SPECIAL REPAIRS TO BLDG NO P-442 IN 777 SU AT AF STN BHUJ

Amount

Taking down existing water proofing treatment on RCC slab / beams with bitumen felt with out damaging structure and removing the debris outside the MD land and M&L for plaster 10 mm thick on concrete surfaces in cement mortar 1:3 finished even and smooth using WPC @ 3% by weight of cement and preparing the surfaces to receive WPT treatment , applying a coat of bitumen primer confirm to IS - 3384-1986 @ 3% per sqm . providing APP modified membrane with non wovenpolyester reinforcement/mat ( centre core) by touch application over primed surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for 5 mm thick rendering for fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:6 and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 15mm thick in Cement Mortar 1:4 (External) on Brick Walls or on Concrete Surfaces in Two Coats, 1st Coat of 10mm thick and 2nd Coat of 5mm thick including mixing with WPC to 2nd Coat as per Manufacturer's instructions, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and directed by Engineer-in-Charge. NOTE : Integral Water Proofing Compound shall be Measured and Paid separately as ‘Supply only’ under relevant Items.

Material & labour for preparing new Plastered Surfaces of Walls and applying Three Coats of White Wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new plastered Surfaces of Ceiling and applying Three Coats of White Was complete all as specified and directed by Engineer-in-Charge

Material & labour for preparing new Plastered Surfaces of Walls and applying Two Coats of Acrylic Washable Distemper over a coat of Chalk Whitening complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new or previously untreated concrete or PCC block masonry external surfaces and applying two coats of exterior emulsion paint (in camouflage pattern as approved by the GE) over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of plastered or unplastered old decorated external surfaces of walls and applying one coat of exterior emulsion paint in camouflage pattern as approved by the GE complete all as specified and directed by Engineer-in-Charge

Complete removal of existing treatment on wall surfaces and applying two coats of distemper with distemper oil emulsion, white or tinted including one coat of wall care putty by finishing the surfaces even and smooth complete all as specified and directed by Engineer-in-Charge

Material & labour for preparation of old painted sufaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint on steel and iron surfaces on roof coverings in camouflage pattern (as approved by GE) complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old painted sufaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint on wooden surfaces on roof coverings in camouflage pattern (as approved by GE) complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge

Material & labour for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM-1:6 complete all as specified and directed by Engineer-in-Charge.

Material & labour for glazed digital ceramic coloured tiles Ist quality in vertical surfaces such as in skirting and dados 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and icluding plaster 10mm thick in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & labour for Vitrified ceramic polished light shade tiles 10mm thick area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM-1:6 complete all as specified and directed by Engineer-in-Charge

All as per Ser Item No 17 above but in vertical surfaces such as dado, skirting and riser including rendering 10mm thick in CM 1:4 etc complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm eachcomplete all as specified and directed by Engineer-in-Charge

Supply & fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply & fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Supply & fix anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engineer-in-Charge

Material & labour for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out of JINDAL/ INDAL anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) all as specified and directed.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately complete all as specified and directed by Engineer-in-Charge

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm complete all as specified and directed by Engineer-in-Charge.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use complete all as specified and directed by Engineer-in-Charge.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use complete all as specified and directed by Engineer-in-Charge.

Material & labour for cutting chases, in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engineer-in-Charge.

Material & labour for 15mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge

Material & labour for 20mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs chromium plated fancy type bib taps 15mm bore, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge

Supply & fix in repair fancy type stop valve 15 mm bore chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge

Supply & fix in repair Angle Valve 15 mm bore chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

Supply & fix wash basin vitrous china (flat back and angle back Type) size 580x400mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe ,fixed in repair complete all as specified and directed by Engineer-in-Charge

Supply & fix in repair pillar taps of 15 mm bore, fancy type with capstan head, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge

Supply & fix waste pipe of 32mm dia PVC pipe for WHB with long screwed shanks and fly nut flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs Aluminium anodised tubular towel rail 20mm dia D Type 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Supply & fix grating square 150mm size of PTMT (minimum weight 100 gms ) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs PVC low level valve less, symphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 Ltr capacity complete all as specified and directed by Engineer-in-Charge.

Material & labour for PVC (SWR ) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge

Material & labour for 75mm dia cast iron floor trap with grating incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4 ) complete all as specified and directed by Engineer-in-Charge

Dismantling of cast iron,PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer-in-Charge following bore of pipe

110mm dia of pipe

75mm dia of pipe

Supply & fix PVC(SWR) drain self it pipes, single sockets ISI marked IS 13592 type 'B' in any length, jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed by Engineer-in-Charge following bore of pipe

110mm dia of pipe

75mm dia of pipe

Supply & fix PVC(SWR) junction single 'Tee' ISI marked IS 14735 jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed by Engineer-in-Charge following bore of pipe

110mm dia of pipe

75mm dia of pipe

Supply & fix PVC(SWR) bend equal ISI marked IS 14735 jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed by Engineer-in-Charge following bore of pipe.

