Providing 160mm dia HDPE pipe from Gottipati Brahmaiah to Velagapudi Vari Veedhi and 110 mm HDPE pipe in Dhanekula vari street (12/50/120-12/50/123) 12th Division Work Division - III. 1st Call General Funds

Earth work in excavated for structures as per drawing and technical specifications clause 305.1 including setting out construction of shoring and brcking, removal of stumps and other deleterious material and disposal upto a lead of 50mts dressing of sides and bottem and backfilling intrenchs with excavated suitable material as per technical specification 305 MORD/304 MORTH

Engaging of Air Compressor 7Cm on hire basis including cost and conveyance of all materials and labour charges wages of driver and helper and fuel charges ctc.complete

Cutting of C.C. surface including stacking of excavated materials for lying of pipe lines as per the ditections of the departmental authorities.

Supply and delivery of Quarry Dust filling from approved source including cost, seignorge charges and conveyance of all materials including all labour charges for filling, sectioning, watering and ramming etc., complete as per S.S

Bailing out of water from Pipe line trenches with oil driven pump sets, including hire charges, fuel charges for driver & helper etc complete

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P, excluding all taxes (Supply up to 90 mm dia. in coil & above 90 mm dia. straight length.) For 160mm dia

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P, excluding all taxes (Supply up to 90 mm dia. in coil & above 90 mm dia. straight length.) For 110mm dia

Lowering, laying, jointing & testing of HDPE Pipes by butt fusion welding as per IS 7634-part-II/1975 as ammended from time to time to the alignment and gradient and testing the pipeline to required pressure For 160mm dia

Lowering, laying, jointing & testing of HDPE Pipes by butt fusion welding as per IS 7634-part-II/1975 as ammended from time to time to the alignment and gradient and testing the pipeline to required pressure For 110mm dia

Cost of MS Flanges including cost of Bolts, Nuts, Rubber Packing etc., complete and flange thickness confirming to IS:7322 - 1985 and flange dimensions confirming to IS:1538-1993 excluding Cost of MS barrel including cost and conveyance to site, excluding Taxes etc., complete. (Rate per each Flange). For 150 mm dia. x 15 mm thick

Manufacture, Supply and Delivery of Cast Iron Pipes and Fittings (spls.) Conforming to IS. No. 7181/1986, 5531/1988, 3950/1979 and C.I.D Joints confirming to is No.8794/1988 at site of work anywhere in A.P. Including, loading, unloading, transportation to site of work stacking at site transit risk and package, excluding taxes and duties.

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation. For 150mm dia PN-1.60

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation. For 100mm dia PN-1.60

Lowering, keeping in position and fixing C.I. sluice valves (with cap / with hand wheel & reflex valves) excluding cost of bolts, nuts, rubber insertion, sluice valve and tail pieces For 150mm. dia

Lowering, keeping in position and fixing C.I. sluice valves (with cap / with hand wheel & reflex valves) excluding cost of bolts, nuts, rubber insertion, sluice valve and tail pieces For 100mm. dia

Construction of Masonary Sluice Valve pits suitable to the sluice valves of size from as per TD No. 4/1941 including cost and conveyance of all materials and labour charges. Masonary pit valve for 100mm dia

Construction of Masonary Sluice Valve pits suitable to the sluice valves of size from as per TD No. 4/1941.including cost and conveyance of all materials and labour charges. Masonary pit valve for 150mm dia

Supply and Delivery of MS Flanges conforming to IS specification including cost and conveyance to site but excluding all taxes and duties. For 160mm dia

Supply and Delivery of MS Flanges conforming to IS specification including cost and conveyance to site but excluding all taxes and duties. For 110mm dia

Manufacture ,Supply, Delivery of HDPE long neck pipe ends suitable to HDPE pipes including transportation to any where in AP, but excluding Excise duty, Sale Tax and cost of specials etc., complete For 160mm dia

Manufacture ,Supply, Delivery of HDPE long neck pipe ends suitable to HDPE pipes including transportation to any where in AP, but excluding Excise duty, Sale Tax and cost of specials etc., complete For 110mm dia

Providing inter connection between to the existing pipe line and newly laid pipe line including of all necessary inter connection materials and washers and man mazdoorsetc., etc., complete as directed by the departmental authorities. For existing 250mm HDPE pipe line to proposed 160mm dia HDPE pipe

Providing laying spreading and compacting graded HBG crushed stone aggregate to Wet Mix Mecadam specification 5th Rivision as per table 400-13 including cost of all materials and including premixing the material with water at OMC in Mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in base courses on well prepared surface and compacting with vibratory roller to acheive the desired density etc. as directed by the Engineer-in-Charge and as per MORT & H specification 406( 5th rivision) for finished item of work

Providing concrete for plain concrete (M20 Design mix) using 343 Kgs Cement 40mm,20 mm,10mm nominal size Graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH