Renovation of admin space and incubation

Annex 1 - Interior civil

OD: Toughened Glass Partition : Providing and fixing 10 mm toughened glass (Saint Gobain)partition system as per approved drawing .Glass to be fixed using SS patch fittings( Dorma Crown/Equivalent).Use silicon sealant wherever necessary. Finish the partition as per approved design. Including cost and conveyance charges of all materials, labour charges etc.,

OD :Toughened Glass Door Providing and fixing door of 10mm thick Toughened glass door (Saint Gobain) with dorma (Crown) patch fittings(Floor Spring, Top patch, pivot Pin, Bottom patch, Corner lock, Handle.Including all cost and conveyance of materials, labour etc complete.

OD:Toughened Glass Door : Double door Providing and fixing door of 10mm thick Toughened glass door (Saint Gobain) with dorma (Crown) patch fittings(Floor Spring, Top patch, pivot Pin, Bottom patch, Corner lock, Handle.Including all cost and conveyance of materials, labour etc complete.

OD : Gypsum Board Partition : Providing and fixing partition up to ceiling height (upto 360cm) consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick Moisture Resistant Board

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm.

OD: Laminate Flush door with Frame : Providing & Fixing Plywood Door with frame as per architect approved drawing . Door frame finished with 19 mm plywood . Shutter frameworks finished with 19mm plywood (IS 710 Grade,BWP Prestige/Equivalent). Both sides of the frame to be finished with 1 mm thick laminate finish (Century/equivalent) using suitable adhesive (Fevicol/Equivalent) 5.5 mm thick glass to be fixed in the door as per design intent. Complete using necessary SS Hinges, Tower bolts, Locks ,handle, Hafele/Ebco/equivalent) etc., Finish the doors with necessary grooves, SS strips etc. if any. Including cost and conveyance of all materials labour charges etc. complete as per drawing.

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum moisture resistant board

OD: Design, printing and installation of graphics onwall with Digitally reproduced art work printed on self adhesive vinyl film and installed over existing surface of partition/panelling as per details.

OD: Etching Sticker: Providing and fixing etching sticker on toughened glass as per architect approved design including cost and conveyance of all materials labour charge etc complete

15.7.4: Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge. In cement mortar

15.23.2:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm

11.38:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

OD:Epoxy Grouting : Grouting the joints of flooring tiles having joints of 3mm width ,using epoxy grout mix 0.70kg of organic coated filler of desired shape (0.10 kg of hardener and 0.20 kg of resin per kg) including filling/grouting and finishing complete as per direction of Engineer in charge. Size of Tile 300x300mm.

NDSR: Floor Carpet :Providing and laying synthetic carpet Rosetta or equivalent made of 100%PP and not less than 500 gsm pile weight. The carpet shall be fire retardant and stain proof. The total thickness of carpet sheet shall not be less than 7 mm and completely waterproof resilient backing. The fixing on floor shall be done with suitable glue as per manufacturer's specification.

50.6.1.5: Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

NDSR: Calcium Silicate Grid ceiling- Providing and fixing calcium silicate false ceiling tiles at all heights of size 595x595mm of approved texture 6mm thick design and pattern in true horizontal level suspended on interlocking T grid of hot dipped allaround galvanized iron section oh 0.33mm thick(galvanized @ 120gsm)comprising of main t runners of 15x32mm length 3000mm,cross T of size 15x32 of length 1200mm and secondary intermediate cross T of size 15x32 mm of length 600mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanized @ 80gsm) 50mm long 8mm outer diameter M-6 dash fastners 6mm diameter fully threaded hanger rod up to 1000mm length and L shape level adjuster of size 85x25x2mm spaced at 1200mm center to center along main T. the system should rest on peripheri walls/partitions with the help of GI perimeter wall angle size 24x24x3000mmm made of 0.4mm thick sheet to be fixed to the wall with help of plastic raw plug at450mm center to center and 40mm long dry wall ss screws. The exposed bottom portition of all T sections used in false ceiling support system shall be pre painted with polyster baked paint, for all heights. the work shall be carried out as per specification, drawings and as per directions of the engineer in charge.

