REPAIR REPLACEMENT OF LT UG CABLE OH LINE LT POLES CONTROL PANEL BOARD CHANGE OVER SWITCHES AND ALLIED ITEMS AT AF STN NALIYA

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/ loose soil, for laying of under ground electric cable, pipes etc all as directed and specified. Note:(i) Authorised width & depth shall only be excavated, measured and paid as specified in clause 3.2.3 of SSR part II and 19.74.1 of SSR part I for cable/pipe laying portion. (ii) Serviceable PCC /RCC cable cover obtained during excavation shall be stacked separately carefully without any extra cost to the Deptt.

Taking out old unserviceable LT cable of any size any type from trench/duct/ poles / roof/pipe etc and keeping aside for segregation of serviceability. Serviceable cable will be re-laid at same place or other place as required.

Supply and laying, connecting XLPE insulated, armoured, heavy duty electric cable multi stranded aluminum conductors, 1100V grade, of size 16 Sqmm 4core with proper size of lugs and laid in trenches / ducts / through GI pipe / fixed to poles etc complete all as specified and directed by Engr-in-Charge. Note: Excavation earthwork, cable covers, sand cushioning and GI protection pipe shall be measured and paid separately under relevant item.

All as per item No 3 above but of size 35 Sqmm 3.5 core

All as per item No 3 above but of size 70 Sqmm 3.5 core

All as per item No 3 above but of size 95 Sqmm 3.5 core

Re-laying of old serviceable cable of any size obtained from item above. Note: Excavation earthwork, cable covers, sand cushioning and GI protection pipe shall be measured and paid separately under relevant item.

M & L for river bed sand filling in trenches/ ducts 15 cm above cable and 8 cm under the cable for cushioning/protection to cable including spreading, leveling and get thick 18cm after hand punning complete all as specified and directed

Laying only serviceable un-reinforced precast concrete cable cover class LV, Type 1, flat, of 250 mm x 150 mm x 40 mm obtained from trenches, abetting each other with gap between adjacent slab not exceeding 10 mm over under cable for protection complete all as directed.

Supply & laying un-reinforced precast concrete cable cover, class LV, Type 1, flat, size 250 mm x 150 mm x 40 mm abetting each other with gap between adjacent slab not exceeding 10mm over under cable for protection.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exceeding 25cm thick each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point complete all as specified and directed.

M& L for cutting under the road /pavement /hard standing or in any other situation with the manual labour for crossing of U/G cable through it and making both the end good complete all as specified and directed .

Supply and laying GI water tubing of 80 mm bore, light grade, IS-1239 marked with all fittings IS marked and laid in trenches/under roads/in drains with suitable size flat iron/GI clamps, bolts, nuts and washers etc for cable protection, complete all as specified.

Supply and laying GI water tubing of 50 mm bore, light grade, IS-1239 marked with all fittings IS marked and laid in trenches under roads/in drains, fixed to poles/walls with suitable size flat iron/GI clamps, bolts, nuts and washers etc for cable protection, complete all as specified and as directed.

Supply and laying GI water tubing of 40 mm bore, light grade, IS-1239 marked with all fittings IS marked and laid in trenches/under roads/in drains with suitable size flat iron/GI clamps, bolts, nuts and washers etc for cable protection, complete all as specified.

Supply, fixing and testing LT cable jointing kit straight through heat shrinkable type suitable for cable PVC /XLPE insulated armoured heavy duty aluminum conductor 1100V grade LT cable of size 3.5/4 core 16 to 50 sqmm complete all as directed.

Supply, fixing and testing LT cable jointing kit straight through heat shrinkable type suitable for cable PVC /XLPE insulated armoured heavy duty aluminum conductor 1100V grade LT cable of size 3.5/4 core 70 to 150 sqmm complete all as directed.

Supply, fixing and testing LT cable jointing kit straight through heat shrinkable type suitable for cable PVC /XLPE insulated armoured heavy duty aluminum conductor 1100V grade LT cable of size 3.5/4 core 185 to 300 sqmm complete all as directed.

M&L for Cement concrete in pole foundations, coping, filling and mass concrete, type D2 1:4:8 with 40mm graded stone aggregate including dismantling old PCC etc

M&L for Cement concrete in pole foundations, coping, filling and mass concrete, type C2 1:3:6 with 40mm graded stone aggregate including dismantling old PCC etc

Supply & fixing of MS CRCA sheet enclosure of 2mm sheet thickness duly painted, fixing arrangement for housing MCCB including supply and fixing MCCB of capacity 63 Amps, 10KA 4 pole, 415 volts with fixed thermal & magnetic settings including & connections of cables with thimbles/lugs and to existing DB etc complete all as directed.

Supply & fixing of MS CRCA sheet enclosure of 2mm sheet thickness duly painted, fixing arrangement for housing MCCB including supply and fixing MCCB of capacity 100 Amps, 16KA 4 pole, 415 volts with fixed thermal & magnetic settings including & connections of cables with thimbles/lugs and to existing DB etc complete all as directed.

