REPAIR MAINT OF DIFFERENT TYPE CAPACITY OF CENTRIFUGAL SUBMERSIBLE MONOBLOCK PUMP SETS INCLUDING BOREWELLS AND ALLIED WORKS AT AF STN NALIYA

Material and labour for repair & overhauling of 70/75 HP electrical induction motor, 3 phase, 415 volts including disconnecting all electrical connections, decoupling from pump, taking down the motor from foundation, cleaning and varnishing the stater & rotor winding, heating and drying, replacement of burnt terminals, greasing to bearings, re-assembling the motor and refixing of motor on the foundation by using new nut, bolts and washers, coupling with pump,checking alignment connecting all electrical connections, checking the vibrations, RPM, DOR, testing on full load complete all as specified and directed.

All as per serial item numer 1.00 here-in-before but of capcity 60 HP, 3 Phase

All as per serial item numer 1.00 here-in-before but of capcity 15HP-20 HP, 3 Phase

Material and labour in repairs for rewinding of 70/75 HP, 3 Phase capacity induction motor by means of cutting and removing existing burnt out winding completely cleaning and repair of slots and rewinding with new copper wire of existing gauge and size / turns, varnishing with class 'B' insulation, balancing of shaft, incl replacement of UNSV connection plate / terminal point as per site requirement, assembling the motor including transportation, testing as per the specified RPM at workshop complete all as specified and as directed.

All as per serial item numer 4.00 here-in-before but of capcity 60 HP, 3 Phase

All as per serial item numer 4.00 here-in-before but of capcity 15 to 20 HP, 3 Phase

Material and labour for repair & overhauling of 70/75 HP, 3 Phase capacity centrifugal pump set of any make, dismantling and taking down pump after disconnecting water supply connections, decoupling from motor removing out impeller, cleaning, descaling , greasing to bearings and replacement of unserviceable parts such as bearings, pump shaft sleeves, coupling pully, pump shaft etc. Assembly in the pump with new packing materials, nuts, bolts & washers , gland bolt & packing,coupling bushes, coupling bolts and coupling with motor checking for vibration & alignment connecting delivery and suction pipe, testing the pump sets complete all as specified and directed. Note :- Spare parts shall be measured and paid separately

All as per serial item numer 7.00 here-in-before but of capcity 60 HP, 3 Phase

All as per serial item numer 7.00 here-in-before but of capcity 15 to 20 HP, 3 Phase

Supply and fix in repair following parts for existing centrifugal pump set electric driven 3 phase 415 volt 75/70 HP complete all as specified and directed.

Motor bearing. Make : SKF/NBC/TATA/FAG/ UBC.

Motor cooling fan

Pump motor Pin bush coupling of size RB 198/10 with nut bolts, washer

L-225/190 spider.

Cover bolts & washers

Pump bearing with housing, O'ring. Make : SKF/UBC/TATA/FAG/ NBC

CI impellar as per existing model complete

SS Sleeve (Gland Sleeve)

Pump SS shaft with studs and nuts for pump body.

Shaft seal of existing size

Supply and fix in repair following parts for existing centrifugal pump set electric driven 3 phase 415 volt 60 HP complete all as specified and directed :-

Motor bearing. Make : SKF/NBC/TATA/FAG/ UBC.

Motor cooling fan

Rubber bushes for coupling as per existing model and size

Pump motor Pin bush coupling of size RB 198/10 with nut bolts, washer

Cover bolts & washers

Pump bearing with housing, O'ring. Make : SKF/UBC/TATA/FAG/ NBC

CI impellar as per existing model complete

Gland packing

SS Sleeve (Gland Sleeve)

SS Pump shaft with studs and nuts for pump body.

Shaft seal of existing size

Supply and fix in repair following parts for existing centrifugal pump set electric driven 3 phase 415 volt 15 to 20 HP complete all as specified and directed:-

Motor bearing. Make : SKF/NBC/TATA/FAG/ UBC.

Motor cooling fan

Cover bolts & washers

CI impellar as per existing model complete

SS Pump shaft with studs and nuts for pump body.

Shaft seal of existing size

All as per serial item numer 13.00 here-in-before but of capcity 0.5 to 3 HP, 1 Phase

Supply only greasing for bearing of centrifugal Pumps all as specified and as directed.

