SPL REPAIRS TO SINGLE JCOS BLOCK (BLDG NO. P-293) AND SPL REPAIRS TO BLDG NO P-273 JCOS SINGLE LIVING ACCN AT 2075 FD HOSP AT MIL STN BHUJ UNDER GE ARMY BHUJ

Amount

M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd (and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction Stage 5:- Making holes in wall and fixing 600mm long 40mm dia GI spout for draining the surplus water if any.

M&L Plain cement concrete 1:4:8 type D-2 using 40mm graded aggrefate as in mass filling in sunken portion.complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed

M&L for 15mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound (Note :- WPC shall be measured & paid separately)

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering on surfaces other than fair faces of brick/concrete surfaces in CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

Supply only Integral waterproofing compound.complete all as specified and directed

Preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) on old/ new plastered @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer on existing yellow coloured surface complete all as specified and directed. Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Interior Emulsion : Asian (tractor shyne) / Berger (bison) / Nerolac (BEAUTY sheen)

M & L for applying three coat of white wash on ceiling over new plaster surface. complete all as specified and directed.

M&L for preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) on old/ new plastered with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed. Make of Exterior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Exterior Emulsion : Asian (APEX) / Berger (WEATHER COAT ANTI DUST) / Nerolac (EXCEL TOTAL).

M&L for applying acrylic wall care putty on old/ new plastered internal/External surfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed. Make of wall Putty : JK wall Putty / Birla Wall care Putty / Bison Wall Putty. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE.

M&L for Preparation of old surfaces by complete removal of existing treatment and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and directed.

M & L for applying one coat of white wash on ceiling over old decorated surface. complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for vitrified ceramic tiles double charged 10mm thick (square/rectangular), polished, coloured (light shade as approved), size of each tile 1200mm x 600mm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed. Make: Johnson (Marbonite)/Kajaria/Somany/ Orient Bell Granito/ Asian Granito/ Oracle Grenito (Marbito)

M&L for vitrified ceramic tiles double charged10mm thick (square/rectangular), polished, coloured (light shade as approved), size of each tile 1200mm x 600mm, as in as in vertical surface like dado/ skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed. Make: Johnson (Marbonite)/Kajaria/Somany/ Orient Bell Granito/ Asian Granito/ Oracle Grenito (Marbito)

M&L for non skid coloured plain/printed glazed tiles of size 300 x 300 x 6mm to 7 mm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for coloured plain/printed glazed tiles of size 600 x 300 x 7 mm, on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L Granite slab work 18-20mm thick in floors steps, cooking platforms and like including pointing in white cement with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 including cutting recess opening for the sink portion and embedding complete all as specified and directed by Engineer-in-Charge. (Note : No deduction shall be made for opening of sink portion, shall deemed to be included in the quoted rate) complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and othersimilar situations complete all as specified and directed.

M&L for preparation of old steel painted surfaces exc 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed.

Taking down shutters of any description and in any position exceeding 1 sqm & not exceeding 2 sqm each complete all as specified and directed.

S & F 35 mm thick factory made IInd class hard wood (not less than Hollock wood) glazed and skelton shutters open rebated and prepare to receive glass / gauze etc (without sash bars) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc {size of members of shutters as specified in clause 8.24 (a) of section 8 of SSR - I} supplied and fitted to chowkat complete all as specified and directed.

S&F 2nd class hard wood factory made plain framed panelled door shutters 35mm thick (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides. The size of rail and stiles as per IS:1003 (Part I), Klin seasoned and chemically pressure treated.complete all as specified and directed.

S&F 18 mm thick prelaminated PVC Cheluka ply prelaminated one side with decorative choice lamination and other side plain fixed with screws to PVC celuka ply works all as directed and as per manufacture instructions Make : Rajshree plasticwood

Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made (ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge including supply and fixing following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 150 mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 nos. per leaf

S & F Powder coated Aluminium alloy sections sliding windows with frames Series-C (20mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 5mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples all as specified and directed.

S&F butt hinges 100mm size medium weight cold rolled mild steel complete all as specified and directed.

S&F for butt hinges 100mm size medium weight stainless steel .complete all as specified and directed.

M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed.

S&F stainless steel sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed.

M&L for preparation of old painted surface of wood and wood based material any description and in any position over 10 cm width or girth and M&L for applying one coat of synthetic enamel paint complete all as specified and directed.

