A & A to Street Light and Flood Light in Dhrangadhra City State highway at Dhrangadhra, Dist- Surendranagar.

less In Figures In Words according

to estimate

1 1098 Mtr Replacing old and U/s By Supplying and erecting Flexible PVC insulated 46.46 Rupees Forty Six

multi strand multi core 1.1 kv grade ISI marked copper wires of following And Paise Forty Six

size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed

(Old-720, New-378)

2 8 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte 56.56 Rupees Fifty Six

multi stranded, annealed copper conductor with heat resistant PVC And Paise Fifty Six

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears,

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required.

(e) One wire 6.00 sq. mm

3 2 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte 91.91 Rupees Ninety One

multi stranded, annealed copper conductor with heat resistant PVC And Paise Ninety

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears,

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required.

(f) One wire 10.00 sq. mm

4 122 Ea Replacing Old and U/s By Supplying and erecting LED street light / Flood 5976.17 Rupees Five

light fittings with High power White LEDs wattage of 3 Watt and above Thousand Nine

Hundred Seventy

assembled on single MCPCB, efficiency more than 130 lm/w and Six And Paise

corrosion free High pressure die cast aluminum housing with smooth Seventeen Only

finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection.

(iii) Above 60 to 90 watts Cat-lll

(old-80, New- 42)

5 6 Ea Replacing old and U/s BySupplying and erecting LED street light / Flood 9647.52 Rupees Nine

light fittings with High power White LEDs wattage of 3 Watt and above Thousand Six

Hundred Forty

assembled on single MCPCB, efficiency more than 130 lm/w and Seven And Paise

corrosion free High pressure die cast aluminum housing with smooth Fifty Two Only

finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection.

(vi) above 160 to 200 watts Cat-lll

(Old -6, New-0)

6 2 Ea Providing and erecting Approved make Four pole moulded case circuit 6173.12 Rupees Six

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal Thousand One

Hundred Seventy

current rating up to 25 A to 100A. with Fixed thermal & magnetic release Three And Paise

suitable to work on A.C. supply 50 c/s. with all internal connections, Twelve Only

spreader tinned copper & complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

7 1 Ea Providing and erecting Approved make Earth fault Relay suitable to 4687.41 Rupees Four

mount with inter connection suitable to following size of moulded case Thousand Six

Hundred Eighty

circuit breaker having CT ratio & MCCB rating as following along with Seven And Paise

shunt trip 220V AC. with all internal connections & complete erected in Forty One Only

existing M.S.housing..

(1) 15 A -100 A , CT Ratio 1/100

8 0.5 RMT Supplying and erecting triple pole & neutral 440V / 500V panel mounting 1961.42 Rupees One

Copper Busbars with four equal Nos. of electrolyte bus having current Thousand Nine

Hundred Sixty One

density not more than 1.6 Amp. / sq.mm (Rated current / cross section And Paise Forty

area) duly wrapped with colour insulating tape for phase sequence of Two Only

following current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in existing

cubical panel with necessary connections.

(A) Suitable for 100 Amp. Capacity

9 122 Ea Replacing Old and U/s By providing and erecting Miniature circuit 270.68 Rupees Two

breaker single pole 0.5A to 2A system and having breaking capacity 10 Hundred Seventy

And Paise Sixty

KA to be erected in existing box. confirming to IS 8828/1996 with ISI Eight Only

Cat.III (0ld-80, New-42)

10 4 Ea Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B 638.32 Rupees Six Hundred

curve) having 10KA breaking capacity & confirms to IS :8828 in existing Thirty Eight And

Paise Thirty Two

box having following capacity Only

(b)40 Amp. Cat.III

11 80 Kg Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 77.77 Rupees Seventy

SWG. Seven And Paise

Seventy Seven Only

12 18 Ea Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long 'B' 823.15 Rupees Eight

grade G.I. pipe with necessary coupling buch buried in specially prepared Hundred Twenty

Three And Paise

earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For Fifteen Only

13 18 Ea For using salt and charcoal / coke as required for pipe type earthing. 171.70 Rupees One

Hundred Seventy

One And Paise

Seventy Only

14 1 Ea Supplying & erecting earth pit of minimum bore dia.150mm size 4591.46 Rupees Four

approved make Earthing Electrode consisting Pipe-in-Pipe Technology as Thousand Five

Hundred Ninety One

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having And Paise Forty Six

Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe Only

dia of 25 mm having 200-250 Micron galvanising, connection terminal

dia of 12mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover. (A)(approved make