110mm dia of pipe

75mm dia of pipe

Supply & fixing 1000 litre capacity Rotational moulded polythelene water storage tank ISI marked, cylindrical vertical with closed top including dismantling existing water tank and removing to store of following capacity complete all as specified and directed by Engineer-in-Charge.

Supply & fix PTMT shelf fixed to walls with chromium plated brass screws including necessary drilling holes complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china wash down water closet pan (pedestal pattern), white (exluding fixing bolts,flushing cistren and flushpipe) and including seat cover for pedestal pattern complete fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed by Engineer-in-Charge. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards /Blankets/Slabs, any description and any thickness including Cover Fillets, Cornices, etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing 12mm thick Gyp boards in ceilings fixed to ceiling sections with screws @ 300mm centre to centre and making good joints Gypsum binder including preparing the surfaces of ceiling boards and applying 2 coats of acrylic oil emulsion distemper with GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre, intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from sofits at approxly 900mm centre to centre with GI cleats, GI suspenders and steel expansion fasteners with and including ceiling section of 0.55mm thick having kurled web of 50 mm and flange of 26 mm each side with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre complete all as specified and directed by Engineer-in-Charge.

Material & labour for false ceiling corners with designed angular shape of size 100x100mm with POP fixed on 6mm thick fibre board with 20x20mm, 0.55mm thick galvanised sections fixed at intervals not more than 750mm complete all as specified and directed by Engineer-in-Charge.

Material & labour for alse ceiling of perforated particle board/tiles 60X60 cm in size and 12mm thick fixed with nails to timber frame work or with staples on snap grid fixed with screws in wall/ceiling, grid made of aluminium/G.I./M.S. as per specification and drawingcomplete all as specified and directed by Engineer-in-Charge.

Supply & fix Solid PVC Wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

Supply & fix 5 mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

Demolition Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

Material & labour for 100mm thick cement concrete type C2 1:3:6 ( using 40mm stone graded aggregate ) complete all as specified and directed by Engineer-in-Charge.

Material & labour for Cement Concrete 1:3:6 (using 40mm stone graded aggregate), 75mm thick as in Plinth Protection, etc., laid in alternate bays, finishing Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and directed by Engineer-in-Charge.

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound complete all as specified and directed by Engineer-in-Charge.

Material & labour for machine pressed precast concrete interlocking paver block any shape and size cofirming to IS 15658-2006 of 60mm thickness M35 grade with grey cemment and no pigments interstices filled with sand and bedded with and including 25mm thick sand cushion complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete in any position complete all as specified and directed by Engineer-in-Charge.

Demolition of PCC block masonry built in cement mortar complete all as specified and directed by Engineer-in-Charge.

Material & labour for precast cement concrete block masonry type 1:3:6 using 20mm graded stone aggregate with solid blocks, exc 10cm in width and setting in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & labour for Providing precast cement concrete Type B0 (1:2:4) using 12.5mm graded stone aggregate as in louvres and jallies, 25mm thick (measured solid) set cement moratar (1:4) including all mouldings complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces, finished even and fair without using extra cement. complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs sink with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 x 460 mm, bowl size 410 x 330 x 180 mm mm Make : Nirali (Model : elegance small from regular range, glossy) or size 915 mm x 460 mm bowl size 410 x 330 x 178 mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick 2nd class hard wood factory made plain framed, paneled shutters (any number of panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veveered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

Supply & fix 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cost or extraded sections and fixing bolts and sliding bolts of extraded sections or cost aluminium alloy complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100mm size of hinges butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

Supply & fix 150mm size extruded aluminium alloy handles, fabricated type complete all as specified and directed by Engineer-in-Charge.

Supply & fix 150 mm size aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-Charge.

Supply & fix 140mm floor door stopper of aluminium alloy body and tongue, anodised, fixed in floors complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new sufaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

Dismantling stone slabs and tiles of laid bedded and pointed in any mortar any description or thickness in floors, aprons etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for 20mm thick granite (Z Black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm thick screed bed of cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed by Engineer-in-Charge. NOTE : Cost of Screed Bed shall deemed to be included in quoted unit rate .

Material & labour for granite (Z Black) tiles 12 to 15mm thick machine cut, in vertical surfaces such as riser, skirting, dado, etc. including rounding edges, nosing, pointing on nose, etc., over and including 12mm thick screed bed in cement mortar 1:3 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete all as specified and directed by Engineer-in-Charge. NOTE : Cost of Screed Bed shall deemed to be included in quoted unit rate

Material & labour for reinforced cement concrete type A1, 1:1.5:3 using 20mm graded stone aggregate as in slabs supported on columns and beams complete all as specified and directed by Engineer-in-Charge. Note : Reinforcement shall be measured and paid separately.

Material & labour for providing precast reinforced cement concrete type A1, 1:1.5:3 using 20mm graded stone aggregate as in landings, cover slabs (for man holes etc) and similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match including use of necessary formwork and demolition / taking up of existing cover slabs & removing rubbish outside MD land complete all as specified and directed by Engineer-in-Charge.. Note : S&F reinforcement shall be measured and paid separately.

Supply & fix TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & fix TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Material & labour for formwork to sides and soffits of suspened slabs such as roof slabs, floor slabs, ladings and similar work, not exc. 200mm thick (horizontal or sloping) of rough finished concrete surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, rough finished concrete surfaces complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches, in any type of soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth , laying of cable or pipes (where provided for protection of cable) etc and getting out trimming the sides, forming bottom surfaces to required level complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches,hard/dwnse soil not exceeding 1.5 Mtr wide and exceeding 1.5 Mtr but not exceeding 3.0 mtr in depth , laying of cable or pipes (where provided for protection of cable) etc and getting out trimming the sides, forming bottom surfaces to required level complete all as specified and directed by Engineer-in-Charge.

Returning and filling including spreading, levelling, watering and well ramming in layers not exceeding 25 Cm thick complete all as specified and directed by Engineer-in-Charge.

Removing of surplus soil to a distance not exceeding 50 Mtrs and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up drain pipes of size 200 mm dia (Salt glazed ware, AC or reinforced concrete) set in cement mortar including the pipe inserted in Man holes walls etc. for undermentioned drain pipes, including removal of rubbish outside MD land complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing cement concrete 1:3:6 type C-2 bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for size 200 mm bore of pipe complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced concrete pipes, 200mm bore, class NP-2 laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing PCC 1:3:6, type C-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing cement concrete type B1, 1:2:4 mix (20mm graded aggregate) set in CM (1:6) in copings all as specified and directed including necessary use and waste of form work complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing cement concrete type B1, 1:2:4 mix (20mm graded aggregate) in benching in manholes all as specified and directed including necessary use and waste of form work complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 15mm thick in CM 1:4 mixed with water proofing compound on PCC block masonry surfaces finished even and smooth without using extra cement as specified. (Note : Supply only WPC will be measured and paid separately) complete all as specified and directed by Engineer-in-Charge.

Supply only inetergal water proofing compound complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants,regulators, sockets etc.incl removing materials to store for kepping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc complete all as specified and directed by Engineer-in-Charge.

Taking down main switch/DB’s including MCB’s with board and fixture of any description and making good disturbed surface of walls etc complete all as specified and directed by Engineer-in-Charge.

Taking down old light fittings of any description and making good disturbed surface of walls etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 Volts grade conforming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20mm dia (external) but shall be increased as per actual site requirement in accordance with clause No. 19.125 of SSR Part I ) ISI marked with wall thickness not less than 1.8mm with sunk cast iron/pressed steel terminal boxes made out of 1.2mm thick sheet including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5mm FRLSH PVC insulated unsheathed copper earth wire including Suitable for switches and sockets complete all as specified and directed by Engineer-in-Charge.

One light point controlled by one, one way switch single pole piano type

One Fan/exhaust point controlled by one, one way switch single pole piano type each

One 3 pin 5/6 Amps socket out let on independent board

One 3 pin 5/6 Amps socket out let on same board

All as per item No 105 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15/16 Amps socket out let on independent board. complete all as specified and directed by Engineer-in-Charge.

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor drawn through PVC Conduit and 4 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engineer-in-Charge. (Note: Two runs of conductor with one run of earth wire will be measured & paid as one unit)

Supply & fix in replacement recessed mounting LED 1X1 luminaire with white acrylic flat light dissipater with LED light source of 18 Watt of size 1’x1’(Feet) square shape suitable for False/POP ceiling including cutting the existing POP ceiling and fixing complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 20 W 4 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 10 W 2 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement energy saving, evironment friendly, long life, corrosion resistent, impact proof, Mini LED building security light made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LEDs with secondary optics and IP 65 protection with LED 20 W light source all as per Havells or equivalent in Orient/Philips/Bajaj/Crompton/Polycab including material and labour for suitable bracket made of 20 mm dia light grade GI pipe & MS clamps complete with nuts and bolts and washers complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement energy saving ceilling fan 1200mm sweep and connecting up including provision of cable from ceilling rose or connector to fan complete all as specified and directed by Engineer-in-Charge. Note Old u/s ceiling fan to be deposited at AGE E/M store yard

Supply & fix Metal body exhaust fan, AC single phase 230/240V of size 230 mm sweep with louvers including making hole of suitable size/ Alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-Charge. ( Note: Old unserviceable Exhaust Fan will be deposited in MES store yard).

