REPAIRS / REPLACEMENT TO STREET LIGHT IN OTM ACCN OF CERTAIN UNITS AT NAA UNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Dismantling & Taking down unserviceable street light fittings LED Fittings/ CFL Fittings,post top lantern,garden light, Pin /Holder type from pole or from Bldgs for repairs including replacement of unserviceable Lamp, holder, integral wiring with appropriate gauge copper conductor and refixing the same after repairs in original position properly using PVC insulation tape or where directed complete including replacement of any spares,cable connections from OH conductors,or from junction boxes to light fitting complete all as specified and as directed. Note : Spares items such as LED driver and cable etc, will be measured and paid separately under respective items.

S&F in repair of the following spare parts in street lights complete all as specified and as directed :-

PVC insulated weather proof sheated alluminium cable 2.5 sq mm 2 core

LED Driver 25 Watt Make Bajaj/Havells/crompton Greaves.

LED Driver 30 Watt Make Bajaj/Havells/crompton Greaves.

LED Driver 45 Watt Make Bajaj/Havells/crompton Greaves.

Dismantaling and Taking down old broken PCC/ Steel pole of any size and depositing to MES store yard complete all as specified and as directed.

S&F in repair New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver. suitable for 43 mm dia bracket size ( max) of rating 25W LED including connecting with 3 core aluminium conducor 2.5sqmm with Overhead conductors or UG Cables complete all as specified and directed. Make-Havells Cat No- ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent of bajaj/Philips/Crompton Greaves/Surya Roshni Ltd/Simoco.

S&F in repair New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver. suitable for 43 mm dia bracket size (max) of rating 30W LEDincluding connecting with 3 core aluminium conducor 2.5sqmm with Overhead conductors or UG Cables complete all as specified and directed Make-Havells Cat No- ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC or equivalent of bajaj/Philips/Crompton Greaves/Surya Roshni Ltd/Simoco.

S&F in repair New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver. suitable for 43 mm dia bracket size ( max) of rating 45W LED including connecting with 3 core aluminium conducor 2.5sqmm with Overhead conductors or UG Cables complete all as specified and directed Make-Havells Cat No- ENDURAPEARLNEOSL45WLED757SASYTOPC or equivalent of bajaj/Philips/Crompton Greaves/Surya Roshni Ltd/Simoco.

S&F in repair LED Post Top Lantern of New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light sourceof 25 Watt LED including fixing on 40mm dia grouted in post complete all as specified and directed. Make-Havells Cat No- CORALPT25WLED757PSYMTOPC or equivalent of bajaj/Philips/Crompton Greaves/Surya Roshni Ltd/Simoco.

S&F path light LED bollard 7W to 10W in cylindrical shape with opal acrylic diffuser and IP 65 & IK-10 protection with silent observer and giving light, diffuser at the upper portion acts a beacon of path guidance in a landscape enironment fixed on PCC (1:4:8 )type D2 using 40mm graded crushed stone aggregate complete all as specified and directed.

M&L for mounting bracket made out of 32 mm dia GI pipe medium grade 120 cm long cut to size and bend to shape , fixing on poles with flat iron clamps 40mm x 6 mm – 02 sets including nuts, bolts and washers including one coat of aluminium pait over acoat of red oxide primer including taking down of old unserviceable complete all as specified and directed.

S&F in repair of junction boxes with new Thermoplastic Cable Junction Boxes IP66/67 "weather proof" , for outdoor installation with knockouts for cable entry with terminals suitable for 10-16sqmm cable off Size 155 X 210 X 92 mm incl busbar fixed in repairs and including Necessary civil works and connecting all incoming and outgoing wires with AL lugs of appropiate sizes complete all as specified and directed. Make-Hensel Cat No-KF1616G or its Equivalent.

M&L for fabrication of Sheet metal enclosure , powder coated of Timelite Distribution Boards for automatic Switching of street lights internally pre wired by using suitable copper lugs including fixing with MS Clamp made out of FI (40X5) mm to steel/RCC poles incl connection consisting of the following (i) ASTRONOMICAL time switch 24 hrs operation 240 Volts complete all as specified and directed. (Make-L&T Cat Part No-AUTS02AST00 or Equivalent of Legrand/Scneider.) (ii) 3 pole contactor 40Amps. Make-L&T Cat No-CS 94190 or Equivalent of Legrand/Scneider.) (iii) MCB FP 32 Amps. Make-L&T Cat No-BB40320C or Equivalent of Legrand/Scneider.)

