PROVN OF GEN SHED IN UNIT AREA AND PROVN OF TWO OFFRS BATHROOMS NEAR BLDG NO T-59 AT RUDRAPRAYAG UNDER GE 871 EWS

Amount

SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS.

Excavation in trenches, not exceeding 1.50mtr wide and not exceeding 1.50mtr in depth; for foundation, etc. or for laying cable, pipe lines, not exceeding 10 Sqm on plan and not exceeding 1.50 mtr in depth and getting out, in any type of soil, complete all as specified and as directed.

Excavation over areas, not exceeding 1.50mtr in deep; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. exceeding 10 Sqm on plan and getting out, in any type of soil, complete all as specified and as directed.

Plain cement concrete M-7.50(1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm, any type of soil, complete all as specified and as directed.

Removing excavated soil not exceeding 50mtr and depositing where directed at a level not exceeding 1.50 mtr above the starting point, complete all as specified and as directed.

Formwork for rough finished surfaces of concrete for flat surfaces of foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and as directed.

Formwork for rough finished surfaces of concrete to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc, complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Reinforced cement concrete (nominal mix), M-20(1:1.5:3), type B-0, (using 12.50mm graded crushed stone aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

Brickwork with fly ash modular bricks, straight or curved on plan exceeding 6.0 mtr mean radius built in cement mortar 1:4, complete all as specified and as directed.

Brickwork with fly ash modular bricks, straight or curved on plan exceeding 6.0 mtr mean radius built in cement mortar 1:6, complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Plain cement concrete M-20(1:1.5:3), type B-1, (using 20mm graded crushed stone aggregate), nominal mix as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, copings and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in two layers, first layer of 10mm thick and second layer of 5mm thick in cement mortar 1:4, including mixing with liquid water proofing admixture @ 200ml per Kg of cement, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed. Note: Cost of water proofing admixture shall be deemed included in quoted rates.

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of cement paint over one coat of priming plastered and other surfaces with alkali resistant priming paint, complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white washing, complete all as specified and as directed.

Damp proof course in plain cement concrete M-15(1:2:4), type B-0 (using 12.50mm graded crushed stone aggregate), nominal mix, 40mm thick, to horizontal or vertical surfaces including necessary formwork, complete all as specified and as directed.

Hardcore of broken stone or boulders gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and as directed.

Plain cement concrete M-7.50(1:4:8), type D-2 (using 40mm graded crushed stone aggregate), 100mm thick, as in sub base, finish even and smooth without using extra cement, complete all as specified and as directed.

Non-skid, coloured, ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Per Square Metre but not exceeding 0.18 Per Square Metre, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed.

Glazed ceramic coloored tiles in vertical surface/ dado, size 300x200x6/7mm, 300x450x6/7mm, 350x250x6/7mm, or 450x350x6/7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including rendering of 10mm thick in cement mortar 1:4 as backing of tiles, complete all as specified and as directed.

Plain cement concrete M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate), 75mm thick, as in plinth protection, finish even and smooth without using extra cement, complete all as specified and as directed.

Figured glass, 3.0mm thick, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane, complete all as specified and as directed.

Factory made steel ventilator, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter, jointed internally with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and and as directed.

Plain cement concrete, M-7.50(1:4:8), type C-D (using 40mm graded crushed stone aggregates), as in bed to drain pipes of 150mm bore, including packing under and completely surrounding pipes with concrete after laying of pipe and tested; complete all as specified and as directed.

Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing in SSR, complete all as specified and as directed.

Butt hinges, size 75mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed.

Extruded aluminium alloy handles, fabricated type, anodised, size 125mm, complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 125mm long and fixed, complete all as specified and as directed.

Soap dish, stainless steel, fancy type, fixed to plugs with chromium plated brass screws, fixing in repairs, complete all as specified and as directed.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges, brass chromium plated, fancy type, including end brackets, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Western style EWC, all-in-one, white colour with soft close seat cover including cistern, floor mounted, complete all as per price list/ catalogue of following makes: Make: Cat Part No- 20122 (S-22)/ 20127(P-18) (Aspire) of Hindware or equivalent in Jaquar/ Parryware.

Toilet paper holder, stainless steel chromium plated, without cover, wall mounted, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F450027 of Hindware or equivalent in Jaquar/ Parryware.

Health faucet with 1.20 mtrs stainless steel flexible tube including wall hook for wall mounting, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F160193 of Hindware or equivalent in Jaquar/ Parryware.

Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern, complete all as specified and as directed.

PVC (SWR) floor trap, 75mm diameter of outlet, plain with grating including jointing with adhesive, complete all as specified and as directed.