M&L surface preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or grith and apply two coat of synthetic enamel paint over one coat pink primer complete all as specified and directed.

S&F aluminium powder coated ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified.

S&F in repairs 20mm dia powder coated decorative type curtain rod incl brackets complete all as specified and diretced

S&F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with flush pipe 32mm dia complete all as specified and directed. (MAKE - CERA/PARRYWARE)

S & F in repair vitreous china wash basin, white flat back , size 450mmx300mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipe complete all as specified and directed. (MAKE - CERA/PARRYWARE/JAQUAR)

S&F in repair vitreous china Wash down water closet (pedestal pattern), complete including Pedestal pan and trap and seat cover, including connection to drain ( or outgoing pipe) and flushing pipe, antisyphonage pipes etc (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs 15mm dia Bib taps cast copper alloy, with Chromiun plated crutch or butterfly handle screwed down,for iron pipe or brass ferule complete all as specified and directed. (MAKE -CONFIRMING TO JAQUAR CAT PART-No. APR -101037 OR EQUIVALENT)

S & F in repairs 15mm dia angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed..(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107053 OR EQUIVALENT)

S & F in repairs 15mm Concealed stop cock Reduced body with adjustable wall hange or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed..(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107069 OR EQUIVALENT)

S & F in repairs 15mm dia 2-in-1 bib tap with angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed.(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT)

S&F in repairs shower rose 100 mm dia of brass chromium plated fancy type with or without swivel joint suitable for fixing to 15mm bore GI pipe complete all as specified and directed..(MAKE -CONFIRMING TO JAQUAR CAT PART-No. EOS-542N OR EQUIVALENT)

S&F in repair health faucet spray type jet with brass jet, chromium plated, and 1.0 m long PVC flexible pipe complete all as specified and directed .(MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067 OR EQUIVALENT)

S & F in repairs 15mm size PVC connections with PTMT nuts of length 450 mm.complete all as specified and directed.

M&L in repairs 40mm dia Low density poly ethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to wall, ceiling or in floors etc complete all as specified and directed

M&L cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as directed.

S&F for Rotational moulded polyethylene water storage tank(white) of 1000 liter capacity (cylindrical vertical with closed top incl float valve) hoisted and fixed in position all as specified and directed

M&L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 to ends of landings, steps, cills sunshades, shelves lintels etc complete all as specified and directed.

M&L for cutting holes or through PCC block / RCC wall built in CM and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required, superficial area exc 150 sqcm but n.exc 400 sqcm complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 75mm set in cement mortar complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 110mm set in cement mortar and taking out of trenches, if required

S&F for 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches / wall fixed or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid in trenches /wall fixed complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixed complete all as specified and directed

S&F 110mm dia PVC (SWR) branch piece Tee (Single 'T') equal or unequal with acess door.

S&F 75mm dia PVC (SWR) bends any radius with access door.complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends any radius with access door.complete all as specified and directed.

S&F for PVC (SWR) floor trap long body type, plain with grating including jointing with solvent cement

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F for PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

M&L PCC 1:2:4 type B1 using 12.5 mm graded aggregate as in hold fast, cill etc with necessarry form work complete all as specified and directed.

Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 15mm dia, any grade, of any description or in any position including fittings complete all as specified and directed

Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 20mm dia, any grade, of any description or in any position including fittings complete all as specified and directed

Supplying and laying 15 mm outer dia Unplasticised PVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed

Supplying and laying 20 mm outer dia Unplasticised PVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed

Demolition of existing PCC as in form of roof padding incl backing over roof, any thickness including plastering and leaping (where full thickness removed or only a part there of disposal off rubbish upto a distance n.exc 100m, where directed complete all as specified and directed.