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete

Acoustics

Absorptive Ceiling Treatment:Supply and Installation of compressed glassfibre with white colour textures finish , Glassfibre core, fully encapsulated (rear side also) ceiling tile of size 595x595x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 grid system. The T15 Grid system of 600x600mm module shall include wall angle with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 having flange width 15mm, length 1200mm is then interlocked into the pre-cut slots in the Main T15 at 600mm centers in the direction perpendicular to the Main T15. Finally Cross T15 having flange width 15mm, length 600mm are then interlocked into the pre cut slots in the 1200mm Cross T15 at 1200mm centers and in direction parallel to the Main T15. Glassfibre tile of size 595x595x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind panels are orianted in one direction to achieve uniform shade. Technical Parameters: • Core - Glassfibre • Fire – Class 1 & P • Acoustics – NRC 0.9 • Climate (OC RH) – 40, 95 • Termite resistance – Yes • Green (RC %) – 35 • Hygiene (VoC, Clean room) – Low, Class 3 • Strength, Load capacity (Kg) - Antisag

Supply and installation of acoustic edge panels, in ebony shade, galvanised mild steel (GMS) core , with cell size of 150x150, 0.5mm thk, web size 50mm height,15mm width which are suspended by using 0.3mm thick TrelisT15 metal grid system. Cubix T Panels can be assembled at site by engaging main track and cross track,50mm height and 15mm width, into one another with the slots provided.Slots will be at 150mm to give cell size of 150mm. Thus formed Cubix T panel of 595x595mm size is then suspended with skelet trelis T15 grid system. Skelet TrelisT15 ceiling grid system of 600x600mm module includes Skelet WA15W30,sectional thickness 0.4mm, with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Skelet MT15W36,sectional thickness 0.3mm, with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15W12,sectional thickness 0.3mm, with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally Skelet CT15W06,sectional thickness 0.3mm, with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600x600mm module. Cubix T, steppe edge panels shall be placed into the grid size of 600x600mm. Technical Parameters : • Fire (Class) – A • Acoustics – na • Climate (°C, RH) – 50, 90 • Light reflectance (%) – Low • Green (VOC, RC %) – Low, 25

Supply and installation of acoustic nubby, of hexagonal shape, 30mm thk of 1000mm diameter,which are having glassfibre core, textured finish and are fully encapsulated. Panels are having density 100-120 kgs/m3 and weight 3-3.6kg/m2. Each panel is provided with 4 sets of accessories containing spring hooks, levelling clip and hanger wires. Springs to be rotated and anchored at back of each panel at four points to hold the panel stable. Supplied hanger wires to be first dropped from the beam/slab/truss to desired height with suitable cleats/anchor bolts. Acoustic hexagonal panels are then suspended using spring hooks and hanger wires and levelled into position with supplied levelling clips.Cleats and anchor bolts. Technical Parameters : • Fire (Class) – 1 & P • Acoustics – NRC upto 0.9 • Thermal conductivity (W/mk)– 0.07 • Climate (°C, RH) – 45, 95 • Light reflectance (%) – 85 • Green (VoC, RC %) – Low, 35

Absorptive Wall Treatment:Supply and installation of Stretch wall fabric system by using FR Grade acoustic fabric of size 1700mm width, shall be stretched by using wooden base 12mm thick, rigid vinyl Stretch Tracks half wrap/full wrap 15mm and Midseam 15mm, woodfibre , synth polyfibre infill with requisite accessories & tools. Wooden base 12mm is first installed on the woodfibre along the marking lines with metal fasteners inserted at 300mm centers . FS15 tracks to be installed on wooden base, after applying Stick adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks. The GI strut system includes GI Cross channel having thickness 0.45mm, length 3600mm, knurled web 40mm, depth 25mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centers. .Woodfibre is square edge magnesite bonded pinewood fiber panels of size 600x1200x15mm having density 400kg/m3, weight 4kg which is fixed to Cross Channel 25mm . Long edge of panels should be perpendicular to length of Cross Channel. . Synth polyfibre 1000gsm 25mm thick adhered on woodfibre panel by using adhesive. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note -minimum 50mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600mm. Technical Parameters : • Core - pinewoodfibre & polyfibre • Fire – 1 • Acoustics – NRC 0.85 • Climate (OC RH) – 49, 90 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 1