OEM has to submit test certificate including value of earth resistance of

installation duly stamped and signed by agency and officer Incharge has

to ensure the value of earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

15 1290 Mtr Replacing old and U/s By Providing and erecting XLPE (IS:7098)(I)-88 126.25 Rupees One

ISI armoured cable multistrand / Solid Aluminium conductor for 1.1 KV. Hundred Twenty Six

And Paise Twenty

to be laid on wall with necessary clamps or in existing trench / pipe of Five Only

following size of cables

(B) 4 core 6 Sq. mm

(old-210, New-1080)

16 40 Mtr Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 153.52 Rupees One

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with Hundred Fifty Three

And Paise Fifty Two

necessary clamps or in existing trench / pipe of following size of cables Only

(A) 4 core 16 Sq. mm

17 1220 Mtr Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or 357.54 Rupees Three

required depth for laying any size of cable or locating the fault all over Hundred Fifty Seven

And Paise Fifty Four

the run and back filling the same and making the surface as normal Only

(B) If additional machinery like hammer driller or JCB use [Add]

18 10 Mtr Drilling the road without breaking the road surface (Asphalt) for laying of 492.88 Rupees Four

cable for feeding power supply by making up to following size of holes at Hundred Ninety

Two And Paise

both ends complete. Eighty Eight Only

(A) Up to 100 mm bore dia

19 10 Mtr Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below 226.24 Rupees Two

ground across the road crossing or on floor with necessary material in an Hundred Twenty Six

And Paise Twenty

approved manner and making the ground as per original. Four Only

(F) 100 mm dia.

20 1220 Mtr Providing & laying approved make Double walled corrugated pipes 62.62 Rupees Sixty Two

(DWC) of polyethylene(conforming to IS 14930 II )with necessary And Paise Sixty Two

connecting accessories of same material at required depth in existing

trench for laying of cable. below ground / road surface for enclosing

(A)50 mm outer dia

21 2 Ea Providing and, fixing heavy duty flange type brass cable gland with 38.38 Rupees Thirty Eight

rubber ring for PVC insulated armoured cable complete with out going And Paise Thirty

Eight Only

tails, insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm

22 2 Ea Providing and, fixing heavy duty flange type brass cable gland with 47.47 Rupees Forty Seven

rubber ring for PVC insulated armoured cable complete with out going And Paise Forty

Seven Only

tails, insulating tape etc for following size of cables.

(D) 2 to 4 core 16 Sq. mm

23 8 Ea Solder less crimping type Aluminium lugs conforming to IS suitable for 15.15 Rupees Fifteen And

cable of following size evenly crimped with high pressure tool & Paise Fifteen Only

connected to switchgear terminals with brass/cadmium plated nut bolts in

an approved manner.

24 36 Ea Supplying and erecting approved make Octagonal pole made from HR 11411.99 Rupees Eleven

sheet steel. The pole should be made as per IS. and shall be coated with Thousand Four

Hundred Eleven

hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local And Paise Ninety

wind speed with integral Junction box consist of terminal plate of min Nine Only

6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB

Mounting, stud type terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per details given by

manufacturer considering site requirement.

(E) 7 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with

225mmX225mmX16mm base plate, 4-M20 Bolts and 600mm long with

necessary G.I. J Bolts .Approx Pole weight 67 kg

25 40 Ea Replacing old and U/s By Supplying & erecting approved make SMC 476.72 Rupees Four

press moulded composite FRP. loop-in, loop-out approx. 2mm thick box Hundred Seventy

Six And Paise

complete with Bakelite connector strip 5way(3P+N+E),DIN rail for Seventy Two Only

mounting mob & hinged doors as per requirement having locking

arrangements with mounting clamp with nuts, bolts & washers suitable

for erection on pole with cable clamps& earth bolt of following size of

(C)150mm x 125mm x 100mm [deep]

(Old-40, New-0)

26 1 Ea Supplying & erecting approved make SMC press moulded composite 3420.87 Rupees Three

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite Thousand Four

Hundred Twenty

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged And Paise Eighty

doors as per requirement having locking arrangements with mounting Seven Only

clamp with nuts, bolts & washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.

