PROVN OF TOILETS AT CERTAIN LOCATIONS IN TECH AREA AND DOMESTIC AREA AT AF STN AWANTIPUR AND PROVN OF STABILIZER AND AMF PANEL FOR DG SETS AT CERTAIN LOCATIONS AT 8FBSU

B/R PORTION

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 cm, deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and getting out in soft/loose soil, complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate), as in sub floors, sub bases, etc complete all as specified & directed.

M&L for brick work with sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete.

Brick work with old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25cm thick, complete all as specified and as directed.

Removing of excavated material (soil) to a distance not exceeding 50 metres and depositing where directed at a level not exceeding 1.5metre high from the starting point, complete all as specified and as directed.

S&F Roof trusses (framed), trussed, posts, struts, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, base plate and gusset plates etc confirming to Fe 410 -W (Gde-E- 250) quality-A complete all as specified and directed.

S&F galvanised corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roof, 0.63mm thick, grade-O quality, with 120 grms/sqm zinc coating and grade 'B' Class 8 complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised plain mild steel sheeting 0.63mm thickness fixed with l or J type or cranked hook boltes with washers, in roofs as in ridge etc all as specified and directed.

S&F 1.00 mm thick Plain, galvanised, mild steel sheeting, in eave board & straight flashings (length & girth as fixed) with welded and shouldered joint to be provided all as specified and directed by Engr in charge.

M&L preparation of new surfaces of steel or iron work or CGI/PGI sheeting in walls or roofing over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint in camouflaging (Disruptive) pattern (Green, Grey & Brown colour) complete all as specified and directed. (Make: Berger/Johnson/Nerolac/Asian/Shalimar)

M&L for rendering 10 mm thick on fair faces of concrete/brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 on wall surfaces, finishing the surface even and smooth without using extra Cement complete all as specified.

M&L preparing of new or un-plastered surfaces of wall and applying three coats of white washing including preparation of surfaces by filling cracks/holes with white putty, complete all as specified and directed.

M&L preparing new plastered or un-plastered surfaces of walls and applying two coats of Acrylic exterior emulsion paint in camouflaging (Disruptive) pattern in three colours (Green, grey and brown) over a coat of acrylic primer, complete all as specified and directed. Make : Asian/ Berger/ Nerolac/ ICI/ Shalimar/ Johnson

M&L 2nd class soft wood in scantling of clean sawn timber framed and fixed in frame work for ceiling .

S&F 6mm thick of plywood, grade BWP, type BB fixed with screw to mild steel frame work and No of ply 5 as in ceiling all as specified and directed by Engineer-in-Charge.

Preparation of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and providing two coat of synthetic enamel paint over one coat of pink primer all as specified & directed.

M & L Hardcore using broken stone boulders not exceeding 63mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified & directed.

M&L 25mm PCC 1:2:4 Type B-0 (Using 12:5mm stone agg) as in sub base floor , complete all as directed and specified .

M&L coloured/printed non skid ceramic tiles 7 mm thick (square/rectangular) area of each tile exc 0.11 but not exc 0.16 sqm laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement, complete all specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of 450x300x7mm / 350x 250x 7 mm / 450X 350X 7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M & L 75 mm thick PCC (1:3:6) type C-2 using 40mm graded aggregate as in plinth protection even and smooth without using extra cement complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube supply and fixing as specification and drawing.

S&F of factory Made Solid panel PVC door shutter, 28 to 30mm thick (stiles) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded and wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading plain colour PVC sheets for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification & drawing.

S&F 100 mm long stainless steel butt hinges medium weight with stainless steel screw complete.

S&F extruded aluminum alloy handles of size 150mm fabricated type anodised complete.

S&F Aluminium alloy anodised barrel tower bolts of extruded section 150 mm long and fixed complete.

S&F Factory made Steel windows or ventilators side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete, with glazing bars, dovetailed or welded type of 'Z' Section comprising double frame for gauged and glazed Skelton shutter jointed internally with flat iron 40x4 mm complete all as specified and directed by Engr-in-Charge.

3mm thick sheet glass, figured glass, pin head type and glazing with oil putty or fixed with bead/glazing pins in squares size n.exc 0.5 sqm in each pane including hacking out old broken glass (any thickness, size quality or description) all as specified and directed.