Anutone Slats - Wall (upto 80cmm rom floor ) Supply & installation of Slats made of pinewood E1 grade fiberboard, Melamine laminated finish, groove perforated slats L16-2 - (2mm grooves Slats @16mm centres) backlined with black acoustical fleece, tongue-groove edge for a seamless look, of size 128x2440x16mm thick having base density 700Kg/m3, weight 12Kgs/m2 installed by using GI strut system. The GI strut system includes GI Cross channel having thickness 0.45mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centers. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is then fixed perpendicular to the CC25with the help of fasteners at every 400mm centers. Slats of size 128x 2430x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs bothways.Panels shall be backlined with acoustical infill of Synth PF 5x25mm thick adhered to the wall using Stick adhesive. Technical Parameters : • Core Variants - Pinewood E1 Fibreboard • Fire – Class 1 & P • Acoustics – NRC upto 0.75 • Climate (OC RH) – 50, 70 • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 1 • Strength, Load capacity (Kg) - Ball-Impact

Partition/DRYWALL:Supply and installation of magnesia drywall partition system (having high water & fire resistance) which includes one layers of Maganesia board Square edge of size1200x2400x12mm having density 1000kgs/m3, weight 12kg/m2 fixed on the either side of GI strut channel framework. Framing: Framework includes Floor/Head channels having thickness 0.55mm, length 3600mm, equal flanges of 32mm and web of 50mm fixed to floor and ceiling with suitable fasteners at 300mm centers staggered. Noise and fire rated silicon sealant to caulked along the perimeter of the partition frame before fixing channels. Then Stud channel having thickness 0.75mm, length 3600mm, unequal flanges of 34/36mm and web of 48mm should be placed into the floor/head channel positioned vertically at 600mm centers. Extra reinforcement to be provided at openings (doors, windows, etc). Frame cavity insulation: Synth polyfibre having thickness 50mm, width 600mm, density 1000gsm filled between the Studs and held in position by using chicken wire mesh/cross bracings/pasting on one side of the boards. Boarding : The Maganesia board 12mm thick should be fixed on one side of the Stud framework in a staggered (ashlar or brick) pattern by using suitable metal fasteners at 300mm centers. Same procedure to be followed on other side of the framework to give one layers tufbloc on either side of framework. 4mm gap should be maintained between boards on all sides of Tufbloc.Jointing : 4mm gap to be filled by using seam kit as per recommendations. Technical Parameters of Maganesia board ; • Core - Magnesia • Fire – upto 150 minutes • Acoustics – STC upto 44-50 • Climate (OC RH) – 50, 99 • Termite resistance – Yes • Moisture Absorption - 6.8% after 2hrs and 11.3% after 24hrs soaking • Wet Expansion - < 0.02% from ambient to saturation • Dry Contraction - ≤ 0.02% from evaporation • Moisture Movement - 0.02% • Light reflectance – 80 % • Green (RC %) – 30 • Hygiene (VoC, Clean room) – Low, Class 1 • Strength - Antisag • Impact - 4kg hammer 175mm

