PERIODICAL SERVICES AND REPAIR/REPLACEMENT OF JOINERY, SANITARY FITTING AND ALLIED WORK SERVICES AT AF STN MOTHALA UNDER GE(AF) NALIYA

Amount

Taking down of cement plaster from surfaces of wall of any description including raking out joints, hacking out for key, scrubbing down with water etc including removing debris out side MD land complete all as specified and directed.

Material and labour for rendering 5 mm thick cement plaster on concrete surfaces of ceiling in CM 1:4 , finish the surface even and smooth wihout using extra cement etc complete all as specified and directed.

Material and labour for rendering 10 mm thick cement plaster on concrete surfaces of walls in CM 1:6, finished the surface even and smooth wihout using extra cement etc complete all as specified and directed.

Material and labour for rendering 15 mm thick in two coat (10+5mm) cement plaster on concrete surfaces in CM 1:6 in base coat and 2nd coat 5mm thick in CM 1:4 using water profing compund (3% by weight) complete all as directed. Note :- WPC shall be measured and paid separatly under relevant item of this Schedule.

Supply only integral water proofing complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls, and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of primer in camoflage pattern etc complete all as per specified and directed.

Material and labour for complete removal of existing treatment on walls of any description and preparing surfaces of walls and applying two coats of 100% acrylic anti fungal paint (In approved camouflaged pattern) over one coat of primer complete all as specified and directed.

Material and labour for preparation of old plastered/unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

Material and labour for preparation of old surface of ceiling of any description and applying one coat of white wash complete all as specified and directed.

Material and labour for preparation of old surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed.

Material and labour for preparation of old surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed.

Material and labour for preparation of old decorated/painted surfaces of walls and applying one coat of plastic emulsion paint complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying two coats of oil bound distemper over a coat of with alkali resistant priming paint over 3 mm thick layer of wall care putty complete all as specified and directed.

Material and labour for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old wooden surfaces of any description, width or girth including cleaning and preparing the surface and applying one coat of french polishing complete all as specified and directed.

Cutting out the shrubs, plants and trees of any description any girth and taking out the roots from the walls or roofs and making good of dismentled portion in CM 1:3 complete all as specified and directed.

Material and labour for cutting and widening existing cracks not exceeding 1 cm in girth to 'V' section in existing walls. cleaning out, wetting including pressure grouting(using suitable pneumatic pressure grouting equipment) with cement and sand slurry 1:3 complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutter from the frame) not exceeding 1.5 Sqm each complete all as specified and directed.

All as per item serial item number 21 here-in-before but exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down shutter of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutter of any description exceeding 2 Sqm each complete all as specified and directed.

Taking down shutter of any description exceeding 1 Sqm but not exceeding 2 Sqm each and refixing the shutter in same opening after replacing frame complete all as specified and as directed. Note: - Frame/chowkats shall be measured & paid under item number 27.00 & 28.00 mentioned here-in-after.

Taking down shutter of any description exceeding 2 Sqm but not exceeding 4 Sqm each and refixing the shutter in same opening after replacing frame complete all as specified and as directed. Note: - Frame/chowkats shall be measured & paid under item number 27.00 & 28.00 mentioned here-in-after.

Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other Frames/Chowkhat of size 50 x 125 mm comprising of Virgin PVC polymer of K Value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire resistant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note :- (i) M.S. hold fast/lugs or SS dash fasteners shall be measured and paid seperately. (ii) For WPC solid door/frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply and fix factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of Virgin PVC polymer of K Value 58-60 (Suspension Grade), calcuim carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire resistant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note :- (i) M.S. hold fast/lugs or SS dash fasteners shall be paid seperately. (ii) For WPC solid door/frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply and fix 35 mm thick factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note:- Stainless steel butt hinges and necessary fittings shall be paid separately.

Supply and fix 35 mm thick factory made single extruded WPC (Wood Polymer Composite) solid decorative type of glazed and skeleton shutter, open rebated and prepared to receive glass, gauze etc (with out sash bars)including middle stiles overal l(top to bottom) , edges of framing plain, chamfered or rounded,fitted with out and retired beads for securing glass etc size of membrane of shutter as specified in SSR part I, Section 8, clause 8.20 (a) shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note:- Stainless steel butt hinges and necessary fittings shall be paid separately.

Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain col-our PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm x 47 mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed sheet reinforced with M.S. square tube complete all as specified and directed.

Supply and fix for mild steel works for hold fasts conforming to Fe-290 Gde E-165 complete all as specified and directed.

Material and labour for providing cement concrete 1:2:4, type B-1 (using 20 mm graded aggregate) for hold fasts etc complete all as specified and directed.

Supply and fix for 150 mm long aluminium, anodized barrel tower bolts of extruded section and fixed (ISI Marked) complete all as specified and directed.

All as per serial item number 35.00 here-in-before but 125 mm long (ISI Marked).

Supply and fix 300 mm long aluminium alloy, anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed (ISI Marked) complete all as specified and directed.

Supply and fix 100 mm size butt hinges stainless steel (ISI Marked) complete all as specified and directed.

All as per serial item number 38.00 here-in-before but 75 mm size(ISI Marked) complete all as specified and directed.

Supply and fix continuous (piano) hinges, mild steel, 30 mm width flaps (when open), bright finish or electro galvanized (ISI Marked) complete all as specified and directed.

Supply and fix 300 mm, mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

Supply and fix 150 mm extruded aluminium alloy handles, fabricated type anodized (ISI Marked) complete all as specified and directed.

Supply and fix 100 mm extruded aluminium alloy handles,fabricated type anodized in repair (ISI Marked) complete all as specified and directed.

Supply and fix floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring, fixed in floor (overall length of cover plate 150mm) complete all as specified and directed.

Supply and fix stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples/wooden beads complete all as specified and directed.

All as per serial item number 45.00 here-in-before but fixed in repair.

Dismantling boarding of any description and fixed in any position with nails complete all as specified and directed.

Supply and fix 25 mm thick flush shutters, solid core commercial construction with block board core and plywood face panels, commercial type one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

Supply and fix 18/19 mm thick pre-laminated particle board, inerior grade, prelaminaed one side wih decorative choice laminaion & other side balancing white lamination lamination fixed with screws to timber frame work complete all as specified and directed.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel over a coat of pink primer complete all as specified and directed.

Supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

Supply and fix anodised aluminium powder coated (minimum 50 micron thickness) door shutter with frame, partly glazed with 5.5mm thick tinted glass and partly panelled with 9mm thick both side decorative prelaminated particle board exterior grade including rubber bead, joining cleat for fixing, aluminium door handle 150 mm size and tower bolt 200mm size, double action floor spring hydraulically regulated made up of minimum 1.2 5mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing brass pivot, mortice lock vertical type of mild steel 4 levers of size 100mm etc as mentioned here in below complete all as specified and directed:- (a) Frame (top and side) section - 101.60 x 44.75 x 2.4mm (Section No. 14021) (b) Vertical members of shutter Section-85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section - 83.50 x 44.45 x 2.00mm (Section No 19581) (d) Lock rail (middle member) of shutter Section - 150.00 x 44.45 x 3.00 mm (Section No. 19596) (e) Bottom Members of shutter Section - 150.00 x 44.45 x 3.10mm (Section No. 19584) (f) Glazing clip for securing glass - 0.80 mm thick (Section No. 19370). Make:- Aluminium Section number mentioed above are of make Jindal, Contractor may use similar section of other make mentioned in Appx 'B' to Particular Specification.

Supply and fix powder coated aluminium three track sliding window comprising of one fly proof shutter and two glazed shutters with window frames of size 92mm x 31.63mm x 1.50mm thick and shutter frames of size 40mm x 18mm x 1.55mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement and with aluminium Deco grill DG/01 7x4.5mm thick, fixed with channel of size 38mm x 12mm x 13mm (Section 8778) complete all as specified and as directed. Notes:- (i) Glass filling in panels of windows and aluminium wire mesh/wire cloth shall be deemed to be included in the quoted rate for the item. (ii) Aluminium alloy wire cloth in panels of wire gauzed shutter shall be 0.45 mm nominal dia of wire and average width of aperture 1.40mm, fixed with aluminium wire staples shall be deemed to be included in the quoted rate for the item. (iii) Glass filling in panels of glazed shutter shall be 5mm thick tinted sheet glass of approved make and shade/ tint shall be deemed to be included in the quoted rate for the item. Make:- (i) Aluminium Section number mentioed above are of make Jindal, Contractor may use similar section of other make mentioned in Appx 'B' to Particular Specification. (ii) Make of Grill : DECO GRILL or equivalent make as approved by GE.

