SPECIAL REPAIR RENOVATION OF TOILET OF SCHOOL BUILDING AT KV NO 1 AT AF STN BHUJ

Amount

Demolition reinforcement Concrete Roofs floors(other than Ground floors), beams, landings, chhajjas and similar suspended work Complete all as per specified and directed by Engr-in-charge

Demolition block work or stone/boulder masonry, build in lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles Complete all as per specified and directed by Engr-in-charge

Taking down chowkats or frame n exc 1.5 sqm with shutters (without taking off shutters from the frames)

Ditto but exc 1.5 sqm but n exc 4.00 sqm each with shutters (without taking off shutters from the frames)

Dismantling of water tanks exc 500 & n exc 1000 complete all as specified and directed by Engineer-in-Charge

Taking down or up steel tubing 15mm bore and removal from site as directed by EIC.

Ditto as per item no 6 above but 20mm bore

Demolition cement Concrete is ground floors and pavings n exc 15 cm thickness (below or above ground level)

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting outin hard/dense soil.

Surface excavation in hard/dense soil n.exc. 30 cm deep and averaging 15 deep and getting out in

M&L for Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in foundations, filling and mass-concrete

M&L RCC Design mix M-30 (using 20mm graded aggregates ) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M&L RCC Design mix M-30 (using 20mm graded aggregates ) for columns, pillars, piers, posts and struts

M&L RCC Design mix M-30 (using 20mm graded aggregates ) for Beams, cantilevers, bressummers, lintels over 1.5m span

M&L RCC Design mix M-30 (using 20mm graded aggregates ) for slabs supported on walls, beams and columns in floors, roofs, landings, balcony, canopies, deck slabs and in shelves and the like

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M&L for Formwork to sides of pillars, posts, struts, piers, columns, and stanchions

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for Precast cement concrete block masonary with solid blocks exc 10cm in width Type C1 (1:5:8) 20mm graded and setting in cement mortar 1:6 all as specified and directed

M&L for glazed ceramic coloured tiles Ist quality in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and icluding 10mm plaster in CM 1:4 all as specified and directed.

M&L for rendering on concrete surfaces 15mm thick in two layers first coat 10mm thick in CM 1:6 and second coat 5mm thick in CM 1:4 with water proofing compound @3% by wt of cement, finished even and fair.

M&L for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:4 and finished even and smooth without using extra cement as specified.

M&L for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces.

M&L for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of Acrylic putty by finishing the surfaces even and smooth complete all as specified and directed by EIC.

M&L for preparation of new or previously untreated concrete extrernal surfaces and applying two coats of exterior emulsion paint all as specified and directed by EIC .

M&L for preparing new plastered ceiling/soffits of chajjas surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick cement concrete type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base

Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for non skid ceramic coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exc. 0.11 Sqm but n.exc. 0.18 Sqm in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed 15mm thick in cement mortar 1:6 complete as directed by EIC.

M&L in repairs for 20mm thick granite, Z black (table rubbed and polished) for platforms, wall lining (veneering to wall), cills and in similar items laid over and including 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixutre of pigment to match with shade of granite external edges rounded.

M&L for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out of JINDAL/ INDAL anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) all as specified and directed.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately. Note : main section of aluminium shall be used 100mmx45MM with same thickness as mentioned in lieu of drg 65mm x 38mm above reffered due to less space available for fixing wire gauge shutter fixing grill

M&L for aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 4.4 mm x 7mm

M&L, water proofing treatment on roof and preparing the surfaces to receive WPT treatment , applying cold bituminous primer @ 0.30 ltr / Sqm conforming to IS 3384 applied on plastered surfaces including side walls , followed by a layers of APP based polymeric membrane reinforced with polyster non woven fabric (weighing 3.5 Kg/Sqm(minimum) and 3 mm thick) with mineral finish laid on primed surface by torch application with side overlap 100 mm and ends over laps 150 mm , joints sealed properly as per manufacturers instructions all as specified and directed .

M&L for padding in PCC 1:3:6 type C1 (using 20mm graded aggregate) laid to minimum consolidated thickness 50mm finished slope of 1:40.

M&L, 10mm thick rendering in cement mortar 1: 3 on concrete surfaces with WPC, finished even and smooth W/O using extra cement as in roof. (WPC shall be measured & paid seperately) complete all as specified and directed .