S&F in repair Time Switch, Digital control,Astronomical type suitable for daily operation in 230 volts AC supply complete all as specified and directed. Make-L&T Cat No-AUTS02AST00 or Equivalent of Legrand/Scneider.)

S&F in repair three pole power contactor with control relay with AC Coil suitable for operation in 415 volts AC supplywith 230 volt relay coil and current rating 40Amps complete all as specified and directed. Make-L&T Cat No-CS 94190 or Equivalent of Legrand/Scneider.)

S&F in repair MCB FP 32A 'C' Type for operation in 230/415 volts AC supply complete all as specified and directed. Make-L&T Cat No-BB40320C or Equivalent of Legrand/Scneider.)

S&F in repair earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre below ground level) with top edge of the earth plate not less than 1.5 metre below ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part I connected to earth test point all as specified or indicated including excavation and connected earth work, in soft/loose soil, removing soil upto 50m, PCC 1:3:6 type C1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm bore GI medium grade earth lead protection pipe, 50mm thick RCC 1:2:4 type B1 cover slab of earth pit reinforced with 8 mm dia TMT Bars @ 10cm C/C both ways and with handle made out of 20mm dia bars, funnel, strainer, alternate layer of charcoal dust and common salt and testing on completion ,complete all as specified and directed.

S&F in repair cross arms, bracings, supports, clamps, straps D-clamps, back plates and MS frames fabricated from structural steel sections such as MS channel, angle iron and flats etc including nuts, ,bolts, washers eye hooks, welding, bending cold or hot drilling holes for bolts in any shape or size including two coats of synthetic aluminium paint over a coat of red oxide primer after preparation of steel surface complete all as specified and directed.

S&F in repair shackle type Insulator porcelain vitreous white/ brown or green, 75 mm high and 90mm dia suitable for working pressure of 1100 Volt including Galvanized mild steel straps of size 31x3 mm , nut, bolt of dia 12 mm and washers of suitable size, complete all as specified and directed.

S&F in repair pin Insulators Porcelain vitreous white or green including Galvanized mild steel spindle, two GI washers and one GI nut of size suitable for 1100 Volt electric pressure complete all as specified and directed.

Supply & Erecting in repair Steel Tubular Swaged Pole Type 410-SP-31 (9.0 mtrs long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying two coats of Black Bituminous paint from bottom End of Pole upto PCC Coping and applying with two coats of Aluminium Paint over a coat of Primer (Externally from Top of Coping), including necessary earth work, excavation, PCC 1:3:6 using 40mm graded sone aggregate for foundation and coping with PCC 1:2:4 using 20mm stone aggregate and smooth finish complete all as specified and directed.

Taking down LT UG Cables of any size from trenches/poles complete after disconnection complete all as specified and directed.

Supply, laying, jointing and testing LT cable in trenches or on poles / walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm, 2 core complete all as specified and directed.

Supply, laying, jointing and testing LT cable in trenches or on poles / walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm, 2 core complete all as specified and directed.

Supply, laying, jointing and testing LT cable in trenches or on poles / walls, XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm, 4 core complete all as specified and directed.

S&F in repair 32 mm dia GI tubing light grade with all necessary fittings laid in trenches, fixed to walls/ poles/ under road/ floor etc for cable protection, complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations etc, or for shafts, wells, cesspits, man holes, pier holes etc not exc 10 sq m on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft / loose soil complete all as specified and directed.

Removing excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L for Sand Cushioning using clean,dry angular sand completely free from organic and other harmful matters in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 cm (8 cm in depth before laying the Cable and 15 cm after laying the Cable) and consolidated (punned) upto 18cm thickness,complete all as specified and as directed. NOTE : Punned thickness of Sand Cushioning shall only be measured and consider for payment.

Supply and laying in trenches brick common burnt clay building brick, sub class 'B' designated- 75 with width equal to length of brick for cable protection complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in foundations of Poles and filling of mass concrete complete all as specified and as directed.

M/S L N ENTERPRISE

M/S Deep-Jeet

M/S MOHANPASARI