REPAIR TO ROOF TREATMENT, PLUMBING WORKS, RWP, WATER SUPPLY FIXING AND FIXTURES, CAMOUFLAGE PAINTING AND MISC WORKS IN OMQ AT AF STN BHUJ

Amount

Taking down existing tarfelt from roof including plaster and remove from site complete all as specified and directed .

M&L, PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in roof kerbs/coping/ bed block / depression complete all as specified and directed.

M&L, 10mm thick rendering in cement mortar 1:3 on faces of brick work or concrete surfaces with WPC, finished even and smooth W/O using extra cement as in roof. (WPC shall be measured & paid seperately) complete all as specified and directed .

Supply only integral water proofing compound. (ISI marked)

M&L, water proofing treatment on roof and preparing the surfaces to receive WPT treatment , applying cold bituminous primer @ 0.30 ltr / Sqm conforming to IS 3384 applied on plastered surfaces including side walls , followed by a layers of APP based polymeric membrane reinforced with polyster non woven fabric (weighing 3.5 Kg/Sqm(minimum) and 3 mm thick) with mineral finish laid on primed surface by torch application with side overlap 100 mm and ends over laps 150 mm , joints sealed properly as per manufacturers instructions all as specified and directed .

M & L cleaning and removing all scale and dirt etc from tanks including refixing to position of water tanks, 500 ltr capacity complete all as specified and directed.

M & L cleaning and removing all scale and dirt etc from tanks including refixing to position of water tanks, 750 ltr capacity complete all as specified and directed.

M & L cleaning and removing all scale and dirt etc from tanks including refixing to position of water tanks, 1000 ltr capacity complete all as specified and directed.

S&F, in repair 20mm bore ball vavle high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Demolition of Precast concrete block walling built in cement mortar

M&L for Precast cement concrete block masonary with solid blocks exc 10cm in width Type C1 (1:3:6) 20mm graded and setting in cement mortar 1:6 all as specified and directed

Taking down Chowkats or frames not exc. 1.5 Sqm each, with shutters (without taking off shutters from the frame).

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises.

S&F PVC door PDS-01 comprising of shutter and frame of Make : Rajshree/Accura Polytech Pvt Ltd (Accucel) all as shown on drg No.CEAA/TD/149 sheet No. 1/1 (PVC RIGID FOAM) , door frame/ chowkats of solid rigid foam profile FP-6030 and shutter of solid PVC foam profile FP 7114 with 4 mm thick high pressure compact laminate as infill (Panel) including necessary hardeware fittings all as specified and directed by EIC.

M&L for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out of JINDAL/ INDAL anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) all as specified and directed.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately. Note : main section of aluminium shall be used 100mmx45MM with same thickness as mentioned in lieu of drg 65mm x 38mm above reffered due to less space available for fixing wire gauge shutter fixing grill

M&L for aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 4.4 mm x 7mm

M&L for 25 mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate in sub base of floors etc.

M&L for glazed digital ceramic coloured tiles Ist quality in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over

M&L for 10mm thick rendering on vertical surface in cement motar 1:4 as backing coat complete.

M&L in repairs for 20mm thick granite, Z black (table rubbed and polished) for platforms, wall lining (veneering to wall), cills and in similar items laid over and including 15mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixutre of pigment to match with shade of granite external edges rounded.

Taking up on down steel tubing and connection incl cleaning for refining of the following bore of pipe

a) 15mm bore of pipe

b) 20mm bore of pipe

c) 25/32mm bore of pipe

S&F CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls and ceilings or laid in floors of following sizes: (SDR-13.5 of Make : Astral or equivalent of Supreme / Finolex)

20mm nominal dia of pipes

25mm nominal dia of pipes

32mm nominal dia of pipes

S&F in repair grating doom 125mm dia with waste hole of PTMT (minimum weight 40 grams)

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm.

Dismantling of cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required all as directed by Engr-in-charge following bore of pipe

100/110mm dia of pipes

75mm dia of pipe

S&F of UPVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors of following size :- (Make : Astral type 'B' pipes or equivalent)

110mm dia of pipe

75mm dia of pipe

S&F of UPVC junction single 'Tee' equal with door opening, ISI marked, IS-14735, jointed with solvent cement of following sizes :- (Make : Astral type 'B' pipes or equivalent)

110mm dia of pipe

75mm dia of pipe

S&F PVC (SWR) bends any radius of following sizes :-

a) 75mm bore

b) 110mm bore

S&F in repairs Hand health Faucet spray to EWC with PVC nozzle, and PVC flexible pipe etc complete.

