SPL REPAIRS TO BLDG NO P-105 (SINGLE LIVING JCO ACCN), BLDG NO P-35 (TOILET BLOCK) 23 JAT AND BLDG NO P-119 (TOILET BLOCK) OF 46 AD REGT AT MIL STN BHUJ UNDER GE(A) BHUJ

Amount

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut Kota stone slab 20 mm to 25 mm thick, as in slab/plateform and thread for steps set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give granite finish, complete all as specified and directed.

M&L Granite slab 20mm thick machine cut, bedded and joined with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps includigng rounding off the exposed edges all as specified and directed..

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L non skid ceramic Coloured tiles, 300mmx300mmx6mm to7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L digital desiner glazed ceramic coloured tiles (300x450 mm) x6mm to 7mm thick on vertical surfaces such as skirting, dados, & riser to steps, set & jointed in neat cement slurry & pointed in coloured cement to match the tile colour laid over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls/celing etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

Supply only water proofing compound (ISI Mark)

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly/old plastered sufaces of walls & applying 2 coat of acrylic exterior anti fungal emulsion paint over a coat of primer complete all as specified and directed.

M&L for preparation of the newly/old plastered surfaces of walls & applying three coats of white wash on wall surfaces complete all as specified and directed.

M&L for preparation of the newly/old plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M&L applying two coat of Whitewash , complete all as specified and directed. by Engr-in-Charge

Taking down existing chowkats or frames of any description and in any position not exceeding 1.50 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

Taking down existing chowkats or frames of any description and in any position exceeding 1.50 sqm but not exceeding 4 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

M & L for powder coated ( minimum thickess of powder coating 50 micron) alumiium frame for slidig widows with two or more channel icludig joiing cleat for fixing etc .complete all as specified and directed

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium sliding window with aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware i.e.. handles, barrel tower bolts, hinges etc, powder coated aluminium snap beading, screws etc. complete, two shutters tinted glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.45mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. Note : (i) Making all edges i.e. cill and jamb good by cement mortar 1:3 (ii) Frame channel will be paid sepreatly.

M & L powder coatedaluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size9mm x9mm x1mm all as specified

S&F powder coated aluminium anodised ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rai ; Panelling of plain colour PVC sheet 5 mm thickness to be fitted in MS frame welded/sealed to the style and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

M & L for 30 mm thick glazed and skeleton shutters of 2nd class Hard Wood(Not less than Hollock wood) local made shutter, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters , solid core construction , with block board core and plywood face panels commenrcialface on both sides with lipping/frame to match with complete all as specified and directed.

Preparation of new painted surface of wood and wood based material any description and in any position over 10 cm width or girth and M&L for applying two coat of synthetic enamel paint over one coat of pink primer all as specified and directed by Engr-in-Charge.

S&F butt hinges 100mm long medium weight, cold rolled mild steel.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section and fixed.

S & F butt Hinges, medium weight, stainless steel,100 mm size complete all as specified.

S&F extruded aluminum alloy handles 150 mm size fabricated type anodized all as specified.

S & F 300 mm aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sjeet, cast or extruded sections or cast aluminium alloy.

S&F in repair brass chromium plated shower rose 125mm size with swivel joints including fixing to steel pipe or union.

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white with integral foot rests and connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern and flush pipe) complete with provision of lime concrete bedding including taking down existing unserviceable WC of any discription and in any position & fixing new WC in repair and making good the disturbed surfaces to match with existing surfaces complete all as specified and directed.

S&F Vitreous China, wash down water closet pan "Pedestal pattern" white including connection to drain and to flush pipe and anti syphonic pipe including all joints and making good the disturbed surfaces complete all as specified.

S&F in Repairs PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle, flush pipe of polyethylene pvc 32mm dia high or low density including brackets complete all as specified and directed.