Wall Absorptive Panel :Supply and installation of fabric finish , polyfibre panels, core-pigmented, high-density, Synthpolyfibre rigid panels of size 1200x2400x9mm thk, volume density 210 - 230kg/m3, weight 1.9 - 2.1kg/m2 installed by using Strut framework system.The Strut framework systems includes Strut Cross Channel having thickness 0.55mm, length 3600mm, knurled web 50, depth 25mm and equal flanges 15mm is fastened to wall positioned horizontally in a regular manner at 600mm c/c. Woodfibre , Square edge, Magnesite bonded pinewood fibre core tiles of size 600x1200x10mm, density 400 kgs/m3, weight 6kg/m2 are fastened to Strut Cross channel with suitable fasteners. Longer edges of the panel should be perpendicular to Strut CC25 Cross Channel. Synth polyfibre Panels are then adhered to woodfibre behind with stick adhesive.Technical Parameters of Synth Polyfibre ; • Fire (Class) – B • Acoustics – NRC 0.4 (For A mounting) • Thermal conductivity (W/mk)– na • Climate (°C, RH) – 50, 99 • Light reflectance (%) – Colour Dependant • Green (VoC, RC %) – Nil, 30 Technical Parameters of woodfibre: • Fire (Class) – 1 & P • Acoustics – NRC 0.73 (For 25mm C50 Mounting) • Thermal conductivity (W/mk)– 0.1 • Climate (°C, RH) – 50, 95 • Light reflectance (%) – 80 • Green (VOC, RC %) – Low, 35

Water supply & sanitary system

NDSR : Providing and fixing studio SW ceramic water closet (European type) with seat ,lid & flush tank, and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

NDSR : Providing and fixing wall hung wash basins with half pedestal, brass pillar taps, C.P. brass waste of standard pattern(bottle trap), including painting of fittings, cutting and making good the walls wherever require: White Vitreous China Ovel wash basin size 460 x 350 x 180 mm (with half pedestal height 465 mm) with single C.P.brasspillar taps

NDSR : Providing and fixing brass bib cock of approved quality

NDSR : Providing and fixing brass angle stop cock 15 mm nominal bore, weighing not less than 85 gms

NDSR : Providing and fixing threaded waste Coupling. Waste coupling 32 mm dia.

NDSR : Providing and fixing uplasticised PVC connection pipe with brass unions: 20 mm nominal bore

50.18.8.2.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chased and making good the wall etc. 20 mm pipe 12 Kgf/cm2

50.18.8.7.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.8.9.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.20.2: Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

50.18.9.20.4: Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.20.5: Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee

50.18.9.22.2: Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.4: Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5: Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

18.7.2: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall 20 mm nominal outer dia pipes

Annex 2 - Furniture

Linear Workstations : Size 1200 L x 600 W X 750 H mm, Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Under structure : Necessary wire managent so that switches to be mounted on wire tray below work top and acccesed using soft closing access flap, Accessories (excluding switch and socket) , Leg : Aluminium extruded powder coated leg and MS powder coated edge beams. Front separation above the table top, 300mm height acrylic screen partition on table top with neccessary partition holder at the base

Pedestal storage : PreLaminated Mobile pedestal unit with 1 drawer and a shutter. Upper 1 box drawer + 1file shelf and profile handle. Size : 400W x 450D x650H. All edges are lipped with 2mm and 0.8mm PVC edge band. Bottom shall be provided with castor for mobility.

Manager cabin L shape tables : Size (1500 L x 600 W X 750 H) + (900 L x 500 W x 750 H) mm. Vertical covering and Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Outer sides should be covered from table top to floor. Side storage with soft closing shutters and drawers with profile handles.

CEO Cabin L shape table :( Size :- 2100 X 2100 mm, Main table 2100x900, Return 1200x600) Front table with size (2100 L X 900 W X 750 H) mm. Vertical covering & Top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Side storage cum table 1300L X 600 W X 750 H mm. Vertical covering & Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Side storage as per the drawing with pre laminated board with door, and drawers with full length profile handle and lock and soft closing guides.

Conference room table : Size : 3800 L X 1150 W X 750 H mm. Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band.Under structure : Necessary wire managent so that switches to be mounted on wire tray below table top and acccesed using soft closing access flap (atleast 3 openings ), Accessories (excluding switch and socket). Leg : Central supports with MS powder coated leg and beams.

