SPL REPAIR TO BLDG P-95 (ACUTE WARD), SPL REPAIR OF LIGHTENING CONDUCTOR SYSTEM AT MH BHUJ AND CONSTRUCTION OF VEHICLE SHED AT 75(I) INF BDE UNDER GE ARMY BHUJ

M&L for brushing neat cement slurry with 3 Kg/Sqm of cement complete incl complete removal of existing roof treatment all as specified and directed.

M&L for 40 mm thick PCC of type B-0, 1:2:4 (12.5 mm graded aggregate) for padding all as specified and directed

M&L Rendering 10 mm thick of CM 1:4 on concrete roof surfaces is to be finished even and smooth without using extra cement complete all as directed.

M&L in repairs App based polymeric membrane minimum weight 3.5 Kg/Sqm and Minimum 3 mm thick reinforced with polyester non wove fabric (Wt. not less than 150 gms/Sqm land on primed surface by forced application completed all as specified and directed

M&L cleaning surface and applying two coats of aluminium paint on roof or vertical surfaces complete a ll as specified and directed

Cutting chase in brick walls, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealing APP membrane etc and making good, cutting not exc 10cm girth complete all as specified and as directed

Supply only Integral WPC complete all as specified and directed. (Make:Pedilite/Roft/Fosroc/Bauchemic India/Cico)

Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above ground level) complete all as directed.

M&L Cement concrete ( 1:3:6) type C- 2, using (40mm graded stone aggregate) 75 mm thick as in sub base /plinth protection etc. Finishing cement concrete surface even and smooth without using extra cement complete all as directed

M&L for Preparation of old painted surface of steel and iron surface of any description and in any position over 10 cm width or girth and M&L for applying one coat of synthetic enamel paint complete all as specified and directed.

Providing & fixing hard drawn MS steel wiremesh 80mm x 25mm with 3mm dia wire with Heavy duty nails, Fixing the mesh on the ceiling before shotcreting work complete all as directed.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed

M&L Rendering 15 mm thick of CM 1:4 on fair faces of brick or concrete surfaces is to be finished even and smooth without using extra cement with mixing of water proofing compound complete all as directed.

M&L Rendering 10 mm thick of CM 1:6 on fair faces of brick or concrete surfaces is to be finished even and smooth without using extra cement with mixing of water proofing compound complete all as directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L Providing and applying cement base plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces with smart painting tools complete all as specified and directed

M&L for Preparation of old surfaces by complete removal of existing treatment and applying two coats of oil bound distemper over one coat of primer on walls & ceiling complete all as specified and directed

type C-1 for earth pit and 40 mm thick precast RCC cover in 1 : 2 : 4 type B-1 with 3 Nos 8 mm dia TMT bars both ways with 12mm dia round bar handle complete all as specified & directed. NOTE: Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item and additional earth GI earth wire/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item of Schedule `A’

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

M&L for preparation of the newly plastered surfaces of walls,ceiling & applying two coats distemper oil- emulsion , white or tinted over a coat of primer surfaces of wall complete all as specified and directed

Providing & applying Rising damp-proof coating system with Single component ready to use damp-proof coating Roff Hydamp : 1.SURFACE PREPARATION: Thoroughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc. All large voids or hollow portions must be removed and re-plastered. Non- moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2 APPLICATION: Apply the first coat of Dr Fixit Dampguard Classic with a paintbrush directly on the prepared surfaces by mixing ( 1 part base:1 part hardner: 1 part of water) . Allow to dry for a minimum 2-3 hrs. Apply one part of DAMPGUARD mixed chemical and 2 parts of OPC white cement/Birla Putty and make the Putty, apply Putty on the entire surface area. Allow it to dry for at least 3-4 hours. Apply the Final coat of Dr Fixit Dampguard Classic on the entire surface and allow the surface to air cure 48 Hrs proceeds to paint.complete all as specified and directed

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed

S & F anodised Aluminium alloy sections sliding windows with frames Series-C (20mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 5mm thick and stainless steel wire cloth 0.35mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed

M&L for moulded grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with suitable aluminum frame of size 37x19x2mm complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L for Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified Note : Panel filling i.e.. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately

S&F 12 mm thick prelaminated particle board, Exterior grade prelaminated and both sides with decorative choice laminations complete all as directed.