M&L for cement concerete type C2 1:3:6 (20 mm graded aggrigate) as in filling and mass concerete etc complete all as specified and dirceted

M&L for 10mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound. (Note: WPC shall be measured & paid separately)

Material and labour for roof surface treated with PU Elastoseal primer with Epoxy Primer to seal the pores and enhance the adhesion of the coating, supplying and applying single component waterproofing liquid membrane based on pure, elastomeric, polyurethane resin cold applied of spray/brush applied membrane with an elongation of 650%+ 50 and tensile strength not less than 2 Mpa, crack bridging ability not less than 2mm. No leakage upto 5 bars of water pressure. Shore Hardness > 50 Shore. The minimum thickness to be applied shall be 1.5 mm, (overall) in two layers (each layer 750 micron) or as per manufacturer’s instructions so as to achieve thickness not less than 1.5mm including providing & laying of protective Geotextile fabric 150 GSM over the entire membrane with proper overlaps of 75mm before laying SRI roof tiles complete all as specified and as directed by Engineer-in-Charge.. Note: (i) The treatment shall be carried out by authorised applicator approved by GE as per the manufacturer Make for PU Primer/ Membrane SIKA/ BASF, BERGER/ STP FOSROC/ SAINT GOBAIN, PIDILITE.

M&L for making benching / Roof Kerbing with PCC (1:2:4) type B0 using WPC as per manufacturer's instruction along side wall adjoining to roof in concave shape complete all as specified and directed. Note : WPC shall be measured and paid separately.

Material & labour for machine cut kota stone slab size as in flooring, stair case landing. treads of steps, 18-20mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm thick screed bed or bedding in cement mortar 1:6 all as specified and directed

Material & labour for machine cut kota stone slab size as in skirting, dado, vertical surfaces etc, 18-20mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including backing coat 15mm thick cement mortar 1:3 complete all as specified.

S&F in repair of PVC cabinet size 650 x 400mm, comprising of looking glass, space for bath soap, shampoo, tooth brush and paste, handle towel rail complete allas specified and directed. Makes: HINDWARE / CERA / NEYCER / PARRYWARE/CLASSIC

M&L 75 mm thick PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in as in sub base all as specified and directed.

M&L for Providing prrecast cement concrete Type B1 1:2:4 (20 mm graded aggregate) in appex stone/kerb stone with plain fair faces including chamfers, weathering throting etc and set in cement mortar 1:4 complete with joints to math size and shape as approved complete all as specified and directed.

M&L sand filling 50 mm thick under floor/over floor or in foundations including well ramming complete all as specified and directed.

M&L 60 mm thick coloured interlocking PCC tiles in approved design/colour set laid over compacted sub soil / sand all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise spefifically provided for complete all as specified and directed.

M&L for removal of existing loose damage concretye, dust, oil, paint, grease, etc from structural member like roof slab, beam, column, chajja, etc exposed fully if any corroded steel in the repair area and remove all the scale and corrosion deposite and applying Dr fixit rust removal and Epoxy Zinc Primer over the cleaned steel bars if and pour the mixed Dr fixit micro concrete into a watertight shuttering after primed by one coat of Dr fixit Epoxy bonding. Thickness or depth of an area n. exc 10cm and all as per manufature instruction as specified. (Note - The rate included S&F of addition reinforcement bars if any required.)

S&F Window Canopy which is made with a durable polycarbonate/Glass/ fiber/acrylic sheet and steel brackets for roof covering/cladding to wall, fixed with hold fast complete all as specified and directed . (Note :As per Design approved by GE)

M&L for preparation of new steel surfaces of any description over 10 cm width / girth & applying 2 coat of synthetic enamel paint complete all as specified and directed

Providing & applying Rising damp-proof coating system with Single component ready to use damp-proof coating Roff Hydamp 1. SURFACE PREPARATION: Thoroughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc. All large voids or hollow portions must be removed and re-plastered. Non- moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2. APPLICATION: Apply the first coat of Dr Fixit Dampguard Classic with a paintbrush directly on the prepared surfaces by mixing ( 1 part base:1 part hardner: 1 part of water) . Allow to dry for a minimum 2-3 hrs. Apply one part of DAMPGUARD mixed chemical and 2 parts of OPC white cement/Birla Putty and make the Putty, apply Putty on the entire surface area. Allow it to dry for at least 3-4 hours. Apply the Final coat of Dr Fixit Dampguard Classic on the entire surface and allow the surface to air cure 48 Hrs proceeds to paint.

M &L mild steel bars conforming to Fe 290 Gde E-165 as in guard bars ,ladder or similar works including welding etc complete all as specified.

Demolition of concrete block masonry built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry (Type C1, 1:3:6, 20mm aggregate) with solid blocks, exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed.