S&F sinks made out of stainless steel 1 mm thick kitchen or laboratory with ;plugs, washers, and waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, and connecting union to pipe overall size 495 mm x 420 mm with bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed fixed in repair.

Taking up or down existing unserviceable mild steel water tubing and connections 15/20mm dia, any grade, of any description or in any position including fittings complete all as specified and directed

Taking up or down existing unserviceable mild steel water tubing and connections 25mm dia, any grade, of any description or in any position including fittings complete all as specified and directed

Taking up or down existing unserviceable mild steel water tubing and connections 40mm dia, any grade, of any description or in any position including fittings complete all as specified and directed

S&F (concealed / open) 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 15mm bore..

S&F (concealed / open) 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 20mm bore.

S&F (concealed / open) 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 25mm bore.

S&F (concealed / open) 40mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 40mm bore..

Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) ,of any description and in any position, including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories)complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal with access door, 110 mm bore, complete all as specified and directed.

S&F PVC (SWR) branch piece, double (double Y) equal or unequal with access door, 110 mm bore, complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed.

M&L mild steel in framed work [Fe-410-W (grade 250) quality A] as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing+B191and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed.

S&F vitreous china urinals, bowl type flat back, as ordered , minimum size of 465 x 355 x 265 mm, white, with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S & F grating square 150mm size of PTMT (minimum weight 100) complete all as specified and directed.

S&F PVC (SWR) floor trap 75 mm bore, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F Bib taps , cast copper alloy screwed down high pressure with crutch or butter fly handle fancy type long body CP for 15mm dia bore GI Pipe or for brass ferrule and fixed complete all as specified .

S&F Stop valves, cast copper alloy, ISI marked ,screwed down high pressure with crutch of butter fly handle, fancy type , chromium plated,with long shank and cup, screwed both ends for iron pipes or for union , for 15 mm bore , , fixed in repair , complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified

M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Note: Flat Plan area shall be measured Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufactutrer instruction Stage 5:-Filling the Same Portion with plain concrete 1:4:8 Type D-2 Stage 6:- Making holes in wall and fixing 600mm long 40mm dia GI spout for draining the surplus water if any.

M & L for water proofing treatment to roof slab by applying one coat of bituminous / polymrised primer confirming to IS 3384 @ 0.30 ltr /sqm and laying grit finish Actetic Polypropylene (APP) modified membrane pre-fabricated , reinforced with non woven polyester , of 3.50 kg/sqm (minimum) , 3mm thick minimum with minimum 75mm side overlaps and minimum 100mm end overlaps etc all as specified.

M&L PCC 1:3:6 type C2 using 40mm graded stone aggregate as 75mm thick finished fair all as speificed

S&F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 1000 litres capacity, white in colour hoisted and fixed in position with and including all fittings and fixtures in repairs complete all as specified and directed.

Demolition of Concrete (Reinforced) in chajjas ,staircase,landing and other suspended portion at any height, complete all as specified and directed.

S&F Roof trusses (framed) trusses purlins and fastening (etc.,angle, channel,tubular section,round pipe) or flat section including distance pieces, MS plates/ gusset plates, cleats, hold fast etc. conforming to Gde of steel Fe 410-0 or Fe 310-0 complete all as specified and directed.

Dismantling plain or corrugated A/C or steel sheeting, any guage of any description and in any position as in roof coverings and S &F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550MPa as in roof covering / cladding to wall, fixed with L or J hooks all as specified and directed.

Supplying and fixing Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm (weight not less than 600 gms/per sqm) and fixed with aluminium wire staples, wooden beads etc complete all as specified and directed

Hacking out old broken glass of any thickness and any description from metal frame including punching or drilling out old glazing pins/spring clips and providing and S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each panecomplete all as specified and directed.

S&F stainless steel health faucet witrh 1 Mtr tube and hoock complete all as specified and directed ny Engr-in-charge. Confirming to Cat part No ALD573 of jaguar/PRAYAG completed all as specified

S&F in Repair Chromium plated Brass 60 cm longTubular towel rail complete all as specified.