S&F of galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

M&L RCC (nominal mix) as in slabs supported on walls, beams, cantilevers, bressummers, lintels over 1.5 m span using type B1 1:2:4 (20 mm graded aggregate) complete all specified and directed.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all specified and directed.

Formwork to sides and soffits of floor or slab, roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc

S&F in PVC flushing cistern 10 ltr capacity white with all internal fittings including brackets PVC connection 45cm long including nut and PVC washer at both ends including 32mm bore PVC long bend flush pipe 90cm long complete all as specified and directed.

S&F in Vitreous China wash down water closet (pedestal pattern), White/coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, complete all as specified and directed.

S&F Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc and making good to floors to match existing, in repair, complete all as specified and directed.

S & F Vitreous china wash hand basin coloured, flat back type of size 550mm x 400mm including waste pipe & plug, porcelain stopper, 32mm dia PVC waste pipe with CP brass coupling and set of bracket complete all as specified and directed.

S&F Vitreous China urinals of minimum size 580x380x350 mm, crystal white, HALF STALL URINAL, with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement with brackets, flush pipe, trap, grating and Union for discharge pipe. (Including fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F CP health faucet of 1.25Mtr long CP flexible tube with necessary fittings complete all as specified and directed.

S & F Stainless Steel Wall Mount Case with Soap Holder & Bruch Holder fixed to wall all as specified and directed by Engr-in-Charge .

S&F toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws

S&F 15 mm bore CP PILLAR tap cast copper alloy with capstan heads screwed down for high press with or without lattered hot or cold with long screwed shank and flynuts screwed for iron pipe complete as specified

S&F 15 mm dia medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F 20 mm dia medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.

Cutting chases, pinning for concealed water tubing and making good to facing where required and pointing in cement mortar 1:3 ,cutting exc 10cm but n.exc 20cm girth all as specified and as directed.

M & L for Lagging to 20 mm dia pipes used in internal water supply or plumbing all round with, 40 min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum all as specified and directed.

S&F 20mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges with chromium plated bracket and fixed all as directed.

S&F 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical double layered with closed top) duly provided with necessary fittings/ fixtures for connecting inlet, outlet, washout and overflow pipes; hoisted and fixed in position complete all as specified and directed.

S&F Ball valves 20 mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 15mm dia 450mm long PVC connection with brass nut and washer complete all as specified and directed.

S&F 15 mm bore CP Bib tap cast copper alloy fancy type crutch or butterfly handles screwed down for iron or for brass ferrule complete.

S&F stop valve/angle valve, fancy type, chromium plated, cast copper alloy screwed down, high pressure, with crutch or butterfly handle of 15mm dia. Screwed both ends for iron pipe or for unions and fixed. all as specified & directed.

S & F two way Angle valve 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions.

S&F PVC (SWR) pipes single socketed,110mm bore, in any length with rubber ring joints fixed to wall and floor, complete all as specified and directed.

S&F PVC (SWR) pipes single socketed,75mm bore, in any length with rubber ring joints fixed to wall and floor, complete all as specified and directed.

PVC (SWR) 75mm bore (dia), Bends, any radius with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

PVC (SWR) 110mm bore (dia), Bends, any radius with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

PVC (SWR) 75mm Bore (dia), Branch Piece, Single (Single Y) Equal or Unequal with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

PVC (SWR) 110mm Bore (dia), Branch Piece, Single (Single Y) Equal or Unequal with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

PVC (SWR) 75mm Bore (dia), junction Single (Single T) Equal or Unequal with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as specified and directed.

PVC (SWR) 110mm Bore (dia), junction Single (Single T) Equal or Unequal with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as specified and directed.

S & F PVC (SWR) vent cowl, size of bore 75mm

S&F CP grating round suitable for 110 mm dia and connecting up, fixed in repairs.

M&L PVC (SWR) floor trap 110 mm dia including jointing with solvent cement complete.

M&L PVC (SWR) Gully trap 125/110 mm setting and jointing with solvent cement complete.