Unplasticised PVC pipes of 15mm bore and pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and as directed.

Unplasticised PVC pipes of 20mm bore and pressure rating 15 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and as directed.

Unplasticised PVC pipes of 25mm bore and pressure rating 20 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and as directed.

Wall mixer 3-in-1 with L-bend pipe including overhead shower and hand shower, made of stainless steel or chromium plated metals, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F690022 of Hindware or equivalent in Jaquar/ Parryware.

Single lever basin mixer without popup waste, made of stainless steel or chromium plated metals, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F400009 of Hindware or equivalent in Jaquar/ Parryware.

Main mirror vanity cabinet, with basin Bib taps, 2-in-1, stainless, complete all as per price list/ catalogue of following makes: Make: Cat Part No- C896F7C, C896D7C and C896E1C of Parryware or equivalent in Jaquar/ Hindware.

Bib taps, 2-in-1, stainless, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F340005GCP of Hindware or equivalent in Jaquar/ Parryware.

Glass shelf, fixing with rust free screws and PVS plugs in walls, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F880010 of Hindware or equivalent in Jaquar/ Parryware.

Ultra-thin stainless rain shower with 225mm shower arm, single flow, complete all as per price list/ catalogue of following makes: Make: Cat Part No- F160142 and 160143 of Hindware or equivalent in Jaquar/ Parryware.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and as directed.

Granite (of any type) work (table rubbed and polished), 20mm thick, as in steps, jambs, pillars, window cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, and including laid over screed bed or bedding layer 20mm thick in cement mortar 1:6, complete all as specified and as directed.

PVC (SWR) pipes, 110mm bore, single socketed, capacity not, less then 4.50 Kgf/Sqcm, in any length fixing with adhesive/ solvent cement, laid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) bends of 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, laid in trenches, complete all as specified and as directed.

PVC (SWR) bends of 75mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed.

PVC connections 15mm size with brass nuts, of length 600mm, fixing in repairs, complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) with lid, hoisted and fixed in position all as specified in SSR Part-I including ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed.

Salt-glazed stoneware gully traps, size 150mmx100mm, square round mouthed, type 'P', complete all as specified and as directed.

Anodised aluminium snap grid frame work for false ceiling, powder coated, comprising of aluminium Tee (weight of section not less than 280 gms/mtr) and aluminium angle (weight of section not less than 280 gms/mtr), grid size 605x605mm, including Hangers 6.0mm dia, galvanised iron (upto1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3 mm size 60mm long and expansion hold fasteners 12.50mm dia, 40mm long, complete all as specified and as directed.

Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions, complete all as specified and as directed by Engineer-In-Charge.

PVC (SWR) pipes, 110mm bore, single socketed, capacity not, less then 4.50 Kgf/Sqcm, in any length fixing with adhesive/ solvent cement, fixed on walls with mild steel flat iron clamp 25x3mm and nails of required size/ length, complete all as specified and as directed.

PVC (SWR) vent cowl of 110mm bore pipe, complete all as specified and as directed.

Excavation in post holes (or similar holes) each not exceeding 0.50 Cum, getting out in any type of soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 Cm, complete all as specified and as directed.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde E-250) quality B, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation, complete all as specified and as directed.

Rolled mild steel in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc, conforming to Fe-410 W (Gde E-250) quality-A, complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with two Nos. of washers and one hexagonal or square nut, length of bolt exceeding 5cm but not exceeding 10cm long and diameter of neck in 11mm to 15mm, complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with two Nos. of washers and one hexagonal or square nut, length of bolt exceeding 22.50cm but not exceeding 30.0cm long and diameter of neck in 16mm to 20mm, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-1, (using 20mm graded crushed stone aggregate), nominal mix as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, copings and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Formwork for rough finished flat surfaces of concrete to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and as directed.

Formwork for rough finished surfaces to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide, complete all as specified and as directed.

Providing precast reinforcement cement concrete M-15 (1:2:4), type-B1 (using 20mm graded crushed stone aggregates), as in landings, cover slabs (for man holes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar 1:6, complete all as specified and as directed.

Surface excavation not exceeding (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and as directed.

Chequered cement concrete coloured tiles, pre-polished, size 300mmx300mmx20/25mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over 20mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed.

Rolled mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S-1161: 1979 grade St.-240, complete all as specified and as directed.

Rolled mild steel in as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410 W (Gde E-250) quality-A, complete all as specified and as directed.

Rolled mild steel in, plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290, (Gde E-165), complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-2 (using 40mm graded crushed stone aggregate), 100mm thick, as in sub base, finish even and smooth without using extra cement, complete all as specified and as directed.