S&F in repair Tee grid suspension system of size 600 mm x 600 mm type-1 made out of roll framed hot dipped galvanised steel zince coated of not less than 120 gm/Sqm, main runner 0.3 mm thick of section 24 mm x 33 mm crross runner 0.30 mm thick of section 24 mm x 25 mm, wall angle shall be 0.63 mm thick of section 24 mm x 24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod, system exposed portion shall be pre painted polyester coated in off whitee/white in colour complete with material, fixing, jointing etc., with Coloured textured designer ceiling board 4mm thick of size 595 x 595 mm fixing with screws/clips complete all as per manufacturers instructions and direction.

S&F solid PVC door frame of size 50mmX47mm made out of 5mm both side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening all as per specifications and drawing shown on sl page No 150 of SSR part II (for item-884).complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & both side prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of both side prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required & directed

S&F 2nd class hard wood factory made plain framed panelled door shutters 35mm thick with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides. The size of rail and stiles as per IS:1003 (Part I), Klin seasoned and chemically pressure treated.complete all as specified and directed.

S&F for butt hinges 100mm size medium weight stainless steel .complete all as specified and directed

M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed

S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed

S&F stainless steel sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L for glazed ceramic tiles, coloured tiles, 450X300 x 7mm thick on vertical faces i.e.. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

M & L for non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.complete all as specified and directed.

Supply and fix single point air termination aluminium rod, 12 mm dia, 300 mm long completed all as specified and directed.

Material & labour for machine cut kota stone slab size as in flooring, stair case landing. treads of steps, 18-22mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm thick screed bed or bedding in cement mortar 1:6 all as specified and directed

Material & labour for machine cut kota stone slab size as in skirting, dado, vertical surfaces etc, 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including backing coat 15mm thick cement mortar 1:3 complete all as specified

M&L Granite slab work 18-20mm thick in floors steps, cooking platforms and like including pointing in white cement with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 including cutting recess opening for the sink portion and embedding complete all as specified and directed by Engineer-in-Charge. (Note : No deduction shall be made for opening of sink portion, shall deemed to be included in the quoted rate) complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and othersimilar situations complete all as specified and directed.

S&F for Rotational moulded polyethylene water storage tank(white) of 1000 liter capacity (cylindrical vertical with closed top incl float valve) hoisted and fixed in position all as specified and directed

S&F in repair vitreous china wash basin, white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated fancy type pillar tap 15mm bore, screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipecomplete all as specified and directed.

S&F in repair PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed

S&F in repair vitreous china Wash down water closet (pedestal pattern), complete including Pedestal pan and trap and seat cover, including connection to drain ( or outgoing pipe) and flushing pipe, antisyphonage pipes etc (excluding flushing cistern and flush pipe) complete all as specified and directed

S&F in repair vitreous china urinal Flat Back Half Stall (HxWxP): 345X320X560 mm white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and white pipe) and providing fixing of plugs bedding urinal against wall including taking down the old one complete all as specified and as directed. (Make : Prayag Cat No 4998 or equivalent of Cera / Parryware) complete all as specified and directed.

Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 16 mm dia, any grade, of any description or in any position including fittings complete all as specified and directed

Taking up or down existing unserviceable upvc/ mild steel water tubin

g and connections 20 mm dia, any grade, of any description or in any position including fittings cocomplete all as specified and directed

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 75mm set in cement mortar complete all as specified and directed.

Supplying and Laying 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supplying and Laying 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 110mm set in cement mortar and taking out of trenches, if required complete all as specified and directed

S&F for 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F for 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S & F in repairs 15mm dia 2-in-1 bib tap with angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT) complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius with access door.complete all as specified and directed

S&F 110mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S & F in repairs 15mm dia angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107053 OR EQUIVALENT) complete all as specified and directed

S&F in repairs 15mm dia Bib taps cast copper alloy, with Chromiun plated crutch or butterfly handle screwed down,for iron pipe or brass ferule complete all as specified and directed. (Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. APR -101037 OR EQUIVALENT)

S&F in repair health faucet spray type jet with brass jet, chromium plated, and 1.0 m long PVC flexible pipe complete all as specified and directed .(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT)

M &L mild steel bars conforming to Fe 290 Gde E-165 as in guard bars ,ladder or similar works including welding etccomplete all as specified and directed

Demolition of concrete block masonry built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry (Type C1, 1:3:6, 20mm aggregate) with solid blocks, exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed

S&F 18 mm thick prelaminated PVC Cheluka ply prelaminated one side with decorative choice lamination and other side plain fixed with screws to PVC celuka ply works all as directed and as per manufacture instructions Make : Rajshree plasticwood complete all as specified and directed.