M&L for Shootcreting Average thickness 25-30 mm in RCC columns, beams and slabs etc in layers with approved design mix (minimum cement content of 350 kg/cum on M-25) concrete having the specified minimum characteristics compressive strength (with ordinary Portland cement, coarse and graded stone aggregate of 6 mm maximum size in proportion as per design criteria) or Ready to use Micro concrete mortar including the cost of centering and shuttering at edges and corners etc as directed by Engineer in charge including chipping of unsound/weak concrete material 25mm average thickness from slabs /columns etc with manual chisel or standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc including removal of rust by applying approved rust remover hemical & the coating with Dr fixit Epoxy zinc Primer@6sqm/ltr at DFT of 100 microns as per specification ,applying the SBR Latex based bonding agent on each layer of the shootcreating work of Dr Fixit Pidicrete URP on the entire surface all as per direction.

Providing & fixing hard drawn MS steel wiremesh 80mm x 25mm with 3mm dia wire with Heavy duty nails, Fixing the mesh on the ceiling before shotcreting work. all as per direction.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L Coloured Glazed Ceramic tiles (Digital Designer tiles) 300 x 450 and 6-7mm thick on vertical surfaces such as skirting, dados and risers to steps etc including 10mm thick backing coat in CM 1:4 with all possible design combination as specified by Engr-In-charge complete all as specified and directed

M&L non skid ceramic tiles(Coloured) 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed

M&L non skid ceramic tiles(Coloured) 7 to 8mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed

All as per item above but skirting includig 10 mm thick rendering in CM 1:3 complete all as specified & directed

Dismantling of stone slabs and tiles (Kota stone etc.) of any description or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type) (Jet black) work (table rubbed and polished) in cooking platform, Jambs cill and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including rounding of exposed edges of slab smoothly and polished complete all as specified and directed

M&L Green marble 16-18mm thick as in cills,platforms treads of steps etc over and including cement screed 15mm thick in cement mortar 1:4 laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed. Note: Quoted rate deemed to including the cost of chamfering the exposed edges of marble complete all as specified & directed

M&L Green marble 16-18 mm thick (table rubbed and polished) in riser of steps, jambs, pillars and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 10mm thick plaster 1:3 complete all as specified & directed

Demolition of precast concrete block walling and similar items i.e.. ashlar facing dressed stone work, precast concrete articles etc., of any description and in any position, built in cement mortar, including all quoins, arches and pillars etc. complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) type C-1 (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls/celling etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers i.e.. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 )

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces/stone masonry and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for preparation of old/new wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L for preparation of plastered surfaces of wall and applying 2 coats of Oil Bound distemper over 1.5mm to 2mm thick wall putty finished to a even and smooth finish over a coat of alkali primer complete all as specifed directed

M&L for preparation of the plastered surfaces of ceiling & applying two coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coat synthetic enamel paints on new steel surfaces over a coat of red oxide zinc chrome primer complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified & directed

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors/ paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

Demolition of cement concrete of any description and in any position (reinforced) as in slab, vertical chajjas and the likes etc complete all as specified and directed.

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement complete all as specified and directed.

M&L for complete removal of existing roof treatment incl brushing and applying neat cement slurry with 3 Kg/Sqm of cement complete all as specified and directed.

M&L for averaging 25mm thick PCC of type B-1, 1:2:4 (20mm graded stone aggregate) for padding incl water proofing compund complete all as specified and directed.

M&L Rendering 10 mm thick of CM 1:4 on concrete roof surfaces is to be finished even and smooth without using extra cement with mixing water proofing compound @3% by weight. complete all as directed.

M & L for water proofing treatment to roof slab by applying one coat of bituminous / polymrised primer confirming to IS 3384 @ 0.30 ltr /sqm and laying APP modified membrane pre-fabricated , reinforced with non woven polyester , of 3.00 kg/sqm (minimum) , 3mm thick minimum with minimum 75mm side overlaps and minimum 100mm end overlaps complete all as specifiedand directed.

M&L cleaning surface and applying two coats of aluminium paint on roof or vertical surfaces complete all as specified and directed.

Taking down chowkat or frames n.exc 1.5 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed.

Taking down chowkat or frames exc 1.5 sqm & n exc 4 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed.

Taking down shutters of any description and in any position exceeding 1 sqm & not exceeding 2 sqm each complete all as specified and directed.