Material and labour in repairs for rewinding of 2 to 7.5 HP , 3 Phase capacity monoblock pump set by means of cutting and removing existing burnt out winding completely cleaning and repair of slots and rewinding with new copper wire of existing gauge and size / turns, varnishing with class 'B' insulation, balancing of shaft, incl replacement of UNSV connection plate / terminal point as per site requirement, assembling the motor including transporation, testing as per the specified RPM at workshop complete all as specified and directed.

All as per serial item numer 16.00 here-in-before but of capcity 0.5 to 3 HP, 1 Phase

Supply and fix in repair following parts for existing monoblock pump set electric driven 3 phase 415 volt 2 to 7.5 HP complete all as specified and directed.

Motor bearing with housing . Make : SKF/NBC/TATA/FAG/ UBC.

Motor cooling fan

Cover bolts & washers

CI impellar as per existing model complete

SS Sleeve (Gland Sleeve)

SS Pump shaft with studs and nuts for pump body.

Shaft seal of existing size

Supply and fix in repair following parts for existing monoblock pump set electric driven 1 phase 230 volt 0.5 HP to 3 HP complete all as specified and directed:-

Motor bearing with housing . Make : SKF/NBC/TATA/FAG/ UBC.

Motor cooling fan

Cover bolts & washers

CI impellar as per existing model complete

SS Sleeve (Gland Sleeve)

Pump shaft with studs and nuts for pump body.

Shaft seal/water seal of existing size

Capacitor of capacity 40 to 100 MFD

Capacitor of capacity 120 to 250 MFD

All as per serial item numer 20.00 here-in-before but of capacity 7.5 HP to 15 HP, 3 Phase

Material and labour for complete opening of submersible bore well pump motor set of 30 HP to 40 HP capacity for repair / replacement of unserviceable worn out bearing / worn out unserviceable shaft / burned out copper winding as per existing gauge, No of turns, varnishing with specified RPM / worn out strainer / bush / sleeve / thrust pad / thrust bearing / thrust bearing lock nut etc, including re-assembling and testing as per specified RPM at workshop etc complete all as specified and as directed. Note :- (i) The quoted shall be inclusive of transportation of pump set from pump house site to workshop and back to pump house site after necessary repairs. (ii) The quoted shall be inclusive of balancing of shaft through lathe work incl welding wk if any required as per site requirement, balancing of starter, repairing starter stamping, water cap, SS nut, bolts, washers etc complete. (iii) The quoted shall be inclusive of shaft rubber seal etc complete (iv) Winding shall be measured and paid separately. (v) Spares replaced shall be measured and paid separetely under relevant item.

All as per serial item numer 22.00 here-in-before but of capcity 7.5 to 15 HP, 3 Phase

Material and labour for rewinding the submersible motor of 30HP to 40 HP capacity by means of cutting and removing existing burnt out winding completely cleaning and repair of slots and rewinding with new PVC insulated copper wire of existing gauge and size / turns, balancing of shaft, testing as per the specified RPM at workshop complete all as specified and as directed.

All as per serial item numer 24.00 here-in-before but of capcity 7.5 to 15 HP, 3 Phase

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt 30 to 40 HP complete all as specified and directed:-

Thrust bearing incl bush

Revolving Disc

SS Connection piece

CI upper housing

CI Lower housing

CI Motor Base

Thrust plate

CI Suction chamber

CI stage bowl

GM bush for pump

SS Impeller

CI DOL Piece

Bearing housing

Sand guard/cover

Pump shaft sleeve of SS

PVC Neck Ring of existing model

T Bolts of existing size and model

Pump shaft lathe work including turning, straightening etc complete

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt, 7.5 HP to 15 HP complete all as specified and directed :-

Thrust bearing incl bush

Revolving Disc

SS Connection piece

CI upper housing

CI Lower housing

CI Motor Base

Thrust plate

CI Suction chamber

CI stage bowl

GM bush

GM Impeller

CI DOL Piece

Bearing housing

Sand guard/cover

Pump shaft sleeve of SS

PVC Neck Ring of existing model

T Bolts of existing size and model

All as per serial item number 28.00 here-in-before but of capcity 20 to 30 HP, 3 Phase

All as per serial item number 28.00 here-in-before but of capcity 10 to 15 HP, 3 Phase

All as per serial item number 28.00 here-in-before but of capcity 3 to 7.5 HP, 3 Phase

All as per serial item number 28.00 here-in-before but of capcity 0.5 to 2 HP, 1 Phase

Material and labour for complete opening of horizontal submersible motor 40 HP to 50 HP for repair /replacement of unserviceable worn out bearing/worn out unserviceable shaft/burned out copper winding /worn out strainer/bush/sleeve/thrust pad/thrust bearing/thrust bearing lock nut etc including transportation complete all as specified and directed. Note :- (i) The quoted shall be inclusive of transportation of pump set from pump house site to workshop and back to pump house site after necessary repairs. (ii) The quoted shall be inclusive of balancing of shaft through lathe work incl welding wk if any required as per requirement, replacement of pump seal, replacement of wornout nut, bolts, washers etc complete. (iii) Winding shall be measured and paid separately.