Meeting room table : Size : 3000 L X 1150 W X 750 H mm. Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band.Under structure : Necessary wire managent so that switches to be mounted on wire tray below table top and acccesed using soft closing access flap (atleast 2 openings ), Accessories (excluding switch and socket). Leg : Central supports with MS powder coated leg and beams.

Meeting room table : Size : 2200 L X 1000 W X 750 H mm. Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band.Under structure : Necessary wire managent so that switches to be mounted on wire tray below table top and acccesed using soft closing access flap (atleast 2 openings ), Accessories (excluding switch and socket). Leg : Central supports with MS powder coated leg and beams.

Discussion room table : Size : 1500 L X 1000 W X 750 H mm. Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band.Under structure : Necessary wire managent so that switches to be mounted on wire tray below table top and acccesed using soft closing access flap (atleast 2 openings ), Accessories (excluding switch and socket). Leg : Central supports with MS powder coated leg and beams.

Reception table : Size 2000 L X 750 W X 750 H mm. Vertical covering and Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Necessary wire managent so that switches to be mounted on wire tray below table top and acccesed using soft closing access flap (atleast 2 openings ), Accessories (excluding switch and socket).

Square table : Size : 600 W X 750 H mm. Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band.Vertical support used in the system shall be fabricated with metal tube with epoxy powder coating

Round table : Size : 800 mm dia with 750 mm height. Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band.Vertical support used in the system shall be fabricated with metal tube with epoxy powder coating

Foldable laptop table of size 500x500mm.Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Bottom shall be provided with castor for mobility.

File rack / storages: side storage as per the drawing with particle board finish with door, handle and quality lock. All edges are lipped with 2mm and 0.8mm PVC through feed edge banding method. Bottom shall be provided with proper plinth support, allowing ease of cleaning. hardware: EBCO. Size : 1500 x 450 x 1800 mm

File rack / storages: side storage as per the drawing with particle board finish with door, handle and quality lock. All edges are lipped with 2mm and 0.8mm PVC through feed edge banding method. Bottom shall be provided with proper plinth support, allowing ease of cleaning. hardware: EBCO. Size : 3300 x 450 x 1800 mm

File rack / storages: side storage as per the drawing with particle board finish with door, handle and quality lock. All edges are lipped with 2mm and 0.8mm PVC through feed edge banding method. Bottom shall be provided with proper plinth support, allowing ease of cleaning. hardware: EBCO. Size : 4300 x 450 x 1800 mm

File rack / storages: side storage as per the drawing with particle board finish with door, handle and quality lock. All edges are lipped with 2mm and 0.8mm PVC through feed edge banding method. Bottom shall be provided with proper plinth support, allowing ease of cleaning. hardware: EBCO. Size : 900 x 450 x 1800 mm

Medical examination couch for sick room: Size : 1850 L X 600 W X 820 H. Back rest adjustable by crank mechanism. Framework made of Mild Steel Epoxy coated finish with step stool and couch full storage

Workstation chairs: Mid back with armrest, multiple locking system, Seat upholstered with PU Foam & back with mesh. Gas lift for seat and height adjustment, Nylon base with castor

Executive conference / meeting chair:High back Nylon Base: 330mm Synchronized simple/multi-function mechanism Electro plated/Powder coated TUV -CLASS 4 Gas spring: 120mm Seat & back upholstered with PU leather.

Manager cabin chairs :High back. Polished Aluminium base: 330mm Synchronized Multi -function Knee -tilt mechanism. Gas spring. Adjustable armrests with PU pads. Seat upholstered with PU foam & back upholstered with Imported nylon mesh.

CEO chair : EXECUTIVE CHAIR :Polished Aluminium Base:330mm Seat & back with mesh. Height and angle adjustment head rest. Back rest Height Adjustment.Flexible Lumbar Support.Seat Height adjustment.Seat depth adjustment.Back rest angle adjustment.Armrest Height adjustment.Arm pad Angle and width adjustment.