S & F Powder coated Aluminium alloy sections sliding windows with frames Series-C (20mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 5mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed.

M & L powder coatedaluminium deco grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with aluminium frame of size 9x9x1 mm complete all as specified and directed.

S&F powder coated aluminium anodised ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded Single Side Prelam PVC sheet used instead of Plain colour PVC sheet and stile & rails having one side feathered edge and on other side 10mm 90 degree bent edge PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of prelam colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required complete all as specid & directed

S&F solid PVC door frame of size 50mmX47mm made out of 5mm one side prelam colour PVC sheet reinforced with MS square tube all as per specifications and as per drawing complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters , solid core construction , with block board core and plywood face panels commenrcial face on bath sides with lipping/frame to match complete all as specified and directed.

M & L for 30 mm thick glazed and skeleton shutters of 2nd class Hard Wood(Not less than Hollock wood) local made shutter, open rebated and prepare to revive glass, gauge etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.24 (a) supplied and fitted to chowkat complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L preparation of the new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 100 mm long butt hinges stainless steel medium weight and fixed to wooden or PVC frame fixed in repairs by stainless steel screw as directed

S&F aluminium handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed.

S&F butt hinges 100mm long medium weight, cold rolled mild steel complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Supply and fixing in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia as per sample approved by GE complete all as specified & directed.

Supply and fixing of purpose made brackets trade pattern for decorative type curtain rods suitable for holding 22 to 25 mm dia as per sample approved by GE complete all as specified & directed

Supply and fixing in repair of decorative fincals (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for 22 to 25 mm dia curtain rods as per sample approved by GE's complete all as specified & directed

Dismantling water tanks of any description and in any position , of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

S&F 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl fixing arrangment for inlet/outlet/overflow & vent pipe of standard size complete all as specified & directed

S&F Ball brass valves , high pressure , with polythene float and fly nut complete & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed complete all as specified and directed.

S&F Vitreous China, wash down water closet pan "Pedestal pattern" white including connection to drain and to flush pipe and anti syphonic pipe including all joints and making good the disturbed surfaces complete all as specified.

S&F in Repairs PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle, flush pipe of polyethylene pvc 32mm dia high or low density including brackets complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified

S & F in repair vitreous china wash basin pedestal type , white flat back , size 550mmx450mm with and including pedestal, Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including bracket , CP waste coupling & flexible waste pipe complete all as specified and directed .

S&F in repair for shower rose brass chromium plated without swivel joints, 125 mm in size including fixing to steel pipe complete all as specified and directed.

S&F in repair Bib taps , cast copper alloy screwed down high pressure with crutch or butter fly handle fancy type long body CP for 15mm dia bore GI Pipe or for brass ferrule and fixed complete all as specified

S&F in repair Stop valves, fancy type chromium plated ISI marked , cast copper alloy, screwed down high pressure for 15 mm bore dia GI tubing pipe, high pressure, with crutch butter fly handle complete all as specified

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia complete all as specified & directed

S&F pillar taps in repair of cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with long swan shanks and fly nuts screwed for iron pipe, 15mm bore fancy type complete all as specified and directed.

S&F stainless steel health faucet witrh 1 Mtr tube and hoock complete all as specified and directed by Engr-in-charge. Confirming to Cat part No ALD573 of jaguar/PRAYAG completed all as specified

Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) ,of any description and in any position, including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories)complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed

S&F in repair PVC (SWR) floor trap 75 mm bore, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed

S&F PVC (SWR) Junction, single, (single T) equal or unequal with access door, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) Junction, single, (single T) equal or unequal with access door, 75 mm bore, complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed.

S&F (concealed / open) 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 20mm bore complete all as specified and directed.

S&F (concealed / open) 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 25mm bore complete all as specified and directed.

S&F (concealed / open) 40mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting including taking down existing GI tubing 40mm bore complete all as specified and directed.

S&F in repair stainless steel grating 150 x150mm size over floor trap anti cockroach all as approved sample all as specified and directed

S&F in repair of PVC cabinet size 650 x 400mm, comprising of looking glass, space for bath soap, shampoo, tooth brush and paste, handle towel rail complete allas specified and as approved of any fo following makes :- HINDWARE / CERA / NEYCER / PARRYWARE/CLASSIC complete all as specified and directed.