All as per serial item number 33.00 here-in-before but of capcity 20 to 30 HP, 3 Phase

All as per serial item number 33.00 here-in-before but of capcity 10 to 15 HP, 3 Phase

All as per serial item number 33.00 here-in-before but of capcity 3 to 7.5 HP, 3 Phase

All as per serial item number 33.00 here-in-before but of capcity 0.5 HP to 2 HP, 1 Phase

Material and labour for rewinding the submersible motor of 40HP to 50 HP capacity by means of cutting and removing existing burnt out winding completely cleaning and repair of slots and rewinding with new PVC insulated copper wire of existing gauge and size / turns, balancing of shaft, testing as per the specified RPM at workshop complete all as specified and directed.

All as per serial item number 38.00 here-in-before but of capcity 20 to 30 HP, 3 Phase

All as per serial item number 38.00 here-in-before but of capcity 10 to 15 HP, 3 Phase

All as per serial item number 38.00 here-in-before but of capcity 3 to 7.5 HP, 3 Phase

All as per serial item number 38.00 here-in-before but of capcity 0.5 to 2 HP, 1 Phase

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt 40 HP to 50 HP complete all as specified and directed :-

Pump Thurst bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

Thrust plate

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt 20 HP to 30 HP complete all as specified and directed:-

Pump Thrust bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

Thrust plate

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt 10HP to 15 HP complete all as specified and directed :-

Pump Thrust bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

Thrust plate

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt 5 HP to 7.5 HP complete all as specified and directed:-

Pump bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

Thrust plate

Supply and fix in repair following parts for existing submersible pump set electric driven 1 phase 230 volt 0.5 HP to 2 HP complete all as specified and directed:-

Pump bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

All as per serial item number 48.00 here-in-before but of capcity 3 to 5 HP

Material and labour for complete opening of non-clog pump motor 10 HP to 15 HP for repair /replacement of unserviceable worn out bearing/worn out unserviceable shaft/burned out copper winding /worn out strainer/bush/sleeve/thrust pad/thrust bearing/thrust bearing lock nut etc including transportation complete all as specified and as directed. Note :- (i) The quoted shall be inclusive of transportation of pump set from pump house site to workshop and back to pump house site after necessary repairs. (ii) The quoted shall be inclusive of balancing of shaft through lathe work incl welding wk if any required as per requirement, replacement of wornout nut, bolts, washers etc complete. (iii) Winding shall be measured and paid separately.

All as per serial item number 50.00 here-in-before but of capcity 3 to 5 HP

Material and labour for rewinding the non-clog motor of 10HP to 15 HP capacity by means of cutting and removing existing burnt out winding completely cleaning and repair of slots and rewinding with new PVC insulated copper wire of existing gauge and size / turns, balancing of shaft, testing as per the specified RPM at workshop complete including replacement winding oil and oil seal complete all as specified and as directed.

All as per serial item number 52.00 here-in-before but of capcity 3 to 5 HP

Supply and fix in repair following parts for existing nonclog pump set electric driven 3 phase 415 volt 10 HP to 15 HP complete all as specified and directed.

Pump bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

Supply and fix in repair following parts for existing submersible pump set electric driven 3 phase 415 volt 3 HP to 5 HP complete all as specified and directed:-

Pump bearing Make : SKF/NBC/TATA/FAG/ UBC.

Pump bush

SS sleeve

CI impellar as per existing model

Pump shaft

Shaft seal of existing size

Supply and fix in repairs PVC insulated 3 core 4 Sqmm copper multistranded PVC sheathed flexible cable suitable for Non clog motor ISI marked and conforming to IS : 694 and connecting to submersible pump with water proof jointing kit and to LT panel with lugs after taking out old unserviceable cable complete all as specified and as directed.

Supply and fix in repairs PVC insulated 3 core 10 Sqmm copper multistranded PVC sheathed submersible flexible cable ISI marked and conforming to IS : 694 and connecting to submersible pump with water proof jointing kit and to LT panel with lugs after taking out old unserviceable cable complete all as specified and as directed.

