COMPREHENSIVE MAINTENANCE TO JOINERY, FLOORING, PLASTERING, TILING , OTHER ALLIED WORKSAND PERIODICAL SERVICES IN OTM ACCN UNDER AGE B/R -II OF GE(A) BHUJ AT MIL STN BHUJ

Amount

Taking down existing chowkats or frames of any description and in any position exceeding 1.5 sqm n-exc 4.0 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

Taking down shutters of any description n. exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description and in any position exceeding 1 sqm & not exceeding 2 sqm each complete all as specified and directed.

Resecuring or easing & adjusting of shutters without taking down of any description exc 1.0 Sqm each but n. exc 2.0 Sqm each complete all as specified and directed.

Resecuring or easing & adjusting of shutters without taking down of any description n. exc 1.0 Sqm each complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply and fixing Solid PVC Door Frame of size 50mm x 95 mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Supply and fixing factory made solid PVC Moulded Door Shutter, With Particle Board Core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing on page no. 161 of SSR Part -II complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium sliding window with aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware i.e.. handles, barrel tower bolts, hinges etc, powder coated aluminium snap beading, screws etc. complete all as specified and directed Note : Alumnium frame ,Panel filling i.e.. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window & Ventilator shutters side hung type aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware i.e.. handles, barrel tower bolts, hinges etc, powder coated aluminium snap beading, screws etc. complete all as specified and directed Note : Aluminum frame, Panel filling i.e.. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

Material and labour for Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified Note : Aluminum frame, Panel filling i.e.. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

Supply and fixing 3mm thick figured glass ,pin head type and glazing with oil putty in square n.exc 0.5 Sqm in each pane etc all as specified.

Supply and fixing Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average with of aperture 1.40mm (weight not less than 600 gms /sqm )and fixed with aluminium wire staples/iron and wooden beads etc complete all as specified and directed.

Supply and fixing 12 mm thick prelaminated particle board, Exterior grade prelaminated and both sides with decorative choice laminations complete all as directed.

Supply and fixing factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003(Part - I) kiln seasoned and chemically pressure treated (35 mm thick with 2nd class HW rail and style) complete all as specified and directed.

Supply and fixing factory made 2nd class hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

Supply and fixing 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides compete all as directed.

Supply and fixing 25 mm thick Prelaminated particle, board, exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work as in wardrobe shutter, shelfs etc complete all as specified and directed.

Supply and fixing MS butt hinges medium weight cold rolled of size 100 mm complete all as specified and directed.

Supply and fixing 300 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified directed.

Supply and fixing 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Supply and fixing Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed .

Hacking out old broken glass (any thickness size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clip and providing and fixing new ones complete all as specified and directed.

Supply and fixing sheet glass 3 mm thick ordinary quality and glazing with oil putty or wooden beads in square, rectangle n.exc 0.5 Sqm in each pan all as specified and as directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed including taking down old one.

Supply and fixing in repair 300 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified directed.

Supply and fixing in repair 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Supply and fixing in repair Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed .

Material and labour for 2nd class hard wood (well seasoned) plain fillets, square, rectangular or triangular in section area exc 13 Sqcm and n.exc 25 Sqcm and secured with nails complete all as directed.

Supply and fixing Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on wooden frame/Pvc frame as per specifications and drawing

Material and labour for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Supply and fixing Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as directed.

Material and labour for PCC (1:2:4) type B-0 (using12.5 mm graded stone aggregate) as in holdfast block etc complete all as specified and directed.

Supply and fixing aluminium anodised floor door stopper 140 mm long all as directed by Engineer-in-Charge

Material and labour for preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed

Material and labour for for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces/stone masonry and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of the newly plastered surfaces of walls & applying two coats distemper oil- emulsion , white or tinted over a coat of primer surfaces of wall complete all as specified and directed.

Material and labour for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

Material and labour for Rendering 15 mm thick of CM 1:4 on fair faces of brick or concrete surfaces is to be finished even and smooth without using extra cement with mixing of water proofing compound complete all as directed.

Material and labour for Providing and applying cement base plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Supply only water proofing compound (WPC- ISI Mark) all as directed by Engineer-in-Charge

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as directed

Material and labour for Cement concrete ( 1:3:6) type C- 2, using (40mm graded stone aggregate) 75 mm thick as in sub base /plinth protection etc. Finishing cement concrete surface even and smooth without using extra cement complete all as directed.