(I) 400mm x 300mm x 190mm [deep]

27 30 Ea Providing and erecting street light pole bracket comprising main B Class 614.08 Rupees Six Hundred

GI pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I Fourteen And Paise

Eight Only

sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. /

require size pole top having sufficient fasteners for fixing the brackets

and having spread of 1 mtr. length with suitable rise as per site condition

& suitable welded stiffener reducer and nipple with check nut complete

painted with one coat of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[A] Single Arm bracket 1 Mtr

28 6 Ea Providing and erecting street light pole bracket comprising main B Class 829.21 Rupees Eight

GI pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I Hundred Twenty

Nine And Paise

sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / Twenty One Only

require size pole top having sufficient fasteners for fixing the brackets

and having spread of 1 mtr. length with suitable rise as per site condition

& suitable welded stiffener reducer and nipple with check nut complete

painted with one coat of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[B] Double Arm Bracket 1 Mtr

29 1 Ea Supplying & erecting IP 55 grade following size section pillar fabricated 16691.26 Rupees Sixteen

from joint less M.S. Sheet with angle iron legs made from jointless M.S. Thousand Six

Hundred Ninety One

Angle with cable clamps to be buried in ground to have appropriate And Paise Twenty

erection to work uniform until erected with cement concrete foundation Six Only

and 45 cm high bricks work finishing with plaster etc. hinged double door

internally supported on both side,

with internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite sheet. Painting the Section

Pillar inside and out side with three tank powder coated paint. section

pillar roof should be without joint with water leakage proof & tested as

per IP 55 test & followed by IS 2147 of

(A) 150 X 90 X 75 cm section pillar fabricated from 14 Gauge MS Sheet

with angle iron legs 95 cm long made from 40 X 40 X 6 mm thick MS

30 1.4 sq.mtr Supplying and erecting HYLAM sheet on existing angle iron frame.for 1927.08 Rupees One

following thickness Thousand Nine

Hundred Twenty

(E) 10mm Seven And Paise

Eight Only

31 2 Ea Supplying & erecting approved make Digital time switch having lithium 3168.37 Rupees Three

cell 6 years operative and operate battery backup 1 channel day clock Thousand One

Hundred Sixty Eight

with 14 memory programme, suitable to operate on 240V + 5%, 16A with, And Paise Thirty

floating contacts Minimum switching setup time 1 minimum & LCD Seven Only

display. Also comprised permanent ON/OFF switching. Programming

switches & housed in fire proof thermoplastic enclosure & transparent

cover erected as required with necessary connection erected as directed.

32 2 Ea Supplying & erecting power contactor ,AC3 duty for time switch 2782.55 Rupees Two

complete erected as per direction Cat III Thousand Seven

Hundred Eighty

(D) 4 pole 440V 40 Amp. Two And Paise Fifty

Total Rs.

In Words : Rupees Twenty Lakh(s) Ninety Eight Thousand Thirty And Paise Seventy Eight Only

I/We am/are willing to carry out the work at ____________% above/below (in Figures)__________________________ percent Above /

below (in words) the estimated rates mentioned above amount of my\our tender works out as under :-

Estimated amount put to Tender Rs._________________

Deduct _____% below Rs._________________

(-)Less For Dismantle Material Rs._________________

Net Amount Rs._________________

(Rupees in Words)____________________________________________________________.

Estimated amount put to Tender Rs. _________________

Add. ________% Above Rs. _________________

(-)Less For Dismantle Material Rs. _______________

Net Amount Rs. _________________

(Rupees in Words)____________________________________________________________.

A I/We hereby declare that I/we have visited the site and fully acquainted my self / our selves with the local situation regarding material,labour

and other factors pertaining to the work before submitting this tender.

B I/We hereby declare that I/we carefully studied the conditions of contract, detailed technical specifications and other tender documents of

this work and agree to execute the same accordingly.

C ERDA Testing will be taken for any illuminary and wires/ Cable items mentioned above in tender on random basis and charges of the

same will be deducted from the bill. Contractors are advised to quote the rate by considering the same.

D Any Excess in tender Item/ Extra item if needs to be Execute, Contractors has to carry out on the instruction of Competant Authority on

Tender Submitted rate, No Excuse will be Accepted. Hence Contractor are Requested to Quote the rate Considering this Condition.

E Contractor are requested to quote the Tender by considering that payment will be made after availability of grant. Contractor has to start the

work immediately after issue of work order and as per instruction of Engineer in-charge irrespective of availability of grant.

F This Estimate has been prepared on the new SOR which is exclusive of GST hence GST Additional Will be paid to the agency as per

existing guidelines.

(Signature of the Contractor)

Deputy Executive Engineer Executive Engineer,

Morbi Electrical R&B Sub Division Electrical (R.&B.) Division

Morbi Bhuj-Kutch

Note 1 Please strike out whichever is not applicable.

2 In the case of tendered amount being quoted incorrectly the quoted pered percentage Below/Above will be considered as final.