Supply & fix PVC body exhaust fan, AC single phase 230/240V of size 300 mm sweep with louvers including making hole of suitable size/ Alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-Charge. ( Note: Old unserviceable Exhaust Fan will be deposited in MES store yard).

Supply & fix in replacement of ceiling fan regulator modular type electronic step type 5 step 360 deg 120 watt 2 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in Replacement ceiling rose surface bakelite 65mm x 50mm three terminal complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement, modular switch flush type, 6 Amp. SP, one way ,1 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular switch, 16 Amp flush type 1 module complete all as specified and directed by Engineer-in-Charge.

Material & labour for in replacement Modular socket 6A 5 pin 2 in 1 combined 2 module, 240 Volts complete all as specified and directed by Engineer-in-Charge.

Material & labour for in replacement Modular socket 6/16A twin type 2 module, 240 Volts complete all as specified and directed by Engineer-in-Charge.

Material & labour for in replacement modular metal flush box 3 module complete all as specified and directed by Engineer-in-Charge.

Material & labour for in replacement modular metal flush box 6 module complete all as specified and directed by Engineer-in-Charge.

Material & labour for in replacement modular metal flush box 8 module complete all as specified and directed by Engineer-in-Charge.

Material & labour for in replacement modular metal flush box 10 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular white cover plate with frame of module 3 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular white cover plate with frame of module 6 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular white cover plate with frame of module 8 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular white cover plate with frame of module 10 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix in Replacement double door Sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 triple pole and neutral 4 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-Charge.

All as per item No. 129 above but SPN 8 way with 200 Amp rated Busbar complete all as specified and directed by Engineer-in-Charge.

Supply & fix isolators/MCBs of the under mentioned type and rating and fixing in DBs (DBs measured and paid for separately) complete all as specified and directed by Engineer-in-Charge. (Note :- Make of the isolator should be the same as that of DB) for the following:

MCB TPN 415 volts 63 Amps Capacity, 10 KA

MCB SPN of 240 volts 20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Supply & fixing flame proof/weather proof 4 feet LED light fitting 2x18 Watt CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix flame proof exhaust fan, 12" (300mm), single phase,with and including louvers, complete all as specified and directed by Engineer-in-Charge. Note:-The rate quoated shall be in including making holes of suitable for exhaust fan of size 300 mm dia in PCC block masonry wall, making good the side of hole with CM (1:4) on wall with two coat of paint match with existing wall and distributed surface with 4 nos of stainless steel fastner of suitable size to fit the exhaust fan no extra payment will be allowed to contractor on this regard

Supply & fix flame proof exhaust fan, 15" (375mm), single phase,with and including louvers, complete all as specified and directed by Engineer-in-Charge. Note:-The rate quoated shall be in including making holes of suitable for exhaust fan of size 375 mm dia in PCC block masonry wall, making good the side of hole with CM (1:4) on wall with two coat of paint match with existing wall and distributed surface with 4 nos of stainless steel fastner of suitable size to fit the exhaust fan no extra payment will be allowed to contractor on this regard.

Supply & fix metal encosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 'C' series complete all as specified and directed by Engineer-in-Charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel as shown in electrical plate No.3 of SSR Part-I (2009) complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Material & labour for sand cushioning with a layer of sand 80 mm thick before laying of cable and 150 mm thick after laying of cable in trenches complete all as specified and directed by Engineer-in-Charge.

Supplying and laying un-reinforced precast concrete cable cover class LV, type - 2, flat, size 300x 180 x 40 mm complete all as specified and directed by Engineer-in-Charge.

Supply laying, jointing and testing cable XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc of size 50 sqmm, 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply & fix tubes light grade of 50 mm bore galvanised with all fitting for cable protection trenches/ wall/ on pole including necesarry clamps sets and nut & bolts complete all as specified and directed by Engineer-in-Charge.

Material & labour for cutting of existing road for laying GI pipe of size 50mm incl PCC work after laying the cable in GI pipe complete all as specified and directed by Engineer-in-Charge

Supply & fix GI tubing 25 mm bore, medium grade, ISI marked, with and including all fittings such as bends, elbows, tees, short pices etc compelete to wall and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Cutting & screwing extg steel tubing of size 25 mm dia for alterations or additions or lengthening screw on pipe to form connector and done in position complete all as specified and directed by Engineer-in-Charge.

Supply & fix gun-metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge

SHREE BHANU ENTERPRISE