All as per serial item number 57.00 here-in-before but 3 core 16 Sqmm

All as per serial item number 60.00 here-in-before but 150 mm bore

Supply and fix in repair MCCB 3 pole , 415 volts , fixed thermal and fixed magnetic setting 63 Amps to 100 Amps with braking capacity 16 KA, Ics=100% Icu, complete including replacement of u/s lugs, spreader connector complete all as specified and directed.

All as per serial item number 62.00 here-in-before but 125 Amps , with breaking capacity 16 KA.

Supply and fix in repair MCCB 4 pole , 415 volts , fixed thermal and fixed magnetic setting upto 160 Amps with braking capacity 16 KA Ics=100% Icu, complete including replacement of u/s lugs, spreader connector complete all as specified and as directed.

All as per serial item number 64.00 here-in-before but 200 Amps , with braking capacity 35 KA.

All as per serial item number 64.00 here-in-before but 250 Amps , with braking capacity 35 KA.

All as per serial item number 64.00 here-in-before but 400 Amps , with braking capacity 35 KA.

Supply and fix in replacement of start push button of Green colour as per site requirement all etc complete all as specified and directed.

Supply and fix in replacement of stop push button of Red colour as per site requirement all etc complete all as specified and directed.

Supply and fix in replacement of motor ON indiating light of green colour as per site requirement all etc complete all as specified and directed.

Supply and fix in replacement of motor Trip indiating light of yellow colour as per site requirement all etc complete all as specified and directed.

Supply and fix in replacement of neon LED light of Red/Yellow/Blue colour as per site requirement all etc complete all as specified and directed.

Supply and fix in repairs Power contactor FP AC-1 duty with 240 VAC Coil of capacity 400 Amps (MCX 43) with add-on aux contacts 2 NO+2 NC -01 Nos incl with all necessary internal electrical connections and taking out unserviceable all etc complete all as specified and directed.

Supply and fix in repairs Power contactor FP AC-1 duty with 240 VAC Coil of capacity 325 Amps (MCX 41) with add-on Aux contact 2 NO+2 NC -01 Nos incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs Power contactor FP AC-1 duty with 240 VAC Coil of capacity 16 Amps (MCX 01) incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs Power contactor TP AC-3 duty with 240 VAC Coil of capacity 160 Amps (MNX 140) with add-on blocks 1 NO+1 NC -02 Nos incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs Power contactor TP AC-3 duty with 240 VAC Coil of capacity 100 Amps (MNX 70) incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs Power contactor TP AC-3 duty with 240 VAC Coil of capacity 22 Amps (MNX 22) with add-on blocks 1NO/1 NC -01 Nos incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs Power contactor TP AC-3 duty with 240 VAC Coil of capacity 12 Amps (MNX 12) with add-on blocks 1NO/1 NC -01 Nos incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs auxiliary contact block MNX A2,1 No 1 NC incl with all necessary internal electrical connections and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs add-on auxiliary contact block 1 NO + 1 NC suitable for MNX / MCX type contactors including necssary internal electrical connections all etc complete as specified and directed.

Supply and fix in repairs thermal overload relay of capacity 135-225 Amps (MN-12)with all necessary internal electrical connection and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs thermal overload relay of capacity 60-100 (MN-12) Amps with all necessary internal electrical connection and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs thermal overload relay of capacity 45-75 (MN-5) Amps with all necessary internal electrical connection and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs thermal overload relay of capacity 4.5-7.5 (MN-2) Amps with all necessary internal electrical connection and taking out unserviceable all etc complete as specified and directed.

Supply and fix in repairs repairs Single Phasing Preventer Relay type VSP-II, 415V including necessary internal electric connection with size copper wire complete all as specified and directed.

Supply and fix in repairs electronic timer for star-delta time delay 30 to 120/3 to 30 seconds all as per existing sample complete including internal electric connection with suitable size copper wire all as specified and as directed.

Supply and fix in repair ammeter 415 volt, 3 phase digital type including necessary internal electric connection with suitable size copper wire & modification required for fitment as per site requirement complete all as specified and as directed.

Supply and fix in repair voltmeter 415 volt,3 phase 0 to 500 volts rating, analog type including necessary internal electric connection with suitable size copper wire & modification required for fitment as per site requirement complete all as specified and as directed.