Supply & fixing of MS CRCA sheet enclosure of 2mm sheet thickness duly painted, fixing arrangement for housing MCCB including supply and fixing MCCB of capacity 160 Amps, 25KA 4 pole, 415 volts with fixed thermal & magnetic settings including & connections of cables with thimbles/lugs and to existing DB etc complete all as directed

Supply & fixing of MS CRCA sheet enclosure of 2mm sheet thickness duly painted, fixing arrangement for housing MCCB including supply and fixing MCCB of capacity 200 Amps, 25KA 4 pole, 415 volts with fixed thermal & magnetic settings including & connections of cables with thimbles/lugs and to existing DB etc complete all as directed

S&F in replacement for kiosk box for luminaries, weather proof made out of PVC/HDPE /FRP housing fire retardant, non fusing, shock & rust proof, single piece molded and cover with hinged door, pole mounting type comprising of aluminum TPN bus bar of 60 Amps of minimum size 300x250x150mm, fixed on pole with MS, clamps 30x5mm with necessary nuts, washer complete all as directed. Note. Rate of TPN bus bar and MS clamp inclusive in item rate

S&F in repair service wire 1100 volts grade PVC insulated PVC unsheathed cable multi stranded copper conductor of size 0.75 sqmm 3 core complete all as specified

S&F sintex box of size 450mm x 375mm x 200mm made out of poly carbonate IP-65 protection with poly ethelene gasket and glow wire tested at 960 degree celcius as per IEC 60695-2-11 and thermoplastic gland of suitable size fixed on poles with galvanised clamps (02 Nos on each pole) of F1, 40x5mm made to shape fixed with nut bolts washers etc. Make Sintex or equivalent complete all as specified and directed with following fitments :- (a) Aluminum bus bar of 100Amps capacity fixed on porcelene insulators and insulated with colour sleeves (04 Nos) and connect suitable for 25Sqmm to 35Sqmm cable Note : Cost of clamps and bus bar strips is inclussive in quoted rate

S&F Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut,100mm height, 65mm dia for 1100 volts grade complete all as specified and as drected

S&F Shackle Type, Porcelain, vitreous, white, brown or green insulator including galvanised mild steel straps, washers, insulator bolts, washers and nuts, 1100 volt grade of size 75 mm height and 90mm dia complete all as specified.

S&F in repair danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size

S&F spacers/separator PVC with clamping nut bolts suitable for 2 wire

S&F spacers/separator PVC with clamping nut bolts suitable for 3 wire

S&F spacers/separator PVC with clamping nut bolts suitable for 4/5 wire

Supply and fix maintenance free solar deep cycle batteries designed for long time back up of capacitry 12 volt 65 AH.

Supply and fix mono/polycrystalline MNRE approved solar panels for solar lights of capacity 20 watt 12 volts suitable for 20 watt solar lights

Supply and fix solar lights 20 watt with all accessories suitable for solar panels for solar panels of capacity 20 watt with white lights complete

M & L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below GL with top edge of the plate not less than 1.5 mtr below normal GL and connected to earth plate . Earth plate surrounded by 15 cm thick packed layers of charcoal dust and common salt upto 1.5 meter depth all around the earth plate and connected to earth lead of GI strip 32x6 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel and thimbles and other end of the earth wire connected to Plant/equipment and protected by galvanized iron or steel pipe light grade and water pipe 20mm bore GI medium grade with funnel and wire mesh, including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 3 of MES schedule Pt I of 2009 and also including making test point for testing of earthing made out of gun metal or phosphorous bronze size 75x75x25 mm complete . Note : On testing after completion of earthing if desired earth resistance below 5 ohms is not achieved , the earthing will be redone at no extra cost.

Dismantling of DG Set of capacity 50 KVA and make Crompton Greaves(Location-609 Garud Flt,AF Stn Naliya) from Trolly & transporting of Engine to work shop for complete servicing,repair & overhauling.Dismantling the engine complete by taking out radiator,pump assembly,casing top cover,head assembly,piston,liners,filters ,hose pipes,fuel pipe,fuel pump assembly,exhaust,turbocharger etc for complete overhauling of engine and repair/replacement of unserviceable/wornout parts i.e. piston,piston ring,liners,turbocharger etc complete including oiling,greasing and servicing of all the parts of DG Sets and reassembling complete and testing DG Sets for proper functioning,transportation of DG Sets to its site to its original position including connecting all incoming and outgoing cables and its on load testing complete all as per specification and satisfaction of Engineer-in-charge. (a) Supply only in replacement Piston(Qty-03 nos); (b)Supply only in replacement Piston ring(Qty-03 nos);(c) Supply only in replacement Cylinder Liner(Qty-03 nos);(d)Supply only in replacement CR Bearing; (e) Supply only in replacement Inlet valve(Qty-03 nos);(f) Supply only in replacement Exhaust valve(Qty-03 nos);(g) Supply only in replacement Valve Guide(Qty-06 nos);(h)Supply only in replacement Valve seat in inlet(Qty-03 nos);(i) Supply only in replacement Valve seat in exhaust(Qty-03 nos);(k)Supply only in replacement Set of 'O' Ring(Qty-9 nos);(l) Supply only in replacement Valve spring(Inner)(Qty-03 nos);(m) Supply only in replacement Valve spring(Outer)(Qty-03 nos);(n) Supply only in replacement CR Bush;(o)Supply only in replacement new Block set suitable for housing of Piston,cylinder and valve assly complete;(p) Supply only in replacement Lubricating Oil filter;(q) Supply only Engine oil 20W40 grade;(r) Supply only premixed Coolant for radiator.;(s) Cylinder Head Repowering;(t) Servicing and Calibration of Fuel Injection Pump(FIP);(u) M&L for taking out existing Turbocharger assly and repair/replacement of various parts i.e.Turbo kit,suitable for above DG set;(v) M & L for Removing, transporting to workshop, Repairing & Servicing of self starter of above DG set 50 KVA including replacement of parts such as washer, nut, bolts, bush, solenoid, rotor etc., re-assembling and testing complete all as directed;(w) M&L for taking out Turbo Radiator by disconnecting from DG set for welding,brazing,leak testing and descaling of radiators carried out by Radiwash or other non acidic base solution & refixing the same to its original position and testing on load complete all as directed by Engr-in-charge.

Vijay Construction Co

Sukhi Electricals

NILESH SUBHASH KARALE

GEE CEE ENTERPRISES

M/s. Shree Shakti Enterprise

excel electric co