S&F brass Handle fabricated type polished of Size 100 mm complete all as specified and directed.

S&F brass Handle fabricated type polished of Size 75 mm complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise spefifically provided for.complete all as specified and directed.

S&F for butt hinges 100mm size medium weight stainless steel .complete all as specified and directed.

Suface excavation n.exc 30 cm deep & avg 15 cm deep & getting out in any type of soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm as in any type of soil complete.

M&L, PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

Removing excavated material at a level n.exc 1.5 m above the starting point 50 mtr deposting where directed.

S&F roof trusses (framed), vertical pole , trussed, pirline, crane gantries rails and fastenings and heavy bracket framing (beam tea angle chanell or flat section ) including distance pieces, cleats etc confirming to Fe410-W (grade E-250) quality A completed all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50mm thick of an color having tensile strenght of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers All as specified and Directed.

M/L for two coat of enamel paint (Ist quality) over a coat of red oxid primer on new steel surface including preparation of surface over 10 cm width or girth all as specified.

Supply and laying 40 mm bore galvanized steel tubing, medium grade (For fixing air termination rod as pipe post with all fittings laid in trenches/ road /etc complete as all specified and directed.

M&L for PCC 1:3:6 type C-1 using 20 mm graded aggregated as in copings (150x150x200 mm) for holding GI pipe kneelers, apex stones, bed plates, kerbs etc. water trouhs and the like including weatheering, slightly rouded or chamfered angles and throating including necessary form work complete all as specified and as directed.

Supply and fix Earth continuity conductor or main earthing lead fixed to wall on insulator or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation etc. as required of size 32 mm x 6 mm galvanised iron srip all as specified and directed.

Supply and fix Earth continuity conductor or main earthing lead fixed to wall/roof on insulator or racess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required of size 25 mm x 3 mmaluminium srip all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x600mm buried directly in ground vertically to a depth not less than 2.25 metre belows normal ground level (with top edge of earth plate not less than 1.5 metre below ground level) connected to galvanized iron earth strip 32x6 mm dia, (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate 15 mm dia GI pipe medium grade for watering pipe with funnel & wire mesh complete all as specified & directed. Note:- Earth lead wire and its proctection pipe uoto and including 7.5 mtr only from the top of earth electrode are included under this item and additiional earth GI earth wire/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item f Schedule 'A'

Supply and fix test point termination block of size 75 mm x 75 mm x25 mm made of gun metal or phospherous bronze drilled and screwed including 3 Nos, 8 mm dia 25 mm long hex head screw and box of size 90 x 90x 90 mm (made out of 1.6 mm thichplain brass sheet ) and screwed to wall for protection of test point complete all as specified and directed.

Point

M&L for point wiring with using 1.5 Sqmm (nominal area) multi standard copper conductor, single core, FRLS PVC insulated & unsheathed cable, 1100 volts grade with and including PVC conduit pipe of adequate size concealed type on wall / fixed to surface ceiling with PVC rawl plugs with sunken type pressed steel terminal box suitable for laminated board or Modular fititng board and junction boxes 1.6mm thick of suitable size, duly painted with one coat of red oxide primer and two coats of black bituminous paint for mounting fittings and wiring to be

terminated in pressed steel sunken boxes with and including all accessories and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, FRLS PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed for following:- NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes to required depth & making good the disturbed surface in CM 1:4 including finishing the surface to match with the existing surface. (ii) Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iii) The quoted rates shall be deemed to be inclusive for provision of white cover plate and frame all as specfied and directed

One light/buzzer point controlled by one; one way switch.

One fan/exhaust fan point controlled by one, one way switch

M&L for Preparation of old painted surface of wood and wood based material any description and in any position over 10 cm width or girth and M&L for applying one coat of synthetic enamel paint complete all as specified and directed.

One 3 pin socket out let 5 amp (independent) point controlled by one; one way switch.