SCHEDULE 'A' PART-II : BOQ OF WORKS FOR E/M WORKS.

Point wiring (in new concealed/ exposed conduits to surfaces as required at site) for 3-pin, 15/ 16 Amps, switch socket combination on independent board with 4.0 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, FRLS, 1100 Volts, using colour coding, drawn in and including any type of conduit/ new casing and caping, any size/ dia including all accessories concealed by chasing/ cutting or fixed with PVC plug and mild steel screws on the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheathed 4.0 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed.

Point wiring (in new concealed/ exposed conduits to surfaces as required at site) for one light/ fan/ bell point controlled by one switch with 1.50 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, FRLS, 1100 Volts, using colour coding, drawn in and including any type of conduit/ new casing and caping, any size/ dia including all accessories concealed by chasing/ cutting or fixed with PVC plug and mild steel screws on the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheathed 1.50 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed.

Description all as serial item No- 2.02 here-in-before but for one 3- pin, 5/ 6-Amps, socket outlet on same board.

Description all as per serial item No- 2.02 here-in-before but for one 3-pin socket outlet 5/6 -Amps on the independent board.

Switch piano, flush type, single pole, one way, 5/ 6 Amps, complete all as specified and as directed.

Switch piano, flush type, single pole, one way, 15/ 16 Amps, complete all as specified and as directed.

Socket outlet, 2-in-1, 3-pin, 5/ 6-Amps, flush type, complete all as specified and as directed.

Socket outlet, 2-in-1, 3-pin, 5/ 6 and 15/ 16 Amps, combined, flush type, complete all as specified and as directed.

Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, size 65mmx25mm dia, complete all as specified and as directed.

LED light fitting mirror type with high out put diffuser 2-feet, 10 watt 220 Volt, AC, decorative type with driver holder including and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, fixing in repairs, complete all as specified and as directed. Make: Havells ordering code- LUMILINE+BS10WLED865SPCSS or equivalent in Philips/ Bajaj/ Crompton.

LED lights fitting wall surface mounted, 18 Watt, 220 Volt, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, fixing in repairs, complete all as specified and as directed. Make: Havells cat part No- LUMILINEPLUSNEOBS18WLED830SPCSSIND or equivalent in Philips/ Bajaj/ Crompton.

Sheet metal enclosures for Single Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-65, 8-way with 200 amps rated busbar, 240 volts, as per IS-8623, fixing in repairs, complete all as specified and as directed.

Sheet metal enclosures for Triple Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-65, 4-way with 200 amps rated busbar, 240 volts, as per IS-8623, complete all as specified and as directed.

MCB, single pole, 6 to 32 Amps, 240 Volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

Sub main wiring (concealed conduits to surfaces) for circuits/ submain wiring alongwith earth wire with two run of 4.0 Sqmm of fire resistance, PVC insulated copper conductor, single core cable, multi-stranded, FRLS, ISI marked, 1100 Volts grade and one run of 4.0 Sqmm, FRLS, PVC insulated copper conductor, single core cable, multi stranded, ISI marked, 1100 Volts grade as earth wire connected to earth terminal, drawn in and including non metallic medium grade rigid PVC conduit, fire resistance, ISI marked, 25mm dia including all accessories concealed by chasing/ cutting grooves in the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, complete all as specified and as directed by Engineer-In-Charge.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area 10.0 Sqmm, 2.0-core, laid in trenches or passing through pipes, including suitable lugs and accessories for making connections at both ends, complete all as specified and as directed.

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanised iron wire, size 4.0mm dia as earth lead, by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 20mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

Water heater storage type (geyser), wall hanging, storage type steel body with heavey duty inner tank and heating element upto 2 KW capacity 25 litre, BEE 5-Star rated, single-phase, 50 Hz AC, energy saving high density PUF insulation, complete with all accessories such as safety valve, thermostate, NRV, etc, complete all as specified. Make: Havells cat part No- GHWAPPTWB025 or as equivalent in Bajaj/ Jaquar/ Crompton.

Exhaust fan, steel body with copper winding motor, AC single Phase, 230 Volt, of size 300mm sweep with, blades, and frame and louvers, complete all as specified and directed. Make: Havells ordering code- FHVVEMTDBS12 and model- Ventil Air DS Green or equivalent in Philips/ Bajaj/ Crompton.

MCB, double pole, 40 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

M/S RAMESH LAL (BID ID -3225260)

Ganesh Dimri Construction (BID ID -3225279)

M/S BHAWANI CONSTRUCTION (BID ID -3225303)

NOORI ELECTRIC ENGINEERING WORKS (BID ID -3224268)

Ram Naresh Singh Sikarwar (BID ID -3225182)