PROVN OF TIFFIN ROOM, STATIC WATER TANK, RAISING OF BOUNDARY WALL AND PAVED AREA AT DIFFERENT LOCATIONS UNDER GE (I) NAVY PORBANDAR

Amount

Surface dressing not exceeding 15 cm deep in hard and dense soil.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc, not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in hard/dense soil, complete all as specified and as directed.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc, not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/disintegrated rocks, complete all as specified and as directed.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/dense /soft disintegrated rocks including cutting of bushes, saplings and cutting trees not exe 30m girth etc complete. Note:- Area of surface dressing and surface excavation are not payable simuletenously.

Excavating over areas, n exc 1.5 m deep and getting out in soft/disintegrated rocks.

Excavating over areas, exc 1.5 m but n. exc. 3m deep and getting out in soft/disintegrated rocks..

Returning filling including spreading, levelling watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified.

Returning, filling in of soft/disintegrated rocks including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified & directed by Engr-in-charge.

Removing excavated soils exc. 500m n. exc. 1.5Km and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L RCC M-30 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L RCC M-30 (using 20mm graded stone aggregate) as in columns, etc, complete all as specified and directed.

RCC M-30 (using 20mm graded stone aggregate) as in lintel beam ,roof beam etc, complete all as specified and directed.

RCC M-30 (20 mm graded aggregate) as in roof slab, projections supported on walls, beams and columns in roofs etc. complete all as directed.

RCC M-30 (using 20mm graded stone aggregate) as in chajjas etc, complete all as specified and directed.

Use & waste of formwork to rough finished surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work all as specified & directed by Engr-in-charge. .

Use & waste of formwork to sides of columns, square, rectangular etc, complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., work in rough finished flat surfaces of concrete, complete all as specified and directed

Use & waste of formwork to chajjas including edges etc, complete all as specified and directed.

Use & waste of formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs and similar work; not exc 200 mm thick (horizontal or sloping), complete all as directed.

Mild steel CRS bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Mild steel CRS bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Mild steel CRS bars 8mm dia and over as in stirrups spacer and binder, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Dressed Porbandar stone masonary walling of squared walling in cement mortar 1:6,complete all as specified and directed

Dressed Porbandar stone masonary walling of squared walling in cement mortar 1:4 as in half thick stone wall, complete all as specified and directed

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering, complete all as specified and directed

Treating the top surface of filled earth with anti termite emulsion at the rate of 5 litres per square metre of surface area, complete all as specified and as directed.

Treating the soil under plinth protection with anti termite emulsion at the rate of 5 litres per square metre of surface area, complete all as specified and as directed.

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

75 mm thick PCC 1:3:6 type C2 as in plinth protection finished even & smooth without using extra cement complete all as specified and directed.

75mm thick PCC type D2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

S&F Vitrified coloured Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match Complete all as specified and directed.

S&F Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match Complete all as specified and directed.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite Complete all as specified and directed.

Coloured Glazed ceramic tiles in vertical surface 450X 350X 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match on vertical surfaces such as skirting, dados and risers to steps etc. set and jointed in neat cement slurry and jointed in white or colour cement to match. Complete all as specified and directed.

M&L Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes etc.complete all as specified and directed.

M&L Screed bed or bedding layer of mortar 10 mm thick in CM 1:4 for skirting/dado etc.complete all as specified and directed.

M & L rendering 5mm thick,on fair faces of concrete surfaces in cement mortar 1:3 on ceiling ,finished even & smooth with out using extra cement including using 3 mm wall care putty to obtain even and smooth surface, complete all as specified and directed.

M & L rendering 10mm thick,on fair faces of stone masonry surfaces or concrete surfaces on wall in cement mortar 1:6 finished even & smooth with out using extra cement , complete all as specified and directed.

M & L rendering 20 mm thick in two layers (15+5) ,on fair faces of stone masonry surfaces or concrete surfaces in cement mortar 1:6 finished even & smooth with out using extra cement including use of water proofing compound in outer layer, complete all as specified and directed.(Note- Water proofing compound use against this item measured and paid seperately )

Supply only liquid water proofing compound as per Manufacturer Instructions complete all as specifried and directed.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling , complete all as specified and directed.

M&L for preperation of newly plastered wall surfaces with 2-3mm wall care putty and applying two coats of oil bound distemper on internal walls over a coat of primer ,complete all as specified and directed .

M & L for two coats of acrylic emulsion weather proof antifungal paint on newly plastered surfaces of wall or concrete surfaces in two coats including preparation of surfaces and one coat of primer complete all as specified & directed by Engr-in-charge.

Powder coated anodised aluminium frame for windows (Three track) sliding type,with one or more rebates including jointing cleat for fixing etc ,complete all as specified and as directed.

Powder coated anodised aluminium window shutter,fixed type without sash bar ,aluminium sections weighing 0.55 Kg/m including necessary jointing cleats ,glazing clips,rubber packing,anodised aluminium snap beading,srews etc ,complete all as specified and as directed.

Glass sheet ordinary quality,4.0 mm thick,in squares exceeding 0.5 sqm each pane,complete all as specified and as directed.

Aluminium deco grill pattern DG-104 5.5 mm to 6.5mm thick with necessary chanels and clips.

Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

IInd Class hard wood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F for flush shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides.

Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Factory made solid panel PVC door shutter, 30mm thick (style consisting of frame made out of MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stile and plain colour PVC sheets for top rail lock rail & button rail on either side and as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, suppling & fixing in the frame at site as per manufacturer's instruction, specification & drawing shown on page 146 of SSR Part-II 2004.

Aluminium alloy, anodised, sliding door bolt 300mm,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed Complete all as specified and directed.

Aluminium anodised, barrel tower bolts 200mm long of ex- truded section and fixed , Complete all as specified and directed.

Aluminium handles, cast type, anodised 150mm long , Complete all as specified and directed.

Butt hinges stainless steel type C 21,125mm fixed with screws,Complete all as specified and directed.

Door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor over all length of cover 150 mm , complete all as specified and directed.

100 mm dia PVC (SWR) `S' trap , complete all as specified and directed.

75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement , complete all as specified and directed.

75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , complete all as specified and directed.

100 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , complete all as specified and directed.

75 mm dia PVC (SWR), junction single, (Single T) equal or unequal

100 mm dia PVC (SWR), junction single, (Single T) equal or unequal

75 mm dia PVC (SWR) vent cowl

100 mm dia PVC (SWR) vent cowl

Cast iron bend (any radius) diminishing pieces or tapers ( larger bore measured), for 100mm bore cast iron pipes.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement,

Rotational moulded polytheline water storage tank 500 Ltrs capacity ( cylinderical / vertical with closed top) hoisted and fixed in position.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 20mm pipe outer dia, Complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. 25mm pipe outer dia, Complete all as specified and directed.

S&F soap dish PTMT any colour fixed to plug with chromium plated brass srew,complete all as specified and as directed.( Make- Prayag/Polytuff/Symet )

S & F bib tap 15 mm bore chromium plated cast type copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or brass ferrule.

S&F Stop Valve (Angle Valve) 15mm bore size chromium plated fancy type complete all as specified.

S & F Vitreous china wash basin, table top min size 550 x 400 mm including waste pipe waste fitting, brackets and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug .

S&F Pillar tap swan neck 15mm bore fency type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F Waste coupling of PTMT for 32mm bore dia of discharge pipe (half or full threaded) . (Minimum weight 32mm-45gms/40mm-60 gms)

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F 32mm dia Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm

S&F Vitreous china down water closet pan (Pedestal patterns) white/ivory fixing bolts, flushing cistern and flush pipe incl connection to trap and flush pipe anti syphonage pipe etc and to flushing pipe, anti - syphonage pipe etc., complete all as specified and directed.

S&F PVC flushing cistern 10 ltr capacity incl PVC connection inlet and and outlet connections,brackets, PVC flush pipe with bend 32 mm dia of suitable length including making necessary connections to water supply pipe line and jointing to WC, complete all as specified and directed.

S&F PTMT towel rail of superior quality 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms),complete all as specified and as directed.( Make- Prayag/Polytuff/Symet )

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed

M&L for 10 mm thick (average) screed bed in CM (1:4) in order to maintain proper slope and base over existing roof surfaces for laying of membrane, finished even and smooth without extra cement complete all as specified and as directed. Note:- Polymeric membrane will be measured and paid separately

M&L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment / specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 3 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non wovwn polyster fabric or weight not less 150 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm 9 minimum) and then inserted insde the groove of parapet wall and shall be finished by a membrane flashing. Note:- (i) Laying of APP based membrane shall be done by torch on method or as per manufacturers instruction. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instruction. (iii) Applying two coats of Bituminous aluminium paint on top of APP membrane.

M&L for cement concrete 1:3:6 type C2 ,Concrete bed to drain pipes of 150 mm dia including packing under, and hunching against the sides of pipes after they are laid and tested; in

M&L precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate as in Manhole cover slab , complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in benching in man hole etc all as specified and directed.

M&L Reinforced concrete pipes, class NP2, laid and jointed complete with collars of nominal dia 150mm, all as specified

S&F of 75mm Aluminium handles, cast type, anodised

S&F machine pressed precast concrete interlocking paver block any shape size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment fixced over and including 50 mm thick sand courioning etc all completed

M&L for sand filling under floors or in foundations including watering and consolidation

PCC 1:2:4 type B1(using 20mm graded stone aggregate) as in coping,bed plates, kerb not provided for etc complete all as specified and directed by Engr-in-Charge

M&L 15mm thick rendering in cm 1:6 on stone masonary surfaces or surfaces other than fair faces of brick work or on one side of lathing to be finished even and smooth (without using extra cement) complete all as specified and directed by Engr-in-Charge

M&L for prepration of plastered or unplastered new surface of wall and applying two coats of cement base paint complete all as specified and directed by Engr in charge.

M & L M-30 (Design Mix) for RCC walls, retaining walls, basement walls, ballast walls and the like; any thickness all as specified & directed by Engr-in-charge.

Use & waste of formwork to rough finished surfaces of sides of RCC walls all as specified & directed by Engr-in-charge. .

S&F Mild steel rolled sections Fe 410 -W (Gde- E- 250) quality- A as in framing all as specified & directed by Engr-in-charge.

M & L for Rendering 22mm thick on fair faces of concrete surface in CM 1:4 all as specified & directed by Engr-in-charge.

M & L for two coats of synthetic enamel paint over a priming coat of red oxide after preparation of new surfaces of any description, over 10cm in width or girth,not otherwise described all as specified & directed by Engr-in-charge.

M&L for hard core (broken stone or boulders) of gauge n. exc. 63 mm but n exc 100mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified & directed by Engr-in-charge. .

100mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors.

Site clearance of shurbs, vegtation, grass, bush, weed, trees and saplings not exceeding 30cm in girth, measured at a height of one to two meter above ground level in loose/hard dense soil and disposal off or removed rubbish upto a distance exc 50m and n.exc 1.5Km outside the periphery of the MD area complete all asa specified and directed byEngr-in-charge.

M&L PCC M-10 using 20mm graded stone aggregate as in coping etc and the like including weathering, slightly rounded or chamfered angles and throating, including use and waste of form work all as specified.

Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in cement or cement lime mortar; not previously plastered; and scrubbing down with water etc. to receive plaster

M&L rendering 15mm thick in cm 1:4 in internal surfaces of stone masonry or surfaces other than fair face, finished surfaces even and smooth without using extra cement, complete all as directed by Engr-in-Charge.

M&L two coat of cement base paint on newly plastered surfaces of walls including preparation of surfaces, complete all as directed and as specified.

S&F for mild steel work conforming to Fe-290 grade Fe-165 as in framed work such as grills, gratings, etc, with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bar; barred iron doors, ladder; framed balusters; walk ways; railings; framework of water tanks ans similar work complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided as directed by Engg-in-charge

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L for Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required in hearths; covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required

Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, complete all as specified and directed by Engineer in charge. (each line wire to be measured)

Supply,fixing, testing of monoblock pump set suitable for 415 V, single phase, 3 HP,2.2KW with 3000RPM,fixing on 80X80 Mm dia pipe complete with all accessoriesand electric connection . all as specified and directed by engr-in charge.Make - crompton cat no-monoblock single phase MBQ32(1PH) or eq model of Make specified . Note :- with 2 Years warranty

Supply,fixing, testing of monoblock pump set suitable for 415 V, 3 phase, 5 HP,3.7KW with 3000RPM,fixing on 80X80 Mm dia pipe complete with all accessoriesand electric connection . all as specified and directed by engr-in charge.Make - crompton cat no-monoblock three phase MBQ52(3PH) or eq model of Make specified.Note :- with 2 Years warranty

Supply, fix and installation of Dol Starter for 3 HP motor single phase.including panel with indicator light ameter , voltmeter. make -

Supply, fix and installation of Dol Starter for 5 HP motor single phase.including panel with indicator light ameter , voltmeter. make -

Supply and laying galvanised steel water tubing medium grade ISI marked screwed socketed joints complete with all tube fitting (such as bends,elbow,tees,short pieces,connectors,back nuts,diminishing pieces,caps,plugs and unions,etc) and fixing complete with clips,wall hooks,wooden plugs,or laying in trenches,etc.,also cutting,screwing and waste and for making forged bends on piping as required at etc of following sizes:-

(a) 80 mm dia

(b) 50 mm dia

(c ) 40 mm dia

(d) 25 mm dia

Supply and fixing gun metal gate valve screwed down high pressure with iron wheel head / long shank and cup butterfly type screwed both end for iron pipe .all as directed by engr-in-charge.