One 3 pin socket out let 5 amp point on the (same board) with other switches.

S&F ceiling rose surface bakelite 63.5 x 20 mm, three terminals, complete all as specified and directed

Supply and fix modular switch 6 Amp, one way, 1 module, 230 volts AC circuit complete all as specified and directed

Supply and fix modular switch 16 Amp, one way, 1 module, 230 volts AC circuit complete all as specified and directed

Supply and fix modular socket, 6 Amp, 2/3 pin combined, 2 module, 230 volts AC circuit complete all as specified and directed

Supply and fix modular socket, 6 /16 Amp, 2/3 pin combined, 2 module, 230 volts AC circuit complete all as specified and directed

Supply and fix modular fan regulator 120 W 2 module complete all as specified and directed by Accepting officer

S & F in repairs earth plug and socket, single pole, neutral sheet metal enclosures with a two pin, plug and socket 20Amp, 240 volts with and including one MCB, SP, 20A, 240 Volts as per all as specified and directed.

S & F in replacement elegantly industrial general purpose box type luminaire, 1x20 Watt, designed box type LED luminaries, CRCA sheet steel housing with white reflector cover fitted to the body with decorative end covers complete with spring loaded rotor type lamp holders, connected block with and including 01 No LED lamp 20 Watt and all accessories, pre-wired and connecting the same to ceiling rose with & including three core PVC insulated and sheathed copper conductor 23/0.0076 cable including all accessories and fixing arrangement for fixing the light fitting to walls / roof surface over and including 2 Nos PVC square box complete all as specified and directed.

S & F in replacement 10 W mirror light having indirect up down light for mirror and as well light application with CCT 6000K, including LED Bulb/Module and Electrical connection with 3 core flexible wire of appropriate size from ceiling rose to the tubelight fitting, all as specified and directed.

S&F lamp holder PVC / Polycarbonate type with cord grip cap suitable for LED lamp fitting complete all as specified and directed

Taking down carefully MCBs, Metal clad plug, distribution boards/main switches of any type and size and S & F sheet metal enclosure powder painted for MCB DB SPN 08 way double door with IP-42 protection with Din rail and busbar complete all as specified and directed .

Taking down carefully MCBs, Metal clad plug, distribution boards/main switches of any type and size and S & F sheet metal enclosure powder painted for MCB DB SPN 12 way double door with IP-42 protection with Din rail and busbar complete all as specified and directed

S&F sheet metal enclosures for distribution board when MCB to be used VTPN ( Triplepole and neutral ) 4 way busbar type , 415Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type, with MCCB 100A complete all as specified and directed.

S&F in Repair MCB TPN, 63 Amps,415 Volts, rupturing capacity 10 KA."C" Series complete all as specified and directed.

Supply and fixing in Repair MCB SPN, 6 to 32 Amps in `C’ series having current rating 10 KA complete all as specified and directed.

S&F in repair MCB single pole, 6 to 32 Amps in `C’ series having current rating 10 KA complete all as specified and directed.

Taking Down Old Unserviceable Submain wiring complete including all accessories and making good the disturbed surfaces all as specified and as directed.

M/L for Sub main wiring with 2 runs of PVC insulated unsheathed multi stranded single core copper conducter 6 Sqmm drawn through PVC conduit/casing capping including accessaries with 6 sqmm PVC insulated earth wire fixed to the existing wall with saddles, screws etc after removing the unserviceable wiring and connecting up ,all as directed. Note: 2 runs of cable and one run earth wire and conduit/Casing & Caping will be measured as one length.

M/L for Sub main wiring with 2 runs of PVC FRLS insulated unsheathed multi stranded single core copper conducter 4 Sqmm drawn through PVC conclead conduit including accessaries with 4sqmm PVC insulated earth wire fixed to the existing wall with saddles, screws etc after removing the unserviceable wiring and connecting up ,all as directed. Note: (a)2 runs of cable and one run earth wire and conduit will be measured as one length. (b) cutting chases in to the wall of any thickness , fixing suitable size conduit and drawing copper conductor and and make odd the disturbed surface to match with the existing surface after pluging the holes complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing electric water heater, storage type steel body with inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

M&L for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level (with top edge of earth plate not less than 1.5 metre below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe medium grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia medium grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6)

NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.