Supply and fixing in repairs 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole and 6 Amps to 32 Amps current carrying capacity in the MCB DB/LT starter panel complete with connection testing and commissioning.

Supply and fixing in repairs 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN and 16 Amps to 32 Amps current carrying capacity in the DB/LT starter panel complete with connection testing and commissioning complete all as specified and directed.

Supply and fix in repairs DOL starter in sheet metal enclosure max motor output at 415 Volt, 3 phase, 7.5KW, relay range 9-15 Amps complete all as specified and as directed.

Supply and fixing in replacement of terminal strip 6 way all etc complete including electrical connection all as specified complete all as specified and as directed.

Supply and fixing in replacement of terminal strip 3 way all etc complete including electrical connection all as specified complete all as specified and as directed.

Material and labour for preparation of old painted surfaces of centrifugal pump set of 70/75 HP capacity and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

All as per serial item number 96.00 here-in-before but of capacity 60 HP

All as per serial item number 96.00 here-in-before but of capacity 20/15 HP

All as per serial item number 96.00 here-in-before but of capacity 5/3/2 HP

Material and labour in repairs for construction of valve pit chamber in PCC (1: 5 : 10) masonry built in CM (1 :4) with 3.00 thick and locking arrangement including excavation and earth works , PCC (1:4:8) type D2 for foundation PCC bed , coping in cement concrete (1:2:4) type B1, plastering 15 mm thick in CM (1:4) , MS door with painting with one coat of bituminous black paint on all steel surface for size of chamber 1000 mm x 1000mm x 1200 mm including demolition of unserviceable damaged existing pit complete all as specified and as directed.

Supply and fix in replacement of nylon rope of any size as per site requirement including taking out old unserviceable all etc complete as specified and directed.

Material and labour in repairs for Earthing complete with copper earth plate electrode 60×60cm ×3.15mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to copper earth strip of 20x3.15mm (upto 7.5m in length from earth plate) by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 including charcoal, rock salt, necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40mm thick cover with MS bar 8mm dia 150mm c/c reinforcement, watering funnel, 32mm dia light grade for protection of earth electrode, 20mm dia for watering complete all as specified and directed and tested on completion.

Material and labour in repairs for Earthing complete with galvanised earth plate electrode 60×60cm ×6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to GI earth strip of 32x6mm (upto 7.5m in length from earth plate) by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 including charcoal, rock salt, necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40mm thick cover with MS bar 8mm dia 150mm c/c reinforcement, watering funnel, 40mm dia light grade for protection of earth electrode, 20mm dia for watering complete all as specified and directed and tested on completion.

Material and labour for repairs of Mild Steel Structure with framed work such grills, gratings etc with ends of bars shouldered and/or rivetted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work, portions framed and hung gates, including pintle hinges, stops, hand made sliding bolts etc as conforming to Fe290, Gde E-165 including two coats of paints of approved colour and including one coat of red oxide primer complete all as specified and directed.

Material and labour for in repairs of Precast cement concrete block (1:3:6), type B1 (uising 20mm graded aggregate) exceeding 10 cm in width and setting in mortar 1:6 complete all as specified and directed.

Material and labour for 15mm thick rendering in CM 1:4 on block masonry surface even and smooth without using extra cement mortar all as specified and directed.

Material and labour for Precast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) including necessary form work finishing even and smooth without using extra cement complete all as specified and directed.

Material and labour for removing existing PCC foundation after taking out pump motor of capacity 60 HP /70 HP from base frame, disconnecting suction, delivery lines and providing new PCC foundation and MS base plate of existing type, size and thickness including foundation bolts all etc complete all as specified and directed:

All as per serial item number 109.00 here-in-before but of capacity 15 HP monoblock pumpset

Material and labour for installation of pumpset of capacity 60/70 HP on New PCC foundation and fixing with new bolts and nuts for base plate, fabricating to suction, delivery and priming line and connecting with existing lines, connecting power supply and testing, commissioning of pump set complete all as specified and directed

All as per serial item number 111.00 here-in-before but of capacity 15 HP monoblock pumpset.

Supply and fix in repairs of delivery HDPE hose pipe of size 65/50mm dia and length 30 mtrs with new SS connectors nut bolts, nylon rope of length 5 mtrs by lifting of submersible mud pump of capacity 5 / 7.5 HP from SWT/open well by disconnecting electrical connection and lowering of pump set duly connecting the new hose HDPE pipe and electrical connections, testing on completion all etc complete as specified and directed.

Please Enable Macros to View BoQ information