Supply only integral water proofing compound. (ISI marked)

M&L for 75mm thick cement concrete type C2 1:3:6 using 40mm graded aggregate as plinth protection finished even and smooth without using extra cement, laid in bays, joints filled with sand and bitumen mixture at 1:1 ratio complete all as directed

S&F in repairs vitreous china wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets.

S&F in repair for fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repairs Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repair vitreous china sqatting pan of pattern Orisa patern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to fushing pipe, anti-syphonage pipe, etc complete

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

S&F in repairs PVC low level valveless, syphonic action type flushing cistern, low level, white, with inlet, bll valve, flaot and handle including brackets of 10 Ltr capacity.including flush pipe

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F 15mm bore Stop valve, cst copper alloy screwed down high pressure, fancy type, screwed both ends (externally threaded) for iron pipe or for union and fixed of sizes:-

S&F Bib tap cast copper alloy 15mmbore high pressure fancy type, screwed both ends for iron pipe for brass ferrule and fixed.

S&F in repairs Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding mortar 1:2 securing urinal to plugs and including 60mm long screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets flush pipes grating and union for discharge pipe.

S&F Vitreous china urinal partition white of size 310x700 mm.

S&F in repair Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms)

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F in repairs of UPVC floors trap, plain with grating , diameter of outlet in 75 mm including jointing to waste pipe to fixed with solvent cement ( Make Astral type 'B' or equivalent)

S/F CPVC pipes ISI marked IS 157778 with all fitting for hot and cold water fixesd with solvent cement complete to walls and ceiling or laid in floors of following sizes (SDR 13.5 of make astral or equivalent of supreme / finolex).

20mm bore of pipe

25mm bore of pipe

32 mm bore of pipe

S & F rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 1000 ltrs including taking down existing tank also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms)( Make of tank Sintex cat no CCWS 0075-02-TLW or equivalent of makes given in Appendix B to PS Make of ball valve Prayag or equivalent in polytuff as approved by GE

S&F, in repair 20 mm bore gun metal globe / gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F, in repair 15 mm bore gun metal globe / gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required all as directed by Engr-in-charge following bore of pipe

100/110mm dia of pipes

75mm dia of pipe

S&F of UPVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors of following size :- (Make : Astral type 'B' pipes or equivalent)

110mm dia of pipe

75mm dia of pipe

S&F of UPVC bends equal of any radious with door, ISI marked, IS-14735, jointed with solvent cement for 75mm size pipes(Make : Astral type B pipes or equivalent of finolex/supreme

S&F of UPVC bends equal of any radious with door, ISI marked, IS-14735, jointed with solvent cement for 110mm size pipes(Make : Astral type B pipes or equivalent of finolex/supreme

S&F of UPVC junction single 'Tee' equal with door opening, ISI marked, IS-14735, jointed with solvent cement of for 110mm sizes :- (Make : Astral type 'B' pipes or equivalent)

S&F of UPVC cowl for 110mm size pipes ISI marked, IS-14735, jointed with solvent cement of for 110mm sizes :- (Make : Astral type 'B' pipes or equivalent)

S&F of UPVC P trap for 110x110mm size pipes ISI marked, IS-14735, jointed with solvent cement of for 110mm sizes :- (Make : Astral type 'B' pipes or equivalent)

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape reqd including cranking bending spirally for hoping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than .9mm dia or securing with clips quality conforming to

ditto all as per item above her in before but 5 mm and above upto and incl 10 mm dia in stirrups, spacers and binders

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured)

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

S&F PVC door comprising of shutter and frame of Make : Rajashri, Accura Polytech Pvt Ltd (Accucel) all as shown on drg No.CEAA/TD/149 sheet No. 1/1 (PVC RIGIDE FOAM) , door frame/ chokats of solid rigid foam profile FP-6030 and shutter of solid PVC foam profile FP 7114 with 4 mm thick high pressure compact laminate as infill (Panel) including necessary hardware fittings all as specified and directed by EIC.

Demolition of bricks( laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc (each layers) laid bedded and pointed in any mortar

S&F vitreous china squatting plate urinal.

Providing precast cement concrete louvers and jallis 25mm thick (measured solid) set incement mortar 1:4 including all mouldings but excluding frame complete (Type B-0 1:2:4mm) (12.5mm graded aggregate).