S & F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden /plastic cleats(Minimum weight 190gms) complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade S-304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed Fe 410-W (Gde- E- 250) quality- A complete all as specified & directed

S& F Mild steel, plain, black sheet in hearths; covering to door shutters; covering to door chowkats (frames); cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as requireds required complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in as in sub base all as specified and directed.

M&L for providing prrecast cement concrete Type B1 1:2:4 (20 mm graded aggregate) in appex stone/kerb stone with plain fair faces including chamfers, weathering throting etc and set in cement mortar 1:4 complete with joints to math size and shape as approved complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying if inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed

M&L for Plain cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in coping including necessary form work complete all as specified & directed

S&F 18 mm thick prelaminated PVC Cheluka ply prelaminated one side with decorative choice lamination and other side plain fixed with screws to PVC celuka ply works all as directed and as per manufacture instructions Make : Rajshree plasticwood

All as per Above item no 180 but 12 mm thick plain cheluka plywood complete all as specified and directed.

S&F brass Handle fabricated type polished of Size 100 mm complete all as specified and directed.

Dismantaling and taking down copper / aluminium point wiring any type / size complete with removing all connection and accessories such as switches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface complete all as specified and directed.

Taking down old and unserviceable sub main wiring any size / type / core incl earth wire complete with batten/conduit etc and making good the disturbed surface to match the existing disturbed surface all as directed

Taking down old and unsrevicable sheet metal enclosure , switch fuse unit , distribution bord any type /way / capacity including fuses,MCB's , insulator etc complete after removing all connection and making good the disturbed surface all as directed

M&L for Point wiring complete with FR PVC insulated unsheathed , 1100 V grade conforming to IS 694 , 1.5 Sqmm (Norminal area) multistranded ,copper conductor cable drawn through in non metallic rigid PVC conceled/surface conduit medium grade ,minimum 20 mm dia, ISI Marked, with sutaible size of 1 to 8 module metal flush boxes and back plate for mounting of modular switches/socket and regulators and including modular fornt plate with all acessories complete all as specified and directed.

One light point controlled by one way one switch SP 5 Amps ,240 V.

One light point controlled by two 2 way switch SP 5 Amps ,240 V.

One ceiling/exhaust fan point controlled by one way one switch SP 5 Amps, 240 V.

One switch socket outlet 3 Pin, 5 Amps, SP on independent board

One switch socket outlet 3 Pin, 5 Amps, SP on same board.

One bell / buzer point controlled by one push button switches on independent board .

All as per the above item No 186 herein before but with 2.5 Sqmm cable for 3 Pin 5/15 Amps switch socket outlet complete all as specified and directed.

S&F modular switch one way 6 Amps , 1 module type complete all as specified and directed.

S&F modular switch two way 6 Amps , 1 module type complete all as specified and directed.

S& f modular socket , 6 Amps , 2/3 pin combined 2 module complete all as specified and directed.

S& f modular switch socket combination, 6 Amps / 16 Amps , 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked complete all as specified and directed.

S&F Bell push 6 Amps 1 module complete all as specified and directed.

S&F bell Multi music type , 240 Volt , Single Pole ISI marked complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting upto PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit including as per site requirement and 2 Nos of round or square PVC bolck for fixing of FTL fitting complete all as per directed

Supply & fixing modular fan regulator step type , 1/2 module complete all as specified and directed.

M&L for sub main wiring with two runs of 6 Sqmm (2x6 sqmm )1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductorcable confirming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories concealed in walls/roofs/floors etc with one run of 6 Sqmm (1x6 sqmm ) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire complete all as specified and directed. Note:- 2 runs of 6 Sqmm ,one run of 6 Sqmm ( 2x6 sqmm + 1x6 sqmm ) cable and one meter of conduit will be measured as one unit again.

S&F sheet metal enclosures for distribution board when MCB to be used SPN ( Single pole and neutral ) 8 way, 240 Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed.

S&F in MCB TPN, 63 Amps,415 Volts, rupturing capacity 10 KA."C" Series complete all as specified and directed.

S&F sheet metal enclosures for distribution board when MCB to be used TPN ( Triplepole and neutral ) 4 way, 415Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed.

S&F MCB SPN,40 Amps, 240 Volts, rupturing capacity 10 KA."C" Series complete all as specified and directed.

S&F MCB SP, 5 to 32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series complete all as specified and directed.