Reception chair : High back. Polished Aluminium base: 330mm Synchronized Multi-function Knee,tilt mechanism.Gas spring.Adjustable armrests with PU pads.Seat upholstered with PU foam & back upholstered with Imported nylon mesh.

Visitor chair : Powder coated mild steel frame. Seat upholstered with soft foam & back with mesh : Imported fabrics.

Training room/ ceo cabin chairs: The seat sub-assembly should be made up of 1.2±0.1cm thk plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. the seat can tip-up when not in use and the feature can be used while stacking the chairs horizontally. The back sub-assembly should be made up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The back flexing features allows the back to tilt by 9c±2' to aid the user in adopting a comfortable reclining posture.Both these sub-assemblies should be fixed to the tubular structure.Tubular frame structure: the powder-coated 4 leg structure. The legs should be provided with injection-moulded adopter bush in black nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use_ the chairs can be stacked horizontally when not in use.Polyurethane foam: the polyurethane foam should be moulded with density = 70.0 ±8.0 kg/m3 and hardness = 20 ±2 for seat & 16 ±2 for back at 25% compression. Armrests: the armrest structure should be made up of tube welded to the tubular frame structure and having a scratch-resistant tant abs arm top.Twin wheel castors:the twin wheel castors should be injection moulded in black

Discussion chairs

Sofa : 1 seater with fabric covering : the seat should be made of pu foam with density 32 ± 2 kg/cu.mtr having an additional top layer of j pu foam with density 28 ± 2 kg/cu. seat should be upholstered with fabric or leatherette. 2) back foam: the back should be made of pu foam with density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette understructre : understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood. Width (W): 86.0 CM. Depth (D): 92.0 CM. Height (H): 82.0 CM. Seat Height (SH): 45.0 CM.

Sofa : 2 seater with fabric covering : the seat should be made of pu foam with density 32 ± 2 kg/cu.mtr having an additional top layer of j pu foam with density 28 ± 2 kg/cu. seat should be upholstered with fabric or leatherette. 2) back foam: the back should be made of pu foam with density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette understructre : understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood. Width (W): 146.0 CM. Depth (D): 92.0 CM. Height (H): 82.0 CM. Seat Height (SH): 45.0 CM.

Sofa : 3 seater with fabric covering : the seat should be made of pu foam with density 32 ± 2 kg/cu.mtr having an additional top layer of j pu foam with density 28 ± 2 kg/cu. seat should be upholstered with fabric or leatherette. 2) back foam: the back should be made of pu foam with density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette understructre : understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood. Width (W): 205.5 CM. Depth (D): 92.0 CM. Height (H): 82.0 CM. Seat Height (SH): 45.0 CM.

Round puffy stool with 400mm Dia and 450mm high from the floor.seat should be upholstered with fabric

Bean bags : King size with high quality bean and leather

Discussion modules : Interior discussion module. Size Height 222 cm (87.4 in) x width 220 cm (86.6 in) x depth 120 cm (47.2 in). Customizable, easy to assemble and relocate, large range of color options, LED lighting, three power sockets. Structure is combination of steel, Aluminium ,wood & Engineered wood. Acoustic interior with ventilation fan, laptop foldable mounting table. adjustable seating. Both sides are covered with toughened glass with a single panelled glass door

Annexure III ELECTRICAL Wiring

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Group B

Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/ PVC conduit including dismantling as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 16 amp socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, along with modular base & cover plate for modular switches in recess etc. as required without GI box/PVC box.