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants,regulators, sockets etc.incl removing materials to store for kepping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc. all as specified and directed.

Taking down main switch/DB’s including MCB’s with board and fixture of any description and making good disturbed surface of walls etc complete.

M&L for point wiring (Surface) with 1100 volts grade PVC insulated FRLSH single core multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) connected to common earth dolly drawn into and including heavy duty non metalic PVC conduit, ISI marked, not less than 20 mm dia of thickness 1.8 mm fixed to wall/ceiling with all connected fittings including pressed steel terminal boxes suitable size, 3mm thick bakelite white colour sheet top cover ISI marked with brass screws and cup washers for mounting switches, sockets etc all as specified and directed for the following

One light point controlled by one, one way switch single pole piano type

One Fan point controlled by one, one way switch single pole piano type

One 3 pin 5 Amps socket out let on same board

S&F in replacement switch piano flush type 230/250 Volt, 5 Amps single pole one way, all as specified and directed.

S&F in replacement socket 2 in 1, 5 pin 5 Amps, flush type, ISI marked all as specified and directed

S&F in replacement ceiling rose surface bakelite 65mm x 50mm three terminal all as specified and directed

S&F Sheet metal enclosure MCB SPN distribution board, double door, IP 43 class, including suitable size copper bus-bar, 240V, 8 Way with shrouded neutral bar, earth bar and incld. cable ties and suitable size blanks, complete all as specified and directed. NOTE - (a). Cost of suitable size cable lugs and materials required for flush fixing of DB is deemed to be included in the quoted rate. (b). Cost of cutting chases in wall for flush fitting of DB and making good to wall with CM 1:4 and painting the same in order to match the same with the existing wall all to the satisfaction of Engr-In- Charge is deemed to be included in the quote rate. Make : Legrand/Polycab/Standard/Havells.

S&F isolators of the under mentioned type and rating and fixing in DBs (DBs measured and paid for separately) (Note :- Make of the isolator should be the same as that of DB) for the following:

SP of 240 volts 5-40 Amps Capacity, 'C' series

SPN of 240 volts 40 Amps Capacity, 'C' series

Supply and Fix metal body exhaust fan, heavy duty AC single phase 230/240V of size 380 mm sweep 1400 RPM complete incl taking down the old UNSV exhaust fan all as specified & directed by Engineer-in-Charge. Make:Havells or Equivalent in Bajaj//CG/Usha. ( Note: Old unserviceable Exhaust Fan will be deposited to the user).

M&L for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 6 Sqmm single core, copper conductor drawn through and including PVC conduit ISI marked with accessories and 6 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed.(Note: Two runs of conductor with one run of earth wire and PVC conduit will be measured & paid as one unit)

S & F LED in replacement tube light fitting, 1 x 20 W, LED Integrated Batten T5 indoor decorative aluminium extruded T5 LED Battens - integrated type white complete with all accessories with twin core twisted flexible copper conductor cable with suitable size all as specified and directed. Make :- C & S, Model :- Nakshatra/20W/W, Cat Part No :- LTTB4F20WLED/W - 4 ft White or equivalent in Bajaj/Havells/CG.

Supply and fixing in replacement with New generation energy saving and environmental friendly long life LED security light 20W made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with 2.5 mtr twin core copper conductor for connection of security light including taking down old UNSV security light complete all as specifeid and directed by Engineer-in-Charge. Make Havells or eqvlt in Bajaj/Philips

S & F Bracket for street light fitting made out of GI tubing 40 mm med grade pipe1.50 mtr (2' x 1 -1/2'), 135 degree bend with cutting , welding and two MS bracket with nut bolts and washer bracing to pole/on fencing for street light fittings complete all as specified.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel as shown in electrical plate No.3 of SSR Part-I (2009) complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

S & F GI tubing 25 mm bore, medium grade, ISI marked, with and including all fittings such as bends, elbows, tees, short pices etc compelete to wall and ceiling or laid in floors all as specified and directed.

Supply & Fix in replacement PPR Gate valve (brass inserted) of size 25 mm dia Pipe

Cutting & screwing extg steel tubing of size 25 mm dia for alterations or additions or lengthening screw on pipe to form connector and done in position without taking down all as specified and directed.

M/s Pal Builders