Providing and Erecting Street Light on Bela Bharatnagar CC Road Morbi, Taluka Morbi, Dist- Morbi.

Name of Work:- Providing and Erecting Street Light on Bela Bharatnagar CC Road Morbi, Taluka Morbi, Dist- Morbi.

Sr. Quantities Estimated Rate

No. estimated but

may be more or Description of Item.

In Figures In Words according

1 370 Mtr Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI 46.46 Rupees Forty Six

And Paise Forty

marked copper wires of following size to be erected as directed. Six Only

(e) 1.50 Sq.mm 3 core round PVC sheathed

2 20 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 56.56 Rupees Fifty Six

And Paise Fifty Six

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 Only

erected in existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and

bolts if required.

(e) One wire 6.00 sq. mm

3 4 Mtr providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, 91.91 Rupees Ninety

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 Ninety One Only

erected in existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and

bolts if required.

(f) One wire 10.00 sq. mm

4 44 Ea Supplying and erecting LED street light / Flood light fittings with High power White LEDs 4997.48 Rupees Four

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w Hundred Ninety

and corrosion free High pressure die cast aluminum housing with smooth finish powder Seven And Paise

Forty Eight Only

coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any wattage capacity between the ranges

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line

supply with over-voltage protection.

(ii) above 48 to 60 Watts Cat-lll

5 8 Ea Supplying and erecting LED street light / Flood light fittings with High power White LEDs 10818.11 Rupees Ten

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w Hundred Eighteen

and corrosion free High pressure die cast aluminum housing with smooth finish powder And Paise Eleven

coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any wattage capacity between the ranges

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line

supply with over-voltage protection.

(vii) above 200 to 250 watts Cat-lll

6 1 Ea Providing and erecting Approved make Four pole moulded case circuit breaker having 6173.12 Rupees Six

breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. Hundred Seventy

with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all Three And Paise

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III

7 1 Ea Providing and erecting Approved make Four pole moulded case circuit breaker having 6790.23 Rupees Six

breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. Hundred Ninety

with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all And Paise Twenty

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III

(10% Added For Enclosure)

8 1 Ea Providing and erecting Approved make Earth fault Relay suitable to mount with inter 4687.41 Rupees Four

connection suitable to following size of moulded case circuit breaker having CT ratio & Hundred Eighty

MCCB rating as following along with shunt trip 220V AC. with all internal connections & Seven And Paise

complete erected in existing M.S.housing..

9 0.5 RMT Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars 1961.42 Rupees One

with four equal Nos. of electrolyte bus having current density not more than 1.6 Amp. / Hundred Sixty

sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for One And Paise

phase sequence of following current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in existing cubical panel with

necessary connections.

(A) Suitable for 100 Amp. Capacity

10 44 Ea Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having 270.68 Rupees Two

Hundred Seventy

breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI And Paise Sixty

Mark Eight Only

11 5 Ea Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 638.32 Rupees Six

10KA breaking capacity & confirms to IS :8828 in existing box having following capacity Eight And Paise

(b)40 Amp. Cat.III Thirty Two Only

12 60 Kg Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 77.77 Rupees Seventy

Seven And Paise

13 30 Ea Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe 823.15 Rupees Eight

with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 Three And Paise

SWG erected & connected as directed (For panel) Fifteen Only

14 30 Ea For using salt and charcoal / coke as required for pipe type earthing. 171.70 Rupees One

Hundred Seventy

15 2 Ea Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing 4591.46 Rupees Four

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free Hundred Ninety

hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, One And Paise

Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of

12mm with constant ohmic value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications with chamber and heavy duty

cover. (A)(approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer Incharge has to

ensure the value of earthing resistane mentioned in test Certificate) & having back filling

compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing

as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

16 1350 Mtr Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid 140.39 Rupees One

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing And Paise Thirty

trench / pipe of following size of cables Nine Only

(C) 4 core 10 Sq. mm

17 65 Mtr Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium 153.52 Rupees One

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe Three And Paise

of following size of cables Fifty Two Only

(A) 4 core 16 Sq. mm

18 1360 Mtr Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for 74.74 Rupees Seventy

laying any size of cable or locating the fault all over the run and back filling the same and Seventy Four Only

making the surface as normal ground.