S&F in repairs bathroom cabinet PVC frame box type with mirror in front of size 350x450mm with 6 m thick glass fixed to wall with screws complete all as specified and directed by Engineer-in-Charge.Make : Prayag(Cat No :551) or equivalent as approved by GE

S&F in repair bib cock with wall flange, cast copper alloy, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm dia of piep. Make : Jaquar, Cat No QQT-7037 or equivalent as approved by GE.

S&F in repairs Angular stop cock with adjustable wall flange, cast coper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, and fixed for bore 15mm bore of pipe. Make : Jaquar, Cat No - QQT-7053 or equivalent as approved by GE.

S&F in repairs chromium plated mixing valve, wall mixer 3 in 1 system with provision for both telephone shower and overhead shower complete with wall flange with 115mm long bend pipe including three joints to steel pipe or unions. Make : Jaquar, Cat No QQT-7281 or equivalent as approved by GE.

S&F in repairs chromium plated mixing valve (central hole basin mixer) with small spout without popup waste system with 450mm long braided hoses including three joints to steel pipe or unions. Make : Jaquar, Cat No - QQT-7167B or equivalent as approved by GE.

S&F in repairs chromium plated shower rose overhead single flow 100mm dia (ABS chrome plated) without Arm including fixed to steel pipes or union and complete all as specified. Make: Jaquar, Cat No - OHS-1989 or equivalent as approved by GE.

S&F in repairs chromium plated telephone shower with 1.5m long flexible tube & swill wall hook including fixed to steel pipes or union and complete all as specified. Make : Jaquar, Cat No - HSH-5537H or equivalent as approved by GE.

S&F in repairs chromium plated metropole flush valve dual flow concealed type woth control cock operation plate 40 mm size including fixed to steel pipes or union and complete all as specified. Make : Jaquar, Cat No - FLV-1089Q or equivalent as approved by GE.

S&F in repairs of vitreous China wash basin including pedastal, white, flat back, size 630mm x 450mm including chromium plated waste coupling, plug and chain, necessary brackets. Make : CERA, Cat No 1008 & 1108 or equivalent in Hindaware as approved by GE.

S&F in repairs chromium plated soap dish holder. Make Jaquar, Cat No AQN-7731 or equivalent as approved by GE.

S&F in repairs chromium plated toilet paper holder. Make Jaquar, Cat No AQN-7751 or equivalent as approved by GE.

S&F in repaires chromium plated towel rail 24" long between flanges. Make Jaquar, Cat No AQN-7711 or equivalent as approved by GE.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern)(wall hung type) white (excluding, flushing cistern and flush pipe) complete connected to drain make : CERA, Cat No - 2033 & 2315 or equivalent as approved by GE

S&F in repair sink with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all sizae 915 x 460 mm, bowl size 410 x 330 x 180 mm mm Make : Nirali (Model : elegance small from regular range, glossy) or size 915 mm x 460 mm bowl size 410 x 330 x 178 mm of make : Jayana (Model : Jujpiter sink with Drain board No: SBSD 5 glossy) or equivalent and nearest size of make : Lorrentto, Neelkanth, Diamond.

Supply and Fixing of Stainless steel 304 Grade Plate Rack made of 1 mm thick stainless steel sheet, overall size 60cm x 90cm for 6 plates as approved by GE. Make: Prayag Cat No P-336 or nearest in Nirali, Neelkant as approved by GE

Taking down cement plaster on walls etc, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces complete all as specified and directed.

M&L for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:6 and finished even and smooth without using extra cement as specified.

M&L for rendering on concrete surfaces 15mm thick in two layers first coat 10mm thick in CM 1:6 and second coat 5mm thick in CM 1:4 with water proofing compound @3% by wt of cement, finished even and fair complete all as specified and directed..

M&L for preparation of new or previously untreated concrete extrernal surfaces and applying two coats of exterior emulsion paint all as specified and directed by EIC .

M&L for preparing new plastered ceiling/soffits of chajjas surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of Acrylic putty by finishing the surfaces even and smooth complete all as specified and directed by EIC.

S/F in repairs 100mm size of hinges butt hinges, medium weight, cold rolled mild stee and fixed all as directed by Engr-in-Charge.

S&F in repairs 20/22mm dia fancy type SS 304 grade curtain rods with wall thickness not less than 1.25mm, fixed to walls with and including a pair of fancy type SS brackets and SS clamps best quality as approved by GE complete all as specified and as directed. (Note - Length of curtain rod shall be measured and paid for as one unit. Quoted rate is deemed to include for provision of a pair of brackets and clamps per unit length)

S&F in repairs 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screw to timber frame works including teak wood beading 20mm thick alround and beading painted with 2 coats of synthetic enamel paint over one coat of primer all as specified and directed as in cupboard shutters.

