Repair/Renovation of Divisional Office building JKSPDC Sopore

Amount

Dismantling old plaster or cement concrete flooring, skirting , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Brick work with common burnt clay (non modular) bricks of class designation -75 in foundation and plinth including curing in cement mortar 1:4(1 Cement : 4 coarse sand).

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand).internal walls of Bathrooms.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete.(Size of tile 600x600 mm).

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(Size of tile 600x600 mm).

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls completeincluding disposal of rubbish to the dumping ground within 50 meters leadWith cement mortar 1:4 (1 cement : 4 fine sand).

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work.

Varnishing with Varnish of approved brand and manufacture two or more coats of glue sizing with Spar varnish on an under coat of flatting varnish.

12 mm Cement plaster of mix 1:6(1 Cement: 6 Fine sand) of external walls.

Finishing walls with acrylic smooth exterior paint of required shade on new work (two are more coats applied @1.67litre/10sqm over and including base coat of water proofing cement paint [email protected]/10Sqm).

Providing and fixing 35 mm thick factory made laminated vaneer lumber door shutter conforming to IS 14616 and TADS 15:2001(Part-b) incl. M.S pressed Butt hinges bright finished of requiured size with necessary screws as per directions of Engineer-in- charge and panelling with panels.12 mm thick plain grade-1, medium density flat pressed three layer particle board FTP-I or graded wood particle board FPT-I IS:3087 marked bonded with BWP type syntehitc resin adhesive as per IS:848.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.(First class kail wood).

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction ofEngineer-in-charge : (First class kail wood)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Renewing glass panes, with wooden fillets wherever necessary and Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Providing and fixing stainless steel Double bar dotted railing made of heavy duty hollow tubes, including welding ,grinding ,buffing , polishing and making curvature and fitting with necessary stainless steel nuts and bolts complete , including fixing the railing with necessary accessories and stainless steel dash fasteners , steel bolts, carriage etc. of required size all complete.

Providing and Fixing stainless steel double dotted Master Pillars made of heavy duty hollow tubes, including welding ,grinding ,buffing , polishing and making curvature and fitting with necessary stainless steel nuts and bolts complete , including fixing the railing with necessary accessories and stainless steel dash fasteners , steel bolts, carriage etc. of required size all complete.

Providing and fixing door and window items of approved quality incl.necessary screws complete all.

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :complete.(Size= 250x16 mm)

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :(100x10 mm).

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper (Single rubber stopper), ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screws etc. complete.

ELECTRICAL FITTING:-Concealed Electrical/ PVC Channel fitting(wherever required) point. Includes all material & labour work. End to end wiring & installation of Modular switch board & Modular Switches Etc,testing and commisioning. Brands considered - Anchor Roma switch, Polycab/Finolex wires/Havells.

Providing,fixing,installation,testing and commissioning of electrical fittings (light points) including Service/ feeding lines with 1.5 Sq.mm FRLS&PVC insulated Copper conductor single core cable wire for lighting points and 2.5 sq.mm PVC insulated multi strand copper wire for Sub-Main wiring alongwith earth wire, 06 Amp 3 pin sockets, Including Modular type Switch, Smart LED solution Metal water proof outdoor 24 watt lights, Philiphs 9 watt Ceiling Secure recessed ceiling lamps with all acceriories,Inverter lines ,Wiring for circuit/ Main & Sub Main wiring alongwith earth wire ,including holders, ceiling rose on the junction box/PVC Block, hangers and fancy fittings PVC Conduit/ Channel with bends , junction boxes,06 Amp S Pole MCB, 10 Amp DP MCB, 2 way DB for housing MCB and Hylem sheet with wooden box recessed in walls with accessories of approved quality such as Havells, Anchor etc, Inculding cost of cutting chases and making good the walls/Celing ,including telephone cable for 03 rooms all complete .