S&F in repair soap dish & holder , colour chrome, brass holder fittings fancy type complete all as specified and directed

Removal of loose and damaged plaster or cover concrete upto good parent concrete or upto reinforcement level, traces of shoots, grease, oil etc. using impact high frequency hammer/chisel without damaging the existing concrete (if required) and by wire brush (metallic brushes only) including cleaning of existing concrete surface carefully by suitable means. The item including all necessary machinery, scaffolding, Providing erecting the safety net of opening 75mm x 75mm x 12 mm size in addition to sturdy GI corrugated arrester tray to prevent the debris falling on ground during progress of work and keeping the same during the entire period of work, providing a well support tubular steel prop arrangement to support the shell and the terrace slab complete from top to bottom, compressor, coarse sand, cleaning the surface by air jet, disposal of unserviceable materials at a identified location as per specification and instruction of Engineer in charge. (Surface area of the member shall be measured for payment purpose)

Cleaning of reinforcement using wire brush to remove corrosion products, dust, dirt etc. and applying two coats of zinc rich epoxy MasterEmaco P 130 (BASF make) or equivalent treatment complying to BS 4652, type 2 for protection of reinforcement from active corrosion, complete w.r.t material, equipment and labour. The material to be used shall have the following key performance properties: Total zinc content in dry film>84% Mixed density : 2.4=0.1 kg/L Volume soilds : 57=3 Payment shall be as per actual application on surface area of reinforcement at site.

M&L for precast cement concrete block masonry with solid blocks of PCC (1:5:8) (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed.

Demolition of pre-cast concrete block masonry built in cement mortar of any description in any position complete all as directed by Engr-in-Charge.

S & F in repair vitreous china wash basin,white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, scrwed down high pressure with or without lettereed hot or cold with long shanks, screwed for iron pipe complete all as specified and directed .

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

Preparation of new iron and steel surfaces of any description over 10cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

BLANK

Taking down carefully existing unserviceable aluminum/copper point wiring (light, fan, socket or power) of any description & in any position complete including all fittings & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc including taking out and removing serviceable fittings/fixtures and making good the disturbed surface of walls, floors, ceiling etc. to match with the existing surfaces complete all as specified and directed

M&L for point wiring with using 1.5 Sqmm (nominal area) multi standard copper conductor, single core, FRLS PVC insulated & unsheathed cable, 1100 volts grade with and including PVC conduit pipe of adequate size concealed type with sunken type pressed steel terminal box and junction boxes 1.6mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings and wiring to be terminated in pressed steel sunken boxes with and including all accessories and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, FRLS PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed for following:- NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes to required depth & making good the disturbed surface in CM 1:4 including finishing the surface to match with the existing surface. (ii) Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iii) The quoted rates shall be deemed to be inclusive for provision of covering sunken boards/terminal boxes / junction boxes of any shape and size with modular type white plate with suitable brass screws and cup washers

One light/buzzer point controlled by one; one way switch.

One fan/exhaust fan point controlled by one, one way switch

One 3 pin socket out let 5 amp (independent) point controlled by one; one way switch.

One 3 pin socket out let 5 amp point on the (same board) with other switches.

All as per item No. 83 here-in-before but with 2.5sq mm size FRLS pvc insulated and unsheathed 1100 volts grade single core stranded (multistrand) copper conductor cable for 3 pin socket outlet 15 amp on independent board.

S&F ceiling rose surface bakelite 63.5 x 20 mm, three terminals, complete all as specified and directed.

Supply and fix modular switch 6 Amp, one way, 1 module, 230 volts AC circuit complete all as specified and directed.

Supply and fix modular switch 16 Amp, one way, 1 module, 230 volts AC circuit complete all as specified and directed.

Supply and fix modular bell switch 6 Amp, one way, 1 module, 230 volts AC circuit complete all as specified and directed.