6 Module

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

3 Module (100mmX75mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Ironcable tray cable tray with perforation not more than 17.5%, in convenient sections,joined with connectors, suspended from the ceiling with G.I. suspenders includingG.I. bolts & nuts, etc as required. Make : OBO or equivalent

MS perforated cable tray Hot Dipped Galavanized 100mmx60mmx2 mm

MS perforated cable tray Hot Dipped Galavanized 150mmx60mmx2 mm

MS perforated cable tray Hot Dipped Galavanized 200mmx60mmx2 mm

MS perforated cable tray Hot Dipped Galavanized 300mmx60mmx2 mm

MS perforated cable tray Hot Dipped Galavanized 400mmx60mmx2 mm

MS perforated cable tray Hot Dipped Galavanized 500mmx60mmx2 mm

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 8 way (8+24) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 8 way (8+24) - three phase double cover (IP 42/43)

Supplying and fixing following rating, double pole, (single phase and neutral), 415V, Residual Current Circuit Breaker with Overcurrent protection (RCBO), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps RCBO

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker with overcurrent protection (RCBO), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 32 amps RCBO

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

35 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

10 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

16 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

Lighting

Supply of LED Slim Donwlighter Round 12W Surface Mounted min 950 System Lumens , Aluminium die cast LED Light Fixture other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of LED pendant Mounted 12W (+/- 2W) min 1200 System Lumens ,white finish CRCA Powder coated,HET Plastic diffuser,50000 Hours ,THD<10% 5700K CCT other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of LED Ring light fixture 35W(+/- 10%) min 3500 System Lumens 600MM Dia ,THD <10% driver efficiency ≥85%,Extruded Aluminium housing powder coated Suspended Mount Type with min 2.5KV Surge protection other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of LED Ring 40W(+/- 10%) min 4000 System Lumens 800MM Dia ,THD <10% driver efficiency ≥85%,Extruded Aluminium housing powder coated Suspended Mount Type with min 2.5KV Surge protection other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of LED Slim 30W(+/- 10%) min 3750 System Lumens ( +/- 10%) 800MM Dia ,THD <10% driver efficiency ≥85%,Extruded Aluminium housing powder coated Suspended Mount Type with min 2.5KV Surge protection other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of 20W 4ft, High efficiency long life Linear suspended luminaire Continuous end to end type with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 115lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2300lm. other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of 20W 4ft, High efficiency long life Linear suspended luminaire standalone with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 115lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2300lm. other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of 40W 8ft Continous type , High efficiency long life Linear suspended luminaire standalone with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 115lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 4600lm. other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of LED pendant Mounted 18W (+/- 2W) min 1800 System Lumens ,white finish CRCA Powder coated,HET Plastic diffuser,50000 Hours ,THD<10% 5700K CCT other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of 20W 4ft, High efficiency long life Linear suspended luminaire Continuous end to end type with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 115lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2300lm. other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of 20W 4ft, High efficiency long life Linear suspended luminaire standalone with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 115lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2300lm. other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Supply of 40W 8ft Standalone type , High efficiency long life Linear suspended luminaire standalone with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 115lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 4600lm. other accessories, including provision to connect with 1.5sqmm wires & earthing etc

Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Annexure IV HVAC works CHW CASSETTE FCU

Supply, installation, testing and commissioning of the following Fan coil Unit 1.0 TR with Pre-filter, Chilled water coil (copper tube and aluminium fins construction), Fan section, Chilled Water Pipe Connections, Vibration dampers etc. complete as per specifications as required. with complete accessories including remote control drain pumps tc.

Supply, installation, testing and commissioning of the following Fan coil Unit 1.5 TR with Pre-filter, Chilled water coil (copper tube and aluminium fins construction), Fan section, Chilled Water Pipe Connections, Vibration dampers etc. complete as per specifications as required. with complete accessories including remote control drain pumps tc.

Supply, installation, testing and commissioning of the following Fan coil Unit 2.0 TR with Pre-filter, Chilled water coil (copper tube and aluminium fins construction), Fan section, Chilled Water Pipe Connections, Vibration dampers etc. complete as per specifications as required. with complete accessories including remote control drain pumps tc.