Providing,fixing,installation,testing and commissioning of electrical fittings Heating points fed by a separate Heating circuit and controlling switches, feeding Lines 4 Sq.mm size above, Main & Sub Main Service Lines with 10 Sq.mm size above FRLS PVC insultaed copper conductor single core , Inverter lines and fancy fittings 16 Amp Modular Switch & sockets combined, PVC Conduit/ Channel with bends , junction boxes, 32 Amp S Pole MCB, 32 Amp DP MCB,2 way DB for housing MCB and Hylem sheet with wooden box recessed in walls with accessories of approved quality such as Havells, Anchor etc, Inculding cost of cutting chases and making good the walls/Celing.

Providing , fixing,Installation, testing and commissioning of ceiling fan,including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. including Service/ feeding lines, including 1200 mm fan with ceiling rose & PVC Square block, 350 watts electronic fan dimmer, PVC Conduit/ Channel with bends , junction boxes,06 Amp S Pole MCB, 10 Amp DP MCB, 2 way DB for housing MCB with wooden box recessed in walls with accessories of approved quality such as luxury type Havells, Anchor etc., complete all.

Providing and installation of change over box four Pole 100 Amp of first quality approved (Havells) etc., complete all.

Prividing & installation of single phase 5KW stablizer including all necessary fittings with trip system complete all.

SANITARY / WATER SUPPLY INSTALLATION:- Providing and fixing water closet squatting pan (Indian type W.C. pan) white vitreous china Orissa pattern W.C.pan size of 580 x 440 mm with integral type foot rests , with 100mm sand cast iron P or S trap, 10 liter low level white PVC flushing cistern, including flush pipe of approved makes,with manually controlled (handle lever)conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.

Providing and fixing PTMT towel rail complete with brackets Fixed to wooden cleats with CP brass screws with concealed fitting arrangements of approved quality and color,600mm long towel rail with total length of 645mm,78 mm wide and effective height of 88 mm, weighing not less than 190 grams.

Providing and fixing wash basin with C.I./M.S. brackets, 15 mm C.P. brass pillar taps ,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherevre required white vitreous china wash basin size 630 x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing CP Brass 32 mm size bottle trap of approved quality and make and as per the directions of Engineer-in-charge.

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete.(Semi ridged 40 mm dia.).

Providing and fixing mirror of superior glass(approved quality) of rectangular shape 453 x 357 mm with plastic moulded Frame of approved make and shade with 6 mm thick hard board backing.

Providing and fixing 20mm nominal outer dia pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.(External work including trenching, refilling etc.)

Providing and fixing 3 layer PN-16 pipe, 16mm OD(SDR-7.4) PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.(Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.)

Providing and fixing PPR Unions 20 MM.

Providing and fixing 20 mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end)including necessary all fittings.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make,weighing not less than 1.970 kg.

Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing 15 mm nominal bore with 45 cm length un plasticized P.V.C. connection pipe with PTMT nuts, collars and bush of approved quality and colour.

Providing and fixing of approved quality and manufacture Geyser 50 liter capacity of Racold Including necessary fittings all complete.

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes, all complete

Providing, laying and jointing 100mm dia. soil waste pipe PVC Princes quality B- type inlet end from Latrine pan to septic tank including plain bends of required degree ,single equal junction of required degree with access door, insertion rubber washer 3 mm thick , Collars, P & S / F traps, complete all .

Providing, laying and jointing 75 mm dia. soil waste pipe PVC Princes quality B- type inlet end from Floor tarp to Soak pit including plain bends of required degree ,single equal junction of required degree with access door, insertion rubber washer 3 mm thick , Collars, Floor traps, Including Steel waste coupling, complete all.

Carriage of construction materials from source to site by MT loading and unloading.

Cement lead upto 1Km from Sopore market to Divisional Office.

Sand lead upto 7 Km from Seelu Sopore to Divisional Office.

Timber from local market to site 01 Km lead.

Bricks lead upto 1 Km from Sopore market to Divisional Office.

M/S MUNEER AHMAD LONE

M/S MEHRJ UDDIN BATKALOO

MUBASHR AHAD WANI