Raising and upgradation of existing low laying Cement Concrete (CC) Roads and culverts to cross roads at beside Ramalayam in Sundraiah Nagar 63rd Division

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and back filling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH. by manual means

Conveyance of excavated earth with an average lead of 2 Km including loading, unloading, spreading and stocking etc. complete

Labour Engaged on hire basis for Removing silt of side drain including all labour charges etc., complete.

Bailing of water with oil Engine including conveyance of Oil Engine to work site, including fuel and operational charges and wages for driver / Helper etc., complete as per specification.

Providing concrete for plain concrete (M10) using 220 Kgs Cement ,40 mm nominal size hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH

PCC vertical walls of plane surface (rate is for both sides centering) including open drains of 600mm size and above.

Providing concrete for plain concrete (M15 Design Mix) using 275 Kgs Cement ,20 mm,10mm nominal size Graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH

Supply and placing of the RCC M30 (Design Mix) concrete corresponding to IS 456 using weigh batcher / mixer 20mm,10mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry, Cement 407 Kgs including cost and conveyance of all materials like cement, fine aggrregate (sand) coarse aggregate, water etc., to site and all labour charges such as machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work.

Supplying, fitting and placing HYSD bar reinforcement as per drqwings and technical specifications clauses 1000 and 1202 MORD & 1100, 1600 MORTH for bars below 36mm dia including over laps and wastage, where they are not welded including cost and conveyance of binding wire and preparation and tying grills and fixing in position and labour charges etc., complete

Manufacturing, Supply, Delivery and fixing of M.S. Iron Gate , MS Grill using with M.S. Angulars, M.S. flats including cost and conveyance of all materials and labour charges for cutting, welding, grinding and fixing etc., , complete.as directed by the departmental authorities.

Supply and delivery of quarry dust from approved quarry including cost and conveyance of all materials and labour charges for stacking at site to departmental guage, spreading, sectioning, seignorage, watering etc., complete as per specification.

Providing concrete for plain concrete (M20 Nominal mix) using 330 Kgs Cement 20 mm,10mm nominal size Graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202 MORD / MORTH Cement Concrete

Separation Membrane of impermeable plastic sheeting 125 micron thick

Brick Masonry in CM(1:5) with Bricks traditional size 23x11x7 cms 2nd class including cost and conveyance of all materials and labour charges for mixing of mortor watering curing etc. complete.

Plastering in CM (1:4) 12mm thick including cost and conveyance of all materials and labour charges for mixing of mortor watering curing etc

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 MORD. Unit = cum. including cost and conveyance of all materials and labour charges etc,Complete.

Supply of 25mm thick high performance expansion joint filler board (SILFLEXCAPCELLHD-100 or equivalent make),placing the same 25mm below top of pavement slab sealing with bituminous hot sealing compound (Grade-A-ISI) polysulphudiet 50mm interval in CC.Pavement incl.cost and conveyance of all materials but excl.labour charges for placing in position,for expansion joints confirmig to MORTH Specification 602-1Rmt of joint length.For 175mm thick CC roads (150mm Joint)

Supply of bituminous hot sealing compound (grade-A ISI ) poly sulphide and sealing the joints incl.cost and conveyance of all materials etc.but excl.labour charges for placing in position for contraction joints at 1.50 interval / for expansion joints/for longitudinal joints as per MORTH specification number 602-1 Rm