CPVCpipes ISI marked IS 157778 with all fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors of following sizes ( SDR 13.5 of make:- astral or equivalent of supreme / finolex )

20mm bore of pipe

25mm bore of pipe

32mm bore of pipe

S&F in repairs fancy type bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for size 15mm bore.

S&Fin repair stop valve 15 mm dia cast chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed.

dittoas per above item but concealed type

S&F repair for shower rose for 15 mm dia cast chromium plated screwed down high pressure with long shunk screwed end for iron pipe or for unions

S&F in repairs vitreous china wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets.

S&Fin repair pillar taps of 15 mm bore, fancy type with capstan head, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe & fixed.

S&F in repairs Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed

S&F in repairs soap dish any type fixed to plugs with chromium plated brass screws.

S&F in repairs Aluminium anodised tubular towel rail 20mm dia D Type 60cm long between flanges

S&F Vitrious china squattin pan ,Orrissa Paattern Size 580x440 mm white with integral foot rests ( Excluding flushing cistern and flush pipe)

S&F cast iron 'P' or 'S' traps 100 mm bore of pipe.

S/F grating square 150mm size of PTMT (minimum weight 100 gms )

S&F in repairs PVC low level valveless, syphonic action type flushing cistern, low level, white, with inlet, bll valve, flaot and handle including brackets of 10 Ltr capacity.

M&L for PVC (SWR ) gully trap 125/110mm, setting and jointing with solvent cement .all as directed by Engr-in-charge

M&L for 75mm dia cast iron floor trap with grating incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4 )

M&L for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces.

M&L for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:6 and finished even and smooth without using extra cement as specified.

M&L for preparing new plastered ceiling/soffits of chajjas surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on ceiling surfaces and applying two coats of white wash by finishing the surfaces even and smooth complete all as specified and directed by EIC.

M&L for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion, white or tinted including one coat of wall care Putty by finishing the surfaces even and smooth complete all as specified and directed by EIC.

Complete removal of existing treatment on wall surfaces and applying two coats of distemper with distemper oil emuision, white or tinted including one coat of wall care putty by finishing the surfaces even and smooth complete all as specified and directed by EIC.

Dismantling of cast iron,PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required all as directed by Engr-in-charge following bore of pipe

110mm dia of pipe

75mm dia of pipe

S&F of PVC drain self it pipes, single sockets ISI marked IS 13592 type 'B' in any length, jointed with solvent cement fixed in walls and the dia of pipes ( make :- Astral type 'B' pipes or equivalent)

110mm dia of pipe

75mm dia of pipe

S&F of PVC junction single 'Tee' ISI marked IS 14735 jointed with solvent cement fixed in walls and the dia of pipes ( make :- Astral type 'B' pipes or equivalent)

110mm dia of pipe

75mm dia of pipe

S&F of PVC bend equal ISI marked IS 14735 jointed with solvent cement fixed in walls and the dia of pipes ( make :- Astral type 'B' pipes or equivalent)

110mm dia of pipe

75mm dia of pipe

Supply and fixing in repairs Rotational moulded polythelene water storage tank, three layered, ISI marked, cylindrical vertical with closed top including dismantling existing water tank and removingto store of following capacity (Make - Sintex / Euro / Cera) : -

1000 litres capacity

750 litres capacity

500 litres capacity

M&L for 75 mm thick cement concrete type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base under interlocking tiles complete all as specified and directed.

M&L 60 mm thick (M-35 mix) glossy rubber mould interlocking tiles (paver blocks red & yellow colour topping) conforming to IS-15658-2006 laid dry over and including 30 mm copacted sand bed, size & pattern of tiles all as directed by Engineer-in-Charge. Make: Lucky Cement Works or equivalent as approved by GE.

S&F PVC/PTMT shelf fixed to walls with screws including necessary drilling holes. Make : Prayag cat No 190-C or equivalent of polytuf / pearl all as directed by Engr-in charge

S&F 6mm thick tinted glass as approved by GE, fixed to existing aluminium door/ windows including hacking out existing glass and provn of rubber beading all as directed by Engr-in charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden /steel frames or stone , concrete or brick surrounds, glazed with putty or fixed with beads all as directed by Engr-in charge.

S&F 4.00 mm thick sheet figured glass pin headed type and glazing with oil putty in square n exc 0.50 Sqm in each pane.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) including fixing bolts and Plastic water closet seat ( black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device) complete all as specified and directed.

S&F in repairs jet spray to EWC with PVC nozzle, PVC fish plates and PVC fish plates and PVCflexible pipe etc complete.

S & F for Vitreous China urinals, bowl type flat back, size 465X355X265mm white (minimum), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; (Excluding flushing cistern and waste pipe )

Demolition of cement concrete any description , any position otherwise provided complete all as specified and directed.

M&L for 50mm thick cement concrete type B-1 1:2:4 ( 20mm graded aggregate ) finishing the surface even and smooth without using extra cement all as directed by Engr-in charge

M&L for 100mm thick cement concrete type B2 1:2:4 using 40mm graded aggregate finished even and smooth without using extra cement all as directed by Engr-in charge.

Forming dummy joints 30 mm deep X 10 mm wide filled with sealing compound grade 'B' all as directed by Engr-in charge

Demolition of stone slabs any description or any thickness laid dry or laid dry and pointed in any mortar complete all as specified all as directed by Engr-in charge

M&L for 20mm thick Granite (Z Black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm thick screed bed of cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed. NOTE : Cost of Screed Bed shall deemed to be included in QUOTED UNIT RATE.

M&L Granite (Z Black) tiles 12 to 15mm thick machine cut, in vertical surfaces such as riser, skirting, dado, etc. including rounding edges, nosing, pointing on nose, etc., over and including 12mm thick screed bed in cement morter 1:3 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete all as specified and as directed. NOTE : Cost of Screed Bed shall deemed to be included in QUOTED UNIT RATE.

sudarshan builders

SARASWATI CONSTRUCTION

Jyoti Refrigeration

GPR Construction Co.

BHAVANI PROVISION STORES

Hi-Tech Systems

Ahmed B Khatri