S&F in repairs PVC corners fixed in bath rooms with screws including necessary drilling holes. Make : Prayag Cat no - 192 or equivalent as approved by GE.

Disconnecting existing water tanks, setting aside (or lowering if required) for repairs, cleaning etc capacity of tank exc 500 and n.exc 1000 ltr complete all as specified and directed.

S & F rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 500 ltrs including taking down existing tank also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms)( Make of tank Sintex cat no CCWS 0075-02-TLW or equivalent of makes given in Appendix B to PS Make of ball valve Prayag or equivalent in polytuff as approved by GE

S & F rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 750 ltrs including taking down existing tank also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms)( Make of tank Sintex cat no CCWS 0075-02-TLW or equivalent of makes given in Appendix B to PS Make of ball valve Prayag or equivalent in polytuff as approved by GE

S & F rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 1000 ltrs including taking down existing tank also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms)( Make of tank Sintex cat no CCWS 0075-02-TLW or equivalent of makes given in Appendix B to PS Make of ball valve Prayag or equivalent in polytuff as approved by GE

S&F, in repair 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium road and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F, in repair 20 mm bore gun metal globe / gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F, in repair 15 mm bore gun metal globe / gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Demolition of cement concrete of exc 15 cm thickness but above ground floors all as specified and directed by engr-in-charge

M&L for PCC 1:5:10 type E-2 (using 40mm graded aggregates ) mass conc as in sunkun portion floors, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof kerbs/coping/ bed block /padding/ depression complete all as specified and directed.

Taking down existing water proofing tretment on RCC slab / beams with bitumen felt with out damaging structure and removing the debrise outside the MD land and M&L for plaster 15 mm thck on concrete surfaces in cement mortar 1:4 finished even and smooth using WPC @ 3% by weight of cement and preparing the surfaces to recive WPT treatment , applying a coat of bitumenm primer confirm to IS - 3384-1986 @ 3% per sqm . providing APP modified memrane with non woven polyster reinforcement/mat ( centre core) by tourch application over primed surfaces all as specified and directed by Engr-In- Charge

S&F in repair GI spouts of 40 mm dia pipe , approxly 700mm long in sunken floors including necessary cutting , chipping of walls and making good with PCC 1:2:4 type B0 or cement mortar 1:3 with WPC, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exc. 0.06Sqm but n.exc. 0.11Sqm as per IS - 13755 in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed 15mm thick in cement mortar 1:6 complete as directed by EIC.

S & F in repair chicken wire mesh with tack screws of galvanized mild steel wire cloth of 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as spd and as directed

S&F, in repair expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples fixed to walls, steel members complete all as specified and directed .

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih stainless steel wire staples.

Taking down carefully old metro flush internal parts and servicing the parts including replacing the parts which are not functioning / serviceable and re-fixing the all internal parts of metro flush in position in existing opening complete all as directed. Note: (i) Supply only new parts of metro flush shall be measured and paid separately against the relevant items here-in-after (iii) The parts of metro flush shall be of the same make as per existing or equavalent as approved by GE.

Supply only push control cock.

Supply only Sleeve

Supply only Wall flange

Supply only Lock

Supply only Spring Cap / Key

Supply only Spring

Supply only Seal Washer

Supply Body Nut

Supply only O-Ring Small Size

Supply only O-Ring Large Size

Supply only stopper Bush

Supply only sealed piston and spindle

M&L for preparation of new or previously untreated concrete or PCC block masonry external surfaces and applying two coats of exterior emulsion paint (in camouflage pattern as approved by the GE) over a coat of primer all as specified and directed by EIC using any one of following material :- Make Brand Nerolac Suraksha Asian ACE Berger Walmasta Indocem Birdnest1600

M&L for preparation of old painted sufaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint on steel and iron surfaces on roof coverings in camouflage pattern (as approved by GE), complete all as specified and as directed.

M&L for complete removal of existing treatment & preparation of plastered or unplastered old decorated external surfaces of walls and applying two coats of exterior emulsion paint in camouflage pattern as approved by the GE, all as specified and directed using any one of following material :- Make Brand Nerolac Suraksha Asian ACE Berger Walmasta Indocem Birdnest1600

M&L writing letters or figures (block roman) italic or indian not exceeding 15 cm high and 3 cm in width complete all as specified.

M&L writing stops, commas, short lines,dashes, hyphens, brackets etc complete all as specified.

ASHAPURA CONTRACTOR

Jyoti Refrigeration

sudarshan builders

Ahmed B Khatri

Hi-Tech Systems

M/s Pal Builders

Bhavik Construction

Sanjay Enterprise