M & L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with glossy finish colour shade complete all as specified and directed by Engr-in-Charge. (Sand will be measured & paid separately)

Supply only Fine aggregate (sand) for sand cushioning

M&L for stone kerb of roughly squared stones of size 20cm x 30 cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surface jointed in cement mortar 1:6 and struck flush kerb stone of any description and laid in any position including two coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

E/M PORTION

Supply, laying and testing cable XPLE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm,4 core.

M&L for sand cushioning to under ground cable provided with a layer of sand 8 cm depth before laying of cable and 15 cm depth after laying and stretching the cable all as specified. Note: Punned thickness of sand shall be measured & paid.

M&L for well burnt sub class 'B' bricks of nominal size 230X115X75 mm abutting each other for mechanical protection of cable with width equal to length of brick complete all as specified.

M&L for point wiring with two single core PVC insulated, unsheathed, FRLS type, 1100 volts grade, multistranded copper conductor cable 1.5 sqmm in and including PVC casing caping ISI marked with all connected accessories including one single core multistanded PVC insulated, unsheathed, FRLS type, 1100 volts grade,1.5 sqmm copper conductor cable unsheathed as earth continuity cable including concealed pressed steel GI terminal boxes of suitable way with 3 mm thick laminated sheet cover for mounting of switches, socket, fan regulators, connected to common earth dolly complete all as specified for the following:- (a) One light /fan/ point controlled by one nos, one way 5/6 Amps switch.

(b) All as per srl item No 79.00 here-in-before but using One 3/5 pin socket outlet, 5/6 Amp, independent controlled by one nos, one way switch.

All as per srl item No 79.00 here-in-before but using cable of size 2.5 sqmm (for phase & neutral) and 2.5 sqmm as continuous earth cable for 15/16 Amps socket outlet, independent controlled by one nos, one way switch complete all as specified.

S&F of piano type socket outlet flush type, 3 pin 2-in-1, 5/6 Amps, 230 volts AC, 50 Hz, multipurpose type complete all as specified.

S&F of piano type switch socket combination flush type, 2-in-1 3 pin, 6/16 Amps, 230 volts AC, 50 Hz, multipurpose type complete all as specified.

S&F of piano type switch one way, SP, flush type, 5/6 Amps, 230 volts AC, 50 Hz complete all as specified.

S&F of ceiling rose 3 terminals, PVC/polycarbonate/bakelite, isolated body 230 volts AC, 50 Hz complete all as specified.

S&F in replacement of sheet metal enclosure DB SPN 8 way, double door, 240 volts AC, recess mounting complete with suitable busbar, neutral link & earth link suitable for MCB DP/SPN as incomer & MCB SP as outgoing complete all as specified.

S&F of MCBs, SP, 6-32 Amps, 230 volts,10 kA rupturing capacity, C curve type complete all as specified.

S&F of MCBs, SPN, 32-63 Amps, 230 volts, 10 kA rupturing capacity, C curve type complete all as specified.

S&F of LED tube light fitting, box type 230 volts AC suitable for & including 9/10 watts LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified. Make- Havells/Phillips/Wipro

S&F in LED tube light fitting 1x20/ 22 watts, 220 volts AC, 1200 mm, with aluminium housing & integrated electronic driver complete with driver with polycarbonate diffuser & thd< 10% including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose complete all as specified. Make- Havells/Phillips/Wipro

M&L for fixing of exhaust fan 230 mm sweep 220 V, single phase 50 Hz metal body four nos of blade, double ball bearing along with louvers & bird repellers including cutting chases and making good disturbed surfaces by cement mortar along with fixing with help of hole fastener. Complete all as specified and as directed.

S&F of LED bulk head light fittings weather proof, anti corrosion wall/ceiling mounted opel colour decorative, round shape/ oval shaped with PC cover suitable for & including 10 watts LED lamp, lamp holders complete with all accessories all as specified.

S&F gun metal globe valve with iron handle screwed both ends for iron pipe and fixed of size 20 mm bore :- Make- Zoloto, Audcu, L&T

S&F gun metal globe valve (in replacement) with iron handle screwed both ends for iron pipe and fixed of size 15 mm bore :- Make- Zoloto, Audcu, L&T

Supply and laying of galvanised steel water tubing medium grade trenches / wall /floor with all fittings , connections as required at site of size 25 mm bore :- Make : Tata/Jindal