Supply, installation, testing and commissioning of the following Fan coil Unit 2.5 TR with Pre-filter, Chilled water coil (copper tube and aluminium fins construction), Fan section, Chilled Water Pipe Connections, Vibration dampers etc. complete as per specifications as required. with complete accessories including remote control drain pumps tc.

Supply, installation, testing and commissioning of the following Fan coil Unit 3.0 TR with Pre-filter, Chilled water coil (copper tube and aluminium fins construction), Fan section, Chilled Water Pipe Connections, Vibration dampers etc. complete as per specifications as required. with complete accessories including remote control drain pumps tc.

Supply, installation, testing and commissioning of the following Fan coil Unit 4..0 TR with Pre-filter, Chilled water coil (copper tube and aluminium fins construction), Fan section, Chilled Water Pipe Connections, Vibration dampers etc. complete as per specifications as required. with complete accessories including remote control drain pumps tc.

CHILLED WATER PIPING

Supply, Leading to Site, Installation of 32 mm thick Supplying, laying /fixing, testing and commissioning of following thickness cross link closed cell preformed sections of polyethylene insulation Nitrile rubber applied aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints etc. as per specifications and as required complete in all respect . Insulation with nitrile rubber of thickness 32mm on existing pipe nitrile rubber with foster for existing chilled water piping.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS : 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. Chilled water piping of nominal size-65mm dia. (32mm thick nitrile rubber insulation)

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS : 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. Chilled water piping of nominal size- 50mm dia. (32mm thick fiber glass insulation) COST

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS : 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. Chilled water piping of nominal size 40mm dia. (32mm thick nitrile rubber insulation)

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS : 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. Chilled water piping of nominal size-32mm dia. (19mm thick nitrile rubber insulation)

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS : 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. Chilled water piping of nominal size-25mm dia. (19mm thick nitrile rubber insulation)

Supply, Installation, testing and commissioning of Valve Package and Digital Thermostat for FCU

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of drain water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Chlorinated Polyvinyl - Chloride (CPVC) pipe 25 mm outer dia

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of drain water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of class 'O' insulation applied by adhesive confirming to standard specifications and finally applying 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing feltstrip (as per IS:1322 as amended up to date) at joints and repairing of damage to building etc. as per specifications and as required complete in all respect. Chlorinated Polyvinyl - Chloride (CPVC) pipe 32 mm outer dia

DUCTING

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 Thickness 1.00 mm sheet

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 Thickness 0.80 mm sheet

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 Thickness 0.63 mm sheet

Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying and Fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

VOLUME CONTROL DAMPERS

Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

Supply and fixing of class 'O' type closed cell elastomeric Nitrile rubber insulation of the following thickness for thermal insulation of ducts.The material should conform to Class 1 rating for surface spread of Flame as per BS 476 Part 7 and also pass Fire Propogation requirement as per BS 476 Part 6 to meet the Class O Fire category.The material should be fibre free. The density of the same shall be within 40-60 Kg/m3.The material should have a thermal conductivity not exceeding 0.036 W/mK at 0 Degree C and Moisture Diffusion Resistance Factor should be minimum 7000 according to EN 12086. Make:Armaflex/Kflex/Equivalent.

Supply and installation of Acoustic insulation/ AHU Plant room, Material shall be open cell Nitrile Rubber.The Thickness of the material shall be 10 mm.

Supply and installation of Acoustic insulation/ AHU Plant room, Material shall be open cell Nitrile Rubber.The Thickness of the material shall be 20 mm.

Supply, Installation, Testing and commissioning of VAV system for cabins

Supply, Installation, testing and commissioning of 80 mm Dia Non spring return 2 way valve flange type with actuator

Supply, Installation, testing and commissioning of Digital Thermostat

Annexure V

Total cost for demolition, removal and complete disposal of interior fit outs such as furniture, glass, partitions, AC ducts, electrical fixtures, sanitary fittings etc at site to be paid by KSUM to contractor (Addition)

Total cost of salvage value offered to KSUM for the serviceable materials/scrap removed (Deduction)