(a) 80 mm dia

(b) 50 mm dia

(c) 40 mm dia

(d) 25 mm dia

M & L for 80mm bore dia cast iron sluice valve of pressure class PN-1 type flanged and drilled at both ends, conferming to ISI mark and having gun metal spindle and rings including wheel for operating all as specified including two numbers flanged socket and jointing materials such as bolts, nuts, washers, rubbers/ fibre board gasket complete all as specified and directed by Engr-in-charge.

Supply and fix foot valve conforming to IS 4038,flanged end swing type operation with rubber seat size 80 mm dia.

S&F PVC insulated water proof flat 3 core cable 1100 volt grade submersible cable with copper conductor stranded of size 6 Sqmm.

Material & labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC concealed conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories and sunk zinc coated pressed steel terminal box of 1.60mm thick with 3mm thick plastic laminated sheet top cover, brass screws, cup washers etc including all cutting / chases etc in walls complete all as specified and directed for the followings :-

(a) One light point controlled by one one way switch

(b) One fan/ exhaust fan point controlled by one one way switch

(c) One 5 Amps 3/5 pin socket outlet on same board with other switches.

Description all as per item no 131 above but with using 2.5 sq mm PVC insulated multi-stranded copper conductor for independent switch socket outlet 6 pin 5/15 Amps and incl 1.5 sqmm PVC insulated multi-stranded copper conductor single core as earth continuity conductor wire duly connected to all common earth point, drawn through 20 mm dia PVC surface conduit in any length all as directed at site.

Description all as per item no 131 above but for AC/Geyser Point for 4 sq mm PVC insulated multi-stranded copper conductor for industrial socket outlet 3 pin 16 Amps point and one single core 2.5 sq mm PVC insulated unsheathed copper cable as earth continuity conductor (colour green) fixed to dolly.

S&F Switch piano flush type 5/6 Amps single pole one way 230 Volts

S&F Switch piano flush type 15/16 A single pole one way 230 V

S&F Socket Outlet 2 in 1, 3 pin 5 Amps flush type 230 Volts

S&F Stepped type electronic fan regulator flush type on the existing sheet for 1200 /1400 mm sweep fans complete.

S&F ceiling rose surface bakelite, 65x50mm 2 or 3 terminals complete all as specified and directed.

M&L For Sub main wiring concealed with 6 sqmm (Nominal area) with two runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through Conduit including 4 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point all as Specified and directed by Engr-in-Charge.

M&L For Sub main wiring concealed with 10 sqmm (Nominal area) with two runs of single core cable PVC insulated FR multistrand unsheathed copper conductor cable including 1100 V grade, drawn through Conduit including 6 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point all as directed.

S & F Sheet metal enclosure, DB 4 way ,Single pole and neutral with 200 Amps rated bus bar,230 volts double door type including connecting all connections of wire to MCBs with proper lugs & arrangements, making good to the disturbed surface all as specified and directed..

S&FMCB, DP, 240 Volts, AC of breaking capacity 10 KA C curve of sizes, 40 Amps.

S&F MCB SP 240 Volts AC 6 - 40 Amps of breaking capacity 10 KA C curve. Make : Legrand, Havells or euivalent

M&L Earthing complete with galvanised steel pipe electrode 40 mm bore,medium grade,2.5 mtr in length buried directly in ground with top edge not less than 1.25 metres below normal ground level, connected to galvanised earth wire 4 Sqmm by means of bolts, nuts, check nuts and washers of galvanised iron or steel connected to earthing test point including watering arrangements, with 20mm bore medium grade GI Pipe, PCC chamber, CI frame cover all as shown in electrical plate No 2 including necessary excavation in any type of soil, filling of pit with charcoal & salt in alternate layers & testing complete all as specified. all as specified or indicated including testing on completion by Engr In charge .

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required using GI Wire 4 Sqmm as earthing lead.

Supply and FIX photon ultra 18 watt LED tube light rod single side connection polycorbonate tube light with very high efficacy suited for installation in existing T8 fitting with G 13 lamp holder complete all as specified and directed by Engineer - in - Charge.Make : Havells Cat No :- PHOTONULTRA1213T8SSTL18WLED865SPC or its equivalent of Bajaj/Crompton /Phillips / make specified

Supply and fix fans ceiling complete with electric type regulator and accessories 230 V, 1200 mm sweep (BEE 5 star rated) . Make- Crompton/ Bajaj/ Havells.

Supply and fix Air circulating fans 230v single phase 250 mm sweep. Make -Crompton/Bajaj/ Havells/ make specified.

Chromium plated curtain rod 25mm dia, decorative type including brackets and fixing with seamless steel screw complete all as specified and directed.

Gatral Construction Co.

Vastushilp Building Designer

Parth Infrastructure Pvt. Ltd.

m/s.a.t.odedra