19 20 Mtr Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for 357.54 Rupees Three

laying any size of cable or locating the fault all over the run and back filling the same and Seven And Paise

making the surface as normal ground. Fifty Four Only

(B) If additional machinery like hammer driller or JCB use [Add]

20 10 Mtr Drilling the road without breaking the road surface (Asphalt) for laying of cable for feeding 492.88 Rupees Four

power supply by making up to following size of holes at both ends complete. Two And Paise

(A) Up to 100 mm bore dia Eighty Eight Only

21 10 Mtr Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground across the 226.24 Rupees Two

road crossing or on floor with necessary material in an approved manner and making the Six And Paise

ground as per original. Twenty Four Only

(F) 100 mm dia.

22 1300 Mtr Providing & laying approved make Double walled corrugated pipes (DWC) of 62.62 Rupees Sixty Two

And Paise Sixty

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same Two Only

material at required depth in existing trench for laying of cable. below ground / road

surface for enclosing cable

(A)50 mm outer dia

23 3 Ea Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC 38.38 Rupees Thirty

Eight And Paise

insulated armoured cable complete with out going tails, insulating tape etc for following size Thirty Eight Only

(C) 2 to 4 core 10 Sq. mm

24 2 Ea Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC 47.47 Rupees Forty

Seven And Paise

insulated armoured cable complete with out going tails, insulating tape etc for following size Forty Seven Only

(D) 2 to 4 core 16 Sq. mm

25 8 Ea Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following 15.15 Rupees Fifteen

And Paise Fifteen

size evenly crimped with high pressure tool & connected to switchgear terminals with Only

brass/cadmium plated nut bolts in an approved manner.

26 36 Ea Replacing old and U/s By Supply of approved make FRP Pole having following specifications: FRP Light Pole made by 14059.20 Rupees Fourteen

CNC filament winding machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The Thousand Fifty

pole should be in one piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well Nine And Paise

as non conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Twenty Only

Material duly painted with Epoxy paint.

Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper adhesion of the

paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more than 10% of the

length of pole for the given load“ Pole should be generally made as per the dimensional data, performance criteria and some

interchangeability features of poles as per standard ANSI C 136.20 latest version or ASTM D 4923/01 including cable

termination box with necessary accessories . The size of pole and type of installation with foundation as per manufacturer

details and site requirement are as below .

(1) Suitable for base plate mounting single arm Bracket.

[H] Overall length of 6 Mtr. Average Thickness: 7.5mm

Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx. Weight of Pole 32 kg approx. (Without Base) Anchor Base (Size

27 4 Ea. Supply of approved make FRP Pole having following specifications: FRP Light Pole made by CNC filament winding 14894.47 Rupees Fourteen

machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one Thousand Eight

piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non conductive & Hundred Ninety

shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly painted with Four And Paise

Forty Seven Only

Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper adhesion of the

paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more than 10% of the

length of pole for the given load“ Pole should be generally made as per the dimensional data, performance criteria and some

interchangeability features of poles as per standard ANSI C 136.20 latest version or ASTM D 4923/01 including cable

termination box with necessary accessories . The size of pole and type of installation with foundation as per manufacturer

details and site requirement are as below .

(2) Suitable for base plate mounting Double arm Bracket.

[C] Overall length of 6 Mtr. Average Thickness: 8mm.

Top/ Bottom OD Dia A/F 114/174 mm ± 2mm approx. approx. Weight of Pole 38 kg approx. (Without Base) Anchor Base

(Size 300X300 & 18mm th.)

28 36 Ea Providing Aluminium arm bracket of having 2 sets of suitable SS304 hardware for fixing the brackets & spread of 1.2 Mtr 2234.12 Rupees Two

(Suitable for 89 to 114 mm pole top dia) Thousand Two

(A) Single arm bracket Hundred Thirty

29 4 Ea Providing Aluminium arm bracket of having 2 sets of suitable SS304 hardware for fixing the brackets & spread of 1.2 Mtr 3450.16 Rupees Three

(Suitable for 89 to 114 mm pole top dia) Thousand Four

(B) Double arm bracket And Paise Sixteen

30 1 Ea Supplying & erecting IP 55 grade following size section pillar fabricated from joint less 16691.26 Rupees Sixteen

M.S. Sheet with angle iron legs made from jointless M.S. Angle with cable clamps to be Hundred Ninety

buried in ground to have appropriate erection to work uniform until erected with cement One And Paise

Twenty Six Only

concrete foundation and 45 cm high bricks work finishing with plaster etc. hinged double

door internally supported on both side,

with internal and outside looking arrangement with look and keys in duplicate 35 x 35 x

mm M.S. Angle of Two Nos. one is welded and other with nut and bolt for erecting Bakelite

sheet. Painting the Section Pillar inside and out side with three tank powder coated paint.

section pillar roof should be without joint with water leakage proof & tested as per IP 55 test

& followed by IS 2147 of

(A) 150 X 90 X 75 cm section pillar fabricated from 14 Gauge MS Sheet with angle iron

legs 95 cm long made from 40 X 40 X 6 mm thick MS angle.

31 1 sq.mt Supplying and erecting HYLAM sheet on existing angle iron frame.for following thickness 1927.08 Rupees One

r (E) 10mm Hundred Twenty

Seven And Paise

32 3 Ea Supplying & erecting approved make Digital time switch having lithium cell 6 years 3168.37 Rupees Three

operative and operate battery backup 1 channel day clock with 14 memory programme, Hundred Sixty

suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup Eight And Paise

Thirty Seven Only

time 1 minimum & LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure & transparent cover

erected as required with necessary connection erected as directed.

33 3 Ea Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per 2782.55 Rupees Two

direction Cat III Hundred Eighty

(D) 4 pole 440V 40 Amp. Two And Paise

Fifty Five Only

34 1 Ea Supplying, erecting, testing, commissioning approved make M.S. Polygonal High Mast Pole having 173088.75 Rupees One

Lakh(s) Seventy

following general Specification.

(a) Polygonal Section fabricated from M.S. Plate confirms BSEN 10025 & Hot deep galvanized minimum Eighty Eight And

65/86 micron (as per IS 2629 /1985) Lantern carriage with ring and rubber lines for erection of luminaries Paise Seventy Five

of suitable site. Only

(b) Maximum telescopic section not more than four

(c) Double drum gear pipe motorized winch with 6mm dia S.S. Rod (For 16 mtr and above size)

(d) Approved make L.E.D. aviation light = 1 No. Lightening arrestor = 1 No. with necessary wiring of

sq.mm 5 core ISI copper cable Unarmoured.

(e) Bottom most section suitable for mounting reversible motor and switchgears having door not more than

1400mm x 300mm with waterproof gasket & hinges & locking arrangement.

(f) Pole structure comprises suitable size of reversible motor, cable and necessary switchgears with control

(g) bottom section shall have suitable size of thickness supports ribs foundation bolts nuts etc.

(h) Item not comprises the cost of lanterns.

(i) Necessary Cement Concrete foundation as per IS including testing & commissioning of the entire

structure for following size of High Mast poles

[3] High Mast 16 Mtr. TOP A/F 150 mm, BOTTOM A/F 450 mm, No. of Sec. No. - 2, Bottom Thickness -

4 mm, Top Sec. 3 mm, Size of Base Plate - dia.560 mm x 20 mm thick, Foundation Bolt Size M24 x

mm, Qty - 8 Nos., Suitable for mounting Fitting of Light - 8 Nos.

In Words : Rupees Sixteen Lakh(s) Sixty Nine Thousand Two Hundred Seventy Nine And Paise Fifty Two Only

I/We am/are willing to carry out the work at ____________% above/below (in Figures)__________________________ percent Above / below (in words) the estimated rates mentioned

above amount of my\our tender works out as under :-

Estimated amount put to Tender Rs._________________

Deduct _____% below Rs._________________

(-)Less For Dismantle Material Rs._________________

Net Amount Rs._________________

Estimated amount put to Tender Rs. _________________

(-)Less For Dismantle Material Rs. _______________

Net Amount Rs. _________________

A I/We hereby declare that I/we have visited the site and fully acquainted my self / our selves with the local situation regarding material,labour and other factors pertaining to the work before

submitting this tender.

B I/We hereby declare that I/we carefully studied the conditions of contract, detailed technical specifications and other tender documents of this work and agree to execute the same

(Signature of the Contractor) Deputy Executive Engineer

Electrical R&B Sub Division

Executive Engineer

Electrical R&B Division

Note 1 Please strike out whichever is not applicable.

2 In the case of tendered amount being quoted incorrectly the quoted pered percentage Below/Above will be considered as final.