Supply and fix aluminium (powder coated in approved colour) glazed/ gauzed window shutters with frame, side hung type with sash bars, including necessary joining cleats for fixing etc, glazing clips, rubber packing, aluminium anodised snap beading, screws, aluminium (anodised) fittings such as peg stays 150mm long - 01 No, hooks and eyes - 01 Set, hinge type B-21, 100mm long - 01 No, suitable handle - 01 No, locking device, tower bolts 100 mm long - 02 Nos. and glazing panels with 5.5mm thick coloured/ tinted glass with rubber beading, glazing clips and gauzing in with stainless steel wire mesh 0.36mm nominal dia of wire with average 1.40mm width of aperture fixed with aluminium 'C' section, with aluminium (anodised) grill made out of 7mm wide flat, square, rectangular or similar section, fixed with channel of size 38mm x 12mm x 13mm (Section 8778) complete all as per manufacturer's catalogue 7 specifications, complete all as specified and directed. Make:- (i) Aluminium Section number mentioed above are of make Jindal, Contractor may use similar section of other make mentioned in Appx 'B' to Particular Specification.

Supply and fix aluminum window/ventilator fixed type with two track of sec 85.00 mm x 31.75mm 1.50 mm thick section No 78687,24758 shutter of sec 18 x 40 x1.25 mm (Sec No 8663/8664/8665) with rubber gasket beading and locking arrangement including taking down etc complete all as specified and directed Note :- Glass shall be measured and paid separetely. Make:- (i) Aluminium Section number mentioed above are of make Jindal, Contractor may use similar section of other make mentioned in Appx 'B' to Particular Specification.

Supply and fix in repairs for aluminum anodised grill of 7 mm dia rod square, rectangular, circular or similar tupe of shape aperture not exc 7.00 cm in length or width fixed with H or F channel 38 mm x 12 mm x 1.30 mm (Sec No 8778) Make of Grill : DECO GRILL or equivalent make as approved by GE.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame or metal frame, glazed with putty or fixed with beads complete all as specified and directed.

Supply and fix 4 mm thick sheet glass ordinary quality and glazing with oilputty or wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix 4 mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix in repairs magnet type PVC door stopper 30 to 40mm dia fixed with screw behind the door complete all as specified and directed.

Supply and fix in repairs, aluminium (Die cast) body, door closer hydraulically regulated designation No-1, universal type, suitable for door shutters of weight not more than 35 kg complete all as specified and directed.

Supply and fix in repairs, double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

Material and labour for repair of aluminium door of size exceeding 1.2 sqm including taking down of aluminium door and refixing in same opening, including fixing of 6mm dia bolts with threads overall in top,lock and bottom rail section, floor door spring , dead lock and all necessary fitting\fixture complete all as specified and directed

Taking down for repairs, painting, greasing and maintainence and re-fixing rolling steel shutter of area exc 4 Sqm including welding, riveting, changing of hinges etc if required, making good the disturbed surfaces complete all as specified and directed.

Taking down for repairs, painting, wood rot, framing molding interior and exterior trim door replacement, porches, rails, maintainence and re-fixing panel door and glazed door or flush door of area exc 1.5 sqm but n exc 4 Sqm including welding, riveting, changing of hinges etc if required, making good the disturbed surfaces complete all as specified and directed.

Supply and fix in repairs, 25 mm dia aluminium anodised curtain rod cut to length and fixed including brackets, stops, roller etc complete all as specified and directed.

Supply and fixing in repairs, brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Sipply and fix semi perofrated 12 mm thick micro tegular edged false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS tiles 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000 mm,cross-T of size 15 x 32 mm of length 1200 mm and secondary intermediate cross-T of size 15 x 32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85 x 25 x 2 mm. Galvanised iron perimeter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction.

Hari Construction (BID ID -3453448)

NILESH SUBHASH KARALE (BID ID -3454915)

M/s. Shree Shakti Enterprise (BID ID -3453959)