Supply and fix modular socket, 6 Amp, 2/3 pin combined, 2 module, 230 volts AC circuit complete all as specified and directed.

Supply and fix modular socket, 6 /16 Amp, 2/3 pin combined, 2 module, 230 volts AC circuit complete all as specified and directed.

Supply and fix modular fan regulator 120 W 2 module complete all as specified and directed.

S & F buzzer, ding dong AC 230 Volt single pole complete as specified.

S & F in replacement elegantly industrial general purpose box type luminaire, 1x20 Watt, designed box type LED luminaries, CRCA sheet steel housing with white reflector cover fitted to the body with decorative end covers complete with spring loaded rotor type lamp holders, connected block with and including 01 No LED lamp 20 Watt and all accessories, pre-wired and connecting the same to ceiling rose with & including three core PVC insulated and sheathed copper conductor 23/0.0076 cable including all accessories and fixing arrangement for fixing the light fitting to walls / roof surface over and including 2 Nos PVC square box complete all as specified and directed.

S & F in replacement 10 W mirror light having indirect up down light for mirror and as well light application with CCT 6000K, including LED Bulb/Module and Electrical connection with 3 core flexible wire of appropriate size from ceiling rose to the tubelight fitting, all as specified and directed.

S&F lamp holder PVC / Polycarbonate type with cord grip cap suitable for LED lamp fitting complete all as specified and directed.

Taking down carefully MCBs, Metal clad plug, distribution boards/main switches of any type and size and S & F sheet metal enclosure powder painted for MCB DB SPN 08 way double door with IP-42 protection with Din rail and busbar complete all as specified and directed.

Supply and fixing MCB SPN, 6 to 32 Amps in `C’ series having current rating 10 KA complete all as specified and directed.

S&F MCB single pole, 6 to 32 Amps in `C’ series having current rating 10 KA complete all as specified and directed

Taking Down Old Unserviceable Submain wiring complete including all accessories and making good the disturbed surfaces all as specified and as directed.

M/L for Sub main wiring with 2 runs of PVC insulated unsheathed multi stranded single core copper conducter 6 Sqmm drawn through PVC conduit/casing capping including accessaries with 2.5 sqmm PVC insulated earth wire fixed to the existing wall with saddles, screws etc after removing the unserviceable wiring and connecting up ,all as directed. Note: 2 runs of cable and one run earth wire and conduit/Casing & Caping will be measured as one length.

M&L for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level (with top edge of earth plate not less than 1.5 metre below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe medium grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia medium grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick precast RCC cover in 1 : 2 : 4 type B-1 with 3 Nos 8 mm dia TMT bars both ways with 12mm dia round bar handle complete all as specified & directed. NOTE: Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item and additional earth GI earth wire/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item of Schedule `A’

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc for laying of cables, erection of poles, struts/ stays etc not exceeding 10 sqm on plan and getting out in soft loose soil.

Returning, filling in, including spreading leveling watering and well ramming in layers not exceeding 25 cm in any type of soil.

Removing excavated materials to a distance not exceeding 50 m and depositing where directed, at a level not exceeding 1.5 m above the starting point in soils.

M & L for sand filling in trenches for cushioning of LT cables punning after filling complete as specified and as directed. Note: Punned thickness shall only be measured and paid

Supply and lay un-reinforced precast concrete cable cover , class , LV , Type I flat size 250 x 150 x 40 mm laid dry in treches over under ground cables.

S & F GI pipe, light grade, of size 50 mm dia including necessary fittings laid in trenches/fixed on wall/pole for LT cable protection and taking down the old GI pipe, complete all as speicifed and directed for cable protection .

Supplying ,Laying, jointing and testing new XLPE insulated, armoured, heavy duty, LT aluminum conductor cable 1100 volts grade ,laid in trenches/ducts, floors, fixed to walls etc. complete all as specified and directed of size 4 core 16 sqmm complete all as specified and directed