Material and labour Machine pressed precast concrete rubber moulded interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

Material and labour for sand filling under floors or in foundation including watering and consolidation all as directed by Engineer-in-Charge

Material and labour for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

Material and labour for glazed coloured ceramic tiles in vertical surface of size 450x300x7 mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match for surface of tiles, over 10 mm thick backing coat with cement mortar 1:4 complete all as specified and as directed.

Material and labour for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

Material and labour for ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick as in skirting fixed over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

Taking down steel window and fixing in same opening after making serviceable by welding , providing hinges and peg stay, PCC for holdfast etc including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete and making good the disturbed surface as directed by Engr-in-charge.

Supply and fixing butt Hinges, medium weight, stainless steel, 100 mm size complete all as specified.

M & L for powder coated aluminium grill of design No DG-104, 7.5mm thick sections of deco grill or of equivalent approved make with 1 mm thick 'F' sections of suitable size complete all as specified and directed by Engr in Charge.

M & L in repair for Curtain rod, powder coated aluminium alloy of 25mm dia pipe decorative finish with and including supply and fixing powder coated decorated type brackets, stops, rollers etc. fixed on walls with brass screws with PVC rawl plugs as in curtain rods complete all as specified and directed.

Preparation of old decorated surfaces of comougflage wall pattern including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove dust, dirt and loose scales of cement paint and other foreign material, scrapping down, moss and efflorescent salts, washing, rubbing down and stopping of painted surface and Material and labour for applying one coats of cement base paint incl watering and curring of surfaces adequately before and after application of cement base paint compelete all as specified and directed.

Preparation of old painted surface of concrete and concrete based materials of any description and in any position over 10 cm width or girth and Material and labour for applying one coat of synthetic enamel paint complete all as specified and directed. by Engr-in-Charge.

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and Material and labour for applying one coat of white wash , complete all as specified and directed. by Engr-in-Charge

Preparation of old decorated surface of ceiling and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying one coat of white wash complete all as specified and directed.by Engr-in-Charge

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and M & L for one coat of colour wash on wall complete all as specified and directed.

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and Material and labour for applying one coat of cement base paint including watering and curing of surface adeqautely before and after application of cement base paint complete all as specified and directed.

Preparation of old decorated plastered or unplastered surfacesof wall including washing , rubbing down and stopping of distempered surface Material and labour for for applying one coat of distemper oil emulsion paint white or tinted complete all as specified

Preparation of old painted surface of wood and wood based material any description and in any position over 10 cm width or girth and Material and labour for applying one coat of synthetic enamel paint complete all as specified and directed. by Engr-in-Charge.

Preparation of old painted surface of steel and iron surface of any description and in any position over 10 cm width or girth and Material and labour for applying one coat of synthetic enamel paint complete all as specified and directed. by Engr-in-Charge.

Complete removal of existing treatment on wall (any number of layers ) by scarping with steel scapers or any other mean and applying external wall care putty in two layer 1mm thick and making surface even and smooth to receive external emulsion and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as Specified and directed.

Material and labour for writing letters or figures using fluorecent paints (Block, Roman, Italic or Indian) n exc 30 cm high over and including black painted surfaces (back ground) complete all as specified and directed by Engr-in-Charge.

Material and labour for stops , commas shortlines dashes hypens brackets using fluorecent paints etc complete all as specified and diretecd

Material and labour for rendering 15 mm thick in CM 1:6 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed .

Material and labour for preparation of newly plastered surfaces of work and applying two coats of cement base paint all as specified and directed.

Providing & applying Rising damp-proof coating system with Single component ready to use damp-proof coating Roff Hydamp : 1.SURFACE PREPARATION: Thoroughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc. All large voids or hollow portions must be removed and re-plastered. Non- moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2 APPLICATION: Apply the first coat of Dr Fixit Dampguard Classic with a paintbrush directly on the prepared surfaces by mixing ( 1 part base:1 part hardner: 1 part of water) . Allow to dry for a minimum 2-3 hrs. Apply one part of DAMPGUARD mixed chemical and 2 parts of OPC white cement/Birla Putty and make the Putty, apply Putty on the entire surface area. Allow it to dry for at least 3-4 hours. Apply the Final coat of Dr Fixit Dampguard Classic on the entire surface and allow the surface to air cure 48 Hrs proceeds to paint.

Material and labour for preparation ofold plastered surfaces of work and applying two coats of texture paint all as all as per manufaturer instruction.

M/s Bombay Novelty Stores

zotabrothers