M&L , earthing complete for machinary / Equipment installed at power house / sub station with galavanised steel earth plate electrode of size 60 cmx 60 cmx 6 mm thick buried directly in ground ( earth pit not less then 2.25 m deep below the normal ground level ) with top edge of the earth plate not less then 1.5m below normal Ground level connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washerws and check nuts all shown in electrical plate No.5 of SSR Part- I connected to main board / disribution board complete .Earthing GI lead and GI protection pipe 15 mm dia light grade upto 7.5 m from earth pit connecting to machinary/ equipment, testing point, all as specified and testing on completion all as per directed. Note :- (i) The unit rate shall also included for earth work in hard /dense soil , PCC type C-I (1:3:6) chamber , PCC 1:2:4 type B-I cover 50 mm thick reinforced with 8 mm dia TMT bars,150 mm c/c both ways, funnel with watering pipe 20 mm dia medium graded , GI protection pipe light grade 15 mm dia and wire mesh complete in addition to items No. 1(a) to (e) of preamble (notes) under sub heading earthing specified on SI page No. 389 of SSR Part - II. (ii) Earthing lead and GI protection pipe beyond 7.5 mtrs will be measured and paid separatelly if required under appropriate Schedule. Note :- (i) Earthing shall be tested as specified in casul 19.137 of SSP PART - I 2009 , to the entire satisfication of Engr-in-Charge. (ii) On teting after complataion of earthing , if the desired earth resistance is not obatined the earthing wiil be re done by the contractor at his on risk and cost to the entire satisfaction of the Engr - in - charge.

Supply and fix in replacement XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of cross sectional area 25 sqmm 4 core complete all as specified and directed

Excavation in trenches in soft/loose soil , not.exc 1.5 mtr wide and not.exc 1.5 mtr deep and getting out in soft/loose soil for laying of cable/foundation of pole and stay etc in complete as sepecified.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

Removing excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above ground level from starting point complete all as specified and directed.

M&L for sand cushioning in trenches for protection of LT under ground cable including watering and consolidation complete all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover class LV Type 1, flat, size 250mm x 150mm x 40mm complete. Complete all as specified and directed.

Supply and laying GI tube light grade 50 mm bore complete. Complete all as specified and directed.

Supply and lay pipe uPVC pipe including fittings of size 50 mm (2.0") dia complete all as specified and directed.

Supply and lay pipe uPVC pipe including fittings of size 25 mm (1.0") dia complete all as specified and directed.

supply and fix ball valve 25 mm dia including all fittings all as specfied and directed

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete,complete all as specified and directed.

Supply and fixing electric water heater, storage type steel body with inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers All as specified and Directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep copper 100% aluminium blades thickess 1.00mm min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

S&f angle holder backlite with 1x11 Watt CFL with fixed on hylum sheet including all fixing acessories and making of connection with twin core flexible copper conductor from ceiling rose to fitting complete all as specified and directed.

Supply and lay pipe uPVC pipe including fittings of size 50 mm (2.0") dia complete all as specified and directed.

Supply and lay pipe uPVC pipe including fittings of size 25 mm (1.0") dia complete all as specified and directed.

supply and fix ball valve 25 mm dia including all fittings all as specfied and directed

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and as directed

Grouting, injecting two part, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and as directed by Engineer-in-charge. Note :- Mode of measurement: per kg of material consumed Make: Sika - SikaDur 52 LP/ Fosroc- Conbextra EP 10/ Pidilite Dr Fixit Epoxy Injec

Material and labour for Chipping of slab/columns/ beams/ chajjas/parapet/roof projection/balcony/staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts, complete all as specified and directed

Material and labour for Cleaning & applying rust remover in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with Sika friazinc R or equivalent to reinforcement surface as per manufacturer’s instructions including all scaffolding, machinery, tools tackles and clearing of debris complete all as specified and as directed.

S & F of new steel or rebar’s by drilling holes with 10 mm to 20mm dia and 100 to 200mm deep as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinyl ester resin anchor or two components, styrene & cement free epoxy acrylate fixing and anchoring compound (having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching complete all as specified and as directed. (Note : Steel/reinforcement shall be paid and measured separately).

NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.

M/S S. SINGH TRADERS (BID ID -3481576)

Sanjay Enterprise (BID ID -3489857)